Korg Radias MMT User's Manual
Contents
1. 0 0 TO MODULE TO MODULE 2nd Keyboard Assembly 73 88 Joystick X axis This will operate in the same way as the PitchBend wheel of the RADIAS KB Moving the joystick in the X direction left right will apply a pitch bend effect according to the BendRange setting of the Program Edit mode P05 PITCH page and pitch bend change messages will be transmitted on the MIDI channel of the timbre selected by TIMBRE SELECT When pitch bend change messages are received the result will be the same as when you operate the joystick note If you want to apply a pitch bend effect set the Program Edit mode P03 4 TIMBRE MIDI tab page PBnd parameter to O Enable Make this setting for each timbre E3 If you want pitch bend change messages to be received and transmitted set the Global mode P06 MIDI FILTER page PitchBend parameter to O Enable no If you want to use the joystick X axis left right as a modulation source for another parameter set the following parameters to P Bend according to the parameter that you want to control e Virtual patch P11 PATCH Source RADIAS owner s manual p 91 e Vocoder P07 FILTER FeModSrc RADIAS owner s manual p 105 Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 In these cases the parameter will be controlled with mm 64 and bb 00 as 0 the center value ina range of 1272. to 127 received on the MIDI channel of the timbre Y axis This will operate in the same way as the Modulation wheel of the RADIAS KB Moving the joystick in the Y direction will apply a vibrato effect from LFO2 according to the VibratInt setting of the Program Edit mode P05 PITCH page and modulation depth CC 01 will be transmitted on the MIDI channel of the timbre selected by TIMBRE SELECT When CC 01 is received the result will be the same as when you operate the joystick note If you want to apply a vibrato effect by moving the joystick in the Y direction set the Program Edit mode P03 5 TIMBRE CC A tab page Cntrl parameter to O Enable Make this setting for each timbre E3 Ifyou want MIDI control change messages to be transmitted and received set the Global mode P06 MIDI FILTER page parameter Ctrl Chg to O Enable note If you want to use the joystick Y axis as a modulation source for another parameter set the following parameters to M Wheel according to the parameter that you want to control e Virtual patch P11 PATCH Source RADIAS owner s manual p 91 e Vocoder P07 FILTER FeModSrc RADIAS owner s manual p 105 e Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 Y axis By setting one of the Global mode P04 MIDI page parameters MIDI1 MIDI5 to 002 you can use the Y axis of the joystick as the following sou
3. RADETAS SYNTHESIZER VOCODER Function added in system version 2 0 RADIAS synthesizer vocoder RADIAS operating system version 2 0 adds the following functions Please read this document in conjunction with the RADIAS owner s manual included with your RADIAS or RADIAS R Virtual Patch RADIAS version 2 0 adds the following parameters as virtual patch modulation destinations This allows you even greater sound making diversity p 92 P11 PATCH page Dest Destination Portamnto Modulation will be applied to the Portamnto portamento time parameter of the PO5 1 PITCH page OSC1Ctrl2 Modulation will be applied to the Control2 parameter of the P06 1 OSC MIXER OSC1 tab page Filt EG1 Filt1 KTrk Modulation will be applied to the EG1 Int or KeyTrack parameter of the PO7 1 FILTER FILTER1 tab page Filt2Reso Filt2EG1 Filt2KTrk Modulation will be applied to the Resonance EG1 Int or KeyTrack parameter of the P07 2 FILTER FILTER2 tab page EG1Attack EG1Decay EG1Sustain EG1Releas Modulation will be applied to the Attack Decay Sustain or Release parameter of the P09 1 EG EG1 tab page EG2Attack EG2Decay EG2Sustain EG2Releas Modulation will be applied to the Attack Decay Sustain or Release parameter of the P09 2 EG EG2 tab page EG3Attack EG3Decay EG3Sustain EG3Releas Modula
4. RADIAS R or M3 M to the TO MODULE 2nd connector not only will the ribbon controller be unavailable but the RADIAS R or M3 M connected to the TO MODULE 2nd connector may malfunction when you operate the ribbon controller If you make connections in this way please disable ribbon controller reception on the RADIAS R or M3 M that is connected to the TO MODULE 2nd connector Global parameters So that you can connect the RADIAS to the 61 key 73 key 88 key keyboard assembly used by the M3 music workstation sampler and play the RADIAS from that keyboard RADIAS version 2 0 adds the following functions as choices that can be selected in MIDI1 MIDIS p 117 PO4 1 MIDI page MIDI1 MIDI5 016 CC 16 Select this if you want to use the ribbon controller of the keyboard assembly as a modulation source for the virtual patch note The ribbon controller will produce a control change value of 64 when you release your hand kh When using the ribbon controller of the 73 key or 88 key keyboard assembly you may not obtain the expected result unless you select 016 017 CC 17 019 CC 19 020 CC 20 021 CC 21 Select these if you want to use the MIDI control changes transmitted by the four user sliders Modulation Sliders 5 6 7 and 8 of the M3 control surface as modulation sources for virtual patches note For 017 019 020 and 021 the resulting modulation will be zero whe
