Lenovo 04N7323 User's Manual
Contents
1. A12 S Troubleshooting Symptom The power LED is amber Possible causes a Display power management mode There is no sync signal The signal cable is not fastened securely Check the computer power and graphics adapters configuration The frequency of the sync input is outside the operating range of the monitor HORZ 30kHz 49kHz VERT 50Hz 90Hz Symptom The image on the SCREEN is not centered or too small or not a rectangle shape Possible Causes Image adjustment not been done yet in the current operating mode Use the SELECT and buttons to set the image to your liking Symptom The monitor doesn t enter the power saving off mode Amber led Possible Causes Computer video signal is not VESA DPMS standard Enter the PC or the video controller card is not using the VESA DPMS power management function A12 3828TU0032A 199 5 311 35PM A13 S Further help If you are unable to correct the problem yourself you may seek further help as follows Call IBM HELPCENTER In the US call 1 800 772 2227 In Canada call 1 800 565 3344 In other countries contact your dealer retailer or other IBM authorized servicer Before calling please have available as much of the following information as possible 1 Type model and serial number from the label on the back of your monitor Purchase receipt Description of problem Computer type and model System configuration hardware fitted etc System BIOS v2. Monitor Choose a suitable place to position the monitor where it is not near fluorescent desk lighting or any equipment that produces magnetic fields that could cause interference Ensure that the furniture or equipment can support the weight of the monitor Allow at least 2 inches 50mm ventilation space around the monitor Height The monitor should be positioned so that the top of the screen is slightly below your eye level when you sit at your workstation Orientation Choose a position that gives the least reflection from lights and windows usually at a right angle to any windows The monitor should be positioned directly in front of you so that you do not have to twist your body Tilt the monitor to a comfortable viewing angle A1 3828TU0032A 199 5 311 34PM A2 S Precautions Working Practices Rest Take regular breaks Vary your posture and stand up and stretch occasionally as prolonged use of computer workstations can be tiring Back You should sit back in the chair and use the back rest Hands Use a light touch on the keyboard keeping your hands and fingers relaxed Allow a space in front of the keyboard to rest your wrists when not typing Consider using a wristpad Eyesight Working with monitors in common with any prolonged close work can be visually demanding Look away from the screen periodically and have your eyesight checked regularly Screen settings Set the screen brightness and contrast to a comf
3. S Use a cord set with a grounding type attachment plug rated 13 amperes minimum 250 volts The cord set should be marked lt HAR gt and have the appropriate safety approvals for the country in which the equipment will be installed cen EPA POLLUTION PREVENTER As an ENERGY STAR Partner IBM Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency A18 3828TU0032A 199 5 311 35PM A19 p Compliances MPR Il This product complies with Swedish National Council for Metrology MPR standards issued in December 1990 MPR II for very low frequency VLF and extremely low frequency ELF European Union EU Statement This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 European Standard EN 55022 The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices Properly shielded and grounded cables and connectors must be used in order to reduce the potential for causing interference to radio and TV communications and to other electrical or electronic equipment Such cables and connectors are available from IBM authorized dealers In accordance with EN 50082 1 1992 Performance Criterion A it should be noted that in the presence of certain electromagnetic fields some screen jitter may be observed
4. Service Information The following parts are for use by IBM service or IBM authorized dealers to support customer warranty Parts are for service use only Model Type 2268 Part Number M T Model Description 04N7322 2268 06E Monitor UVNH pearl white 04N7323 2268 46E Monitor UVNH stealth black A19 3828TU0032A 199 5 311 35PM A20 S Warranty Statement of Limited Warranty The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use and not for resale from IBM or your reseller The term Machine means an IBM machine its features conversions upgrades elements or accessories or any combination of them Unless IBM specifies otherwise the following warranties apply only in the country where you acquire the Machine If you have any questions contact IBM or your reseller Machine A40 M T 2268 Warranty Period Three years Contact your place of purchase for warranty service information Production Status Each Machine is manufactured from new parts or new and used parts In some cases the Machine may not be new and may have been previously installed Regardless of the Machine s production status IBM s warranty terms apply The IBM Warranty for Machines IBM warrants that each Machine 1 is free from defects in materials and workmanship and 2 conforms to IBM s Official Published Specifications The warranty period for a Ma
5. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult an IBM authorized dealer or service representative for help Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits Proper cables and connectors are available from IBM authorized dealers IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this devic
6. 3828TUO032A 199 5 311 34PM i S Edition 1 This publication could contain technical inaccuracies or typographical errors Changes are made periodically to the information herein these changes will be made in later editions IBM may make improvements and or changes in the product s and or programs s at any time It is possible that this publication may contain reference to or information about IBM products machines and programs programming or services that are not announced in your country Requests for copies of this publication and for technical information about IBM products should be made to your IBM Authorized Dealer or IBM Retailer No part of this publication may be reproduced or distributed in any form or by any means without prior permission in writing from the International Business Machines Corporation References in this publication to IBM products programs or services do not imply that IBM intends to make these available in all countries in which IBM operates Any reference to an IBM product program or service is not intended to state or imply that only IBM s product program or service may be used Any functionally equivalent product program or service that does not infringe any of IBM s intellectual property rights or other legally protectable rights may be used instead of the IBM product program or service Evaluation and verification of operation in conjunction with other products programs or services
7. Ea 3828TU0032A 199 5 311 35PM A8 S Image Control Panel Image Control Icons Listed below are the icons icon names and icon descriptions of the items icon Description Ci Horizontal To move picture image left and right Position Moves the screen image left Moves the screen image right Horizontal To adjust image width Size Decreases the size of the screen image Increases the size of the screen image Vertical To move image up and down Position Moves the screen image down Moves the screen image up Vertical To adjust image height Size Decreases the size of the screen image Increases the size of the screen image Side To correct the bowing in and out of the image Pincushion Curves the image s edges inwards Curves the image s edges outwards Trapezoid To correct geometric distortion Makes the screen image narrower at the top Moves the screen image wider at the top Recall Function When the user wants to recall one of the 5 factory fixed image modes push the and buttons simultaneously To recall the next image mode press both the and buttons again A8 3828TU0032A 199 5 311 35PM AQ S Power Management System When used in conjunction with a PC having power saving circuitry or a PC running screen blanking software this monitor automatically reduces its power consumption when the computer is not in u
8. OD NO WARRANTIES APPLY AFTER THAT PERIOD Limitation of Liability Circumstances may arise where because of a default on IBM s part or other liability you are entitled to recover damages from IBM In each such instance regardless of the basis on which you are entitled to claim damages from IBM including fundamental breach negligence misrepresentation or other contract or tort claim IBM is liable only for 1 damages for bodily injury including death and damage to real property and tangible personal property and 2 the amount of any other actual direct damages or loss up to the greater of U S 100 000 or the charges if recurring 12 months charges apply for the Machine that is the subject of the claim UNDER NO CIRCUMSTANCES IS IBM LIABLE FOR ANY OF THE FOLLOWING 1 THIRD PARTY CLAIMS AGAINST YOU FOR LOSSES OR DAMAGES OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE 2 LOSS OF OR DAMAGE TO YOUR RECORDS OR DATA OR 3 SPECIAL INCIDENTAL OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES INCLUDING LOST PROFITS OR SAVINGS EVEN IF IBM OR YOUR RESELLER IS INFORMED OF THEIR POSSIBILITY SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU
9. caution always unplug the monitor before cleaning it A3 3828TU0032A 199 5 311 34PM A4 S Tilt Swivel Base Turn Off the equipment and all attached options Carefully set the monitor face down with the underside facing you Installation 1 Align the hooks on the tilt swivel stand with the matching slots in the base of the monitor 2 Insert the hooks into slots 3 Slide the tilt swivel stand toward the front of the monitor until the latches click into the locked position A4 3828TU0032A 199 5 311 34PM AS S Installation The supply voltage is marked on the ID label located on the rear panel of the monitor If your local voltage is different do not use the monitor and contact your supplier before using the display Connections To connect your monitor after the video adapter is properly installed 1 Turn OFF the power to your computer and all its attached options 2 Position the monitor and the computer so that you can easily get to the back panel of each 3 Connect the signal cable with D sub connector to the graphics board on your PC as described in your PC Owner s Manual 4 Tighten the screws on the video cable connectors to keep them from coming loose and to prevent radio and TV interference o Connect the power cord to the AC receptacle on the back of the monitor Plug
