Kuppersbusch USA EKV 6800.0 M User's Manual
Contents
1. 0 0 ee ee 21 General Connection and operation Safety Operation Before using the appliance for the first time 22 Mains voltage Disposing of the packaging material and your old appliance Initial cleaning Initial Operation 1 ee es 22 Filling the appliance Switching on the appliance Foam consistency and amount of foam Milk temperature Making CONGO 545 544 44 o4 arrangieren 23 Electronic push buttons Height adjustable coffee dispenser Switching on the appliance Making espresso and coffee creme Making coffee Making cappuccino Making decaffeinated coffee Dispensing hot water Cleaning and Care cc nennen 25 Casing Water tank Work area Cleaning agents Preparation Automatic cleaning Automatic decalcification Decalcifying appliances connected to the tap water supply Restarting an interrupted wash Cleaning the milk frother and the coffee dispensers Programin una er nern 27 Accessing the programming device Cumulative Total Button assignment Product name Quantity of water Grinding time Milk dispensing time Pre brewing Tamping Coffee grounds number Warning Time to clean the milk frother Warning Time to clean the brewing unit Brewing unit setting Grinder calibration Grinder setting Coffee temperature Steam temperature Warning Time to decalcify Exiting the programming system Special functions 222 o onen nenn nn 30 Resetting the water quantity metre Resetting the washing2. electric data Functioning at tensions outside this range is therefore not container Any other kind of cof Tr guaranteed fee e g coffee which has al LT ready been ground will damage N ave U The appliance was developed and produced in compliance with the COMPANY the grinder o QUALITY SYSTEM UNI EN ISO 9001 Disassembly A Should the coffee machine need to be removed from its seat it must firstly be disconnected from the power supply by pulling out the plug Press the respective engaging points on the guides and remove the appliance supporting it from below 33 K PPERSBUSCH HAUSGER TE AG Postfach 10 01 32 D 45801 Gelsenkirchen K ppersbuschstr 16 D 45883 Gelsenkirchen Telefon 02 09 4 01 0 Telefax 02 09 4 01 3 03 www kueppersbusch de K ppersbusch Ges m b H Eitnergasse 13 1231 Wien Telefon 01 8 66 80 0 Telefax 01 8 66 80 72 www kueppersbusch at e Mail verkauf kueppersbusch at Kuppersbusch ALLERFEINSTE KUCHENTECHNIK
3. cycles Resetting to standard parameters What to do if trouble occurs 2 22 0 00a eee 31 Installation instructions for professional fitters 32 Instructions for fitting Installation dimensions EKV 6800 0 Installation Technical data 2 22 moon nennen nn 33 Your appliance at a glance Milk container drawer Milk flow adjustor tap 1 2 3 Control panel 4 Decaffeinated coffee powder drawer 5 Water tank not for appliances attached to the tap water supply 6 Coffee bean container 7 Clear text display 8 Coffee grounds bowl 9 Pull out compartment for cups 10 Front panel release 11 Drip grid 12 Light switch 13 ON OFF switch 14 Coffee dispenser 15 Hot water dispenser 16 Milk suction tube Panel flap micro switch Brewing unit flap opened Milk frother air adjustor Brewing unit Tube for transporting ground coffee Nameplate Milk frother with pipes CO N OD o A WD N Panel flap opened 20 EKV 6800 0M Fittings and general characteristics Your new built in fully automatic coffee machine EKV 6800 0 has all of the functions of a coffee machine for professional use just like you get in your favourite coffee bar The coffee is freshly ground for each cup of coffee and is transported into a brewing unit Once the pump has forced the water through the coffee the coffee grounds are automatically knocked out of the unit Thanks to fully automatic micro processor controls the clear text displa
4. fill in roasted coffee beans Do not fill right up to the maximum level in order to still be able to close the lid ce Use whole commercially available coffee beans Attention Only pour coffee beans into this container Any other kind of coffee e g coffee which has already been ground will damage the grinder If you wish to make milk drinks Pull out the milk drawer in the front part of the appliance Open the milk box and position it inside the drawer Insert the milk suction tube into the opening ce You can use a 0 5 litre or a 1 litre milk box c Please use commercially available long life milk with a fat content of 3 5 or fresh milk switching on the appliance Press the ON OFF switch red flip switch on the inside below the control panel in order to switch on the appliance The machine commences with a self diagnosis cycle which may take up to three minutes when the machine is cold During this procedure the display will indicate Please wait Heating On Off switch Light switch At the end of this self diagnosis cycle the display will indicate Select product gt lf an error is indicated after the self diagnosis has been carried out consult the chapter on What to do if trouble occurs or perhaps you may need to contact customer service gt The appliance is fitted with a safety system which will stop the appliance if the pump operates consistently for approximat
5. new settings will have been stored 21 Quantity of water The amount of water to be dispensed for each individual drink is programmed If you wish to change the quantity of water for one or more drinks proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 and 4 4 to go through the various sub menus until the display indicates Water volume Press the ENTER button again to scroll through the various previously set drinks Press the CURSOR buttons 2 w and 4 to increase or decrease the quantity of water used for each individual drink When you have selected a quantity of water press the ENTER button again to confirm this setting and proceed with entering the quantity of water of the drink for the next button After the setting has been adjusted press the RESET button 3 to exit the sub menu and return to the main menu The new settings will have been stored Grinding time A grinding time in seconds is programmed for each individual drink The grinding time determines the coffee quantity used to make the respective drink If you wish to change the grinding time for the individual drinks proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 and 4 4 to scroll through the various sub menus until the display indicates Grinding time Press the ENTER button again to go through the grinding times in
