Lightolier IS:40431 User's Manual
Contents
1. and connections back into OUTLET BOX CANOPY a CAUTION MAKE CERTAIN WIRES ARE NOT PINCHED CANOPY WARING BETWEEN PARTS SCREW L SCREW 3 Secure STEM ASSEMBLY to OUTLET BOX using OUTLET BOX aia sain SCREWS Thread OUTLET BOX SCREWS into OUTLET BOX Pass OUTLET BOX SCREWS through SLOT in SWIVEL PLATE and twist HANGER BRACKET through KEYHOLE Fully tighten screws DOOR 4 Slide CANOPY up STEM and attach CANOPY to SWIVEL PLATE using CANOPY SCREWS ae all Nl POWER HEAD INSTALLATION NS gt mi Slide STEM through opening in HANGER BRACKET To secure NHS STEM align holes and push PIN into holes Push COTTER PIN eee ecm gt ea aap through hole at the end of PIN to secure PIN in place as shown NECK h i in fig 2 Ce COLLAR 2 Align KEYHOLE in MOUNTING PLATE with SCREWS in TOP Sun TAB MOUNTING PLATE and twist into position Fully tighten SCREWS SET SCREW een eee REFLECTOR PLATE 3 Remove DOOR from POWERHEAD by loosening SCREW in TOP MOUNTING PLATE SCREW is located directly above PIN on REFLECTOR POWERHEAD DOOR which protrudes through BOTTOM PLATE Pull DOOR directly away from POWERHEAD 4 Using WIRE NUTS local hardware item wire fixture COMPACT FLUORESCENT and INCANDESCENT FIXTURES Black fixture lead to hot black stem lead white stem lead to neutral white supply lead Attach green ground wire from BOTTOM PLATE to green ground wire from stem lead and BALLAST if supplied METAL HAL2. IDE FIXTURES Refer to wiring diagram illustration in fig 4 5 Reinstall door and secure in place by tightening SCREW through TOP MOUNTING PLATE 6 Install recommended lamp s Note On metal halide fixtures with auxiliary light option install halogen lamp as shown in Fig 3 CAUTION MAXIMUM WATTAGE AS MARKED ON FIXTURE MUST NOT BE EXCEEDED CC REFLECTOR INSTALLATION ae 1 Slide COLLAR up extruded NECK 2 Tip REFLECTOR over REFLECTOR PLATE and allow REFLECTOR CONNECT TO to rest on TABS APPROPRIATE VOLTAGE 3 Slide COLLAR down over REFLECTOR and secure in place by a loosening two SET SCREWS in extruded NECK allowing SET SCREW to extend outward enough to hold COLLAR in position LENS INSTALLATION when provided Le 1 Place LENS up into lip of REFLECTOR Secure in place by opening HID BALLAST RING around lip of REFLECTOR and allowing spring tension to hold in place FIG 4 i j Cs i TO i i j i LIGHTOLIER a GENLYTE THOMAS company EEE BLK GROUND POWERCORD 631 Airport Road Fall River MA 02720
3. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before z 40 43 1 a installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference 1198 Page 1of 1 INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION OF 12 amp 16 PENDALYTE SERIES WITH STEM Note This instruction sheet covers several fixture styles OUTLET BOX Powerhead assembly lamp type and reflector may WIRE NUTS vary slightly from that shown although installation is the same Pani ae INSTALLATION Rotate BALL so that side hole comes into view Install end of SWIVEL i PIN PIN STEM into BALL lining up holes Install SPLIT PIN into holes and PLATE i gt r a allow BALL STEM to swing into resting position trapping the PIN T i Sio into place SPLIT PIN i 4 2 While supporting STEM ASSEMBLY make connections black ae OUTLET BOX STEN stem lead to hot black supply lead white stem lead to neutral BALL PEE SCREW ANEN white supply lead Green stem wiring wire is a ground wire and Z O must be connected to grounding terminal or ground lead inside STEM i l OUTLET BOX Use WIRE NUTS local hardware item Push supply b LI g wires
Download Pdf Manuals
Related Search