Life Fitness Sport and Essential Consumer Treadmills User's Manual
Contents
1. Life Fitness Sport Essential and Bally s Consumer Treadmills Bushing Replacement Service Kit HEA BUSHINGKIT HEA BUSHINGKIT consists of e Bushing Spacer ZHEA50720 2 e Track Slider HEA50714 2 e Connection Tube Bushing HEA507068 2 e Tie Wraps 2 The nitrogen gas shocks aid only in folding the unit These shocks must be removed with the unit on its side and in the folded position 1 Pull the Release Handle which is on the left rear of the unit and unfold the unit 2 Ifthe unit power cord is unplugged then plug in the power cord and then turn ON the unit 3 Atthe Control Console set the unit elevation to zero 4 With the elevation at zero shut OFF the unit and then unplug the AC power cord from the wall and the unit and set it aside 5 Remove four Phillips screws from the motor cover and lift off the motor cover 6 Fold the unit back up IMPORTANT Care must be taken to avoid damaging the unit or the floor before proceeding to the next step 7 With sufficient protective covering on the floor and the unit in the folded position tilt the unit over on its right side so that the Release Handle is exposed and easily accessible d NOTE THE UNIT MUST BE IN THE 1 FOLDED POSITION WITH SHOCKS AS em es FULLY EXTENDED BEFORE a Faa ATTEMPTING TO REMOVE SHOCKS ai 8 The shocks aid only in ease of folding the unit These shocks must be removed with the unit on its side in the folded position Be2. T m 57 ld a x E e M _ um m i a imn n B al Jm T E i i ee ii re a A w Ha I E aT Ps oe on n eu Dern E al as y E A E a a en om recte iom ji M ee a a a me e EN 2 ie Een E al Hn ine Pe ee A QUU domu ASSY INSTRUCTIONS KIT FT BUSHING 77650901 BUSHING REPLACEMENT CONTINUED 13 14 15 16 17 Rubber Stops In U Channels Bracket Remove the bolts 6mm nuts 13mm and bushings on both sides of incline pivoting brace Remove the retaining bolts 5mm and rubber stops at the ends of the U Channels Cut the tie wraps securing the Console Cable along side of the base frame Base Frame Slide the base frame forward just enough to allow replacement of Track Sliders Bushing Spacers and Connection Tube Bushings Install new kit components and re assemble in reverse order of removal Bushing Spacer ASSY INSTRUCTIONS KIT FT BUSHING 77650901
3. fore removing the shocks note that the rod end connects to the pivoting brace while the cylinder end connects to the main frame Remove the nuts 13mm at both ends of the shock and lift off the shock from the threaded mounting posts It may be necessary to apply some additional folding pressure to the unit to release each shock from its mountings 9 With the shocks removed and the Hardware n Cks hardware unit still on its right side pull the Release Handle and unfold the unit and then upright the unit ASSY INSTRUCTIONS KIT FT BUSHING 77650901 BUSHING REPLACEMENT CONTINUED 10 Remove the bolts and L Brackets from the bottom of the uprights then lower the uprights against the deck and disconnect the Console Wiring Harness Connector on the left side and then set the uprights aside L Brackets E 11 Using two pieces of wood blocks Unit Inverted on Supports 4 x4 x30 turn the unit upside af he aa down against the wooden blocksas __ J Elo X Y La shown X EFE pem RE J Note Make sure that treadmill is stable i on the supports R Supports 12 Remove the two screws securing the grounding strap m Ground Strap gt d s m ER 7X SI i is iw x a a oc bs re F Em i a F eg M E a x I oy uli na ba ar e i LM aa Fu Tin Poo Ec T ma Ss j m Ue ho M Bc un Pd m E ir Mu Ps d UE e al a m nh E a
Download Pdf Manuals
Related Search