6. seconds for the individual previously set drinks Example for espresso button assignment Grinding time s 1 Espresso 0005 0 Press the CURSOR buttons 2 w and 4 4 to raise or lower the grinding time for the individual drinks When you have selected a grinding time press the ENTER button again to confirm this setting and proceed with entering the grinding time of the drink for the next button After the setting has been adjusted press the RESET button 3 to exit the sub menu and return to the main menu The new settings will have been stored 28 Milk dispensing time For all milk drinks buttons 4 6 and 8 the milk dispensing duration is programmed in seconds Proceed as follows to adjust the dispensing time Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Milk time Press the ENTER button again to go through each individual previously set drink in accordance with the button assignment 4 6 and 8 Press the CURSOR buttons 4 and 2 to increase decrease the milk dispensing time Once you have changed the time press the ENTER button again to confirm the setting and proceed to enter the milk dispensing time of the drink for the next button After making the adjustment press the RESET button 3 to exit the sub menu and return to the previous menu item The new setting will have been S
7. the RESET button 3 to exit the sub menu and return to the main menu The new settings will have been stored Button assignment Product name A drink is allocated to every single button n indicates the number of the relative key The buttons have been assigned in the factory You can however allocate other beverages to the buttons according to your personal taste An individually programmed button assignment always overlays the one pre set in the factory and affects all of the following program steps Proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to go through the various sub menus until the display indicates Product name n Press the ENTER button again to access the button assignment for button 1 Product name 1 n 1 Press the CURSOR buttons 2 and 4 to allocate the various beverages available in the list to this particular button Once you have selected a drink press the ENTER button again to confirm that this drink is to be allocated to this button and proceed with the selec tion of a beverage for the following button The following buttons are programmable in sequence a gt Buttons 1 2 and 3 can only be set for coffee drinks buttons 4 6 and 8 can be set for both coffee and milk drinks After the adjustment has been made press the RESET button 3 in order to exit the sub menu and return to the main menu The
8. the coffee dispensers on page 26 Automatic cleaning Take a cloth and carry out the washing procedure as follows Open the cover of the coffee powder container decaffeinated coffee and put in a detergent tab Close the cover Pull out the left drawer Pour approx 0 5 litres of water and approx 20 ml of liquid detergent into a suitable vessel and place it in the milk box compartment as shown in the illustration Insert the milk suction tube Place a suitable vessel with a capacity of approx 1 5 2 litres to collect the deter gent liquid dispensed 29 Press the button for decaffeinat ed coffee and keep it pressed until Clean Insert Cleaner appears in the display Now press the button for decaffeinated coffee again in order to start the rinsing cycle immediately If the button for decaffeinated coffee is not pressed the machine will auto matically commence with the rinsing cycle after about 20 seconds During the entire cleaning procedure all of the coffee dispensing buttons will be disabled and the display will show Rinse As soon as the vessel with the detergent liquid has been emptied through the milk suction tube take it out of the drawer fill in 1 litre of clean water and place it into the left drawer again with the milk suction hose inserted The rinsing cycle will commence automatically after the cleaning program The clean water will be drawn into the cycle The di
9. 8 kW ing the guides on the appliance into those previously inserted into the unit The machine should glide on the rails when slight pressure is applied to the Connection cable 4 foot front of the coffee machine If this is not the case the distance between Appliance dimensions WxDxH 191 2 x 1411 64 x 1515 64 the guides has to be checked again Niche dimensions WxDxH 83 8 x 183 64 x 14314 While he appliance Is being in Net weight 115 Ibs serted it will automatically engage Bias 139 into the respective engaging J i points A in the guides Fresh water capacity 1 35 gallons Classification of the control devices according to protection against electric shocks Classified in class appliances Control device pollution Suitable for use in a setting of standard or normal pollution Category protection against excess tension Category Software class and structure Class A Plugboard of control unit 100 x 80 mm Open the cover on top remove the Coffee powder The plugboard is constructed for use in the temperature range indicated in water tank and fill up the appli decaffeinated coffee the electric data The logical components comprising the control unit are ance as shown on the illustration not intended for use at higher temperatures and this could result in malfunctioning Attention nn The plugboard is constructed for use in the voltage range indicated in the Only pour coffee beans into this
10. INSTRUCTION MANUAL with installation instructions Please Note page numbers are not consecutive because those containing other than English language have been removed 927584 L91 Kuppersbusch For your information Please read this manual carefully before using your coffee machine for the first time It contains Important safety advice it explains how to use and look after your appliance so that it will provide you with many years of reliable service If a fault develops with your appliance please consult the chapter on What to do if trouble occurs You can often rectify minor problems yourself without having to call in a service technician Please keep this manual in a safe place and pass it on to new owners for their information and safety The following symbols are used in this operating manual The warning triangle warns of possible health hazards It also warns of a risk of damage to the appliance amp gt Here you will find useful hints and tips Safety instructions Caution People who are not yet familiar with the coffee machine may only operate it under supervision Children are frequently not able to recognise risks involved on handling the appliance Please ensure that they are supervised accordingly and never allow them to play with the appliance Contents Your appliance ata glance 0 00 ce eee ees 20 Fittings and general characteristics 000005 21 Safety instructions
