LevelOne GSW-1674T User's Manual
Contents
1. CD Rom with Web Management Utility and User s Guide If any item is found missing or damaged please contact your local reseller for replacement Installation The site where you install the hub stack may greatly affect its performance When installing consider the following pointers Install the LevelOne GSW 1674T 2474T in a fairly cool and dry place See Technical Specifications for the acceptable temperature and humidity operating ranges Install the Switch in a site free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight Leave at least 10cm of space at the front and rear of the hub for ventilation Install the Switch on a sturdy level surface that can support its weight or in an EIA standard size equipment rack For information on rack installation see the next section Rack Mounting When installing the Switch on a level surface attach the rubber feet to the bottom of each device The rubber feet cushion the hub and protect the hub case from scratching Rack Mounting The switch can be mounted in an EIA standard size 19 inch rack which can be placed in a wiring closet with other equipment Attach the mounting brackets at the switch s front panel one on each side and secure them with the provided screws Figure 1 Combine GSW 1674T 2474T with the provided screws Then use screws provided with the equipment rack to mount each switch in the rack2. Flow Control ID Speed Figure 19 Speed Disable This setting has six modes 100M Full 100M Half 10M Full 10M Half Auto and Disable for speed or port disable selections Flow Control 25 This setting determines whether or not GSW 1674T 2474T will be handling flow control Set FlowCtrl to Enable for avoiding data transfer overflow Or it sets to Disable there is either no flow control or other hardware software management When the port is set to forced mode then the flow control will automatically set to Disable QoS In some ports that need to have a high priority to manage the data transfer QoS should be change The default setting of all port QoS is high set the QoS to Normal where the ports that do not need to have a high priority of transferring data VLAN Settings Virtual Local Area Network Group individual ports into a small Virtual network of their own to be independent of the other ports To add a VLAN group press Add Group button the new VLAN configuration window will pop out you can fill in the description in order to describe this VLAN Group check on the port to be a member to this VLAN Group and press Apply button to execute the setting Figure 20 VLAN Group Settings 26 Once you want to modify the VLAN Group check on the ID parameter the ID VLAN configuration window will pop out 01 02 03 04 05 06 07 08 09 10 11 12 EE har ar Y vvv 13 14 15 16 a
3. PS M Figure 2 Mount the Switch in the rack Connecting Network Cable LevelOne GSW 1674T 2474T supports 1000Mbps Gigabit Ethernet that runs in Auto negotiation mode and 10Mbps Ethernet or 100Mbps Fast Ethernet that runs both in half and full duplex mode and 1000Mbps Gigabit Ethernet runs in full duplex mode using four pair of Category 5 Cable These RJ 45 ports are Auto MDI type port The Switch can auto transform to MDI II or MDI X type so you can just make an easy connection that without worrying if you are using a standard or crossover RJ45 cable AC Power LevelOne GSW 1674T 2474T used the AC power supply 100 240V AC 50 60 Hz The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan The switch s power supply will adjust to the local power source automatically and may be tumed on without having any or all LAN segment cables connected IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel rear panel and LED indicators of LevelOne GSW 1674T 2474T Front Panel The figure below shows the front panels of the Switch Figure 4 Front panel of GSW 2474T 24 port Gigabit Ethernet Switch LED Indicator Comprehensive LED indicators display the status of GSW 1674T 2474T and the network see the LED Indicators chapter below Gigabit Ethernet Ports Port 1 16 24 The Switch 16 24 Gigabit twisted pair ports supported auto negotiable 10 10
4. 16 Port 101100 000M Gigabit SW MAC Address 0012233445fe IP Address k 16 3 22 Subnet mask 255 285 0 0 Gateway 172 18 1 254 Settrapto 172216 2 3 240 System name Joe Test Location PM Joe Password Set Cancel Figure 11 Configuration Setting 18 Password Change You can use this Password Change when you need to change the password fill m the password needed in the dialog box and press Set button to proceed the password change immediately Original password New password Confirm password Set Cancel Figure 12 Password Change Firmware Upgrade When the device has a new function there will be a new firmware to update the device use this function to update Firmware Upgrade Device information Device IP 1721 6 2 22 Device Mac Upgrade setting Firmware Path Browse Password Upgrade State Start Figure 13 Web Access Double click the device in the Monitor List or select a device in the Monitor List and press this Web Access button to access the device in Web browser 19 Toolbar The toolbar in the Web Management Utility have four main tabs File View Options and Help In the File TAB there are Monitor Save Monitor Save As Monitor Load and Exit Monitor Save To record the setting of the Monitor List to the default when you open the Web Management Utility next time it will auto load the default recorded setting Monitor Save As To record
