Lumiscope 1131 User's Manual
Contents
1. After a memory zone is selected press th D button to reset the monitor so it can start measurement in the chosen memory zone 2 Press the D button All digits will light up checking the display functions The checking procedure will be completed after about 2 seconds 3 After all symbols vp zz oc 3 gt TI padai D m pm appear display will show a blinking 0 The monitor is now ready to measure and will automatically J Te eo cc inflate the cuff slowly to start measurement oy Measurement Procedure 4 When the measurement is completed the cuff will automatically deflate Systolic diastolic and pulse will be shown simultaneously on the LCD screen The measurement is then automatically stored into the pre designated memory zone Note 1 This monitor automatically switches off approximately 1 minute after last measurement 2 To interrupt the measurement simply press any key The cuff will deflate immediately after any key is pressed 3 Do not talk or move your arm or hand muscles during measurements Recalling Values from Memory 1 The Monitor has two Memory Zones 1 and 2 Each zone can store up to 50 measurements 2 To read memory values from a selected Memory Zone use the User Switching Key to select a Memory Zone 1 or 2 from which you want to recall values from Then press the M key and the values will be shown on the LCD displ2. G W No Batteries Adult 24 36 cm 9 4 14 2 standard Large adult 34 46 cm 13 4 18 1 standard Short time operation 2 minutes Specifications are subject to change without notice 16 Two Year Limited Warranty Lumiscope guarantees this product free from defects in material and workmanship for a period of two years from the date of purchase except as noted below This Lumiscope product warranty does not cover damage caused by misuse or abuse the attachment of any unauthorized accessory alteration to the product or any other conditions whatsoever that are beyond the control of Lumiscope Lumiscope shall not be responsible for any type of incidental consequential or special damage All implied warranties including but not limited to those implied warranties of fitness and merchantability are limited in the total duration of two years from the original date of purchase To obtain warranty service on your Lumiscope Blood Pressure Monitor please contact the Lumiscope Repair Department at 1 800 672 8293 or visit www lumiscope net There is a 15 fee for return shipping and handling Please make checks payable to The Lumiscope Co Inc Upon receipt Lumiscope will repair or replace as appropriate the blood pressure monitor and return it to you Warranty is solely through the Lumiscope Repair Department Service of this product by anyone other than the Lumiscope Repair Department voids warranty In the ev
3. LUMISCOPT AUTOMATIC UPPER ARM Blood Pressure Monitor Model 1131 Features e Dual Person Memory Zones e 50 Memories for each zone e Average for Last 3 Memories e Date and Time Stamp e One Touch Operation Table of Contents Introduction 0 sccccccssscessessseees 2 Name Function of Each Parts 2 Quick Read Measuring Technology 3 Preliminary Remarks 0 cccssscssses 3 About Blood Pressure 2 000 3 Blood Pressure Standard 000 0 4 Blood Pressure Fluctuation 4 Display Explanation 0cc cccssscsssse 5 Installing Battery 0 ssccsccssscsssee 6 Applying the Cuff sscsss0 7 Measurement Procedures 8 9 Recalling Values from Memory 10 Clearing Values from Memory 11 Time Adjustment s 0ssse0es 12 Helpful Wipsecsirrecsscocteccceccccceccceseser 13 Troubleshooting cccssscsssssssseees 14 Cautionary Notes cccsssssssee 15 Specifications ssssssseccsssessseeees 16 Introduction Blood pressure measurements determined with Lumiscope Model 1131 are equivalent to those obtained by a trained observer using cuff stethoscope auscultation method within the limits prescribed by the American National Standard Electronic or Automated Sphygmomanometers This monitor is to be used by adult consumers in a home environment Lumiscope Model 1131 is protected against manufacturing defects by an establish
4. apter into a standard wall socket Caution 1 Please unload the batteries when operating with the AC mode for a longer period of time Leaving the batteries in the compartment fo a long time may cause leakage which ma lead to damage of the unit 2 No batteries are needed when operating with the AC adapter Applying the arm cuff 1 Plug in the cuff connecting tube into the unit 2 Unwrap the arm cuff leaving the Index end of the cuff through the D ring of the cuff 3 Put your left arm through the cuff loop The OK range indication should be positioned closer to yourself with the rubber tube pointing in the direction of your arm Position the artery mark Q over the main arteries on the inside of your arm in the upper arm N is Artery 2 3 cm 0 8 1 2 4 Turn your left palm upward and place the edge of the arm cuff at approximately 2 _ to cm above the inner side of the elbow joint Tighten the cuff by pulling the Index end of the cuff o If the Index line falls within the OK range indicated at the edge of the cuff this cuff suitable for your use If the Index line falls out the OK range you may need a special cuff measurement Please visit www lumiscope net contact our service department at 800 672 8293 for more information regarding Measurement Procedure 1 Press the User Switching key to select Memory Zone 1 or Memory Zone 2 Clk 18 or 28
