Home
Lightolier Work Light MHCR User's Manual
Contents
1. MutTISET MULTISET PRO CHANNEL REMOTE MurriSet MuttiSer Pro MSCR MHCR operon Specifications me METTET LIGHTOLIER SEA LAON AND ees a a Remote OPERATION S oltage A MANUAL Output Current 2 5 ma Models Low wattage MSCR High Wattage MHCR Operating Temperature 0 to 40 C Dimensions H W D Wt oz MS Models 4 1 11 16 1 7 8 4 0 MH Models 4 1 2 2 9 16 1 7 8 5 0 Colors MS Models White Ivory MH Models White Black Grey and Almond are custom colors consult factory Ur US LISTED THREE YEAR LIMITED WARRANTY The Philips Controls product when properly installed and under normal conditions of use without overload abuse or alteration is warranted to you the original user for a period of three years form the date of original retail purchase to be free from defects in materials and workmanship If during the warranty period you believe the purchased product or any part thereof has such a defect you must return the product or part at your cost during such period with proof of purchase or if installed by a third party a written explanation of installation transaction with proof of date to Philips Controls 2828 Trade Center Dr Ste 130B Carrollton TX 75007 for repair or replacement or to an authorized Philips Controls supplier which agrees in advance to handle the return and replacement by factory authorization If the product or part is found by Philips Controls to have been defectiv
2. aise lower and three way of a specific dimmer Caution Caution Be sure that power to the circuit being controlled has been disconnected by removing fuse or turning circuit breaker off Installing device with power on may expose you to dangerous voltage and damage the device Installation Instructions Instructions Note 1 If replacing an existing device with this device begin with Step 1 of Installation section Note 2 If installing this device in new construction begin with Step 4 of Installation section Reminder Disconnect power at panelboard 1 Remove faceplate from existing device 2 Unscrew and pull device out of wallbox 3 Disconnect wires from device Using a wire box tester identify and mark the Hot and the Traveler wires connected to device 4 Install device per the following notes IMPORTANT 4a Be sure Multiset Ground wire bare stranded is connected to earth ground Note Miswiring or failure to connect ground may result in improper operation of device 4b If using Compli faceplate sold separately Before connecting any wires be sure the Compli faceplate mounting frame is behind the device with alignment tabs facing forward Tabs should rest within centering holes of Remote s aluminum mounting strap 5 After all connections have been made see wiring diagram and notes be certain all wire connectors are firmly attached Gently place wires and backbox into wallbox with LED at top of devi
3. ce and screw in place Before installing faceplate restore power to circuit After testing device for proper operation install faceplate onto the device L NA 2 PHILIPS LED Indicator Fig A Glowing RED Power On C Operating Instructions TURN LIGHTS ON TO PRESET e Tap rocker top once A c TURN LIGHTS FULL ON e Tap rocker top twice A ADJUST LIGHT LEVEL A e Press and hold down rocker top or bottom until desired level is reached A or B e Release rocker B TURN LIGHTS OFF e Tap rocker bottom once or twice B e Lights Fade off Note When properly installed the Red LED on the remote will be constantly Fig A lit at half brilliance Wiring Notes Multiset Remote to Wallbox Wire Black Hot 120V Source Must be same phase as dimmer Yellow Traveler Wire from MultiSet MultiSet Pro Dimmer On switch Bare Copper Earth Ground Grey Ground or Neutral For Remote LED operation connect grey to neutral or ground Note 1 MSCR MHCR can control one MultiSet MultiSet Pro Dimmer or switch from one or multiple locations Note 2 MSCR MHCR must be wired on the same circuit as the device it is controlling Note 3 MSCR MHCR provides manual override for any one device channel of a MultiSet MultiSet Pro system Note 4 Each circuit feeding dimmers and dimmed loads requires a separate neutral Shared neutrals will result in undesirable flashing of controlled loads Note 5 Line voltage must not be supplied b
4. e in material or workmanship it will be repaired or replaced as deemed necessary by Philips Controls and the replacement will be returned to you free of charge The original user is solely responsible for any costs associated with removal and re installation of the product and shipping to Philips Controls or its authorized supplier PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH ABOVE AND OTHERWISE DISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS Some states disallow certain limitations on implied warranties so you should consult your state law if you have a questions regarding this limitation and disclaimer Philips Controls disclaims any and all liability for incidental consequential special or indirect damage arising out of any claimed breach of warranty or otherwise However some states do not allow exclusion or limitation of such damages so this disclaimer may not apply to you The remedy provided in the Limited Warranty for defective products is the user s sole and exclusive remedy subject to your state law Further this Warranty gives the user specific legal rights and the user may also have other rights which may vary from state to state If you believe warranty claim is warranted you may contact your nearest authorized Philips Controls supplier If one does not exist in your area please contact Philips Control
5. s Customer Service at the above address or at 1 800 526 2731 or please visit us at FOR USE WITH MODELS www lolcontrols com MSCR MHCR Remote for raise lower and on off control of a channel Exchange of products covered by warranty should be handled through your original supply source We reserve the right to change details of design materials and finish in any way that will not alter installed appearance or reduce function performance Designer Style Multi Location Digital Remote or technical sales assistance call Lightolier Controls 1 800 526 2731 Control To Be Used With MultiSet Dimmers 2828 Trade Center Drive Suite 130B Carrollton Texas 75007 Made in U S A Philips Controls 1997 MUTTISET MULTISET PRO MSCR MHCR Installation and Operation Description The MultiSet Multiset Pro Channel Remote is a designer style full function multi location remote device that uses existing three way wiring to control MultiSet MultiSet Pro dimmers or switches Channel Remotes use standard 3 way wiring see wiring diagram for details Features A Streamlined appearance and operations A red LED light to help locate the device in a dark room As an individual device the MultiSet MultiSet Pro Channel Remote has the capability to recall two presets a user selected on level and full brightness When used with a MultiSet MultiSet Pro Scene Master the remote has additional applications on off r
6. y a GFI Breaker Wiring Diagram Diagram Note No common neutrals on dimmed circuits To Load To Load To Load AN Master MS 5 PHILIPS
Download Pdf Manuals
Related Search
Related Contents
Reebok Fitness 30711.0 Home Gym User Manual TAFCO WINDOWS NU2-121V-I Instructions / Assembly Ressource Impression du journal io-em-008 pulizia apparecchiature area lavorazione sangue notice IMODIUMCAPS Descuento en Buffet Libre y los Niños... ¡Gratis! Notice d`instruction et de service SBS TE0PSE35K mobile phone case Manual de usuario y servicio Visco Probe Copyright © All rights reserved.
Failed to retrieve file