Home

Lenovo Laptop S200 User's Manual

1. When installing Insert the notched end of the DIMM into the socket Push the DIMM firmly and pivot it until it snaps into the place Make sure that it is firmly fixed in the slot and difficult to be moved 39 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 40 1050 PCI Express Mini Card for wireless LAN WAN For access remove these FRUs in order 1010 Battery pack on page 34 Figure 5 Removal steps of PCI Express Mini Card for wireless LAN WAN Disconnect the two wireless LAN cables H and then remove the screws A In step El unplug the jacks by using the removal tool antenna RF connector P N 08K7159 or pick up the connectors with your fingers and gently unplug them in the direction shown by arrows Notes wireless LAN card has 2 cables in step fj wireless LAN card in some models may have 3 cables in step D Step Screw quantity Color Torque H M2 x 5 mm flat head nylok coated 2 Black 1 5 kgfem Lenovo IdeaPad 5200 5206 Figure 5 Removal steps of PCI Express Mini Card for wireless LAN WAN continued Remove the card in the direction shown by arrow Efl When installing In models with a wireless LAN card that has two antenna connectors plug the black cable 1st MAIN into the jack labeled 1 and the white cable 2nd AUX into jack labeled 2 on the card In models with a wireless LAN card that has three antenna connectors plug the black cable 1
2. Press any key on the keyboard Also in the following event the computer automatically returns from sleep standby state and resumes the operation The time set on the resume timer elapses Note The computer does not accept any input immediately after it enters sleep standby state Wait a few seconds before taking any action to reenter operation mode 25 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Hibernation state In hibernation state the following occurs The system status RAM VRAM and setup data are stored on the hard disk The system is powered off To cause the computer to enter hibernation state follow the steps below If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation state perform that action Closing the lid Pressing the power button Also the computer goes into hibernation state automatically in either of the following conditions Ifa hibernation time has been set on the timer and if the user does not do any operation with the keyboard the hard disk drive the parallel connector or the diskette drive within that time Ifthe timer conditions are satisfied in suspend mode When the power is turned on the computer returns from hibernation state and resumes operation The hibernation file in the boot record on the hard disk drive is read and system status is restored
3. on page 67 2 Keyboard see Keyboard on page 69 3 WOODY IO BD ASSY 5200 90200285 N 3 WOODY IO BD 5206 90200285 N 4 WINNIE Upper Case Black Ccover_Grey S200 90200250 N 4 WINNIE Upper Case Black S206 90200250 N 5 WINNIE MB N2800 MB N2800 Group 200 90000090 N 5 WINNIE MB N2600 MB N2600 Group 200 90000089 N 5 WOODY MB C50 WO WWAN S206 90000094 N 5 WOODY MB C60 WO WWAN S206 90000093 N 6 3G WCDMA Ericsson Ericsson F5321gw HSPA 20200034 N Qual bands WWAN card 6 3G WCDMA Huawei Huawei EM820w HSPA 850 11012850 N 900 1900 2100MHz 6 3G EVDO Huawei Huawei EM660 EVDO GPS 11012299 N WWAN card 6 3G EVDO Sierra wireless Sierra MC8355 GOBI3000 20200163 N dualmode WWAN card 6 3G TD SCDMA TengChuang Leadcoretech TD SCDMA 11012849 N LC5740 mini card 6 3G AT amp T LTE Sierra wireless Sierra MC7700 AT amp T LTE 20200164 N module 7 WLAN card WiFi 1x2 BGN WiMAX Intel 6150NX 20002484 N MOW M PCIE NB HMC WLAN card LI S200 only 7 WLAN card WiFi 1x2 BGN WiMAX Intel 6150NX BSB 20002543 N M PCIE NB HMC WLAN card LI S200 only 7 WLAN card WiFi 1x2 BGN Intel 1000N MOW M PCIE 20002329 N NB HMC WLAN card S200 only 7 WLAN card WiFi 2x2 BGN Intel 2200N MOW M PCIE 20200048 N NB HMC WLAN card S200 only 7 WLAN card WiFi 1x1 BGN CyberTan Cbt RT3090 20002515 N MOW M PCIE NB HMC WLAN card 7 WLAN card WiFi 1x1 BGN Liteon AR9285 HB95 BGN 20002357 N MOW NB WLAN card IN 7 WLAN
4. WINNIE TP Cable ASSY S200 90200268 e j WINNIE TP Cable S206 90200268 Note Italicized letters in parentheses are references to the exploded view in Overall on page 71 73 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 74 AC adapters Table 8 Parts list 3 pin AC adapters FRU 40W Brazil PA 1400 12LB adapter Only Brazil local buy 40W Delta ADP 40NH B20V2A adapter 40W Liteon PA 1400 12LC 20V2A adapter 40W HIPRO LN A0403A3C 20V2A adapter P N 36001715 36001648 36001653 36001672 CRU ID ZZZI Lenovo IdeaPad S200 S206 Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region Table 9 Parts list 3 pin power cords Region P N CRU ID CCC 145000600 LINETEK PC323 RVV300 300 LS15 1m Argentina 145000599 e LINETEK LS15 H03VV F LP39 1m Danmark 145000598 e LINETEK LS15 HO3VV F LP 38 1m Switzerland 145000597 e LINETEK LS15 H03VV F LP 37 1m Brazil 145000596 e LINETEK LS15 H03VV F LP26A 1m Israel 145000595 e LINETEK LS15 H03VV F LP 41 1m UL 145000594 e LINETEK LP 30B SPT 2 LS15 1m UK 145000593 e LINETEK LP 61L HO3VV F LS15 1m Indian 145000592 e LINETEK PE 361 HO5VV F LS15 1m Italy 145000591 e LINETEK LS15 H03VV F PE 336 1m Korea 145000590 e LINETEK LS15 H05VV F LP E04A 1m Australia 145000589 e LINETEK LS15 HO3VV F LP 23A 1m Taiwan 145000588 e LINETEK LS15 VCTF LP 53 1m Japan 145000587
5. e LINETEK LS15 VCTF LP 54 1m Africa 145000586 e LINETEK LS15 H03VV F PE 364 1m CE 145000585 e LINETEK LP 34 H03VV F LS15 1m CCC 145000568 Longwell LSG 31 RVV300 300 LS 18 1m Argentina 145000567 Longwell LP 24 H03VV F LS 18 1m Danmark 145000566 Longwell LP 40 HO3VV F LS 18 1m Switzerland 145000565 Longwell LP 37 H03VV F LS 18 1m 75 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 76 Table 9 Parts list 3 pin power cords continued Region Brazil Longwell LP 46 H03VV F LS 18 1m Israel Longwell LP 41 HO3VV F LS 18 1m UL Longwell LP 30B SPT 2 18AWG LS 18 1m UK e Longwell LP 61L HO3VV F LS 18 1m Indian Longwell LP 67 BIS LS 18 1m Italy Longwell LP 22 HO3VV F LS 18 1m Korea Longwell LP 486 KTLH03VV F LS 5 1m Australia Longwell LP 23A LFC 3R LS 18 1m Taiwan Longwell LP 71 VCTF LS 33 1m Japan Longwell LP 54 VCTF LS 18 1m Africa Longwell LP 39 H03VV F LS 18 1m CE Longwell LP 34A H03VV F LS 18 1m CCC e VOLEX GB10S3 RVV 300 500 VAC5S 1m UL e Volex US1553 SPT 2 VAC5S 1m Indian e VOLEX IA6A3 IS694 VAC5S 1m Italy e VOLEX IT10S3 HO3VV F VAC5S 1m Danmark e VOLEX MP233D H03VV F VAC5S 1m Korea e VOLEX M2511 KETI IEC VAC5S 1m Australia e VOLEX AU1053 H03VV F VAC5S 1m Taiwan e VOLEX TWI5CS3 VCTF VAC5S 1m Japan e VOLEX VAC5S VCTF M755 1m Argentina VOLEX VA2073 H03VV F VAC5S 1m P N 145000564 145000563 145000562 145000561 1
6. Remove the dummy card in the direction shown by arrows El 36 Lenovo IdeaPad 200 S206 1030 Hard disk drive For access remove these FRUs in order 1010 Battery pack on page 34 r Attention Do not drop the hard disk drive or apply any physical shock to it The hard disk drive is sensitive to physical shock Improper handling can cause damages and permanent loss of data Before removing the drive suggest the customer to backup all the information on it if possible Never remove the drive while the system is operating or is in suspend mode d Figure 3 Removal steps of hard disk drive Remove the frame fixing screws Efl Pull the HDD bracket in the direction shown by arrow EJ Step Screw quantity Color Torque H M2 x 3 mm flat head nylok coated 4 Silver 1 5 kgfcm 37 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual Figure 3 Removal steps of hard disk drive continued Take out the hard disk drive secured in a metal frame in the direction shown by arrows El When installing Make sure that the HDD connector is attached firmly 38 Lenovo IdeaPad 5200 5206 1040 DIMM For access remove these FRUs in order 1010 Battery pack on page 34 Figure 4 Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the direction shown by arrows H and then unplug the DIMM in the direction shown by arrow PJ
7. has a current backup of the data before performing this action Attention The drive startup sequence in the computer you are servicing may have been changed Be extremely careful during write operations such as copying saving or formatting If you select an incorrect drive data or programs can be overwritten Important notice for replacing a system board Some components mounted on a system board are very sensitive Improper handling can cause damage to those components and may cause a system malfunction Attention When handling a system board Do not drop the system board or apply any excessive force to it Avoid rough handling of any kind Avoid bending the system board and hard pushing to prevent cracking at each BGA Ball Grid Array chipset 17 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs RoHS The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive 2002 95 EC is a European Union legal requirement affecting the global electronics industry RoHS requirements must be implemented on Lenovo products placed on the market after June 2006 Products on the market before June 2006 are not required to have RoHS compliant parts If the original FRU parts are non compliant replacement parts can also be non compliant In all cases if the original FRU parts are RoHS compliant the replacement part must also be RoHS compliant Not
