LG W2261VP User's Manual
Contents
1. however moveable picture is not So the recommend resolution is 1920 x 1080 60Hz Troubleshooting Display image is incorrect O The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel Settings O The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Have you installed the display driver O Have you installed the e Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http www lge com O Do you see an e Make sure to check if the video card supports Unrecognized monitor Plug Play function Plug amp Play VESA DDC monitor found message Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Signal cable Power cord NOTE Specifications W2261VP 21 5 inches 54 6 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 54 6 cm 0 248 0 248 mm pixel pitch 30 83 kHz Automatic Analog Digital 56 75 Hz Automatic HDMI 56 61 Hz A2. 17 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display Using the Computer 1 Make sure to turn off the computer and product Connect the cable as below sketch map form to EY Connect DVI D Cable Connect D sub Cable PC Connect D sub Cable Mac Connect HDMI Cable NOTE m This is a simplified representation of the rear view m This rear view represents a general model your display may differ from the view as shown m User must use shielded signal interface cables D sub 15 pin cable DVI cable with ferrite cores to maintain standard compliance for the product E W2261VP W2261VG Headphone Earphone Input D sub DMI HDMI El TE O Signal Cable Varies according to model Wall outlet type AV equipment Set Top Box DVD Video A Video Game Console j ell 1 O o ro gt DVI D This feature is not available in all countries lt gt j gt PC Q aii gt MAC Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector Connecting the Display a W2361V W2361VG Headphone Earphone Input mm 1 Signal Cable ED Varies according to model Em
3. 4 cm 0 266 0 266 mm pixel pitch 30 83 kHz Automatic Analog Digital 56 75 Hz Automatic HDMI 56 61 Hz Automatic Separate TTL Positive Negative SOG Sync On Green Digital HDCP 15 pin D Sub Connector DVI D connector Digital 19 pin HDMI Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI Max Analog VESA 1920 x 1080 60 Hz Digital VESA 1920 x 1080 060 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B Digital HDMI DDC 2AB Analog Horizontal Freq Vertical Freq Input Form Signal Input On Mode 42 W Typ Sleep Mode lt 1W Off Mode lt 1W With Stand Without Stand Width 55 69 cm 21 93 inches 55 69 cm 21 93 inches Height 40 76 cm 16 05 inches 34 09 cm 13 42 inches Depth 19 32cm 7 61 inches 6 78cm 2 67 inches Net 4 5 kg 9 56 lbs Tilt 5 17 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Attached _ Detached O Wall outlet type a Information in this document is subject to change without notice Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Signal cable Power cord NOTE W2361VG 23 inches 58 4 cm Flat Panel
4. O hh Ll AV equipment Set Top Box DVD Video Wall outlet type F A Video Game Console Q rc n DVI D This feature is not available in all countries y j PC O o LN gt MAC Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector 2 Touch the power button on the front of panel to turn the power on When monitor power is turned on the e Power button Self Image Setting Function is executed automatically Only to the D sub signal cable input gt X La PROCESSING SELF IMAGE SETTING NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO SET Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution touch the AUTO SET function button to improve resolution Control Panel Functions Front Panel Controls m ES Cc 886 135 O1NY 3NI N3 4 Control Function 1 FUN Button Use this button to enter EZ ZOOMING 4 3 IN WIDE PHOTO EFFECT CINEMA MODE VOLUME TIME CONTROL items for more information refer to page A16 A1
5. a long time may cause damage to the screen and cause image burn Make sure to use a screen saver on the product Bum in and related problems are not covered by the warranty on this product Do not shock or scratch the front and sides of the screen with metallic objects Otherwise it may cause damage to the screen M ake sure the panel faces forward and hold it with both hands to move If you drop the product the damaged product can cause electric shock or fire Contact an authorized the service center for repair Avoid high temperatures and humidity Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over Spraying may cause electrical shock When cleaning the product unplug the power cord and scrub gently with a soft cloth to prevent scratching Do not clean with a wet cloth or spray water or other liquids directly onto the product An electric shock may occur Do not use chemicals such as benzene paint thinners or alcohol Spray water onto a soft cloth 2 to 4 times and use it to clean the front frame wipe in one direction only Too much moisture may cause staining On Repacking a Do not throw away the carton and packing matenals They make an ideal container in which to transport the unit When shipping the unit to an