10. chine is a specified fixed period commencing on its Date of Installation The date on your receipt is the Date of Installation unless IBM or your reseller informs you otherwise During the warranty period IBM or your reseller if authorized by IBM will provide warranty service under the type of service designated for the Machine and will manage and install engineering changes that apply to the Machine For IBM or your reseller to provide warranty service for a feature conversion or upgrade IBM or your reseller may require that the Machine on which it is installed be 1 for certain Machines the designated serial numbered Machine and 2 at an engineering change level compatible with the feature conversion or upgrade Many of these transactions involve the removal of parts and their return to IBM You represent that all removed parts are genuine and unaltered A part that replaces a removed part will assume the warranty service status of the replaced part If a Machine does not function as warranted during the warranty period IBM or your reseller will repair it or replace it with one that is at least functionally equivalent without charge The replacement may not be new but will be in good working order If IBM or your reseller is unable to repair or replace the Machine you may return it to your place of purchase and your money will be refunded If you transfer a Machine to another user warranty service is available to that user for the rema
11. e must accept any interference received including interference that may cause undesired operation Industry Canada Compliance Statement This Class B digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil numerique de la Classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada A17 3828TU0032A 199 5 311 35PM A18 S Compliances Power Cord For your safety IBM provides a power cord with a grounded attachment plug to use with this IBM product To avoid electrical shock always use the power cord and plug with a properly grounded power outlet IBM power cords used in the United States and Canada are listed by the Underwriters Laboratories UL and certified by the Canadian Standards Association CSA For units intended to be operated at 115 volts Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG type SVT or SJT three conductor cord a maximum of 4 5 metres 15 feet in length and a parallel blade grounding type attachment plug rated 15 amperes 125 volts For units intended to be operated at 230 volts U S use Use a UL listed and CSA certified cord set consisting of a minimum 18 AWG type SVT or SJT three conductor cord a maximum of 4 5 metres 15 feet in length and a tandem blade grounding type attachment plug rated 15 amperes 250 volts For units intended to be operated at 230 volts outside the U
12. ersion number Operating System and version number Display driver version number CONDOR OW P If possible stay by your computer system Your technical support representative might want to go through the problem with you during the call A13 3828TU0032A 199 5 311 35PM A14 S Service 1 Unplug the monitor from the wall outlet and refer servicing to alified service personnel when N The power cord or plug is damaged or frayed Liquid has been spilled into the monitor The monitor has been exposed to rain or water The monitor does not operate normally following the operating instructions Adjust only those controls that are covered in the operating instructions An improper adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore the monitor to normal operation The monitor has been dropped or the cabinet has been damaged The monitor exhibits a distinct change in performance Snapping or popping from the monitor is continuous or frequent while the monitor is operating It is normal for some monitors to make occasional sounds when being turned on or off or switching video modes Do not attempt to service the monitor yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel A14 3828TUO032A 199 5 311 35PM A15 S Specifications Sync Signal type Type H
13. except those expressly designated by IBM are the user s responsibility IBM may have patents or pending patent applications covering subject matter in this document The furnishing of this document does not give you any license to these patents Trademarks The following terms used in this publication are trademarks or service marks of the IBM Corporation in the United States or other countries ENERGY STAR is a U S registered mark Copyright International Business Machines Corporation 1999 All rights reserved 3828TU0032A 199 5 311 34PM it S Packing List The product package should include the following items 1 Monitor 2 Owner s Manual 3 Power Cord 4 Swivel Base 5 Diskette 3828TU0032A 199 5 311 34PM iti S Table of Contents Precautions Workplace preparation cceeesceeeseeeeeneeeeeneeeeeaeeeeeaaeeseeeeessaeeeesnneeseaees Al Working Practices i iiciicavci tian neil dti ee A2 Tilt Swivel Base INSPAN AION ae ove veces vageecaveacaccteecesveveies cose sia rocedegyevecucesaads baeedeeee A4 Installation CONNECCION Sin WE cee Le isin ted A5 Location and Function of Controls Front VIEW dinne ene e lesbo nA en ee eee ed A6 PROAN MIQW vances ect lscsccnisciectadeets ahaa ave ceacndnsct cctizasdetcietet ages A ceataandeteasede A6 Image Control Panel c cccccececceeeceeeeeeeeeeeeeeeeeeeeetetieeeeeeeeeteeneeees A7 Power Management System MPR Il and DDC Power Management SyS