8. of the total power remains under this condition the battery pack can charge to 100 of its capacity This protects the battery pack from being overcharged or from having a shortened life To check your battery move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment but do not click it and the percentage of battery power remaining is displayed To get detailed information about the battery double click the Power Meter icon Note If the battery pack becomes hot it may not be able to be charged Remove it from the computer and leave it at room temperature for a while After it cools down reinstall and recharge it To check the battery pack follow the steps below 1 Turn off the computer 2 Remove the battery pack and measure the voltage between battery terminals 1 and 7 See the following figure Terminal Voltage V DC 1 0 to 14 7 Ground 3 If the voltage is less than 11 0 V DC the battery pack has been discharged Note Recharging will be continued for at least 3 hours even though the indicator does not light on If the voltage is still less than 11 0 V DC after recharging replace the battery 4 If the voltage is more than 11 0 V DC measure the resistance between battery terminals 5 and 7 The resistance must be 4 to 30 KQ If the resistance is not correct replace the battery pack If the resistance is correct replace the
9. r Sonderm ll beachten Beim Ersetzen der Bereitschafts oder Systembatterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren mop Nyaa Man MIO NINAN MID IDAN DINO p525 yx OMITA Y SW IN UND AMIN PIN WIND ANN TOP IDIOT AN PIVI v AMN INP IN 055 V DIAM PAIN DNM mpnn n DN WINI DPIN VIA WINN NINDI PA VII DIY DION NI NINDI UVP V ANNA MINOR 5v MININA IN nns DIZAY Alcune batterie di riserva contengono una piccola quantita di nichel e cadmio Non smontarle ricaricarle gettarle nel fuoco o nell acqua n cortocircuitarle Smaltirle secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria dell RTC real time clock o la batteria di supporto utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa FTWANYT ITORLIIVEOZITA LAN FR VARFENTWS DORE V X3 LEBST AYTI DRA IH RETIRO SO RSE EY a KSWAT EIR UTTDRW CS REV AY TY ABRES S pilye BRROFBNTA ES TI REV BOZA Y e VARIA YT erer Letz Bok Ay FY REED Ny TY BH KLEY BRLIVFTELLRDYET Algunas bater as de reserva contienen una peque a cantidad de n quel y cadmio No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s
10. 17 Important information about replacing RoHS compliant FRUS en 18 General checkout What to do first Power system checkout Checking the AC adapter Checking operational charging Checking the battery pack Related service information 23 Restoring the factory contents by using Recovery Disc Set Start Recovery Disc one disc Operating System Recovery Disc one o or more discs e eie ice tb cease 23 Applications and Drivers Recovery Disc one or more discs Supplemental Recovery Disc Passwords Power on password Hard disk password Supervisor password Power management Screen blank state Sleep standby state Hibernation state Lenovo IdeaPad S200 S206 Specifications 27 Status indicators Fn key combinations Hotkeys FRU replacement notices Screw notices Removing and replacing an FRU 1010 Battery pack 1020 Dummy card 1030 Hard disk drive CTT 1050 PCI Express Mini Card for wireless LAN WAN 1060 3G Card 42 1070 Keyboard 43 1080 System board 45 1090 LCD unit 1100 Fan assembly and Heat Sink assembly eere etn 50 1110 Base cover speakers and power assemblw sse 52 1120 LCD front bezel 55 1130 LCD panel LCD cable and hinges 56 1140 Integrated camera Locations Front view Right side view Bottom and Left side view Parts list 6
11. 7mm 320G HDD Hard disk drive 320G 7200rpm Seagate ST320LT007 7200RPM 7MM 320G HDD Hard disk drive 500G 7200rpm HTS725050A7E630 7 2k RPM 7MM 500G HDD Hard disk drive 32G SSD Samsung PM830 32G mSATA SSD Hard disk drive 32G SSD Sandisk mSATA X100 32G WINNIE Speaker W Cable ASSY 5200 WINNIE Speaker W Cable S206 DDR3 1600 2GB Hynix HMT325S6CFR8C PB DDR3 1600 2GB DDR3 1600 2GB Micron MT8KTF25664HZ 1G6M1 DDR3 1600 2GB DDR3 1600 2GB Ramaxel RMT3150ED58E8W 1600 DDR3 1600 2GB DDR3 1600 2GB Sharetronic Micron SM321NHO8IAF DDR3 1600 2GB DDR3 1600 2GB Samsung M471B5773DH0 CK0 DDR3 1600 2GB DDR3 1600 4GB Samsung M471B5273DH0 CK0 DDR3 1600 4GB DDR3 1600 4GB Micron MT16KTF51264HZ 1G6M1 DDR3 1600 4GB DDR3 1600 4GB Hynix HMT351S6CFR8C PB DDR3 1600 4GB FRU no 102500106 TBD 102500084 102001132 90200252 90200252 121500057 121500061 16200068 16005024 16005211 16200067 16200194 16005030 16200195 16200108 16200162 90200280 90200280 11200343 11200346 11200392 11200396 11200340 11200341 11200347 11200344 CRU ID EE EE aka aka ak EE ES ES EE EE za EE EE EE EE 65 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 66 Table 4 Parts list Overall continued No FRU 14 DDR3 1600 4GB Ramaxel RMT3160ED58E9W 1600 DDR3 1600 4GB 14 DDR3 1600 4GB Sharetronic Micron SM322NQ0
12. LED Sponge S206 WINNIE LVDS Cable ASSY S200 WINNIE LVDS Cable S206 FRU no 90200260 90200299 18200146 18200147 18200148 18200149 90200279 90200279 90200256 90200256 90200264 90200264 90200262 90200262 90200263 90200263 90200278 90200278 90200266 90200266 CRU ID Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Keyboard Lenovo IdeaPad S200 S206 Table 6 Parts list Keyboard Language 5200 5206 Sunrex black Sunrex white Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Ttalian U K English English Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German P N 25201724 25201723 25201722 25201721 25201720 25201719 25201718 25201717 25201716 25201715 25201714 25201713 25201712 25201711 25201710 25201709 25201708 25201707 25201706 25201705 25201704 25201703 25201702 25201701 25201700 25201699 25201698 25201697 25201696 25201754 25201753 25201752 25201751 25201750 25201749 25201748 25201747 25201746 25201745 25201744 25201743 25201742 25201741 25201740 2520
13. Only certified trained personnel can service the computer Before replacing any FRU read the entire page on removing and replacing FRUs When you replace FRUs use new nylon coated screws Be extremely careful during such write operations as copying saving or formatting Drives in the computer that you are servicing sequence might have been altered If you select an incorrect drive data or programs might be overwritten Replace an FRU only with another FRU of the correct model When you replace an FRU make sure that the machine model and the FRU part number are correct by referring to the FRU parts list An FRU should not be replaced just because of a single unreproducible failure Single failures can occur for a variety of reasons that have nothing to do with a hardware defect such as cosmic radiation electrostatic discharge or software errors Consider replacing an FRU only when a problem recurs If you suspect that an FRU is defective clear the error logs and run the test again If the error does not recur do not replace the FRU Be careful not to replace a nondefective FRU 19 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual What to do first to do first When you do return an FRU you must include the following information in the parts exchange form or parts return form that you attach to it 20 1 9e NI Un ag Pe Name and phone number of servicer Date of service Date on which the machine fa
14. fully charged Off The battery is detached Lenovo IdeaPad 200 S206 Fn key combinations key combinations The following table shows the function of each combination of Fn with a function key Table 3 Fn key combinations Key combination Description Fn PgUp Activate the Home function Fn PgDn Activate the End function o 10 The hotkeys are located in the function key row of the keyboard By pressing the appropriate hotkey you can change system settings instantly The following describes the function of each hotkey Table 4 Hotkeys Hotkeys Description Mute Unmute Decrease sound volume Increase sound volume Close active window or program Refresh desktop or Web pages Enable Disable the touchpad Open the interface for integrated wireless devices settings on off Enable Disable the built in microphone Turn on off the integrated camera om Open the interface for changing display devices Turn on off the backlight of the LCD screen Decrease display brightness Increase display brightness 31 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual FRU replacement notices replacement notices 32 This section presents notices related to removing and replacing parts Read this section carefully before replacing any FRU Screw notices Loose screws can cause a reliability problem In the Lenovo computer this problem is addressed with special nylon coated screws th
15. lo bater as que se encuentren en la lista de piezas La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma Safety information Safety notice 3 A DANGER The battery pack contains small amounts of nickel Do not disassemble it throw it into fire or water or short circuit it Dispose of the battery pack as required by local ordinances or regulations Use only the battery in the appropriate parts listing when replacing the battery pack Use of an incorrect battery can result in ignition or explosion of the battery La batterie contient du nickel Ne la d montez pas ne l exposez ni au feu ni l eau Ne la mettez pas en court circuit Pour la mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la batterie veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es ad quate En effet une batterie inappropri e risque de prendre feu ou d exploser Akkus enthalten geringe Mengen von Nickel Sie d rfen nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sondermiill beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren 5p Sw nog NM 522 NIINON INI pownd Addon TANK DN p5235 PN DIT PA DN DO V INN IS
16. sont bien en place et bien fix es Pour ce faire secouez l unit et assurez vous qu aucun bruit suspect ne se produit Des pi ces m talliques ou des copeaux de m tal pourraient causer un court circuit Bevor nach einem FRU Austausch der Computer wieder angeschlossen wird muf sichergestellt werden daf keine Schrauben Federn oder andere Kleinteile fehlen oder im Geh use vergessen wurden Der Computer muf gesch ttelt und auf Klapperger usche gepr ft werden Metallteile oder splitter k nnen Kurzschl sse erzeugen Mm W FRU NINN ANN awnyan NIYIN ab DNS DANN DP DPIN O vsgn 0n 55V N79 979 AYNA TINA MI DYWAN DYN DNPH PW V MAN 199 PUPAD AWNAN AN 20205 W nt DIN 091899 ON DDI NINN aav IN PAN Prima di accendere l elaboratore dopo che stata effettuata la sostituzione di una FRU accertarsi che tutte le viti le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all interno dell elaboratore Verificare ci scuotendo l elaboratore e prestando attenzione ad eventuali rumori eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi FRU DZMH IVE A NRZ ANDANT AL A TOUDE HOST TIE LIME ERIC 2 OAR CRA TOOT L ARL TLES INERAT DIA AV ea REIT DZ D Ze LELRO E FI RAMPEI a KORRIZAZRSI EBD ET Antes de encender el sistema despues de sustituir una FRU compruebe que todos los tornillos muelles y dem s piezas peque as se encuentran en su