11. ater supply For appliances connected to the tap water supply a decalcifying filter must be installed in front of the water connection at the top of the appliance Restarting an interrupted wash If the cleaning and decalcifying program is discontinued because of a power cut or because the appliance is switched off the brewing unit will be set at an interval when the appliance is switched on again and the display will show Please wait Heating Press the button in order to repeat the cleaning or decalcifying program as already described Cleaning the milk frother and the coffee dispensers For dispensing cappuccino instantly the machine is equipped with a milk frother inserted directly into the coffee dispenser A Check that the milk suction tube is not bent or blocked Clean as follows Open the front panel flap and then the brewing unit flap Carefully pull the entire brewing unit towards you do not pull it downwards and remove it Pull the milk frother upwards and remove it from the brewing unit Remove all of the pipes connected Dismantle the milk frother into three parts and rinse carefully under running water Pull out the coffee dispenser and rinse under running water too In order to re install proceed in reverse order observing the connection of the milk frother tubes red tube top connection piece white tube middle connection piece blue tube bottom connectio
12. c plug from the socket by pulling on the cable m When carrying out repairs and replacing components the appliance must be disconnected from the mains switch off the fuse m Do not use extension leads in places with baths or showers Operation Please always remove the drip bowl prior to opening the panel flap see chapter Accessing the programming device on page 27 Firstly close the panel flap and then insert the drip bowl until it comes to rest Failure to do so may result in damage to the flap and the hinge m some parts of the appliance such as the water drainage pipe and the brew ing unit need to be heated up in order for the appliance to operate properly Caution Risk of burning m Please be careful when handling the hot water discharge pipe and the brew ing unit Do not put your hand under these parts Wait until the hot parts have cooled down m he power supply cable may not be replaced by the user Please contact qualified technicians only should the appliance develop a fault m he rinsing procedure should not be interrupted once it has commenced since residual cleaning agent may otherwise get into the inside of the brew ing unit Caution Danger of poisoning m Do not put your hands inside the container when filling up with coffee m Ihe appliance must be switched off and have cooled down prior to being cleaned manually m he appliance may be installed in a tall kitchen unit m Only pour cold
13. ceed to enter the drink for the following button After making the adjustment press the RESET button 3 in order to exit the sub menu and return to the main menu The new setting will have been stored EKV 6800 0M Coffee grounds number Brewing unit setting Once a certain pre set number of coffee grounds portions in the box for coffee grounds has been reached the display will indicate that it is time to empty the box The machine will be locked so that the box can safely be emptied Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Grounds number Press the ENTER button again to go through the drinks previously set Pressing the CURSOR buttons 4 4 and 2 to set the number of coffee grounds portions after which the display is to indicate that it is time to empty the box max 40 portions Press the RESET button 3 to leave the sub menu and return to the main menu In order to reset the settings the appliance must remain switched on when the coffee grounds box is emptied Warning Time to clean the milk frother A certain period of use has been programmed for the milk frother number of hours Once this time has been reached max 12 hours the display will warn that it is time to clean the milk frother If you wish to change this time proceed as follows Press the ENTER button to access th
14. clean drinking water into the tank intended for water Hot water and other liquids may damage the appliance m Change the water every day in order to avoid the formation of bacteria m Do not use steam or pressure cleaners to clean the appliance This could damage your appliance in such a manner that it might put your life at risk m f the coffee machine cannot be switched off due to a defect disconnect the fuse in your home immediately and call customer service 21 Before using the appliance for the first time Mains voltage Check to ensure that the power supply in your home corresponds with that indicated on the nameplate inside the appliance 208 240 V 50Hz 1800W Disposing of the packaging material and your old appliance Please dispose of the packaging material that came with your appliance in an environmentally friendly manner If you bought your appliance in Germany the dealer who sold it to you will take the packaging back for recycling Recycling the packaging material in this manner saves on resources and cuts down on waste Your old appliance still contains useful raw materials Please hand in your old appliance at a recycling collection point Prior to doing so make your old appliances unserviceable in order to prevent it from being misused Initial cleaning Please read this chapter through carefully before using your appliance for the first time If cleaned correctly and looked after regularly the a