5. 50 60 Hz internal universal power supply 25 Watts Max for GSW 1674T 32Watts Max for GSW 2474T Operating 0 40 C Storage 10 70 C Humidity Operating 10 90 Storage 5 90 0210 mm WAXD FCC Class A CE Mark Class A VCCI Class A cUL UL60950 CB IEC60950 34 Performance Transmits Method Store and forward Filtering Address Table 4 8K entries per device for GSW 1674T 2474T Packet 10Mbps Ethernet 14 880 pps Filtering Forwarding Rate 00 Mbps Fast Ethernet 148 800 pps 1000Mbps Gigabit Ethernet 1 488 000 pps Transmits Method Store and forward RAM Buffer 272 400K bytes per device for GSW 1674T 2474T 35
6. 9 e Mre Top Figure 9 When the View Trap button is clicked a Trap Information window will pop out it will show the trap information including the Symbol Time Device IP and the Event occured Figure 10 The symbol represents the trap signal arise this symbol will disappear after you review and click on the event record Ki x S Tme Evert M 06 17 2003 11 0 17216322 16 Port 10 1 0071 GOOM Cegabt SVV 1 007 Login irrealid password fron 1 4 Ce Figure 10 Note In order to receive Trap information switch has to be configured with Trap IP and Trap Events in Web browser which are available in the Trap Setting Menu see Page 45 for detail Add Item To add a device to the Monitor List manually enter the IP Address of the device that you want to monitor Delete Item To delete the device in the Monitor List 17 Device Setting You can set the device by using the function key in the Device Setting Dialog box Configuration Setting In this Configuration Setting you can set the IP Address Subnet Mask Gateway Set Trap to Trap IP Address System name and Location Select the device in the Discovery list or Monitor List and press this button then the Configuration Setting window will pop out as Figure 10 after filling up the data that you want to change you must fill up the password and press the Set to process the data changed immediately Configuration setting x Product name
7. Ethernet is essential to coping with the network bottlenecks that frequently develop as computers and their busses get faster and more users use applications that generate more traffic Upgrading key components such as your backbone and servers to Gigabit Ethernet can greatly improve network response times as well as significantly speed up the traffic between your subnets Gigabit Ethernet enables fast optical fiber connections to support video conferencing complex imaging and similar data intensive applications Likewise since data transfers occur 10 times faster than Fast Ethernet servers outfitted with Gigabit Ethernet NIC s are able to perform 10 times the number of operations in the same amount of time In addition the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost effective method to take advantage of today and tomorrow s rapidly improving switching and routing internetworking technologies And with expected advances in the coming years in silicon technology and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded twisted pair UTP cabling outfitting your network with a powerful 1000 Mbps capable backbone server connection creates a flexible foundation for the next generation of network technology products Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performan
8. mm mM Figure 21 VLAN Settings Trunk Setting The Trunk function enables to cascade two devices with a double times bandwidth maximum up to 1 6Gbps in full duplex mode There are three selections in each group of trunk setting as follow Group 1 Selection 1 disable Selection 2 port 1 2 Selection 3 port 1 2 3 4 Group 2 Selection 1 disable Selection 2 port5 6 Selection 3 port 5 6 7 8 X305 NN Figure 22 Trunk Settings Be sure that the selected trunk setting port must connect to the device with a same VLAN group 27 Mirror Setting Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and or outgoing packet from one port of a network switch to another port where the packet can be studied It enables the manager to keep close track of switch performance and alter it if necessary Configuring the port mirroring by assigning a source port from which to copy all packets and a sniffer port where those packets will be sent The selection of the sniffer mode is as follow RX receive mode this mode will duplicate the data that send to the source and forward to the sniffer port ID 01 Sniffer Mode I H Sniffer Port 01 02 03 04 05 06 07 08 09 10 11 12 I CEE E E M M EM EM E E E Source Port 13 14 15 16 Figure 23 Device Status Click on the Status to present the device status on this screen it will show the System Status P