17. the instructions on the screen to complete the Windows setup Passwords 24 As many as three passwords may be needed for any Lenovo computer the power on password POP the hard disk password HDP and the supervisor password SVP If any of these passwords has been set a prompt for it appears on the screen whenever the computer is turned on The computer does not start until the password is entered Exception If only an SVP is installed the password prompt does not appear when the operating system is booted Power on password A power on password POP protects the system from being powered on by an unauthorized person The password must be entered before an operating system can be booted Hard disk password There are two hard disk passwords HDPs User HDP for the user Master HDP for the system administrator who can use it to get access to the hard disk drive even if the user has changed the user HDP Attention If the user HDP has been forgotten check whether a master HDP has been set If it has it can be used for access to the hard disk drive If no master HDP is available neither Lenovo nor Lenov authorized service technicians provide any services to reset either the user or the master HDP or to recover data from the hard disk drive The hard disk drive can be replaced for a scheduled fee Supervisor password A supervisor password SVP protects the system information stored in the BIOS Setup Utili
18. the system board bear the following in mind Be careful not to drop the system board on a bench top that has a hard surface such as metal wood or composite Avoid rough handling of any kind In the whole process make sure not to drop or stack the system board If you put a system board down make sure to put it only on a padded surface such as an ESD mat or conductive corrugated material M J For access remove these FRUS in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 45 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 46 Figure 8 Removal steps of system board Remove six screws H on the system board two screws Efl on the IO board and single screw J on the fan Detach the power board connector in the direction shown by arrows DD unplug the speaker connector in the direction shown by arrow HM system board power connector in the direction shown by arrow El two LCD connectors in the direction shown by arrows Ki E When installing Make sure that all the connectors are attached firmly Step Screw quantity Color Torque H M2X3mmn flathead nylok coated 2 Silver 1 5 kgfcm H M2 x 2 5 mm flat head nylok coated 6 Black 1 5 kgfcm H M2x25mm flat head nylok coated 1 Black 1 5 kgfcm Lenovo IdeaPad 5200
19. the top center of the LCD cover Remove the integrated camera from the LCD cover Efl When installing Stick the integrated camera to the top center of the LCD cover and ajust the placement of it to make sure the connector is attached firmly Lenovo IdeaPad 200 S206 Front view H Integrated camera On select models BH Wireless module antennas On select models EJ Computer display El Power button H Fan louvers D Touchpad 59 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual Right side view H Memory card slot B USB 2 0 port E OneKey Rescue system button 60 Lenovo IdeaPad 5200 5206 Bottom and Left side view H Louvers El Speakers E System status indicators D AC power adapter jack D HDMI port D USB 3 0 port Combo audio jack D SIM card slot on select models E Built in microphone 61 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Parts it This section presents the following service parts Overall on page 63 LCD FRUs on page 67 Keyboard on page 69 Miscellaneous parts on page 73 AC adapters on page 74 Power cords on page 75 Notes Each FRU is available for all types or models unless specific types or models are specified 62 Lenovo IdeaPad 5200 5206 Overall 8 1 63 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Table 4 Parts list Overall No FRU FRU no CRU ID 1 LCD unit see LCD FRUs
20. 1739 CRU ID za 69 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Table 6 Parts list Keyboard continued Language Sunrex white continued 5200 8206 continued Chicony black 70 French Russian Traditional Chinese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Italian U K English English Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Italian U K English English P N 25201738 25201737 25201736 25201735 25201734 25201733 25201732 25201731 25201730 25201729 25201728 25201727 25201726 25201664 25201663 25201662 25201661 25201660 25201659 2520 658 25201657 2520 2520 2520 656 655 654 25201653 25201652 25201651 2520 2520 650 649 25201648 25201647 25201646 25201645 2520 644 25201643 2520 642 25201641 25201640 25201639 25201638 25201637 25201636 CRU ID za Lenovo IdeaPad S200 S206 Table 6 Parts list Keyboard continued Language 5200 8206 continued Chicony white Dafon black Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries H
21. 2 Overall 63 LCD FRUs 67 Keyboard Miscellaneous parts AC adapters Power COTAS aai an aka kk k k Notices eeeeeeeeeeeee eene 78 Ta nci ci 79 iii iv This manual contains service and reference information for the following Lenovo product Lenovo IdeaPad S200 S206 Use this manual to troubleshoot problems The manual is divided into the following sections The common sections provide general information guidelines and safety information required for servicing computers The product specific section includes service reference and product specific parts information Important This manual is intended only for trained servicers who are familiar with Lenovo products Use this manual to troubleshoot problems effectively Before servicing a Lenovo product make sure to read all the information under Safety information on page 1 and Important service information on page 16 Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo computer General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices multilingual translations on page 7 Laser compliance statement on page 14 Lenovo IdeaPad 5200 520
22. 45000560 145000559 145000558 145000557 145000556 145000555 145000554 145000553 145000538 145000537 145000536 145000535 145000534 145000533 145000532 145000531 145000530 145000528 CRU ID Lenovo IdeaPad S200 S206 Table 9 Parts list 3 pin power cords continued Region P N CRU ID Brazil 145000527 e VOLEX CH10S3 H03VV F VAC5S 1m i Israel 145000526 e VOLEX SI16S3 H03VV F VAC5S 1m CE 145000525 e VOLEX M2511 HO3VV F VAC5S Im Switzerland 145000524 e VOLEX MP232 HO3VV F VAC5S 1m UK 145000605 VOLEX MP5004 H03VV F VAC5S 1m Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 78 Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to
23. 5206 Figure 8 Removal steps of system board continued Remove the system board in the direction shown by arrow EJ When installing When attaching the system board to the base cover adjust the placement of the USB HDMI Power jacks as shown in EI 9 E and make sure that they are attached to the holes on the base cover as shown Improper placement of those jacks might cause a damage 47 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1090 LCD unit For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 Figure 9 Removal steps of LCD unit Remove four screws Efl Step Screw quantity Color Torque H M2 x 3 5 mm flat head nylok coated 4 Silver 1 5 kgfem When installing Route the antenna cables along the cable guides As you route the cables make sure that they are not subjected to any tension Tension could cause the cables to be damaged by the cable guides or a wire to be broken Make sure that the LCD connector is attached firmly and make sure that you do not pinch the antenna cables when you attach the LCD assembly Route the LCD cable along the cable guides 48 Lenovo IdeaPad 5200 5206 Figure 9 Removal steps of LCD unit continued Remove the LCD un
24. 6 Hardware Maintenance Manual General safety safety Follow these rules below to ensure general safety Observe a good housekeeping in the area where the machines are put during and after the maintenance When lifting any heavy object 1 Make sure that you can stand safely without slipping 2 Distribute the weight of the object equally between your feet 3 Use a slow lifting force Never move suddenly or twist when you attempt to lift it 4 Lift it by standing or pushing up with your leg muscles this action could avoid the strain from the muscles in your back Do not attempt to lift any object that weighs more than 16 kg 35 Ib or that you think is too heavy for you Do not perform any action that causes hazards to the customer or that makes the machine unsafe Before you start the machine make sure that other service representatives and the customer are not in a hazardous position Please remove covers and other parts in a safe place away from all personnel while you are servicing the machine Keep your toolcase away from walk areas so that other people will not trip it over Do not wear loose clothing that can be trapped in the moving parts of the machine Make sure that your sleeves are fastened or rolled up above your elbows If your hair is long fasten it Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip about 8 centimeters 3 inches from the end Do not