15. cleaned correctly and looked after regularly the appliance will retain its appearance and remain clean for many years The following instructions will helo you to clean and care for the various types of surfaces gently but thoroughly Do not use steam or pressure cleaners to clean the appliance The appliance can become so damaged that it may put your life at risk Risk of burning Leave the appliance to cool down sufficiently before cleaning it Please follow the instructions provided with the cleaning agents you plan to use All of the cleaning agents are available from the KUPPERSBUSCH Customer Service Casing Clean the casing inside and outside with a soft damp cloth Clean the swivel pipe of the dispense every time it is used After milk has been heated up heat up some water and allow it to run through in order to clean the pipe from the inside Do not use any aggressive or bleach based cleaning agents that contain active oxygen chlorine or other caustic substances nor should any abrasive cleaning or scouring agents such as steel wool soap impregnated steel wool hard brushes metal or plastic sponges or Sponges with an abrasive surface abrasive side be used Water tank Only appliances which are not connected to the domestic water supply have a water tank The water tank must be rinsed out daily and filled with fresh water amp gt lf there is a visible build up of limescale in the water tank it may b
16. ct product is indicated again Making decaffeinated coffee Partly pull the coffee machine out of the kitchen unit Qpen the decaffeinated coffee container in the upper part of the machine and pour one portion of ground decaffeinated coffee into the decaffein ated coffee container A Attention Only use coffee powder Place one cup under both dispensers The coffee is always poured from both dispensers simultaneously Firstly press the button for decaffeinated coffee once and then press the button for the type of coffee you require The display will either show Decaffeinated Coffee Creme or Decaffeinated Espresso or Decaffeinated Coffee etc depending on what you have selected The coffee is prepared Leave the cup under the dispensers until the drink display goes off and Select product is indicated again Dispensing hot water This enables hot water to be dispensed for making tea and other beverages which are infused gt Prior to carrying out the next step ensure that there is water in the tank Place a suitable vessel under the hot water dispenser for hot water once Press the dispense button The display will indicate select product Tea Hot water will flow out of the dispenser until you press the dispense button Risk of burning The water dispensed is very hot Don t touch the dispenser pipe EKV 6800 0M Cleaning and care If
17. deleted and the standard programming settings can be restored see List of standard parameter Proceed as follows Switch the machine off Switch it on again keeping the buttons 1 ENTER and 3 RESET pressed simultaneously until the display indicates Please Wait Preset Data List of standard parameters Water volume in ml Milk dispenser Drink in seconds lt rmm ep Ristretto 2 Ristretto Espresso gt oO O1 oO NO lt 2 2 Espresso lt rmm ep Caff creme PO Oo lt lt 1 mn N w 2 Coffee creme NMI Oj O 2 coffees Z Z Z O O NO Cappuccino Large cappuccino O1 oO Macchiato Milk coffee Milk Coffee grounds metre ei O1 Po lt m dp Cleaning milk frother Message Cleaning Cleaning brewing unit Coffee temperature i DO O1 Steam temperature Decalcification lt rmm ep NO nm m EKV 6800 0M What to do if trouble occurs A Repairs must be carried out by an authorized service technician You may rectify some of the faults yourself You should firstly check that you are using the appliance correctly Repairs during the guarantee period will be charged if they are caused by a user error or by failure to observe the following instructions Display message fect memey pe ooo Please wait Heating Select product The machine is ready to be All of the products are avai
18. e removed with an antiliming agent see chapter Warning Time to decal cify on page 30 Remove the water tank from the appliance and rinse it thoroughly after it has been descaled The water tank should be rinsed out daily and filled with fresh water Only use fresh cold water for filling up the tank Never fill in any milk mineral water or other fluids Work area Clean the work area as follows Remove the drip bowl Remove the drip grid Release the front panel flap Open it and wipe it carefully Make sure that the steel is not scratched Open the brewing unit flap so that the container for coffee grounds can be removed more easily If necessary remove any residual coffee that may have gathered on the sides of the coffee dispenser Remove the coffee grounds box and rinse it carefully Take care not to scratch the steel Use a brush to remove encrusted residual coffee from the gasket the plungers and the inside of the brewing unit Cleaning and decalcification programs The appliance is equipped with a fully automatic cleaning and decalcification program The machine is set for cleaning the brewing unit with detergent tabs and for washing the milk cycle devices with a liquid detergent Decalcification is to be carried out with powder The cleaning program regulates the dispensing of hot water intermittently with waiting intervals in between The entire cycle takes about 4 minutes The decalci
19. e sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Milk Clean Warn H Press the ENTER button again The CURSOR buttons 2 w and 4 may be used to adjust the number of hours after which the warning sign for cleaning is indicated gt We recommend a maximum setting of 2 hours at the most Press the RESET button 3 to exit the sub menu and return to the main menu The new setting will have been stored Warning Time to clean the brewing unit A certain number of brewing cycles has been programmed after which the display will indicate that it is time to clean the brewing unit Once this time has been reached a warning that it is time to clean will appear If you wish to change this time proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 and 4 to scroll the various sub men us until the display indicates Clean warning Press the ENTER button again The CURSOR buttons 4 and 2 w can be used to set the number of cycles number of coffees dispensed after which the instructions to clean will be shown cae We recommend that at least 10 cycles be set Press the RESET button 3 to exit the sub menu and return to the main menu The new setting will have been stored The time for resetting the brewing unit can be programmed in this program item This time has been set in the fac