6. resolution aanwe jeto o OEI NORMAL flO aisle SASS L To adjust screen color mode MONOCHROME e O CINEMA mone o __ Tofocusonthe moving picture selected VOLUME Toadustthevolme TIME CONTROL To mind user usingtime BRIGHTNESS letal astan o adjust the brightness contrast an PICTURE CONTRAST ejeje gamma of the screen Gamma LO LO lO BLACK LEVEL 6 Tosetoffsetlevel sa fe ele PRESET k Jejeje sok ejeje RD elele To costomize the color of the screen GREEN Jeljele BLUE Jeljele MM CI E lc mi TRACKING CLOCK PHASE SHARPNESS LANGUAGE ejeje OSD HORIZONTAL o POSITION venca e o Je WHITEBALANCE el To costomize the screen status for a MOVERSCAN 6 J user s operating environment ojojo meo POWERINDICATOR FACTORYRESET elele MOVIE e lele INTERNET ejej seh OOO FLATRON e F ENGINE NORMAL feje sotigs eremo STANDARD fe DEMO elel SPORTS O e Adjustable R DSUB Input only for D sub DVI Input D DVI Input gt only for HDMI Input H HDMI Input NOTE The order of icons may differ depending on the model A11 A19 On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu Press t
7. 50 1920 x 1080 Horizontal Freq kHz 31 468 31 469 37 500 37 879 46 875 48 363 60 123 67 500 63 981 79 976 65 290 67 500 Vertical Freq Hz HA Recommend Mode HDMI Timing Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz 1 480P 31 50 60 2 576P 31 25 50 3 720P 37 50 50 4 720P 45 00 60 5 1080i 28 12 50 6 1080i 33 9 60 T 1080P 56 25 50 8 1080P 67 50 60 Indicator On Mode Red Sleep Mode Flicker Off Mode Off Digitally yours saan La
8. 7 Use this button to enter or exit from the On Screen Display 2 MENU Button OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that these settings are not inadvertently changed To lock the OSD settings press and hold the MENU button for several seconds The message OSD LOCKED appears You can unlock the OSD settings at any time by pushing the MENU button for several seconds The message OSD UNLOCKED appears Control Panel Functions Control E A V Buttons VW Button JFENGINE A Button SOURCE AUTO SET Button PROCESSING AUTO IMAGE ADJUSTMENT 5 Power Button O Power Indicator Function Use these buttons to select or adjust functions in the On Screen Display For more information refer to page A18 A19 J ENGINE Use this button to make DSUB DVI or HDMI connector active This feature is used when two computers are connected to the display HDMI is optimized on the AV equipment Use this button to select an icon in the On Screen Display AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO SET button prior to entering the On Screen Display OSD This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is 1920 x 1080 Use this button to turn the display on or off Operate key up to Red
9. Active matrix TFT LCD Glare coating Visible diagonal size 58 4 cm 0 266 0 266 mm pixel pitch 30 83 kHz Automatic Analog Digital 56 75 Hz Automatic HDMI 56 61 Hz Automatic Separate TTL Positive Negative SOG Sync On Green Digital HDCP 15 pin D Sub Connector DVI D connector Digital 19 pin HDMI Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI Max Analog VESA 1920 x 1080 60 Hz Digital VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B Digital HDMI DDC 2AB Analog Horizontal Freq Vertical Freq Input Form Signal Input On Mode 42 W Typ Sleep Mode lt 1W Off Mode lt 1W With Stand Without Stand Width 55 69 cm 21 93 inches 55 69 cm 21 93 inches Height 40 76 cm 16 05 inches 34 09 cm 13 42 inches Depth 19 32 cm 7 61 inches 6 78cm 2 67 inches Net 4 5 kg 9 56 lbs Tilt 517 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached _ Detached O Attached Detached O Wall outlet type a Information in this document is subject to change without notice Preset Modes Resolution DSUB DVI Display Modes Resolution OONDOIBRWNM Timing 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 10
10. User s Guide W2361V W2261VP W2261VG W2361VG Make sure to read the Important Precautions before using the product Keep the User s Guide CD in an accessible place for future reference Sec the label attached on the product and give the information to your dealer when you ask for service Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a