25. 8IAF DDR3 1600 4GB 15 Touchpad 55 90 Synaptics TM 02042 001 15 Touchpad 55 90 Cypress CYTRA 104008 00 15 WINNIE TP Module ASSY S200 15 WINNIE TP Module S206 15 1 WINNIE TouchPad Button Board ASSY S200 15 1 WINNIE TouchPad Button Board S206 15 1 WINNIE TP PMMA S200 15 1 WINNIE TP PMMA S206 FRU no 11200393 11200397 73040641 73040625 90200265 90200265 90200311 90200311 90200281 90200281 CRU ID E ES Lenovo IdeaPad 5200 5206 LCD FRUs In Lenovo IdeaPad 5200 5206 there are following types of LCDs e 17 3 in HD TFT 67 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 68 17 3 in HD TFT Table 5 Parts list 17 3 in HD TFT No v 0060 4 4 Oh Oh GAT s SW UC FRU WINNIE LCD Bezle Grey Bcover_Grey S200 WOODY LCD Bezle Black S206 Panel 11 6 Flat AUO AUO B116XW03 VO HD G F LED1 NB LCD Panel 11 6 Flat CMI CMI N116BGE L42 HD G FLED1 NB LCD Panel 11 6 Flat SEC SEC LTN116AT06 L02 HD G F LED1 NB LCD Panel 11 6 Flat IVO IVO MI16NWRI R4 HD G F LED1 NBLCD WINNIE Camera Board 0 3M CAM 0 3M S200 WINNIE Camera Board 0 3M S206 WINNIE LCD Cover Grey Acover Grey 5200 WINNIE LCD Cover Grey S206 WINNIE LCD Hinge Cover ASSY 200 WINNIE LCD Hinge Cover S206 WINNIE LCD Hinge L ASSY 200 WINNIE LCD Hinge L 206 WINNIE LCD Hinge R ASSY 200 WINNIE LCD Hinge R S206 WINNIE Camera LED Sponge ASSY S200 WINNIE Camera
26. 90 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 Figure 11 Removal steps of base cover speakers and power assembly Remove screw fi Lift the power assembly in the direction shown by arrow EJ Step Screw quantity Color Torque H M2 x 3 mm flat head nylok coated 1 Silver 1 5 kgfem 52 Lenovo IdeaPad 5200 5206 Remove four screws E and then remove the speakers in the direction shown by arrows Ej Step Screw quantity Color Torque BH M2 x 3 mm flat head nylok coated 4 Silver 1 5 kgfcm 53 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 54 Note Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds When you replace the base cover you need to apply the following label The following labels need to be peeled off from the old base cover and need to be put on the new base cover CPU Label e Standby Label KOR Rating Label COA Label 3G Label Malaysia WLAN Label Israel WLAN Label Brazil WLAN Label WLAN Label for CA US TW Indonesia Israel KCC Label aa 2 RO ECL CE E sa gt For some models you also need to apply one or two FCC labels Check the old base cover if it has one or two FCC labels find duplicates of them in the label kit and apply them to the new base cover For the location of each label refer to the following figure Dol poe CH LIE IC
27. ERIC TRIK IC d o Cfi 5 ION AAA MORAN CA TES VS Sila LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos lave inmediatamente las reas afectadas con agua durante 15 minutos como m nimo Obtenga atenci n medica si se presenta alg n X J 11 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 12 Safety notice 6 A DANGER To avoid shock do not remove the plastic cover that protects the lower part of the inverter card Afin d viter tout risque de choc lectrique ne retirez pas le cache en plastique prot geant la partie inf rieure de la carte d alimentation Aus Sicherheitsgr nden die Kunststoffabdeckung die den unteren Teil der Spannungswandlerplatine umgibt nicht entfernen prooLban NUI AN ONI N monunnn YI 913 pann 990997 90 ANNA IPIN by yan Per evitare scosse elettriche non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore MBE CID AVI AL FOTWERSUCOSZZATyZ NEIE ROT EEN Para evitar descargas no quite la cubierta de pl stico que rodea la parte baja de la tarjeta invertida Safety notice 7 A DANGER Though the main batteries have low voltage a shorted or grounded battery can produce enough current to burn personnel or combustible materials Bien que le voltage des batteries principales soit peu lev le court circuit ou la mise la masse d une batterie peut produire suffisamment de cour
28. ETUTCIUI ITT DOBUOUL J LC CL S EE C O H Lenovo IdeaPad 5200 5206 1120 LCD front bezel For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover speakers and power assembly on page 52 Figure 12 Removal steps of LCD front bezel Remove the LCD front bezel in the direction shown by arrows i 55 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1130 LCD panel LCD cable and hinges For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover speakers and power assembly on page 52 1120 LCD front bezel on pa
29. OB a TAKKE u3berante npamoro Bo3AelicrBus nasepHoro nysa Ked je laserov jednotka otvoren Vyhnite sa priamemu poh adu a nehladte priamo s optick mi n strojmi do l ta a vyhnite sa priamemu vystaveniu l ov HJELP HERB SIET RARO HFR TE TV UZz vv C42 SV Radiaci n l ser al abrir No mire fijamente ni examine con instrumental ptico el haz de luz Evite la exposici n directa al haz 15 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual _ Important service information This chapter presents the following important service information Strategy for replacing FRUs on page 16 Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17 Important information about replacing RoHS compliant FRUs on page 18 Important BIOS and device driver fixes are customer installable The BIOS and device drivers are posted on the customer support site http consumersupport lenovo com Strategy for replacing FRUs for replacing FRUs Before replacing parts Make sure that all software fixes drivers and BIOS downloads are installed before replacing any FRUs listed in this manual After a system board is replaced ensure that the latest BIOS is loaded to the system board before completing the service action To download software fixes drivers and BIOS follow the steps below 1 Go to http consumersupport lenovo com 2 Enter t
30. OM drive or any other optical storage device could result in exposure to hazardous laser radiation There are no serviceable parts inside those drives Do not open 14 Safety information A CD ROM drive a DVD ROM drive or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode Note the following la N DANGER Emits visible and invisible laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Radiac o por raio laser ao abrir Nao olhe fixo no feixe de luz nao olhe diretamente por meio de instrumentos ticos e evite exposic o direta com o feixe de luz ZER ep EN SHEET NBA DES FF EE BRE BOWER A Rayonnement laser si carter ouvert Evitez de fixer le faisceau de le regarder directement avec des instruments optiques ou de vous exposer au rayon Laserstrahlung bei ge ffnetem Ger t Nicht direkt oder tiber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden Kinyit skor l zersug r Ne n zzen bele se szabad szemmel se optikai eszk z kkel Ker lje a sug rnyal bbal val rintkez st Aprendo l unit vengono emesse radiazioni laser Non fissare il fascio non guardarlo direttamente con strumenti ottici e evitare l esposizione diretta al fascio OrkpbiBas Geperwrecb nasepHoro usnyyeHna He cmoTpuTe Ha nyy He pasrnaabiBante ero C TlOMOLLIBIO ONTUYECKUX VHCTPYMEHT
31. PI IN 0999 IN UND INN mann zm 59 WINI ASADA AION INA A55Y03 p DPI W 0 5172n OPINNI NINA pata AANA o p2nn nav 3 NDA 2129 MINIMA NI NINDI VIV INON INI AINON 5v MIVINA IN ANSNI DINI La batteria contiene piccole quantit di nichel Non smontarla gettarla nel fuoco o nell acqua n cortocircuitarla Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa SITU D8vyZiuD EO yvMEREnpCOOET NYT Y RVD VAMUIEU KEKIIKORIZRITAAKI Y Ya bh SURV ESV RYT VY uer I OBERIC biro CH HBB KORE LAI HES C CREW NYT U9 NYT RRRT SLE tee Ha RI SITIO SEAL TSC RES Rolky I EATE ST Y BREKUEO RELIEVTSIERSVET Las bater as contienen peque as cantidades de n quel No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas al sustituir la bater a La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 10 Safety notice 4 N DANGER The lithium battery can cause a fire an explosion or a severe burn Do not recharge it remove its polariz
32. The system board is sensitive to and can be damaged by electrostatic discharge Before touching it establish personal grounding by touching a ground point with one hand or using an electrostatic discharge ESD strap P N 6405959 to remove potential shock reasons 33 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1010 Battery pack N DANGER Only use the battery specified in the parts list for your computer Any other battery could ignite or explode Figure 1 Removal steps of battery pack Open two rubber foot pads with a screw driver in the direction shown by arrow El then remove two screws EJ VO WH L Step Screw quantity Color Torque H M2 x 5 mm flat head nylok coated 2 Black 2 0 kgfem Open the back cover along the device frame with a flat blade in the direction shown by arrows and then lift the back cover in the direction shown by arrow v sos V E 34 Lenovo IdeaPad 5200 5206 Figure 1 Removal steps of battery pack continued Detach the system board connector in the direction shown by arrows Ell El unplug the battery connector in the direction shown by arrow E remove five screws Ef Step Screw quantity Color Torque E M2 x 3 mm flat head nylokcoated 5 Silver 1 5 kgfcm Remove the battery in the direction shown by arrow E 35 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1020 Dummy card Figure 2 Removal steps of dummy cards
33. VIIAOS AMIN DANY IN ANN P4999 09 AIPA PRI n55Yon NN PIWI PR PTT MIYA 100 99 n5yn VINI ASDC NN PIDI v D DP NAN 1n nx UNI IDNA g VANWAI v n 1213n D DP Dm NINDI VIV DIONHAN o pann nma v a n avan MANIANN IN MD 3295 DIZAY 5125 NINN La batteria di supporto e una batteria al litio e puo incendiarsi esplodere o procurare gravi ustioni Evitare di ricaricarla smontarne il connettore polarizzato smontarla riscaldarla ad una temperatura superiore ai 100 gradi centigradi incendiarla o gettarla in acqua Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa FDA RYTY KR BH ELMBEOCU Carla col d DUET aha RVFV ORE COMETAS F ORVAL RYT VY ABD 100 C 212 F LETOMAN HA EMO PSTAKTIEFI LHLIBNT KS Oo 77 Y ERES SRAM RARO RMN ES TS REV ABD AY DARIA YT ERA UI RE MOR AYT YE BATSL NYT U RBBKLICV BPBLIEVTSILBHSVET La bateria de repuesto es una bateria de litio y puede provocar incendios explosiones o quemaduras graves No la recargue ni quite el conector polarizado ni la desmonte ni caliente por encima de los 100 C 212 F ni la incinere ni exponga el contenido de sus celdas al agua Des chela tal como dispone la normativa local y Safety information G y Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your han