20. ely 1 5 minutes in order to prevent the pump from becoming overheated In this case switch the appliance off with the main switch and switch it on again The coffee machine is equipped with an LED system that illuminates the dispenser area as soon as the red light up button located next to the ON OFF switch is pressed EKV 6800 0M Foam consistency and amount of foam The amount of foam for cappuccino is pre set in the factory It is possible to adjust the quantity of foam by adjusting the air entrance screw Thanks to this adjustment mechanism which changes the consistency of the milk froth produced by the milk frother you have a choice of creamy medium or less creamy Cappuccino ce This operation can also be carried out with the machine on Release the front panel door and open it Open the brewing unit door Loosen the safety ring A by turning it anti clockwise Turn the thumb screw B manually as indi cated on the label on the door in order to B reduce or raise the volume of air Turn the screw anti clockwise to reduce the quantity of foam Turn the screw clockwise for more foam Tighten the safety ring again turn it clockwise after the adjustments have been made Then close the doors again Milk temperature The milk temperature for cappuccino can be adjusted by operating the pinch screw see arrow ce This operation can also be carried out with the machine on Pull out the m
21. fication program is a special program that runs separately Please refer to the supplement for information on how frequently decalcification must be carried out c Please also observe the brief instructions enclosed for the individ ual cleaning steps We recommend cleaning at least once a day with suitable detergents as the milk which remains in the brewing unit could be a health risk In addition it would be advisable to clean the milk frother two hours after the last milk beverage has been dispensed see Special functions Cleaning agents You can order the following cleaning agents from the K ppersbusch Customer Service Liquid detergent Spare parts n 527 288 Spare parts n 527 289 Spare parts n 527 287 Antiliming powder 10 bags Detergent tabs 10 pieces Preparation The water tank must be filled right up with water prior to carrying out the washing cycle not for appliances connected to the tap water supply Please also observe the instructions on the label on the inside of the door Do not interrupt the washing cycle once it has been started with deter gent tabs Residues of the tabs may remain in the machine Do not interrupt the decalcification cycle once it has been started Resid ual antiliming powder may remain in the machine The water tank and the entire brewing unit must be rinsed thor oughly once the decalcifying procedure has been completed See chapter Cleaning the milk frother and
22. ilk drawer in the front part of the machine Open the milk box and insert it Now insert the milk suction tube into the opening ce Please use commercially available long life milk with a fat content of at least 3 5 or fresh milk To modify the milk suction flow and to regulate the respective temperature turn the pinch screw see arrow provided for this purpose either clockwise or anti clockwise in order to Increase or decrease the suction flow of milk and the respective tempera ture Making coffee A Please observe the safety instructions on page 21 If the machine is ready for operation Select product on the display you can start making coffee at just the right consistent temperature The water will rise upwards ensuring that the coffee is thoroughly filtered and at the same time preventing the coffee powder and the coffee grounds from spilling The special grinder with 50mm grinding discs which operates professionally at a low speed and a consistent degree of grinding ensures that the coffee will not burn The appliance has two boilers one for coffee and one for hot water The boilers are linked so that water for cappuccino or tea will already be hot Electronic push buttons The push buttons enable various beverages to be conveniently selected at the push of a button The buttons have been assigned in the factory You can however allocate other beverages to the buttons according to your personal tas
23. inks no longer available Machine is blocked The coffee will not be made and the coffee powder will be ejected Wait until the appliance goes into The optimal operating the ready to operate mode 3 5 minutes Empty the drawer for coffee grounds A Prior to putting the drawer back the display must indi cate Machine off Grounds bin out Close the front panel flap and lock it Do a washing cycle see Cleaning and care page 25 Open and close the front panel flap Open and close the panel flap The control unit will repeat the starting up procedure of the machine Fill up the water tank The defect part may only be replaced by a Kuppersbusch Customer Service technician Reduce the quantity of coffee powder temperature is only reached after 3 5 minutes Have the appliance checked by customer service if the alarm sounds again Have the appliance checked by customer service if the alarm sounds again The machine can be operated manually until it has been repaired Press the coffeebutton again once the required quantity has been dispensed They also serve aS STOP BUTTONS After filling briefly press the but ton for dispensing hot water in order to get rid of any air bubbles not for appliances connected to the tap water supply This alarm blocks the machine 31 Installation instructions for professional fitters Instructions for fitting Installation m The
24. kitchen unit m Ihe built in unit must be firmly attached to the floor or on the back panels since failure to do so could result in the unit falling over due to its considerable _ own weight m he fully automatic coffee machine must be installed at a safe distance from other sources of heat such as home appliances in order to avoid an ex cessive rise In temperature Insert the screws in the holes of the corner elements without tightening Installation dimensions EKV 6800 0 en 6 metal plates each 1 mm thick are supplied with the appliance for positioning between the guides and the sides of the kitchen unit in order to fill the excess space should the unit be more than 562 mm wide Number of distance plates 2 2 f necessary insert the plates as described above Check that the distance between the fixing angles distance B is 558 mm Fix the guides to the seat of the coffee machine tightening all the Screws 32 EKV 6800 0M Ensure that the power supply cable can be lead freely through the back wall Tech nical data In order to avoid overheating the coffee machine make an opening of at least 300 mm x 100 mm at the back of the seat to allow the air to circu ne Fully automatic coffee machine Class 1 l Nominal voltage 120 V Installation E Power 1800 W Insert the coffee machine Into the kitchen unit support from below insert ad 1
