Lightolier IS:6079 User's Manual
Contents
1. GROUND RELEASE2. NSTRUCTIONS FOR CONVERTING FITTING TO OPERATE ON 2 CIRCUIT TRACK SYSTEMS See Fig 5 BRASS CONTACT can be raised or lowered Broken line indicates position for 1 circuit l track or lower circuit of 2 circuit track system LOCKING To convert attachment FITTING for upper circuit of 2 circuit track raise BRASS CONTACT to high LEVER position by lifting CONTACT as high as stop permits and CONTACT dicks into place FIG 5 INSTRUCTIONS FOR ATTACHING EXTENSION WAND TO EXTENSION WAND SLOPED CEILING ADAPTER 1 Insert the WAND FITTING into the LOWER FITTING The LOCKING LEVER must be on the same side as the bead located at the bottom of the LOWER FITTING See Fig 6 Rotate the WAND FITTING 90 clockwise until LOCKING LEVER snaps and locks in place See Fig 6 7 amp 8 2 To remove depress LOCKING LEVER and rotate FITTING 90 counterclockwise LOWER FITTING BEAD BRASS CONTACT DOWN LOCKING m WAND CLOCKWISE LEVER FITTING BCS PB CD BBE FR hoire oues canana INSTRUCTION SHEETNO INSTALLATION FOR ATTACHING EXTENSION WAND SLOPED IS 6079 CEILINGS ADAPTER TO LYTESPAN TRACK FOR USE WITH lite LYTESPAN TRACK SYSTEMS ONLY Continued INSTRUCTIONS FOR ATTACHING LYTESPOT FIXTURES WITH SQUAT ADAPTER TO WAND SLOPED CEILING ADAPTER 1 Insert the FIXTURE FITTING into the WAND SOCKET The LOCKING LEVER must be on the same side as the bead located at the bottom of the wand See Fig 9 Rotate the FIXTURE FITTING 90 clockwise unt
3. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations gt To assure full compliance with local codes and regulations check with your local electrical inspector before IS 6079 installation To prevent electrical shock tum off electricity at fuse box before proceeding E Retain these instructions for maintenance reference 0493 Page 1 of 2 INSTALLATION FOR ATTACHING EXTENSION WAND SLOPED CEILINGS ADAPTER TO LYTESPAN TRACK FOR USE WITH LYTESPAN TRACK SYSTEMS ONLY Extension wand sloped ceiling adapter can be mounted on any Basic Advent Multipoint or Monopoint Track on ceilings from 0 to 90 vertical Not for use with Lytespots with attachment fitting 7589 1 Grasp TOP FITTING at top of ADAPTER and insert it into the LYTESPAN TRACK The LOCKING LEVER must be on the same side of the track as the BEAD See Fig 1 Rotate the TOP FITTING 90 clockwise See Fig 2 until LOCKING LEVER snaps and locks in place See Fig 3 Do not rotate adapter from LOWER FITTING Loosen KNOB and set the lower half of the ADAPTER to a vertical position and tighten KNOB Fig 4 To Remove Depress LOCKING LEVER then rotate TOP FITTING 90 counter clockwise Do not rotate wand from LOWER FITTING LYTESPAN TRACK Ea BEAD FITTING LOCKING LEVER LOCKING 7 C LOWER FITTING LEVER T CLOCKWISE FIG 1 FIG 2 I
4. il LOCKING LEVER snaps and locks into place See Fig 9 10 amp 11 2 To remove depress LOCKING LEVER and rotate FITTING 90 counterclockwise BRASS CONTACT DOWN m FIXTURE FITTING FIG 9 INSTRUCTIONS FOR ATTACHING LOW VOLTAGE LYTESPOT TO WAND SLOPED CEILING ADAPTER 1 Insert the FIXTURE FITTING into the WAND SOCKET The LOCKING LEVER must be on the same side as the bead located at the bottom of the WAND SOCKET See Fig 8 Rotate the FIXTURE FITTING 90 clockwise See Fig 12 13 amp 14 To remove rotate FITTING 90 counterclockwise FIXTURE FITTING De Carer FIG 12 FIG 13 FIG 14 INSTRUCTIONS FOR ATTACHING LYTESPOT WITH T ADAPTOR TO WAND SLOPED CEILING ADAPTER 1 Align BEAD on WAND SOCKET with GROOVE in FITTING before inserting into WAND SOCKET see Fig 15 If BEAD is NOT aligned a potential hazard may result 2 Position LEVER as shown in Fig 15 3 Insert FITTING into WAND SOCKET Turn LEVER 90 to make mechanical and electrical connection See Fig 16 4 To remove reverse procedure NOTE If T ADAPTOR has a full gasket on top remove 1 2 strip of cork between contact hub and grounding spring If there is no gasket and a tighter fit to the WAND is desired remove backing from enclosed GASKET When centered on FITTING apply pressure on GASKET to secure it IL SHARD BOX ADAPTOR CONTACT HUB GROUNDING SPRING REMOVE CORK AND PAINT IF PRESENT FROM THIS AREA TO INSURE PROPER
Download Pdf Manuals
Related Search