5. e P04 MIDI page parameters MIDIM MIDI5 are set to 016 you ll be able to use the ribbon controller as a source for the following Modulation source for a virtual patch RADIAS owner s manual p 91 Modulation source for the vocoder filter RADIAS owner s manual p 105 Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 note With the factory settings MIDI1 is set to 016 ke If MIDI1 is set to 016 the effect may not return to 0 when you take your hand off the ribbon controller If you want the effect to return to 0 when you take your hand off the ribbon controller set MIDI1 to 016 When you operate the ribbon controller control change CC 16 messages will be transmitted on the MIDI channel of the timbre that is selected in TIMBRE SELECT When CC 16 is received the result will be the same as when you operate the ribbon controller note If you want to use the ribbon controller to apply an effect set the Program Edit mode P03 5 TIMBRE CC A tab page Cntrl parameter to O Enable Make this setting for each timbre fp If you want control change messages to be transmitted and received set the Global mode P06 MIDI FILTER page parameter Ctrl Chg to O Enable A If you connect the RADIAS R to the TO MODULE connector the ribbon controller will be unavailable If you connect the RADIAS R to the TO MODULE connector and the
6. n the slider etc is set to the center position control change value of 064 For 017 019 020 and 021 the resulting modulation will be zero when the slider etc is set to the 0 position control change value of 0 Select the choice that will give you the desired type of change when you operate the slider or other controller Monitoring the audio output of the M3 M and RADIAS R If you would like an easy way to monitor the audio output of the M3 M and RADIAS R without using a mixer or similar device connect the RADIAS R s MAIN OUT jacks to the M3 M s AUDIO INPUT jacks set the M3 M s rear panel AUDIO INPUT MIC LINE switch to LINE and set the Global PO Basic Setup Audio page Bus Select setting to L R With these settings you ll be able to monitor the sound via the M3 M s headphone jack or main output jacks To adjust the volume use the M3 M s rear panel AUDIO INPUT LEVEL knob and the RADIAS R s VOLUME knob Function added in system version 2 0 MIDI settings when using an M3 M and RADIAS R together MIDI OUT J MIDI IN TO MODULE 2nd NOU Keyboard Assembly 73 88 Preventing the RADIAS R from double triggering If you have made the connections shown above for example to synchronize the tempo of the M3 M and the RADIAS R messages such as note on from the TO MODULE 2nd co
7. nnector and the MIDI messages from the M3 M s MIDI OUT connector may cause the RADIAS R to sound duplicate notes To prevent this make the following settings RADIAS R GLOBAL P04 1 MIDI page Clock Exter nal MIDI or Auto RADIAS owner s manual p 117 e RADIAS R GLOBAL P04 1 MIDI page LocalCtrl Off RADIAS owner s manual p 116 If you turn the RADIAS R s local control LocalCtrl off note on messages etc from the TO MODULE 2nd connector will not be received Preventing KARMA generated note data from being received by the RADIAS R If you have made the connections shown above and are playing an M3 M program or combi that uses KARMA such as a rhythmic drum program generated by KARMA the note data from the KARMA module may be transmitted to the RADIAS R To prevent this make the following settings M3 M Global P1 MIDI MIDI Routing page Enable KARMA Module to MIDI OUT Off e RADIAS R GLOBAL P04 1 MIDI page LocalCtrl On RADIAS owner s manual p 116 With these settings the M3 M will not transmit note data from the keyboard either so turn the RADIAS R s LocalCtrl setting On KORG INC 4015 2 Yanokuchi Inagi city Tokyo 206 0812 Japan 2007 KORG INC
8. nnel of the timbre selected by TIMBRE SELECT Switch on will transmit a value of 127 and switch off will transmit a value of 0 When CC 80 SW1 or CC 81 SW2 are received the on off status of the switch will change A value of 64 or higher will turn the switch on and a value of 63 or lower will turn it off note If you want to apply an effect using SW1 SW2 set the Program Edit mode PO3 5 TIMBRE CC A tab page Cntrl parameter to O Enable Make this setting for each timbre note If you want control change messages to be transmitted and received set the Global mode P06 MIDI FILTER page parameter Ctrl Chg to O Enable Keyboard aftertouch Aftertouch from the keyboard is available only if the M3 M is connected to the TO MODULE connector of the 73 88 key keyboard assembly or if the RADIAS R is connected to the TO MODULE 2nd connector If one of the Global mode P04 MIDI page parameters MIDI1 MIDI5 are set to A Touch you ll be able to use keyboard aftertouch as a source for the following Modulation source for a virtual patch RADIAS owner s manual p 91 Modulation source for the vocoder filter RADIAS owner s manual p 105 Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 LE With the factory settings MIDI5 is set to A Touch When you apply keyboard aftertouch channel aftertouch messages will be transmitted on the MIDI cha