5. ay with an assigned memory sequence number Se 10 The monitor will display an average of the previous measurements first Every new press of the M key Calls for one set of prior values stored Latest memory will be recalled first The calculated average will be applied to a maximum of the last 3 memories Cag 19128 A ae 4 bot a aay qe I pm ti 3H mee r aa 18 qe us 4s 14 i 4 cr f i re j J mem a J mem on Y nA uo Y 9 aes Clearing Values from Memory 1 Press the User Switching key to select the memory zone 1 or memory zone 2 Cag 2 Continue to press and hold the M key for approximately 5 seconds and the data in the pre designated memory zone will be erased automatically bot rm ka aa ra Press M Key for 5 seconds to clear all memories m Y 3 oO 3 7 f Note The data in both memory zones zone 1 and zone 2 will be erased if any of the batteries are removed or if the AC adapter is disconnected from the unit or unplugged from the outlet It is suggested that users record their data on the Blood Pressure Log before removing or replacing batteries 11 Time Adjustment 1 To adjust the date time in the monitor press the key The display will show a blinking number showing the month 2 Change the month by pressing the G Key Each press will increase the number by one in a cyc
6. ealth problems today problems associated with high blood pressure are by far the most common High blood pressure s dangerously strong correlation with cardiovascular diseases has made measuring blood pressure a necessity for identifying those at risk Blood Pressure Standard The World Health Organization WHO has developed a blood pressure standard according to which areas of low and high risk blood pressure are identified This standard however is a general guideline and blood pressures vary between different people age groups etc It is important that you consult with your physician regularly Your physician will tell you your normal blood pressure range as well as the point at which you will be considered at risk Systolic gt 160 Stage 2 Hypertension esoies 100 q 100 Systolic 140 159 A a ystolic 90 Stage 1 Hypertension Diastolic 90 99 Systolic 120 139 2 80 Prehypertension Diastolic 80 89 pa Systolic 90 119 Ban Normal Diastolic 50 79 Hypotension Systolic lt 89 Diastolic lt 49 90 120 140 160 Systolic mmHg gt Blood Pressure Fluctuation Blood pressure fluctuates all the time You should not be overtly worried if you encountered two or three measurements at high levels Blood pressure changes over the month and even throughout the day It is also influenced by season and temperature mmHg 200 F Fluctuation within a day Case Male 35 years old Sy
7. ed International Warranty Program For warranty information see page 16 or contact the Lumiscope Repair Department at 1 800 672 8293 N Attention Consult the accompanying documents before use e Please read this manual carefully before use for specific information on your own blood pressure contact your physician Please be sure to keep this manual Name Function of Each Part User Switching Key LCD Display Date Time Set Key Memory Recall button Arm Cuff Air Tube and Connector COLOCO 4 x AW size 1 5V Batteries Quick Read Measuring Technology This monitor uses trend setting Quick Read Technology to detect your blood pressure With one touch of a button the device will automatically start to inflate and determine your blood pressure by analysis of your pressure oscillations When the measurement is completed the device will exhaust cuff pressure and display your systolic diastolic and pulse Measurement time is significantly shortened and user comfort is greatly enhanced About Blood Pressure What is Blood Pressure Blood pressure is the pressure exerted on the artery tube while blood flows through the arteries The pressure measured when the heart contracts and sends blood out of the heart is systolic highest The pressure measured when the heart dilates with blood flowing back into the heart is Called diastolic lowest blood pressure Why Measure Your Blood Pressure Among the various h
8. ent that Lumiscope does not abide by the terms of this warranty the consumer may seek breach of contract remedies in the New York State Federal courts of law This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you Distributed By The Lumiscope Co Inc www lumiscope net Repair Department 1 800 672 8293 Made and Printed in China 17