34. afe conditions such as metal filings contamination water or other liquids or signs of fire or smoke damage 8 Check for worn frayed or pinched cables 9 Check that the power supply cover fasteners screws or rivets have not been removed or tampered with a Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits ICs should be considered sensitive to electrostatic discharge ESD ESD damage can occur when there is a difference in charge between objects Protect against ESD damage by equalizing the charge so that the machine the part the work mat and the person handling the part are all at the same charge Notes 1 Use product specific ESD procedures when they exceed the requirements noted here 2 Make sure that the ESD protective devices you use have been certified ISO 9000 as fully effective When handling ESD sensitive parts Keep the parts in protective packages until they are inserted into the product Avoid contact with other people Wear a grounded wrist strap against your skin to eliminate static on your body Prevent the part from touching your clothing Most clothing is insulative and retains a charge even when you are wearing a wrist strap Use the black side of a grounded work mat to provide a static free work surface The mat is especially useful when handling ESD s
35. al charging To check the AC adapter follow the steps below 1 Unplug the AC adapter cable from the computer 2 Measure the output voltage at the plug of the AC adapter cable See the following figure Pin Voltage V DC 1 20 2 0 Note Output voltage for the AC adapter pin No 2 may differ from the one you are servicing 3 If the voltage is not correct replace the AC adapter 4 If the voltage is acceptable do the following Replace the system board If the problem persists go to Lenovo IdeaPad 5200 5206 on page 27 Note Noise from the AC adapter does not always indicate a defect Checking operational charging To check whether the battery charges properly during operation use a discharged battery pack or a battery pack that has less than 50 of the total power remaining when installed in the computer 21 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 22 Perform operational charging If the battery status indicator or icon does not light on remove the battery pack and let it return to room temperature Reinstall the battery pack If the charge indicator or icon is still off replace the battery pack If the charge indicator still does not light on replace the system board Then reinstall the battery pack If it is still not charged go to the next section Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95
36. ant pour br ler des mat riaux combustibles ou causer des br lures corporelles graves Obwohl Hauptbatterien eine niedrige Spannung haben k nnen sie doch bei Kurzschluf oder Erdung genug Strom abgeben um brennbare Materialien zu entz nden oder Verletzungen bei Personen hervorzurufen AINO TWA nia MIYA YN NPWNAN MddOAY AN Nd PAVN DIT PAINI NDIY NINA IN NINPA PIT BAIN nnsn5 IN DNI Sebbene le batterie di alimentazione siano a basso voltaggio una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione ju rier HOER Tb Va PLE enka yA Mgr CERDETO UN WASH ISO O TEE A EARD EN ET Aunque las bater as principales tienen un voltaje bajo una bater a cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal Safety information Safety notice 8 A DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any interconnecting cables Avant de retirer une unit remplacable en client le mettez le syst me hors tension d branchez tous les cordons d alimentation des socles de prise de courant retirez la batterie et d connectez tous les cordons d interface Die Stromzufuhr muf abgeschaltet alle Stromkabel aus der Steckdose gezogen de
37. at have the following characteristics They maintain tight connections They do not easily come loose even with shock or vibration They are harder to tighten Each one should be used only once Do the following when you service this machine Keep the screw kit in your tool bag Always use new screws Usea torque screwdriver if you have one Tighten screws as follows Plastic to plastic Turn an additional 90 after the screw head touches the surface of the plastic part more than 90 Z Cross section Logic card to plastic Turn an additional 180 after the screw head touches the surface of the logic card more than 180 4 A E ZZ 2 S Cross section Torque driver If you have a torque screwdriver refer to the Torque column for each step Make sure that you use the correct screws If you have a torque screwdriver tighten all screws firmly to the torque shown in the table Never use a screw that you removed Use a new one Make sure that all screws are tightened firmly Ensure torque screwdrivers are calibrated correctly following country specifications Lenovo IdeaPad 200 S206 Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU Make sure to observe the following general rules 1 Do not attempt to service any computer unless you have been trained and certifi
38. card WiFi 1x1 BGN BT4 0 CyberTan Cbt 20002501 ee BCM4313HMGB BGN BT HMC WLAN card 7 WLAN card WiFi 1x1 BGN BT3 0 Liteon Liteon 20002524 KW WB195 BGN BT HMC WLAN card 8 WINNIE Thernal Module W Fan S206 90200261 me 8 1 WINNIE THM Fan S200 90200283 8 1 WINNIE HeatSink S200 90200284 9 1 Chipset Cedar Trail Intel Intel Tiger Point 82NM10 BO 1007357 ae S200 9 1 Chipset Brazos AMD AMD A50M FCH S206 1007341 9 Intel N2600 1 6G B2 3 5W 2cBGA processor S200 102500105 Lenovo IdeaPad S200 S206 Table 4 Parts list Overall continued 11 12 12 12 12 12 12 12 12 12 13 13 14 14 14 14 14 14 14 14 FRU Intel N2800 1 86G B2 6 5W 2cBGA processor S200 Intel N2100 1 6G B2 3W 1cBGA ES processor S200 AMD C60 1 3G 1 0G 1M 2C C0 BGA CPU S206 AMD C50 1 0G 1M 2C B0 BGA CPU S206 WINNIE Lower Case Grey Dcover Grey S200 WINNIE Lower Case Grey S206 Battery 251P 2cell 3740mAh 27Wh SMP 5200 SMP ATL L11M2P01 2S1P 27Wh bty Battery 251P 2cell 3600mAh 27Wh Sanyo S200 Sanyo L11S2P01 2S1P 27Wh bty Hard disk drive 320G 5400rpm HGST HTS545032A7E380 5400PRM7mm 320G HDD Hard disk drive 320G 5400rpm HGST HTS543232A7A384 5 4K RPM 320G HDD Hard disk drive 320G 5400rpm Seagate ST320LT020 5400RPM 7MM 320G HDD Hard disk drive 500G 5400rpm HGST HTS545050A7E380 5400PRM7mm 500G HDD Hard disk drive 320G 7200rpm HTS725032A7E630 7 2K rpm
39. ds immediately wash the affected areas with water at least for 15 minutes Seek medical care if any symptoms caused by the fluid are present after washing Si le panneau d affichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide rincez les abondamment pendant au moins quinze minutes Consultez un m decin si des sympt mes persistent apr s le lavage Die Leuchtstoffr hre im LCD Bildschirm enth lt Quecksilber Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Der LCD Bildschirm besteht aus Glas und kann zerbrechen wenn er unsachgema amp behandelt wird oder der Computer auf den Boden f llt Wenn der Bildschirm besch digt ist und die darin befindliche Fl ssigkeit in Kontakt mit Haut und Augen ger t sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesp lt und bei Beschwerden anschlie end ein Arzt aufgesucht werden 3992 N2 TONN TNA 2vom aav LCD HNN WAN TOM ON Jnl DANI PN DYDIN DOMAN NN VW DPT IN D y DY DINA DPMON ON MNI MAY 2395 M9 mno mp 15 DOWN ANN DIVA Drun DY yyann Nel caso che caso l LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti poi consultare un medico se i sintomi dovessero permanere LCD DIHAL LCD OP ORAM A IZA ote DI Ficfi r o LERNE W afin Te Zeb IRA ES 15 UG ACL TS ToS BEVEL
40. e RoHS and non RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo s requirements and schedule in the EU Products sold in 2005 and 2006 will contain some RoHS compliant FRUs The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs RoHS compliant FRUs have unique FRU part numbers Before or after the RoHS implementation date failed RoHS compliant parts must always be replaced with RoHS compliant ones so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used Products marketed before June 2006 Products marketed after June 2006 Current or Replacement Current or Replacement original part FRU original part FRU Non RoHS Can be Non RoHS Non RoHS Can be RoHS Must be RoHS Must be RoHS Non RoHS Can sub to RoHS RoHS Must be RoHS Note A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order 18 General checkout General checkout This chapter presents the following information What to do first on page 20 Power system checkout on page 21 Before you go to the checkout make sure to read the following important notes va Important notes
41. ed An untrained person runs the risk of damaging parts 2 Before replacing any FRU review FRU replacement notices on page 32 3 Begin by removing any FRUs that have to be removed before the failing FRU Any of such FRUs are listed at the top of the page Remove them in the order in which they are listed 4 Follow the correct sequence in the steps to remove the FRU as given in the figures by the numbers in square callouts 5 When turning a screw to replace an FRU turn it in the direction as given by the arrow in the figure 6 When removing the FRU move it in the direction as given by the arrow in the figure 7 To put the new FRU in place reverse the removal procedures and follow any of the notes that pertain to replacement For information about connecting and arranging internal cables see Locations on page 59 8 When replacing an FRU use the correct screw as shown in the procedures N DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any of the interconnecting cables Attention After replacing an FRU do not turn on the computer until you have made sure that all screws springs and other small parts are in place and none are loose inside the computer Verify this by shaking the computer gently and listening for rattling sounds Metallic parts or metal flakes can cause electrical short circuits Attention