11. advertising in the store The screen will be divided to show the standard mode on the left and video mode on the right so that the consumers can check the difference after applying the video mode HDMI input J ENGINE NES Wis abi SPORTS Select this when you watching general sports SPORTS J ENGINE env vie a ser USER You can manually adjust ACE or RCM only for a DSUB DVI input HUE or SATURATION only for HDMI input You can save or restore the adjusted value even when using a different environment To adjust the USER sub menu function press the AUTO SET Button l ACE Adaptive Clarity Enhancer Selects the clarity mode DSUB DVI input J ENGINE MENU W e A gt ser 580 Not applied 18 Weak clarity and luminosity contrast CY pu 8 2 Strong clarity and luminosity contrast ACE Zu ES 1 RCM Real Color Management Selects the color mode RCM A IO Not applied PSA Green enhance HDMI input Flesh tone JENGINE Meu VIE AE ser 0079 Color Enhance Fa HUE Adjust the screen hue SATURATION Adjust the screen saturation HUE O Je CS LO SATURATION Sn E 50 MENU Exit 7 Decrease Increase AUTO SET Select another sub menu Troubleshooting Check the following before calling for service No Image appears O Is the power cord of the Check and see if the power co
12. atic Analog Digital 56 75 Hz Automatic HDMI 56 61 Hz Automatic Separate TTL Positive Negative SOG Sync On Green Digital HDCP 15 pin D Sub Connector DVI D connector Digital 19 pin HDMI Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI Max Analog VESA 1920 x 1080 060 Hz Digital VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 060 Hz DDC 2B Digital HDMI DDC 2AB Analog Horizontal Freq Vertical Freq Input Form Signal Input On Mode 39 W Typ Sleep Mode lt 1 W Off Mode lt 1 W With Stand Without Stand Width 51 90 cm 20 43 inches 51 90 cm 20 43 inches Height 38 73 cm 15 24 inches 33 08 cm 13 02 inches Depth 19 32 cm 7 61 inches 6 34cm 2 50 inches Net 4 2 kg 9 26 lbs Tilt 5 17 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached _ Detached O Attached Detached O Wall outlet type a Information in this document is subject to change without notice Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Signal cable Power cord NOTE Specifications W2361V 23 inches 58 4 cm Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 58
13. decoration area around button even back side This Indicator lights up as red when the display is operating normally On Mode If the display is in Sleep Mode Energy Saving this indicator color changes to flicker On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments To make adjustments in the On Screen Display follow these steps MENU gt AV AUTO SET AW MENU 1 Press the MENU Button then the main menu of the OSD appears To access a control use the 4 or W Buttons When the icon you want becomes highlighted press the AUTO SET Button 3 Use the A W Buttons to adjust the image to the desired level Use the AUTO SET Button to select other sub menu items Push the MENU Button once to retum to the main menu to select another function Push the MENU Button twice to exit from the OSD On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus ELO BIN EI CJ ES o Toadustine
14. est upon or roll over the power cord and do not place the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER Block the bottom ventilation slots by placing the display on a bed sofa rug etc Place the display in a built in enclosure unless proper ventilation is provided Cover the openings with cloth or other material Place the display near or over a radiator or heat source Do not rub or strike the Active Matnx LCD with anything hard as this may scratch mar or damage the Active M atrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is charactenstic of the fixed resolution LCD panel Leaving a fixed image on the screen for
15. et your own green color levels MENU Exit z I Decrease BLUE Set your own blue color levels A Increase SET Select another sub menu On Screen Display OSD Selection and Adjustment Main menu TRACKING ua v a aS ser US VERTICAL B O PHASE BA Om O SHARPNESS nOD ME MENU Exit Y Decrease A Increase SET Select another sub menu Sub menu Description HORIZONTAL To move image left and right VERTICAL CLOCK PHASE SHARPNESS To move image up and down To minimize any vertical bars or stripes visible on the screen background The horizontal screen size will also change To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters To adjust the clearness of the screen Main menu Sub menu SETUP LANGUAGE ye OSD OSD POSITION POSITION HORIZONTAL Om H 50 O O E 50 WHITE T BALANCE OVERSCAN FACTORY RESET RTC MENU Exit Y Adjust A Adjust SET Select another sub menuPOWER INDICATOR FACTORY RESET On Screen Display OSD Selection and Adjustment Description To choose the language in which the control names are displayed To adjust position of the OSD window on the screen If the output of the video card is different the required specifications the colo