9. nnel of the timbre that is selected in TIMBRE SELECT When channel aftertouch is received the result will be the same as when you operate the keyboard note If you want to use aftertouch to apply an effect set the Program Edit mode PO3 4 TIMBRE MIDI tab page AT parameter to O Enable Make this setting for each timbre note If you want aftertouch messages to be transmitted and received set the Global mode P06 MIDI FILTER page parameter Ctrl Chg to O Enable amp If you connect the RADIAS R to the TO MODULE connector the keyboard s aftertouch will be unavailable If you connect the RADIAS R to the TO MODULE connector and the RADIAS R or M3 M to the TO MODULE 2nd connector not only will the keyboard s aftertouch be unavailable but the RADIAS R or M3 M connected to the TO MODULE 2nd connector may malfunction when you use aftertouch If you make connections in this way please disable aftertouch reception on the RADIAS R or M3 M that is connected to the TO MODULE 2nd connector In the Program Edit mode P03 4 TIMBRE MIDI tab page set AT to x The aftertouch sensitivity of the 73 88 key keyboard assembly cannot be adjusted on the RADIAS R Ribbon controller The ribbon controller is available only if the M3 M is connected to the TO MODULE connector of the 73 88 key keyboard assembly or if the RADIAS R is connected to the TO MODULE 2nd connector If one of the Global mod
10. o 081 On the RADIAS R SW1 SW2 operate only in toggle mode The on off status will alternate each time you press the switch When you change programs the switch will be reset to the off state The lit unlit status of the switch will depend on the connector to which you ve connected the unit If the RADIAS R is connected to the TO MODULE connector If you connect the RADIAS R to the TO MODULE connector of the 61 key or 73 88 key keyboard assembly the status of the switch will match the operation of the RADIAS R The switch will be lit when on and dark when off If the RADIAS R is connected to the TO MODULE 2nd con nector On the 73 88 key keyboard assembly the status of the switch will reflect the setting of the module connected to the TO MODULE connector but will not reflect the status of the module connected to the TO MODULE 2nd connector When you operate the module connected to the TO MODULE 2nd connector you ll need to be aware of the lit dark state of the switch If the program etc of the M3 M connected to the TO MODULE connector was written into memory with an SW1 SW2 setting of Toggle or Off the switch status will match the operation of the RADIAS R connected to the TO MODULE 2nd connector A The on off status of the switch cannot be saved in the RADIAS R program RADIAS synthesizer vocoder When you operate a switch a control change CC 80 SW1 or CC 81 SW2 will be transmitted on the MIDI cha
11. rces Modulation source for a virtual patch RADIAS owner s manual p 91 e Modulation source for the vocoder filter RADIAS owner s manual p 105 e Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 role With the factory settings MIDI2 is set to 002 Function added in system version 2 0 When you operate the joystick in the Y direction control change CC 02 will be transmitted on the MIDI channel of the timbre you ve selected When CC 02 is received the result will be the same as when you operate the joystick If you want to use the joystick Y axis to apply an effect set the Program Edit mode P03 5 TIMBRE CC A tab page Cntrl parameter to O Enable Make this setting for each timbre Eg Ifyou want MIDI control change messages to be transmitted and received set the Global mode P06 MIDI FILTER page parameter Ctrl Chg to O Enable SW1 SW2 By setting one of the Global mode P04 MIDI page parameters MIDI1 MIDI5 to 080 SW1 or 081 SW2 you can use SW1 or SW2 as a source for the following Modulation source for a virtual patch RADIAS owner s manual p 91 Modulation source for the vocoder filter RADIAS owner s manual p 105 Effect control source St Filter Ctrl Src etc RADIAS owner s manual p 125 fey With the factory settings MIDI3 is set to 080 and MIDI4 is set t
12. tion will be applied to the Attack Decay Sustain or Release parameter of the P09 3 EG EG3 tab page Patchllnt Patch2Int Patch 3lnt PatchAlnt PatchSlnt Patch lnt Modulation will be applied to the Intensity parameter of the P11 PATCH P1 PATCH P6 tab pages Connecting the RADIAS R to an M3 keyboard assembly RADIAS version 2 0 allows you to connect the RADIAS tone module RADIAS R to the 61 73 88 key keyboard assembly used by the M3 music workstation sampler and play the RADIAS R from that keyboard A When using the 61 key keyboard assembly keyboard aftertouch and the ribbon controller will not be available A If you re connecting the RADIAS R to the 73 88 key keyboard assembly connect the M3 M to the TO MODULE connector and the RADIAS R to the TO MODULE 2nd connector see illustration below If you connect the RADIAS R to the TO MODULE connector the keyboard s aftertouch and ribbon controller will not be available and the M3 M connected to the TO MODULE 2nd connector may malfunction because of aftertouch If you re connecting the RADIAS R by itself to the 73 88 key keyboard assembly connect it to the TO MODULE connector don t use the TO MODULE 2nd connector In this case too the keyboard s aftertouch and ribbon controller cannot be used GEO Of ia OCOIBJECI M3 M A RADIAS R ry i H i
Download Pdf Manuals
Related Search