9. sse 5 Features e 5 Unpacking and Installation essen 7 Unpacking rn rere eee RR RAE TESTS 7 Installation oi Deere Ree eod 7 Rack Mounting ciones 8 Connecting Network Cable sse 9 AG POW nio pee bo EUR Or CU og et ne e RS 9 Identifying External Components essere 10 Front Patel 52m oaend enia e qo etre 10 Rear Palin 11 Understanding LED Indicators sese 12 Power and System LEDS nsore 12 Ports 1 16 24 Status LEDS sese 13 Configuration eee me HR e ERE FREE 14 Installing the Web Management Utility ssssss 14 Discovery List oe SERERE a e e OR tu 15 Monitor Dist ooo acri nb dii S Roter 16 Device Setting s xo acc hohe RE id S HERE 18 gil 20 Configuring GSW 1674T 2474T sse 21 Login siete id 21 Nnm 23 Configuring Setup Setting 24 Port Settings i2 E O OS 24 VLAN Settings Virtual Local Area Network 26 Trunk Sene xcci p m eO URS 27 Mirror Setting usd eee deo OR NI e ett ns 28 DEVICE Status Az 28 Sata aa ds 29 System Setting ci He e ede 30 Trap Setting eese eee eee e Rees 30 Set Password idco DRE ete eine nte 31 Backup Setting 32 Reset Sette taa ed dee tad aime sane en 33 TOO da o qtiam aeneis 33 Technical Specifications secsi isie 34 ABOUT THIS GUIDE Congratulations on your purchase
10. the setting of the Monitor List in appointed filename and file path Monitor Load To manually load the setting file of the Monitor List Exit To exit the Web Management Utility In the View TAB there are view log and clear log function this function will help you to show trap setting View Log To show the event of the Web Management Utility and the device Clear Log to clear the log In the Option TAB there are Refresh Time function this function helps you to refresh the time of monitoring the device Choose 15 secs 30 secs 1 min 2 min and 5 min to select the time of monitoring In the Help TAB there is About function it will show out the version of the Web Management Utility 20 Configuring LevelOne GSW 1674T 2474T LevelOne GSW 1674T 2474T 16 24 port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch has a Web GUI interface for smart switch configuration The Switch can be configured through the Web Browser A network administrator can manage control and monitor the switch from the local LAN This section indicates how to configure the Switch to enable its smart functions including Port Setting Speed Disable Duplex mode Flow Control and Port base QoS Virtual LAN Group setting VLAN Trunking Port Mirroring System Setting Device status and Statistic 09009606 Login Before you configure this device note that when the Web Smart Switch is configured through an Ethernet connectio
11. transmission capacity The switch acts as a high speed selective bridge between the individual segments The switch without interfering with any other segments automatically forwards traffic that needs to go from one segment to another By doing this the total network capacity is multiplied while still maintaining the same network cabling and adapter cards Switching LAN technology is a marked improvement over the previous generation of network bridges which were characterized by higher latencies Routers have also been used to segment local area networks but the cost of a router the setup and maintenance required make routers relatively impractical Today switches are an ideal solution to most kinds of local area network congestion problems VLAN Virtual Local Area Network A VLAN is a group of end stations that are not constrained by their physical location and can communicate as if a common broadcast domain a LAN The primary utility of using VLAN is to reduce latency and need for routers using faster switching instead Other VLAN utility includes Security Security is increased with the reduction of opportunity in eavesdropping on a broadcast network because data will be switched to only those confidential users within the VLAN Cost Reduction VLANS can be used to create multiple broadcast domains thus eliminating the need of expensive routers Port based or port group VLAN is the common method of implementing a VLAN
12. 0 lt 0 7e EAETEJEH m El EE NH LevelOne GSW 1674T GSW 2474T 16 24 Port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch User s Guide FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense CE Mark Warning This 1s a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VCCI Warning This is a product of VCCI Class A Compliance tE COPEL FRE ZE SERE E MESES VCC ORE ES REE RR ETT IJDEESJERETEE TALER BER SMITLEMBDVET ox weg Bub RE ET S LUOBRANSIEBHVET UL Warning a Elevated Operating Ambient Temperature If installed in a closed or multi unit rack assembly the operating ambient temperat
13. 0 1000Mbps and auto MDI MDIX crossover detection function this function gives true plug and play capability just need to plug in the network cable to the hub directly and don t care if the end node is NIC Network Interface Card or switch and hub These ports can operate in half duplex mode for 10 100Mbps and full duplex mode for 10 100 1000Mbps Note When the port was set to Forced Mode the Auto MDI MDIX will be disabled 10 Rear Panel Power Switcr Reset Power Connector Figure 5 Rear panel of the Switch Power Switch This is a switch where you can control to enable or disable the power AC Power Connector This is a three pronged connector that supports the power cord Plug in the female connector of the provided power cord into this connector and the male into a power outlet Supported input voltages range from 100 240V AC at 50 60Hz Reset The Reset button is to reset all the setting back to the factory default Note Be sure that you recorded the setting of your device else all the setting will be erased when pressing the Reset button UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback and helps monitor and troubleshoot when needed 1 one L et 2 LI LI Gigabit Ethernet M GSW 1674T 16 Pol 7 E E WM GSW 2474T 24 Port Gigabit Ethernet Figure 7 LED indicators of GSW 2474T Power and System LEDs Power Ind