16. he MENU Button then the main menu of the OSD appears TRACKING SETUP Main Menu Es rer MENU 6 Exit Y 4 Adjust Decrease Increase SET Enter Select another sub menu Restart to select sub menu Button Tip Menu Name PICTURE MENUS WIE A ser 0 0 CONTRAST Sub menus Icons eee 14 70 GAMMA y __ NOTE OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Sub menu Description DSUB DVI input PICTURE BRIGHTNESS To adjust the brightness of the screen CONTRAST To adjust the contrast of the screen GAMMA Set your own gamma value 50 0 50 On the monitor high gamma values display whitish images and low gamma values display high contrast images BLACK LEVEL You can set the offset level If you select HIGH the screen will be bright and if you select LOW the screen will be dark only for HDMI input CONTRAST Omm ES Offset As the criteria for video signal it is the o p darkest screen the monitor can show BLACK LEVEL gt GAMMA Y ENU Exit Y Decrease Increase T Select another sub menu Ww m ae ae PRESET e SRGB Set the screen color to fit the SRGB standard color specification e 6500K Slightly reddish white cee oe e 9300K Slightly bluish white Sn 50 AA le RED Set your own red color levels el GREEN S
17. he screen e Press the AUTO SET button to automatically background vertical adjust your display image to the ideal setting bars or stripes are If the results are unsatisfactory decrease the visible vertical bars or stripes using the CLOCK icon in the on screen display O Any horizontal noise e Press the AUTO SET button to automatically appearing in any adjust your display image to the ideal setting image or characters If the results are unsatisfactory decrease the are not clearly horizontal bars using the PHASE icon in the on portrayed screen display e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color Important Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution lf the recommended resolution optimal resolution is not selected letters may be blurred and the screen may be dimmed truncated or biased Make sure to select the recommend resolution The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the video card performance In this case please ask to the computer or the video card manufacturer When HDMI interleaved signal 1920 x 1080i input static picture will be shaking
18. om lowers the display s resolution in single step increments Depressing the button Ol once lowers the resolution by one step while a second button press returns the resolution to the original display settings EZ ZOOMING This function is operated only if the forteManager is installed to PC ForteManager is not supported in HDMI input 4 3 IN WIDE To select the image size of the screen e WIDE Switch to full screen mode according to input image signal e 4 3 Change the image signal ratio into 4 3 O Main menu PHOTO EFFECT NORMAL GAUSSIAN BLUR SEPIA MONOCHROME MODE MODE VOLUME VOLUME TIME TIME CONTROL CONTROL RA Sub menu On Screen Display OSD Selection and Adjustment Description To select the color of the screen PHOTO EFFECT v A gt MENuU e gt NORMAL e NORMAL The PhotoEffect function is disabled e GAUSSIAN BLUR This option is to add the effect to the screen that the dark and sharp image becomes brighter and more blurred e SEPIA This option changes the screen to be Sepia tone The Sepia tone is brown color tone e MONOCHROME This option changed the screen to be Gray tone The screen image is displayed with just white black gray colors Photo Effect feature may not work in HDMI Input Photo effect operate at DSUB format It focuses better on the moving picture in selected area This function is operated only if the fo
19. other location repack it in its original maternal On Disposal The fluorescent lamp used in this product contains a small amount of mercury Do not dispose of this product with general household waste a Disposal of this product must be camed out in accordance to the regulations of your local authority Connecting the Display Connecting the stand 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the stand base into stand body in the correct direction as shown in the picture then tighten the screw which is attached to the stand base Stand Base Stand Body Screw 3 Once assembled take the monitor up carefully and face the front side Disassembling the stand 1 Place the monitor face down on the cushion or soft cloth 2 Loosen the screw which is attached to the stand base then take off the stand base from stand body Stand Body Stand Base Screw Important This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display 1 Adjust the position of the panel in various ways for maximum comfort Tilt Range 5