9. ling manner Press th Key again to confirm the entry and the screen will show a blinking number representing the date 3 Change the date the hour and the minute as described in Step 2 above using the Key to change and the Set Key to confirm the entries 4 A 0 will reappear as the Blood Pressure Monitor is ready for measurement again Press the Set key 4 blinking month 4 increasing month 4 confirm the entry xy S447 tc UE mont ota aS 12 Helpful Tips Here are a few helpful tips to help you obtain more accurate readings e Do not measure your blood pressure immediately after consuming a large meal Wait at least one hour after eating to take a measurement e Do not smoke or drink alcohol before measuring your blood pressure e You should not be physically tired or exhausted while taking a measurement e t is important that you relax during measurement Take 15 minute rest before a reading e Do not take measurements if you are under stress or under tension e Take your blood pressure at normal body temperature If you are feeling cold or hot wait a while before taking a measurement e f the monitor is stored at very low temperature near freezing have it placed at a warm location for at least one hour before using it e Wait about 5 minutes in between consecutive measurements 13 Troubleshooting If any abnormality should arise during use please check the fol
10. lowing points Symptom Check Point Correction No display when the i i ON OFF START Have the batteries run Replace them with four key is pressed down new batteries or use AC Adapter Have the batteries polarities been positioned incorrectly Re insert the batteries in the correct positions EE mark shown on display or the blood pressure value is displayed excessively low high Is the cuff placed correctly Wrap the cuff properly so that it is positioned correctly Did you talk or move during measurement Did you vigorously shake the cuff during measurement Measure again quietly Note If the unit still does not work return it to your dealer or contact our repair department Under no circumstance should you disassemble and attempt to repair the unit by yourself 14 Cautionary Notes 1 The unit contains high precision assemblies Therefore avoid extreme temperatures humidity and direct sunlight Avoid dropping or strongly shocking the main unit and protect it from dust 2 Clean the blood pressure monitor body and the cuff carefully with a slightly damp soft cloth Do not press Do not wash the cuff or use chemical cleaner on it Never use thinner alcohol or petrol gasoline as cleaner 3 Leaky batteries can damage the unit Remove the batteries when the unit is not used for a long time 4 The unit should not be operated by children so to avoid hazard
11. ous situations 5 If the unit is stored near freezing allow it to acclimate at room temperature before use 6 Your Lumiscope Model 1131 is not field serviceable You should not use any tool to open the device nor should you attempt to adjust anything inside the device If you have any problems please contact the store or the doctor from whom you purchased Lumiscope Model 1131 or contact the Lumiscope Repair Department at 1 800 672 8293 7 For users diagnosed with common arrhythmia atrial or ventricular premature beats or atrial fibrillation diabetes poor circulation of blood kidney problems or for users who have suffered from stroke the device might not be suitable for use 8 Do not use on unconscious patients 15 Specifications Measurement Method Measurement Range Pressure Sensor Accuracy Inflation Deflation Memory capacity Auto shut off Operation Environment Storage Environment Power Source Dimensions Weight Arm circumference K B Oscillometric Pressure 20 280mmHg Pulse 40 180 beats minute Semi conductor Pressure 3mmHg Pulse 5 of reading Pump Driven Automatic Pressure Release Valve 50 memories for each memory zone 1 minute after last button operation Temperature 5 C 45 C 41 F 113 F Humidity 40 85 Temperature 10 C 60 C 14 F 140 F Humidity 10 95 6V DC four LROG AA Batteries 137 L X 140 W X 63 H mm 450g
12. stolic pressure 150 F Diastolic pressure Discussion Argument Wake Arrive on the ina Leave Dinner 50 up office telephone meeting office Sleep T T T T 06 00 12 00 18 00 24 00 Display Explanation Display Icons Memory Zones 18 28 Date Time indicator Systolic Pressure Diastolic Pressure Pulse Rate Memory Number Memory Zone 1 Appears when the monitor is operated in memory zone 1 Memory Zone 2 Appears when the monitor is operated in memory zone 2 Weak Battery Mark Appears when batteries should be replaced Pulse Mark Shows the pulse rate per minute Memory Mark Shows the number of stored measurements Error Mark Occurs when a mistake was made during measurement Installing Battery 1 Press down and lift the battery cover in the direction of the arrow to open the battery compartment 2 Install or replace 4 AA sized batteries in the battery compartment according to the indications inside the compartment 3 Replace the battery cover by clicking in the bottom hooks first then push in the top end of the battery door You need to replace the batteries when 1 low battery icon appears on display 2 the ON OFF START button is pushed and nothing appears on display Caution Batteries are hazardous waste Do not dispose together with the household garbage Using the AC adapter 1 Connect the AC adapter with the AC adapter jack in the back of the unit 2 Plug the AC ad
Download Pdf Manuals
Related Search