14. and is the one supplied in GSW 1674T 2474T Features 16 24x10 100 1000Mbps Auto negotiation Gigabit Ethernet ports All RJ45 ports support auto MDI MDIX so there is no need to use cross over cables or an up link port Full half duplex transfer mode for 10 100Mbps port Full duplex transfer mode for Gigabit port Wire speed reception and transmission 999 Store and Forward switching scheme capability to support rate adaptation and ensure data integrity Up to 4K 8K for GSW 1674T 2474T unicast addresses entities per device self learning and table aging 44999 49905050 272 400K Bytes packet buffer for GSW 1674T 2474T Supports IEEE 802 3x flow control for full duplex mode ports Supports port base VLAN Supports port base QoS Supports Trunking Supports Port mirroring Supports Port setting for Speed Disable Flow control Easy configuration via WEB Browser Easy setting via Web Management Utility Standard 19 Rack mount size UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for LevelOne GSW 1674T 2474T Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents The carton should contain the following items One 24 Port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch One AC power cord suitable for your area s electrical power connections Four rubber feet to be used for shock cushioning Screws and two mounting brackets
15. ce networks A number of high speed LAN technologies have been proposed to provide greater bandwidth and improve client server response times Among them 100BASE T Fast Ethernet provides a non disruptive smooth evolution from the current 10BASE T technology The non disruptive and smooth evolution nature and the dominating potential market base virtually guarantees cost effective and high performance Fast Ethernet solutions 100Mbps Fast Ethernet is a standard specified by the IEEE 802 3 LAN committee It is an extension of the 10Mbps Ethernet standard with the ability to transmit and receive data at 100Mbps while maintaining the CSMA CD Ethernet protocol Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments it provides a straightforward upgrade and takes advantage of the existing investment in hardware software and personnel training Switching Technology Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments Switching is a cost effective way of increasing the total network capacity available to users on a local area network A switch increases capacity and decreases network loading by dividing a local area network into different segments which don t compete with each other for network
16. he version of the Utility protocol Product Name Shows the device product name System Name Shows the appointed device system name Location Shows where the device is located Trap IP Shows the IP where the Trap to be sent Subnet Mask Shows the Subnet Mask set of the device Gateway Shows the Gateway set of the device Monitor List All the Web Smart Device in the Monitor List can be monitored you can also receive the trap and show the status of the device System word definitions in the Monitor List eo S Shows the system symbol of the Web Smart device E represent for device system is not alive IP Address Shows the current IP address of the device MAC Address Shows the device MAC Address Protocol version Shows the version of the Utility protocol Product Name Shows the device product name System Name Shows the appointed device system name Location Shows where the device is located Trap IP Shows the IP where the Trap to be sent Subnet Mask Shows the Subnet Mask set of the device Gateway Shows the Gateway set of the device 16 View Trap The Trap function can receive the events that happen from the Web Management Switch in the Monitor List There is a light indicator behind the View Trap button when the light indicates in green it means that there is no trap transmitted and else when it indicates in red it means that there is new trap transmitted this is to remind us to view the trap Figure
17. icator On When the Power LED lights on GSW 1674T 2474T is receiving power Off When the Power turns off or the power cord has improper connection SYSTEM Management Indicator Blinking When the CPU is working the System LED is blinking On Off The CPU is not working 12 Ports 1 16 24 Status LEDs Link ACT Link Activity On When the Link ACT LED lights on the respective port is successfully connected to an Ethernet network Blinking When the Link ACT LED is blinking the port is transmitting or receiving data on the Ethernet network Off No link 1000Mbps On When the 1000Mbps LED lights on the respective port is connected to a 1000Mbps Gigabit Ethernet network Off When the respective port is connected to a 10Mbps Ethernet or 100Mbps Fast Ethernet network 100Mbps On When the 100Mbps LED lights on the respective port is connected to a 100Mbps Fast Ethernet network Off When the respective port is connected to a 10Mbps Ethernet or 1000Mbps Gigabit Ethernet network 13 CONFIGURATION Through the Web Browser you can configure GSW 1674T 2474T such as VLAN Trunking QoS etc With the attached Web Management Utility you can easily discover all the Web Management Switch assign the IP Address changing the password and upgrading the new firmware Installing the Web Management Utility The following gives instructions gu