14. inder of the warranty period You should give your proof of purchase and this Statement to that user However for Machines which have a life time warranty this warranty is not transferable Warranty Service To obtain warranty service for the Machine you should contact your reseller or call IBM In the United States call IBM at 1 800 772 2227 In Canada call IBM at 1 800 565 3344 You may be required to present proof of purchase IBM or your reseller will provide certain types of repair and exchange service either at your location or at IBM s or your reseller s service center to restore a Machine to good working order 3828TU0032A 199 5 311 35PM A21 S Warranty When a type of service involves the exchange of a Machine or part the item IBM or your reseller replaces becomes its property and the replacement becomes yours You represent that all removed items are genuine and unaltered The replacement may not be new but will be in good working order and at least functionally equivalent to the item replaced The replacement assumes the warranty service status of the replaced item Before IBM or your reseller exchanges a Machine or part you agree to remove all features parts options alterations and attachments not under warranty service You also agree to ensure that the Machine is free of any legal obligations or restrictions that prevent its exchange You agree to 1 obtain authorization from the owner to have IBM or your re
15. ortable level You may have to adjust this as the lighting changes during the day Many application programs let you select color combinations which can help you to view in comfort A2 3828TU0032A 199 5 311 34PM A3 p Precautions Power Source 1 Make sure the power cord is the correct type that required in your area 2 This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required 3 Connect the power cord into your monitor s power input socket and then plug the other end into a 3 pin AC power outlet The power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your monitor Power cord For safe operation use the power cord supplied with the unit Notes Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor To keep the monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety pre
16. r with the controls you are ready to operate the monitor 1 Turn on the monitor PC and other peripherals you plan to use 2 After the PC has booted powered up and finished self testing enter a software application that uses the full screen display 3 While looking at the image on the screen adjust the controls for the image size centering brightness and contrast levels you prefer 4 This monitor is an auto scanning monitor capable of synchronizing with a variety of video standards automatically The Scanning Mode Table below indicates the resolution as well as the horizontal and vertical refresh rates of some of the modes that this monitor can match to the output of your PC s graphics card Other resolutions and standards can also be synchronized and displays on this monitor as long as they are within the horizontal and vertical frequency range of this monitor See the specifications for this information A10 3828TU0O032A 199 5 311 35PM All E Video Memory Modes Factory Preset Timing Signal Chart Video Sync Polarity Frequency Total Period Data Period Blanking Front Porch Pulse Width PrPrPHZON TDOTL Back Porch Polarity Frequency Total Period Data Period Blanking Front Porch Vv E R T l c A L Pulse Width Back Porch Resolution Recall A11 3828TU0032A 199 5 311 35PM
17. se The monitor has power saving states indicated by the light emitting diode LED on the front panel These power saving states exceed the Environmental Protection Agency EPA Energy Star requirements using the methodology for Display Power Management Signals DPMS Developed by the Video Electronics Standards Association VESA Low Radiation Compliance MPR Il This monitor meets one of the strictest guidelines available today for low radiation emissions offering the user extra shielding and an anti static screen coating These guidelines set forth by a government agency in Sweden limits the amount of emission allowed in the Extremely Low Frequency ELF and Very Low Frequency VLF electromagnetic range DDC Display Data Channel DDC is a communication channel over which the monitor automatically informs the host system PC about its capabilities This monitor has DDC function DDC2B carry out uni directional communication between PC and monitor Under these situations the PC sends display data to the monitor but not commands to control the monitor servings NOTE PC must support DDC functions to do this Some older computer systems are not compatible with the DDC standard If your monitor is displaying a monochrome image or the wrong resolution need to change with a DDC compatible VGA card A9 3828TU0032A 199 5 311 35PM A10 S General Operation After following the installation instructions and getting familia