42. ed connector disassemble it heat it above 100 C 212 F incinerate it or expose its cell contents to water Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery La pile de sauvegarde contient du lithium Elle pr sente des risques d incendie d explosion ou de br lures graves Ne la rechargez pas ne retirez pas son connecteur polaris et ne la d montez pas Ne l exposez pas une temperature sup rieure 100 C ne la faites pas br ler et n en exposez pas le contenu l eau Mettez la pile au rebut conform ment la r glementation en vigueur Une pile inappropri e risque de prendre feu ou d exploser Die Systembatterie ist eine Lithiumbatterie Sie kann sich entz nden explodieren oder schwere Verbrennungen hervorrufen Batterien dieses Typs d rfen nicht aufgeladen zerlegt ber 100 C erhitzt oder verbrannt werden Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren IN mssonnb 099799 01535 n515y AVMIIN noo JANDA DN PID WAN AMIN PYOY PN nup N99 AM
43. ensitive devices Select a grounding system such as those listed below to provide protection that meets the specific service requirement Notes The use of a grounding system to guard against ESD damage is desirable but not necessary Attach the ESD ground clip to any frame ground ground braid or green wire ground When working on a double insulated or battery operated system use an ESD common ground or reference point You can use coax or connector outside shells on these systems Use the round ground prong of the ac plug on ac operated computers Grounding requirements requirements Electrical grounding of the computer is required for operator safety and correct system function Proper grounding of the electrical outlet can be verified by a certified electrician Safety information Safety notices multilingual translations The safety notices in this section are provided in English French German Hebrew Italian Japanese and Spanish A Safety notice 1 Before the computer is powered on after FRU replacement make sure all screws springs and other small parts are in place and are not left loose inside the computer Verify this by shaking the computer and listening for rattling sounds Metallic parts or metal flakes can cause electrical shorts Avant de remettre l ordinateur sous tension apr s remplacement d une unit P P en client le v rifiez que tous les ressorts vis et autres pieces
44. from the hard disk drive 26 Lenovo IdeaPad 200 S206 Lenovo IdeaPad S200 S206 _ This chapter presents the following product specific service references and product specific parts information Specifications on page 27 Status indicators on page 29 FRU tests on page 31 Fn key combinations on page 31 FRU replacement notices on page 32 Removing and replacing an FRU on page 33 Locations on page 59 Parts list on page 62 Specifications The following table lists the specifications of the Lenovo IdeaPad 5200 5206 Table 1 Specifications Lenovo IdeaPad S200 Lenovo IdeaPad S206 Feature Description Processor Intel Cedar Trail M AMD Brazos Core Chipset Intel NM10 AMD A50M FCH Bus architecture 1066MHz DDR3 SDRAM 1066MHz DDR3 SDRAM PC2 8500 PC2 8500 PCIbus PCI Express bus PCI Express bus UMI DMI Graphic Chipset Intel Integrated Graphics AMD Radeon HD 6290 C60 Display 11 6 SD LED backlight Flat type 1366 x 768 pixel Standard DDR3 800 or DDR3 1066 DDR3 1066 1x2GB 4GB slot memory 1x2GB 4GB slot Max Max Memory 4GB Memory 4GB CMOS RAM 256 bytes Hard disk drive 2 5 HDD 7mm 500GB 5400rpm 7200rpm 320GB 5400rpm 7200rpm Optical drive Support USB external ODD 27 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 28 Table 1 Specifications continued Feature I O ports Audio Video WLAN WWAN Bluetooth Keyboard Touch pad Integrated camera Bat
45. ge 55 Figure 13 Removal steps of LCD panel LCD cable and hinges Remove four screws H disconnect the connector in the direction shown by a rrow Efl N Step Screw quantity Color Torque H M2 x 3 5 mm flat head nylok coated 4 Silver 1 5 kgfem Disconnect the connector E lift the LCD panel in the direction shown by arrow When installing Make sure that the connector is attached firmly 56 Lenovo IdeaPad 5200 5206 Figure 13 Removal steps of LCD panel LCD cable and hinges Remove eight screws E and the hinges in the direction shown by arrows D Step Screw quantity Color Torque E M2 x 3 5 mm flat head nylokcoated 8 Silver 1 5 kgfcm Note The LCD cables are attached to the LCD panel by a metal connector 57 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 58 1140 Integrated camera For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 1090 LCD unit on page 48 1100 Fan assembly and Heat Sink assembly on page 50 1110 Base cover speakers and power assembly on page 52 1120 LCD front bezel on page 55 1130 LCD panel LCD cable and hinges on page 56 Figure 14 Removal steps of integrated camera Note The integrated camera is stuck on
46. he serial number or select a product or use Lenovo smart downloading 3 Select the BIOS Driver Applications and download 4 Follow the directions on the screen and install the necessary software 16 Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs If you are instructed to replace an FRU but the replacement does not solve the problem reinstall the original FRU before you continue Some computers have both a processor board and a system board If you are instructed to replace either of them and replacing one of them does not solve the problem reinstall that board and then replace the other one e Ifan adapter or a device consists of more than one FRU any of the FRUs may be the cause of the error Before replacing the adapter or device remove the FRUs one by one to see if the symptoms change Replace only the FRU that changed the symptoms Attention The setup configuration on the computer you are servicing may have been customized Running Automatic Configuration may alter the settings Note the current configuration settings using the View Configuration option then when service has been completed verify that those settings remain in effect Strategy for replacing a hard disk drive Always try to run a low level format before replacing a hard disk drive This will cause all customer data on the hard disk to be lost Make sure that the customer
47. hout incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Notices Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment Trademarks The following terms are either registered trademarks or trademarks of Lenovo in the United States and or other countries Lenovo Lenovo logo IdeaPad VeriFace OneKey Rescue OneKey Recovery OneKey Antivirus APS Power Express Energy Management and ReadyComm The following terms are trademarks of Microsoft Corporation in the United States other countries or both Windows Windows 7 The following are trademarks of Intel Corporation or its subsidiaries in the United States other countries or both Intel Intel Core 2 Duo The fo
48. iled Date of purchase Procedure index and page number in which the failing FRU was detected Failing FRU name and part number Machine type model number and serial number Customer s name and address Note for warranty During the warranty period the customer may be responsible for repair costs if the computer damage was caused by misuse accident modification unsuitable physical or operating environment or improper maintenance by the customer The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use Before checking problems with the computer determine whether the damage is covered under the warranty by referring to the following list The following are not covered under warranty LCD panel cracked from the application of excessive force or from being dropped Scratched cosmetic parts Distortion deformation or discoloration of the cosmetic parts Plastic parts latches pins or connectors that have been cracked or broken by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Improper disk insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover foreign material in the drive or the insertion of a diskette with multiple labels Damaged or bent diske
49. in your electrical hand tools for safe operational condition Do not use worn or broken tools and testers Never assume that power has been disconnected from a circuit First check it to make sure that it has been powered off SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Always look carefully for possible hazards in your work area Examples of these hazards are moist floors nongrounded power extension cables power surges and missing safety grounds Do not touch live electrical circuits with the reflective surface of a plastic dental mirror The surface is conductive such touching can cause personal injury and machine damage Do not service the following parts with the power on when they are removed from their normal operating places in a machine Power supply units Pumps Blowers and fans Motor generators and similar units This practice ensures correct grounding of the units If an electrical accident occurs Use caution do not become a victim yourself Switch off the power Send the victim to get medical aid Safety information Safety inspection guide inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions As each machine was designed and built required safety items were installed to protect users and service personnel from injury This guide addresses only those items You should use good judgment to identify potentia