18. iding you through the installations of the Web Management utility 1 Insert the Utility CD in the CD Rom Drive 2 From the Start menu on the Windows desktop choose Run 3 In the Run dialog box type D Web Management Utility setup exe D depends where your CD Rom drive is located and click OK 4 Follow the on screen instructions to install the utility 5 Upon completion go to Program Files gt web management utility and execute the Web Management utility Figure 6 14 Option Help Qescovery Lit Unc der Passes msecavese roanavane Syetea ane uses lt gt Add to mentor tet Y SP Address MAC Address Protocol Version frodihene System Name Loci Monitor List Figure 8 Web Management Utility The Web Management Utility was divided into four parts Discovery List Monitor List Device Setting and Toolbar function for details instruction follow the below section Discovery List This is the list where you can discover all the Web management devices in the entire network By pressing the Discovery button you can list all the Web Management devices in the discovery list Double click or press the Add to monitor list button to select a device from the Discovery List to the Monitor List 15 System word definitions in the Discovery List MAC Address Shows the device MAC Address IP Address Shows the current IP address of the device Protocol version Shows t
19. igure 17 Click on the setup item that you want to configure There are eleven options Port Settings VLAN Settings Trunk Setting Mirror Setting Device Status Statistic System Settings Trap Setting Password Setting Backup Setting and Reset Setting as shown in the Main Menu screen 23 Setup m Port m VLAN Trunk m Mirror Maintenance m Status m Statistics m System m Trap m Password Backup Setting m Reset Setting Logout Figure 17 Setup menu Configuring Setup Setting Find that there are four items including Port Settings VLAN Settings Trunk Settings and Mirror Settings in Setup menu Port Settings In Port Settings menu Figure 18 this page will show each port s status press the ID parameter to set each port s Speed Flow Control QoS priority and Link Status When you need to renew the posted information press the Refresh button The Link Status in the screen will show the connection speed and duplex mode else this dialog box will show down when the port is disconnected 24 High 0 _ High Down g i e High En High Down pen Down 12 JEnable High Down High Down 3 Figure 18 Port Setting To change the port setting click on the ID parameter to enter to the selected port to configure its Speed Disable Flow control and QoS setting Please be aware that speed must set as same as link parnter Otherwise packet loss or link error might occur
20. n make sure the manager PC must be set on same the IP network For example when the default network address of the default IP address of the Web Smart Switch is 192 168 0 1 then the manager PC should be set at 192 168 0 x where x is a number between 2 and 254 and the default subnet mask is 255 255 255 0 Open Internet Explorer 5 0 or above Web browser Enter IP address http 192 168 0 1 the factory default IP address setting to the address location Address Figure 14 21 Or through the Web Management Utility you do not need to remember the IP Address select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser When the following dialog page appears remain enter the default password admin and press Login to enter the main configuration window System Name Location Name IP Address 192 168 0 1 MAC ddress 00 11 22 33 44 55 password Figure 15 After entering the password the main page comes up the screen will display the device status 22 e 90d sued IA Med Dinar gal Sist onfiguration one Setup mn Port sm VLAN Trunk m Minor Maintenance Satus a Statistics System Top m Password m Backup Setting Reset Setting Logout Link Flow Control Control aos Figure 16 Device Status Setup Menu When the main page appears find the Setup menu in the left side of the screen F
21. normal receive error b Port Events mj abnormal transmit error Figure 27 Trap Setting System Events Monitoring the system s trap Device Bootup a trap when booting up the system Illegal Login a trap when there is using a wrong password login and it will record from where the IP to be login Twisted Pair Port Events Monitoring the copper port status Abnormal Receive Error a trap when there are receive data error in copper port Abnormal Transmit Error a trap when there are transmit data error in copper port Abnormal 50 error packet count within 10 seconds Set Password Password is the invaluable tool for the manager to secure Web Management Switch use this function to change the password 31 If you forget the password press the Reset button in the rear panel of GSW 1674T 2474T the current setting includes VLAN Port Setting etc will be lost and the Switch will restore to the default setting The maximum length is 20 and is case sensitive Old Password New Password PRe type New Password Figure 28 Set Password Backup Setting The backup tools help you to backup the current setting of GSW 1674T 2474T Once you need to backup the setting press the Backup button to save the setting To restore a current setting file to the device you must specify the backup file and press Restore button to proceed the setting of the recorded file Please be aware that the device