18. seller service a Machine that you do not own and 2 where applicable before service is provided a follow the problem determination problem analysis and service request procedures that IBM or your reseller provide b secure all programs data and funds contained in a Machine and c inform IBM or your reseller of changes in a Machine s location IBM is responsible for loss of or damage to your Machine while it is 1 in IBM s possession or 2 in transit in those cases where IBM is responsible for the transportation charges Extent of Warranty IBM does not warrant uninterrupted or error free operation of a Machine The warranties may be voided by misuse accident modification unsuitable physical or operating environment improper maintenance by you removal or alteration of Machine or parts identification labels or failure caused by a product for which IBM is not responsible THESE WARRANTIES REPLACE ALL OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF EXPRESS OR IMPLIED WARRANTIES SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU IN THAT EVENT SUCH WARRANTIES ARE LIMITED IN DURATION TO THE WARRANTY PERI
19. sync V sync Separate sync H sync V sync Signal Connector Pin Assignment Pin Separate Sync 1 Red 2 Green 3 Blue 4 Ground 5 Self Test 6 Red Ground 7 Green Ground 8 Blue Ground 9 NC 10 Ground 11 Ground 12 SDA 13 Horiz Sync 14 Vert Sync 15 SCL A15 3828TUO032A 199 5 311 35PM A16 S Specifications Picture tube 14 inch 13 2 inches viewable Tinted 90 degree deflection 0 28 mm Non Glare screen Horizontal Frequency 30 49 kHz Vertical Frequency 50 90 Hz Display Area 260 x 190 mm H x V Video Bandwidth 65 MHz Resolution 1024 x 768 Non Interlace 60Hz Refresh Rate Signal connector 15 pin D Sub type Power input AC 100 240V 50 60Hz 1 5A Power Consumption Table MODE H sync V sync Video Cae pion LED Color Normal On On On lt 85W Green Stand by Off On Off lt 15W Amber Suspend On Off Off lt 15W Amber Off Off Off Off lt 8W Amber Dimensions 352 x 397 1 x 307 5 mm With Tilt Swivel Stand WXDXH 13 9 x 15 6 x 12 1 inch Weight net 10 5 kg 23 15 Ibs A16 3828TU0032A 199 5 311 35PM A17 S Compliances Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation
20. tem csccecccseseeeeeeteneeeeeeeeeeseeeeeaeeseeeeeeeseeeesas A9 Low Radiation Compliance MPR Il sssesessseseesiseeesrerinerrerreernerrsrreernene A9 DDC Display Data Channel ecceeecceeseeeeeeeeneeeeeeeeeeeseeeeeaeeseeeseeeseaeeas AQ General Operation ccccccecccececcececeeeseseeeeeeeeeeeceeeeseteceeeeeetseeeeeeeas A10 Video Memory Modes Factory Preset Timing Signal Chart ccccesceeseeeeeeeeeeeeeeeteeeeeteerenees A11 Troubleshooting 0 cee eececeeeeceeeeceeeeeeeeeseeeeeeeeeaeeeeeesareesasersasereatereaeenens A12 Further Help cesars a A13 AO E E EAA EEES TEATEET A14 Specifications e a rr r a a aa A15 Compliance 222002265 28 ep i ie ee ee ee A17 Wattah ynsan a aan lied See back of manual iii 3828TU0032A 199 5 311 34PM Al S Precautions A Danger To avoid shock hazard Do not remove the covers Do not operate this product unless the stand is attached Do not connect or disconnect this product during an electrical storm The power cord plug must be connected to a properly wired and grounded power outlet Any equipment to which this product will be attached must also be connected to properly wired and grounded power outlets To isolate the monitor from the electrical supply you must remove the plug from the power outlet The power outlet should be easily accessible Handling e Your color monitor is heavy so handle it with care Workplace preparation Positioning the
21. the other end of the power cord into a properly grounded electrical outlet The socket outlet should be installed near the equipment and should be easily accessible o gt A5 3828TUO032A 199 5 311 34PM A6 S Location and Function of Controls Front View eee aoa A SS 4 Power On Off Button Power Indicator Image Control Panel Brightness Contrast Rear View ID Label AC Power Connector Signal Cable A6 3828TU0032A 199 5 311 34PM A7 S Location and Function of Controls Power On Off Button This Button is used to turn the power On or Off o Power Indicator The power indicator lights when the power is On and indicates the operating status of the display O Contrast Adjust the display to the contrast desired Move the thumbwheel located beneath this indicator to increase or decrease the display contrast X Brightness Used to adjust the brightness of the screen Move the thumbwheel located beneath this indicator to increase or decrease the display brightness oe of of oD oA aa Image Selection and Adjustment buttons Use either the lt or button to select the icons which you wish to adjust and display _ buttons Used to set digital values for each of the select on screen control item by pressing button for increment or button for decrement A7
Download Pdf Manuals
Related Search