Kodak i6000 User's Manual
Contents
1. REPLACING THE INK CARTRIDGE If you are using the Inkjet Printer periodically you will need to change the ink cartridge 1 Turn off the scanner 2 Remove the scanner top cover 3 Lift up the tab at the rear of the ink cartridge and pull it out of the ink cartridge holder 4 Dispose of the empty ink cartridge in accordance with all federal state and local laws 5 Take the new cartridge out of its packaging and remove the protective tape from the cartridge IMPORTANT Do not touch the exposed metal chip or the cartridge could be damaged 6 Insert the ink cartridge into the ink cartridge holder and push the ink cartridge down until it snaps into place 7 Reinstall the scanner top cover and turn on the scanner TROUBLESHOOTING For a list of error codes and possible solutions see the User s Guide Chapter 5 Troubleshooting Periodic and scheduled cleanings should be performed before determining if any further problem resolution is needed Helpful Hints O Always jog the documents to align the leading and bottom edges Visually check the leading edges for bent or curled corners and straighten them as needed O Place the stack of documents halfway into the input tray then slide the stack forward until the left indicator comes on O Be sure the exit wire stop is extended enough to allow approximately 1 2 inch or more than the longest document If you are experiencing image quality problems thoroughl2. e thumbscrew that holds the scan tower door in place a 8 Open the scan tower door 9 Using the cleaning swab wipe both surfaces of the scan heads 10 Close the scan tower door and reinstall the thumbscrew 11 Replace the back cover first then the side cover and turn the scanner on 12 Launch the Kodak ScanTest Software 13 Clean each drive roller by selecting Eject on the Kodak ScanTest Software window Selecting Eject turns the drive rollers for about 5 seconds 14 Each of the drive rollers should be thoroughly cleaned with the swab While the rollers are turning use an up and down motion to clean the entire roller You may need to use several cleaning swabs if the rollers are very dirty 15 Replace the top cover
3. ent procedures see the User s Guide Chapter 4 Maintenance DAILY CLEANING PROCEDURES 1 Launch the Kodak ScanTest Software 2 Open the cleaning card package and remove the cleaning card 3 Place the cleaning card between the entry separation drive roller as shown 4 While holding the cleaning card in place select Scan from the Kodak ScantTest Software window allowing the entry rollers to scrub the card 5 Wait until the motor stops then remove the card and flip the card to a clean corner and repeat Step 4 6 Place the cleaning card in the input tray and select Scan You may need to give the cleaning card a slight push to start it through the transport 7 Turn the cleaning card over and repeat Step 6 8 Scan the cleaning card three or four more times Be sure that you continue to turn the cleaning card to a clean side each time you scan the cleaning card through the transport 9 When finished discard the cleaning card and shut down the Kodak ScanTest Software WEEKLY CLEANING PROCEDURES A thorough cleaning should be performed approximately every fourth cleaning cycle 1 Before starting this procedure perform the daily clean ing procedure Turn off the scanner Remove the scanner top cover Lift and remove the side cover a eN Pull the exit stop wire out about 4 inches to provide adequate clearance for removing the back cover o Lift and remove the back cover 7 Loosen and remove th
4. y clean your scanner SUPPLIES CAT No Description 802 7393 Cleaning Kit Kodak i6000 Series Check Scanners includes cleaning cards and swabs Inkjet Cartridge hp 6602a 830 1087 Items are subject to change INNOVATION OU CAN COUNT OH EASTMAN KODAK COMPANY Document Imaging Rochester New York 14650 Kodak is a trademark of Eastman Kodak Company Eastman Kodak Company 2006 A 61547 6 06 CAT No 123 5779 Part No 9E4522 Kodak 16000 Series Check Scanners Quick Tips www kodak com Kodak Service 1 800 822 1414 Kodak Parts Services 1 800 471 0803 1 585 724 6042 Kodak Professional Services 1 800 525 6325 INDICATOR LIGHTS QO Right LED on red scanner is powered on O Right LED on green scanner is ready for operation and has detected the Kodak t6000 Client Software Q Left LED on amber scanner detects the presence of documents in the input tray POWER SWITCH AND CONNECTORS USB port Power switch Power port USB port connects the scanner to the PC Power switch turns the scanner on and off Power port connects the power cord to the scanner NOTES O Be sure that the USB cable and power cord are secure and connected properly Place the power supply on the floor Do not place it next to the scanner Failure to do so may result in degraded MICR read rates CLEANING AND MAINTENANCE For detailed cleaning and replacem
Download Pdf Manuals
Related Search