25. lable operated Select product Grounds Bin Full Machine off Front panel open Please clean XXXXXX Group error Timeout Filling Up Boiler Refill WaterTank If this fault occurs the dis play will indicate an error alternately with the current drink selected Refill WaterTank Error Coffee temperature Error Steam temperature Too much coffee powder The appliance is still heating up The front panel flap is not closed The time set for cleaning cycle has been exceeded The time limit for the movement of the brewing unit motor plunger 10 sec was exceeded The pre set time of 3 minutes for filling up the boiler was exceeded The water metre does not transmit any impulses to the control unit The water tank is empty Temperature probe not working Either an excessively long grinding time was programmed or too much coffee powder was filled into the box for decaffeinated coffee Keys locked No drinks available Keys locked No drinks available Keys locked No drinks available Machine off The machine will still function nor mally Drinks no longer available Machine blocked Drinks no longer available Machine locked Drinks will only stop being dis pensed after 60 seconds Press the coffee button again in order to stop the dispensing proce dure before this time The procedure of making coffee is interrupted Drinks are no longer available Machine blocked Dr
26. manufacturer cannot be held responsible for damage to property Remove the coffee machine from the packaging and make sure that it is or injury to persons caused by failure to comply with the safety in not damaged Do not install a damaged machine Contact the retailer structions and installation and maintenance instructions contained in this handbook Position the metal plate in the upper part of the seat of the coffee ma chine and push it through to the back wall of the kitchen unit m statutory regulations and the connection specifications issued by the local power supply company must be strictly observed m Before connecting the appliance to the power supply make sure that the supply voltage complies with the voltage of the appliance Fix tt with 4 screws m When carrying out repairs the appliance must be disconnected from the mains Disconnect the fuse m t must be ensured that no accidental contact can be made once the appli ance has been installed m Ihe machine may only be connected to properly installed connection sock ets Installing a connection socket or replacing the connection leads may u Be Insert the two fixing angles only be carried out by a qualified electrician on observance of respective equipped with guides onto the sur Eu face of the seat a ee nn nn his a a with a contact opening of fixing them 90 mm from the front at least 3 mm be used on the installation side edge of the
27. menus until the display indicates Water Filter L Press the ENTER button again The CURSOR buttons 4 and 2 w can be used to set the number of litres quantity of water dispensed after which the display will indicate that it is time to decalcify Press the RESET button 3 to exit the sub menu and return to the main menu The new setting will have been stored Exiting the programming system It is sufficient to close the front panel flaps again in order to exit the programming system The display will indicate Please wait Heating The appliance will now go into the stand by mode Please wait until the display indicates Select product The appliance is now ready to make the drink required with the newly stored settings 30 Special functions Resetting the water quantity metre With this function the number of litres of water used can be reset at zero Proceed as follows Switch the machine off Switch it on again keeping the button pressed until the display indicates Reset H20 Filter Counter Wait Resetting the washing cycles With this function the number of cleaning cycles carried out can be reset at zero Proceed as follows Switch the machine off Switch it on again keeping the i indicates Reset Clean Counter Wait button pressed until the display Resetting to standard parameters With this function incorrect operating data can be
28. mmed Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Coffee temperature Press the ENTER button again to go through the drinks previously set Press the CURSOR buttons 4 a and 2 to increase decrease the temperature of the coffee boiler ce The pre set temperature is 98 C Press the RESET button 3 to exit the sub menu and return to the main menu The new setting will have been stored steam temperature The temperature of the steam is programmed The settings have been made in the factory and should not be adjusted Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 to scroll the various sub men us until the display indicates Steam temperature Press the ENTER button again to go through the drinks previously set Press the CURSOR buttons 4 and 2 to increase or decrease the temperature of the steam Press the RESET button 3 to exit the sub menu and return to the main menu The new setting will have been stored Warning Time to decalcify A certain number of litres of water is programmed after which the display will indicate that it is time to decalcify If you wish to change this quantity proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 and 4 4 to go through the various sub
29. n piece a gt For hygienic reasons it is essential to clean the milk frother if more than two hours lapse after the last milk drink was made In order to do so plunge the milk suction tube into hot water instead of into milk ce Please observe the label on the interior of the door flap EKV 6800 0M Programming The appliance has been set in the factory so that you can make coffee without having to do any additional programming Various settings can be programmed individually in order to adjust the coffee to suit your personal taste A Attention The manufacturer assumes no liability for faulty or incorrect programming The following settings can be programmed 1 Cumulative Total 9 Cleaning the milk frother 2 Button assignment 10 Cleaning the brewing unit 3 Quantity of water 11 Group setting 4 Grinding time 12 Grinder calibration 5 Milk time 13 Grinder setting 6 Pre brewing 14 Coffee temperature 7 Tamping 15 Steam temperature 8 Coffee grounds metre 16 Decalcification Accessing the programming device A The appliance must be switched on A Please always remove the drip bowl prior to opening the front panel flap Proceed as follows to access the programming mode Partly pull out the appliance Open the flap on the front with the help of the re lease button on the right side of the appliance The display will indicate Machine Off Front Panel Open Press the ENTER button P