22. of LevelOne GSW 1674T 2474T 16 24 Port 10 100 1000 Mbps Gigabit Ethernet Web Smart Switch This device integrates 1000Mbps Gigabit Ethernet 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package Purpose This guide discusses how to install your 16 24 port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch Terms Usage In this guide the term Switch first letter upper case refers to your LevelOne 16 24 port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch and switch first letter lower case refers to other Ethernet switches INTRODUCTION This chapter describes the features of Levelone GSW 1674T 2474T 16 24 port 10 100 1000 Mbps Gigabit Ethernet Web Smart Switch and some background information about Ethernet Fast Ethernet Gigabit Ethernet switching technology Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802 3 Ethernet utilizing the same packet structure format and support for CSMA CD protocol full duplex flow control and management objects but with a tenfold increase in theoretical throughput over 100 Mbps Fast Ethernet and a hundredfold increase over 10 Mbps Ethernet Since it is compatible with all 10 Mbps and 100 Mbps Ethernet environments Gigabit Ethernet provides a straightforward upgrade without wasting a company s existing investment in hardware software and trained personnel The increased speed and extra bandwidth offered by Gigabit
23. ort Status VLAN Status Trunk Status and Mirror Status Press Refresh when you need to renew the posted information 28 Statistic The Statistic Menu screen will show the status of each port packet count io Txok Rxok TxError RxError p Txok r Figure 24 Statistic For Detail packet information click on the ID parameter in Figure 24 Packets Bytes High Priority Packets 4014 Low Priority Packets 156209 Broadcast 7 Mutant 64 ytes 65 127 Byes Dytes 2 Bytes 512 1023 Bytes 1024 Bytes Comvescers NFO Drops 29 System Setting The System Setting includes the System name Location name Login Timeout IP Address Subnet Mask and Gateway Through the Web Management Utility you can easily recognize the device by using the System Name and the Location Name The Login Timeout is to set the idle time out for security issue when there is no action in running the Web Smart Utility and the time is up you must re login to Web Smart Utility before you set the Utility Fill up the IP Address Subnet Mask and Gateway for the device System Name IDDC Location Name G 30 minute Do od 3 30 minutes Figure 26 Trap Setting The Trap Setting enables the device to monitor the Trap through the Web Management Utility set the Trap IP Address of the manager where the trap to be sent 30 or 15 To EN sekten F device bootup 2 illegal login b Twisted Pair fd ab
24. ure of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the manufacturer s maximum rated ambient temperature Tmra b Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised c Mechanical Loading mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading d Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on over current protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern e Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips Ver 1 00 TABLE OF CONTENT About This Guide diede ede Patet 1 lap EET 1 Terms U sage ii nin hei ee in ox 1 Intr ducti 4 52 ors tees Sass Salat apes RR 2 Gigabit Ethernet Technology sse 2 Fast Ethernet Technology sss 3 Switching Technology seen 4 VLAN Virtual Local Area Network
25. will reboot after config restore successfully Backup Backup current setting to file Bed Restore saved setting from file Figure 29 Backup Setting 32 Note when restoring a recorded file the current password will not be erased Reset Setting The Factory Reset button helps you to reset the device back to the default setting from the factory Be aware that the entire configuration will be reset the IP address of the device will be set to default setting 192 168 0 1 Please be aware that all configuration will reset to default value Figure 30 Reset Setting Logout When press this function the web configuration will go back to first Login page System Name Joe Test Location Name PM Joe IP Address AO az MAC Address 00 12 23 34 45 fe Password Figure 31 Logout 33 TECHNICAL SPECIFICATIONS Standards IEEE 802 3 IOBASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab 1000BASE T Gigabit Ethernet IEEE 802 3x Full Duplex Flow Control Protocol CSMA CD Data Transfer Rate Ethernet 10Mbps half duplex 20Mbps full duplex Fast Ethernet 100Mbps half duplex 200Mbps full duplex Gigabit Ethernet 2000Mbps full duplex Network Cables 10BASET 2 pair UTP Cat 3 4 5 up to 100m 100BASE TX 2 pair UTP Cat 5 up to 100m 1000BASE T 4 pair UTP Cat 5 up to 100m Number of Ports 16 24 x 10 100 1000Mbps Auto MDIX RJ 45 ports Physical and Environmental 100 240V AC
Download Pdf Manuals
Related Search