50. inese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Italian U K English English P N 25201768 25201767 25201766 25201765 25201764 25201763 25201762 25201761 25201760 25201759 25201758 25201757 25201756 25201814 25201813 25201812 25201811 25201810 25201809 2520 808 25201807 2520 2520 2520 806 805 804 25201803 25201802 25201801 2520 2520 800 799 25201798 25201797 25201796 25201795 25201794 25201793 25201792 25201791 25201790 25201789 25201788 25201787 25201786 CRU ID za Lenovo IdeaPad S200 S206 Miscellaneous parts Table 7 Parts list Miscellaneous parts FRU P N CRU ID System miscellaneous parts N a WINNIE DIMM Gasket ASSY S200 90200287 a WINNIE DIMM Gasket S206 90200287 b WOODY CPU THM PAD 90200312 c WINNIE CPU THM PAD ASSY S200 90200282 d WINNIE HDD Bracket ASSY S200 90200267 d WINNIE HDD Bracket S206 90200267 e WINNIE TP Battery Sponge ASSY 200 90200277 e WINNIE TP Battery Sponge S206 90200277 f WINNIE HDD Sponge ASSY S200 90200271 f WINNIE HDD Sponge S206 90200271 e g WOODY LED BD ASSY S200 90200286 g WOODY LED BD 5206 90200286 Cable miscellaneous parts N h WINNIE IO BD Cable ASSY S200 90200269 h WINNIE IO BD Cable S206 90200269 i WINNIE LED BD Cable ASSY S200 90200270 i WINNIE LED BD Cable S206 90200270
51. it in the direction shown by arrow EJ 49 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1100 Fan assembly and Heat Sink assembly For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 Figure 10 Removal steps of fan assembly and heat sink assembly Detach the fan connector in the direction shown by arrow Ef When installing Make sure that the fan connector is attached firmly to the system board Remove four screws PJ and single screw Efl Step Screw quantity Color Torque BH M2 x 2 5 mm flat head nylok coated 4 Black 1 5 kgfcm Aa M2 x 2 5 mm flat head nylok coated 1 Black 1 5 kgfcm 50 Lenovo IdeaPad 200 S206 Lift the fan assembly and heat sink assembly in the direction shown by arrow E Be careful not to damage the connector 51 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1110 Base cover speakers and power assembly For access remove these FRUs in order 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 1070 Keyboard on page 43 1080 System board on page 45 10
52. l safety hazards due to attachment of non Lenovo features or options not covered by this inspection guide If any unsafe conditions are present you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem Consider these conditions and the safety hazards they present Electrical hazards especially primary power primary voltage on the frame can cause serious or fatal electrical shock Explosive hazards such as a damaged CRT face or a bulging capacitor Mechanical hazards such as loose or missing hardware To determine whether there are any potential unsafe conditions use the following checklist at the beginning of every service task Begin the checks with the power off and the power cord disconnected Checklist 1 Check exterior covers for damage loose broken or sharp edges 2 Turn off the computer Disconnect the power cord 3 Check the power cord for a A third wire ground connector in good condition Use a meter to measure third wire ground continuity for 0 1 ohm or less between the external ground pin and the frame ground b The power cord should be the type specified in the parts list c Insulation must not be frayed or worn 4 Check for cracked or bulging batteries Remove the cover 6 Check for any obvious non Lenovo alterations Use good judgment as to the safety of any non Lenovo alterations 7 Check inside the unit for any obvious uns
53. lenovo Lenovo IdeaPad S200 S206 Hardware Maintenance Manual Note Before using this information and the product it supports be sure to read the general information under Notices on page 78 First Edition February 2012 O Copyright Lenovo 2012 All rights reserved LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclo sure is subject to restrictions set forth in Contract No GS 35F 05925 O 2012 Lenovo Contents About this manual sees iv Safety information 1 General safety Electrical safety Safety inspection guide ssssss 5 Handling devices that are sensitive to electrostatic discharge Grounding requirements Safety notices multilingual translations 7 Laser compliance statement 14 Important service information 16 Strategy for replacing FRUS 16 Strategy for replacing a hard disk CIEL A 17 Important notice for replacing a system A tutt erem ate et en pent
54. llowing is a trademark of Advanced Micro Devices Inc AMD Other company product or service names may be the trademarks or service marks of others 79
55. ment that has hazardous voltages Disconnect all power before Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine unplug the power cord If you cannot unplug it ask the customer to power off the wall box that supplies power to the machine and to lock the wall box in the off position If you need to work on a machine that has exposed electrical circuits observe the following precautions Ensure that another person familiar with the power off controls is near you Attention Another person must be there to switch off the power if necessary Use only one hand when working with powered on electrical equipment keep the other hand in your pocket or behind your back Attention An electrical shock can occur only when there is a complete circuit By observing the above rule you may prevent a current from passing through your body When using testers set the controls correctly and use the approved probe leads and accessories for that tester Stand on suitable rubber mats obtained locally if necessary to insulate you from grounds such as metal floor strips and machine frames Observe the special safety precautions when you work with very high voltages instructions for these precautions are in the safety sections of maintenance information Be extremely careful when you measure the high voltages Regularly inspect and mainta
56. r Akku entfernt und alle Verbindungskabel abgenommen sein bevor eine FRU entfernt wird AUNAN DN 335 v mud FRU 1 van NOMA WN un IWNI 1539 99 NN PMII DIAN MAN 5532 PMI 180 ADDON 152 NN MINI V ON Prima di rimuovere qualsiasi FRU spegnere il sistema scollegare dalle prese elettriche tutti i cavi di alimentazione rimuovere la batteria e poi scollegare i cavi di interconnessione FRU FEO FR ThinkPad ORE WoC 3 COS FEL VYRBOALTC HEV RIZ AYI IT eKYIZAL HEBE 7 v BALTC HEV Antes de quitar una FRU apague el sistema desenchufe todos los cables de las tomas de corriente el ctrica quite la bater a y a continuaci n desconecte cualquier cable de conexi n entre dispositivos 13 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Laser compliance statement compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD ROM drive or a DVD ROM drive Such devices are also sold separately as options If one of these drives is installed it is certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere the drive is certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products Ifa CD ROM drive a DVD ROM drive or another laser de
57. sitio y no se encuentran sueltas dentro del sistema Compru belo agitando el sistema y escuchando los posibles ruidos que provocar an Las piezas met licas pueden causar cortocircuitos el ctricos SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Safety notice 2 N DANGER Some standby batteries contain a small amount of nickel and cadmium Do not disassemble a standby battery recharge it throw it into fire or water or short circuit it Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery Certaines batteries de secours contiennent du nickel et du cadmium Ne les d montez pas ne les rechargez pas ne les exposez ni au feu ni l eau Ne les mettez pas en court circuit Pour les mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la pile de sauvegarde ou celle de l horloge temps r el veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es ad quate Une batterie ou une pile inappropri e risque de prendre feu ou d exploser Die Bereitschaftsbatterie die sich unter dem Diskettenlaufwerk befindet kann geringe Mengen Nickel und Cadmium enthalten Sie darf nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f
58. st MAIN into the jack labeled 1 the grey cable 3rd into jack labeled 3 and the white cable 2nd AUX into jack labeled 2 on the card 41 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual 1060 3G Card For access remove these FRUs in order 1010 Battery pack on page 34 Figure 6 Removal steps of 3G Card Disconnect two connectors H and remove the screw Ell Step Screw quantity Color Torque H M2 x 3 mm flat head nylok coated 1 Silver 1 5 kgfcm Remove the card in the direction shown by arrow E E 42 Lenovo IdeaPad 5200 5206 1070 Keyboard For access remove this FRU 1010 Battery pack on page 34 1030 Hard disk drive on page 37 1040 DIMM on page 39 1050 PCI Express Mini Card for wireless LAN WAN on page 40 1060 3G Card on page 42 Figure 7 Removal steps of keyboard Remove the screw Efl Step Screw quantity Color Torque H M2 x 3 mm flat head nylok coated 1 Silver 1 5 kgfcm Loosen the keyboard with fingers in the direction shown by arrow I 43 Lenovo IdeaPad S200 5206 Hardware Maintenance Manual Figure 7 Removal steps of keyboard continued Lift the keyboard a little E and then detach the connector in the direction shown by arrow EJ When installing Make sure that the FPC connector is attached firmly Lenovo IdeaPad 200 S206 1080 System board Important notices for handling the system board When handling