20. r level may deteriorate due to video signal distortion Using this function the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image Activate this function when white and black colors are present in the screen only for DSUB input To select the range of output image for DTV timing in HDMI input only for HDMI input Recommend overscan function to turn on when connect AV equipment If you set ON you enable the Response Time Control function If you set OFF you disable the Response Time Control function Use this function to set the power indicator on the front side of the monitor to ON or OFF If you set OFF it will go off If you set ON at any time the power indicator will automatically be turned on Restore all factory default settings except LANGUAGE Press the A W buttons to reset immediately If this does not improve the screen image restore the factory default settings If necessary perform the white balance function again This function will be enabled only when the input signal is an analog signal On Screen Display OSD Selection and Adjustment mm The OSD screen will appear when you touch the FUN button on the right bottom of the monitor DSUB DVI input CINEMA TIME MODE CONTROL nia EZ ZOOMING E HDMI input VOLUME TIME CONTROL gt OFF le Main menu Sub menu Description EZ ZOOMING EZ Zo
21. rd is connected display connected properly to the power outlet O Is the power indicator Press the Power button light on O Is the power indicator e If the display is in power saving mode try moving flickering the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC O Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again O Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen O Do you see OSD e You can secure the current control settings LOCKED when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect O Display Position is e Press the AUTO SET button to automatically incorrect adjust your display image to the ideal setting lf the results are unsatisfactory adjust the image position using the H position and V position icon in the on screen display O On t
22. rtemanager is installed to pc only for DSUB DVI input To adjust the volume of headphone Earphone only for HDMI input VOLUME w e AP SET menu 5 SE 50 Remind user using time by showing alarm OSD and flickering power LED Selection OFF 1HR 2HR On Screen Display OSD Selection and Adjustment mm The OSD screen will appear when you touch the fence button on the right bottom of the monitor Menu Name J ENGINE MENU W e A 2 ser y gt EI Sub menu Name gt MOVIE Main menu Sub menu Description FENCING menu WE AS MOVIE Select this when you are watching a video or movie DSUB DVI input JENGINE MENUS WEE AR INTERNET Select this when you are working on the document Word etc gt INTERNET HDMI input ACOs CAME Select this when you are playing a game S CCC gt GAME DSUB DVI input ENGINE MENUS WIE NORMAL Select this when you want to use the product in the most general using environment Normal mode is when f ENGINE is turned off gt NORMAL HDMI input STANDARD Select this when you want to use the original standard video E A In the General Standard mode the f ENGINE is turned off J ENGINE MENUS W e AB ser STANDARD O On Screen Display OSD Selection and Adjustment Main menu Sub menu Description DSUB DVI input F ENGINE menu VIE AR ser DEMO This is used for
23. shock or fire hazard Call your service technician for replacement As long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if the unit is tumed off Do not Open the Display There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer a Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always tum the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some intemal parts carry hazardous voltages a Do not add accessories that have not been designed for this display a When the display is to be left unattended for an extended period of time unplug it from the wall outlet a In the presence of thunder and lightning never touch the power cord and signal Cable because it can be very dangerous lt can cause electric shock Important Precautions On Installation Do not allow anything to r
24. utomatic Separate TTL Positive Negative SOG Sync On Green Digital HDCP 15 pin D Sub Connector DVI D connector Digital 19 pin HDMI Connector Input Form Analog 0 7 Vp p 75 ohm Digital HDMI Max Analog VESA 1920 x 1080 60 Hz Digital VESA 1920 x 1080 060 Hz Recommend VESA 1920 x 1080 060 Hz DDC 2B Digital HDMI DDC 2AB Analog Horizontal Freq Vertical Freq Input Form Signal Input On Mode 39 W Typ Sleep Mode lt 1 W Off Mode lt 1 W With Stand Without Stand Width 51 90 cm 20 43 inches 51 90 cm 20 43 inches Height 38 73 cm 15 24 inches 33 08 cm 13 02 inches Depth 19 32 cm 7 61 inches 6 34cm 2 50 inches Net 4 2 kg 9 26 lbs Tilt 517 AC 100 240V 50 60Hz 1 0A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Attached _ Detached O Wall outlet type a Information in this document is subject to change without notice Specifications Display Sync Input Video Input Resolution Plug amp Play Power Consumption Dimensions amp Weight Tilt Range Power Input Environmental Conditions Stand Base Signal cable Power cord NOTE W2261VG 21 5 inches 54 6 cm Flat Panel Active matrix TFT LCD Glare coating Visible diagonal size 54 6 cm 0 248 0 248 mm pixel pitch 30 83 kHz Autom
Download Pdf Manuals
Related Search