30. nnecting the appliance to the mains and repairing and servicing it may only be carried out by a qualified electrician in accordance with currently valid safety regulations Any work not carried out properly is a safety risk m he appliance may only be installed and connected to the power and water supply in accordance with the separate instructions for assembly and instal lation Please have the necessary work carried out by a professional fitter electrician m he appliance is intended to be used for making coffee in the home In the case of operation other than for the intended purpose or in case of incorrect handling no liability will be assumed for any resulting damage m Do not switch the appliance on until it has been installed m For the purpose of electrical safety this appliance must be earthed Please contact a qualified electrician m Ihe manufacturer will not be held liable for any damage caused by failure to ground the appliance properly m Never use an appliance which has a defect or one with a defective supply line m Ihe manufacturer will not be held liable or make any compensation what soever for consequences or damage resulting from improper installation or in the case of failure to carry out maintenance work or if such maintenance work was insufficient Safety m Do not subject the appliance to weather related influences rain snow or frost and do not operate it with wet hands m Do not remove the electri
31. ppliance will retain its appearance and remain clean for many years The following tips will help you to clean and care for the various surfaces gently but thoroughly N Switch off the appliance prior to commencing with cleaning Do not use steam or pressure cleaners to clean the appliance This could damage your appliance in such a manner that it might put your life at risk Risk of burning Leave the appliance to cool down sufficiently before cleaning it m Pull the appliance out far enough to enable the cover on the top of the appliance to be opened take the water tank out at the top and clean it with water and washing up liquid Rinse it carefully to remove any residual washing up liquid not for appliances connected to the tap water supply Do not under any circumstances use any aggressive or bleach based cleaning agents that contain active oxygen chlorine or other caustic substances abrasive cleaning or scouring agents such as steel wool soap impregnated Steel wool hard brushes metal or plastic sponges or sponges with an abrasive surface abrasive side 22 Initial operation Filling the appliance Attention The appliance must be partly or fully pulled out in order to be filled Please do this slowly and very carefully Remove the water tank fill in water replace the tank and close the cover not for appliances connected to the tap water supply Lift up the lid of the coffee bean con tainer and
32. s until the drink display goes off and Select product is displayed again Two cups of espresso or caff creme Place two cups under the dispensers as shown in the illustration The coffee is always poured from both dispensers simultaneously Press the button for espresso once or press the button for coffee creme once The display will show the kind of coffee selected The coffee is prepared Leave the cups under the dispensers until the drink display goes off and Select product is indicated again Making coffee gt Use a larger cup than for coffee creme Place one cup under both dispensers The coffee is always poured from both dispensers simultaneously ONCE The display will indicate Coffee Press the button for coffee The coffee is prepared Leave the cup under the dispensers until the drink display goes off and Select product is indicated again 24 Making cappuccino Cappuccino is espresso topped with foamed milk ce Use a larger cup than for coffee creme Pull out the milk drawer in the front part of the appliance Open the milk box and insert it Now insert the milk suction tube into the opening Place a cappuccino cup under the dispensers Press the button for cappuccino P The display will indicate Cappuccino The cappuccino is prepared Leave the cup under the dispensers until the drink display goes off and Sele
33. splay will indicate Clean gt During the entire washing and rinsing phase it is advisable to put a vessel under the coffee dispenser unit or to empty the drip bowl at the end of the washing and rinsing cycle Automatic decalcification Pull the appliance out far enough to be able to open up the lid of the water tank Pour 1 litre of water with a whole bag of antiliming agent into the water tank Wait until the agent has dissolved in the water and close the cover again Pull out the left drawer Pour approx 1 litre of water into a suitable vessel and place it in the milk box com partment as shown on the illustration nsert the milk suction tube Place a suitable collection vessel with a i capacity of approx 1 5 2 litres under the coffee dispenser so that the detergent liquid dispensed can be collected If you now press the button ES decaffeinated coffee until the display shows Clean Insert Cleaner the decalcifying program will run just like the cleaning program previously described c Please read the chapter on Automatic cleaning and follow all of the instructions At the end of the cleaning program the display will indicate Select product 26 Decalcifying appliances connected to the tap water supply Automatically decalcifying the brewing unit with the integrated decalcifying program using tabs can only be carried out on appliances not connected to the tap w
34. te see chapter Button assignment Product name on page 27 Standard configuration One cup of espresso Two cups of espresso One cup of caffe creme Two cups of caffe creme One cup of decaffeinated coffee One cup of coffee Hot water dispenser CO N DO Oo A N 1_ One cup of cappuccino Height adjustable coffee dispenser The height of the dispenser unit can be manually adjusted so that any type of cup will fit under it This will prevent coffee from splashing Bring the dispenser into the required position carefully in order to limit the Space between the dispenser and the cup 23 Switching on the appliance Press the ON OFF switch toggle switch which is located on top of the dispenser to turn on the appliance The display will indicate Please wait Heating At the end of the self diagnosis cycle a max of 3 minutes when the machine is cold and when the machine has heated up the display will indicate Select product Making espresso and coffee creme Both coffees are made in the same way One cup of espresso or coffee creme Place one cup under the two dispensers as indicated in the illustration The beverage is always poured from both dispensers simultaneously Press the button for espresso SS once or press the button for coffee creme once The display will show the kind of coffee selected The coffee is prepared Leave the cup under the dispenser
35. tored Pre brewing For each individual drink the pre brewing time of the quantity of coffee can be activated or deactivated Proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 to scroll the various sub men us until the display indicates Pre Brewing Press the ENTER button again in order to go through the drinks previously set With the CURSOR buttons 4 and 2 you can activate or deactivate the pre brewing procedure for the individual drinks YES or NO Once you have selected a setting press the ENTER button again to confirm the setting and to proceed with the setting for the drink of the next button After making the adjustment press the RESET button 3 in order to exit the sub menu and return to the main menu The new setting will have been stored Tamping Compression of the coffee can be activated or deactivated for each individual drink Proceed as follows Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Tamping Press the ENTER button again in order to go through the previously set drinks With the CURSOR buttons 4 and 2 w you can activate or deactivate the tamping procedure for the individual drinks YES or NO Once you have selected a setting press the ENTER button again to confirm the setting and pro
36. tory and should not be adjusted We recommend that adjustments to this programming system only be carried out by authorized specialists or by the K PPERSBUSCH Customer Service Grinder calibration This programming item can be used to extend the grinding time by 0 1 seconds every 50 250 times a coffee is dispensed Setting the parameter at 0 disables the function Pressing the CURSOR buttons 4 and 2 w will increase reduce the number of coffees dispensed after which the grinding time is to be increased The settings that can be selected are 0 50 100 150 200 and 250 All of the settings have been made in the factory and should not be changed We recommend that adjustments to this programming system only be carried out by authorized specialists or by the K PPERSBUSCH Customer Service Grinder setting A Please always remove the drip bowl prior to opening the front panel flap Firstly close the flap and then insert the drip bowl until it comes to rest Failure to do so may result in damage to the door and the hinge Firstly release the panel flap and then open up the brewing unit flap The degree of fineness of the ground coffee can be adjusted with the key supplied Turn clockwise to grind more finely for thicker coffee Turn anti clockwise for more coarsely ground coffee for a more fluid coffee Then close the flaps again 29 Coffee temperature The temperature of the coffee boiler is progra
37. ull the white micro switch located inside the flap outwards The display will indicate Please wait Heating Once the dispensing cycle has finished the appli ance will rest and the display will show Cumulative Total If you are in the programming mode a second function will have been allocated to four of the buttons Pressing the buttons will enable you to scroll through all of the menu items 1 ENTER Access menu sub menu and confirm data 2 4 CURSOR wand 4 to go through the menu and increase decrease settings 3 RESET back to the previous menu Item Cumulative Total In accordance with the button assignment pre set in the factory or your individual button assignment the total number of measures used for every single drink is indicated Press the ENTER button to access the sub menu Press the CURSOR buttons 2 w and 4 4 to scroll the various sub men us until the display indicates Cumulative Total Press the ENTER button again Pressing the CURSOR buttons 4 and 2 shows the settings for each individual drink in the sequence of the button assignment Example for 16 espressos dispensed Cumulative Total Espresso 00016 To set the number of drinks counted onto zero select the respective drink with the CURSOR buttons and keep buttons 2 and 4 A w simul taneously pressed until the display shows Counters Reset After the setting has been adjusted press
38. y and the electronic touch controls both programming the appliance and operating it are easy and convenient m Clear text display m Electronic push buttons m A genuine two cup fully automatic coffee machine with precisely dispensed coffee thanks to a micro processor m Removable thermo controlled brewing unit m Consistency of milk cream adjustable m imed hot water dispenser m Grinder with 50 mm grinders m Container for one pound of coffee m wo separate boilers one for coffee and one for hot water m Integrated milk frother with adjustable foam consistency for cappuccino m Height adjustable coffee dispenser m Drawer for coffee grounds with a safety block programmable for up to 40 portions m 5 litre water tank not for appliances connected to the tap water supply m Quick and easy maintenance by means of press button rinsing of the brewing unit and the milk frother m Electronically programmed coffee tamper m Coffee ground when it is made freshly brewed coffee at all times m Self diagnosis system m Operating status indicated on the display m Automatic rinsing programs Safety instructions General m Packaging materials such as foil or polystyrene may put children at risk Danger of suffocation Keep packaging material well away from children Connection and operation m Before connecting the appliance to the mains make sure that the voltage of the building corresponds to that of the appliance m Co
Download Pdf Manuals
Related Search