59. system board Related service information Related service information This chapter presents the following information Restoring the factory contents by using Recovery Disc Set on page 23 Passwords on page 24 Power management on page 25 Restoring the factory contents by using Recovery Disc Set When the hard disk drive or solid state drive is replaced because of a failure no product recovery program is on the new drive In this case you must use the Recovery Disc Set for the computer Order the Recovery Disc Set and the drive at the same time so that you can recover the new drive with the pre installed software when they arrive The Recovery Disc Set consists of the following set of DVDs to restore the computer to the original factory configuration Start Recovery Disc one disc This disc is used to format the hard disk drive and initiate the recovery process Operating System Recovery Disc one or more discs This disc restores the Microsoft Windows operating system Applications and Drivers Recovery Disc one or more discs This disc restores the pre installed applications and drivers on the computer Supplemental Recovery Disc This disc contains additional content such as software for specific models and updates to the software that was preloaded on the computer Not all recovery disc sets come with a Supplemental Recovery Disc To restore the computer to the original factory configuration using the recover
60. tery AC adapter Pre installed operating system Lenovo IdeaPad S200 Description Lenovo IdeaPad S206 External monitor connector Combo headphone jack Combo build in Microphone jack HDMI port x 1 USB 2 0 x 1 USB 3 0 x 1 2 in 1 memory card reader slot x 1 MMC SD Combo audio jack x 1 Speaker x 2 Built in microphone HDMI port x 1 only support BT amp WIFI combo module New Key Board One piece touchpad 0 3 mega pixels 2 cells 27WH Li Ion Polymer 20V Universal AC Adapter 100 240V 50 60Hz 3pin 40W with 19V DC output Windows 7 starter HP HB Meego Lenovo IdeaPad 200 S206 Status indicators The system status indicators below show the computer status 29 Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 30 Table 2 Status indicators Indicator El Power on eo E Battery Meaning On solid white The computer is powered on Blinking The computer is in sleep mode off The computer is powered off On solid white The battery has more than 20 charge Solid amber The battery has between 5 and 20 charge Fast blinking amber The battery has less than 5 charge Slow blinking amber The battery is being charged When battery charge reaches 20 the blinking color changes to white Slow blinking white The battery has between 20 and 80 charge and is still charging When the battery reaches 80 charge the light will stop blinking but charging will continue until the battery is
61. these patents LENOVO GROUP LTD PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product specifications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate wit
62. tte eject button Fuses blown by attachment of a nonsupported device Forgotten computer password making the computer unusable Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities Missing parts might be a symptom of unauthorized service or modification If the spindle of a hard disk drive becomes noisy it may have been subjected to excessive force or dropped General checkout Power system checkout system checkout To verify a symptom follow the steps below Turn off the computer Remove the battery pack Connect the AC adapter Make sure that power is supplied when you turn on the computer Turn off the computer Disconnect the AC adapter and install the charged battery pack Make sure that the battery pack supplies power when you turn on the computer SE E If you suspect a power problem see the appropriate one of the following power supply checkouts Checking the AC adapter on page 21 Checking operational charging on page 21 Checking the battery pack on page 22 Checking the AC adapter You are here because the computer fails only when the AC adapter is used If the power on indicator does not turn on check the power cord of the AC adapter for correct continuity and installation If the computer does not charge during operation go to Checking operation
63. ty The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration Attention If the SVP has been forgotten and cannot be made available to the servicer there is no service procedure to reset the password The system board must be replaced for a scheduled fee Related service information Power management management Note Power management modes are not supported for APM operating system To reduce power consumption the computer has three power management modes screen blank sleep standby and hibernation Screen blank state If the time set on the Turn off monitor timer in the operating system expires the LCD backlight turns off You can also turn off the LCD backlight by pressing To end screen blank state and resume normal operation press E Sleep standby state When the computer enters sleep standby state the following events occur in addition to what occurs in screen blank state The LCD is powered off The hard disk drive is powered off The CPU stops Putting your computer into sleep state If you will be away from your computer for only a short time put the computer into sleep state When the computer is in sleep state you can quickly wake it to resume use and bypass the startup process To put the computer into sleep state click and select Sleep from the Start menu To wake the computer do one of the following Press the power button
64. ungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Italian U K English English Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German P N 25201694 25201693 25201692 25201691 25201690 25201689 25201688 25201687 25201686 25201685 25201684 25201683 25201682 25201681 25201680 25201679 25201678 25201677 25201676 25201675 25201674 25201673 25201672 25201671 25201670 25201669 25201668 25201667 25201666 25201784 25201783 25201782 25201781 25201780 25201779 25201778 25201777 25201776 25201775 25201774 25201773 25201772 25201771 25201770 25201769 CRU ID za 71 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual Table 6 Parts list Keyboard continued Language Dafon black continued 5200 8206 continued Dafon white 72 French Russian Traditional Chinese Korean Canadian English amp French Latin Portuguese Thai Turkish Spanish Italian U K English English Bulgarian Czechoslovakian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Ch
65. vice is installed note the following ZAN CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure O uso de controles ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposi o radia o NARRAN WE Ch HERA GR Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites Werden Steuer und Einstellelemente anders als hier festgesetzt verwendet kann gefahrliche Laserstrahlung auftreten Az itt el rt elj r sokt l be ll t sokt l s vez rl sekt l elt rni a l zersug rz s vesz lye miatt kock zatos L utilizzo di controlli regolazioni o l esecuzione di procedure diverse da quelle specificate possono provocare l esposizione a Ucnonb30BaHue anemenTOB Hacrpoliku n BbINMONHEHMe MPOUEAYP UHbIX HEM yKa3aHO 3DECb MOXET MPUBECTU K ONACHOMY pannaunoHHOMy O NyyeHnto Pouzitie kontr l prav alebo inych vykonani od inych vyrobcov ako je v tomto Specifikovan mohlo by mat za n sledok nebezpe enstvo vystavenia sa vyZiarovaniu beet EE UF 360 BUR OPE DO XE El uso de controles o ajustes o la ejecuci n de procedimientos distintos de los aqu especificados puede provocar la exposici n a radiaciones peligrosas Opening the CD ROM drive the DVD R
66. wear jewelry chains metal frame eyeglasses or metal fasteners for your clothing Attention Metal objects are good electrical conductors Wear safety glasses when you are hammering drilling soldering cutting wire attaching springs using solvents or working in any other conditions that may be hazardous to your eyes After service reinstall all safety shields guards labels and ground wires Replace any safety device that is worn or defective Reinstall all covers correctly before returning the machine to the customer Fan louvers on the machine help to prevent the overheating of internal components Do not obstruct fan louvers or cover them with labels or stickers Safety information Electrical safety safety Observe the following rules when working on electrical equipments Important Use only approved tools and test equipments Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges Do not use such kind of mat to protect yourself from electrical shock Find the room emergency power off EPO switch disconnecting switch or electrical outlet If an electrical accident occurs you can then operate the switch or unplug the power cord quickly Do not work alone under hazardous conditions or near the equip
67. y disc set do the following 1 Insert the bootable Start Recovery Disc into the optical drive 2 Startthe computer When the Lenovo logo comes up immediately press F12 on the boot sequence menu select the optical drive as the first boot up device The computer will boot from the Start Recovery Disc Follow the on screen instructions to begin the recovery process 3 Read the license If you agree with the terms select I accept these terms and conditions and then click Next 4 Insertthe Operating System Recovery Disc when prompted and click Yes to begin the operating system recovery process 5 Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the applications and drivers recovery process 6 If you have a Supplemental Recovery Disc insert it when prompted and click Yes If you do not have a Supplemental Recovery Disc click No 23 SM Lenovo IdeaPad 5200 5206 Hardware Maintenance Manual 7 When all of the data has been copied from the last disc in the set remove the disc and restart the computer Note The remainder of the recovery process is fully automated and no action is required by you The computer will restart into the Windows desktop several times and you might experience periods when no activity is apparent on the screen for several minutes at a time This is normal 8 When the recovery process is complete the Welcome to the Microsoft Windows screen is displayed Follow

Lenovo Laptop S200 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents