Kobe Range Hoods IN-026 SERIES User's Manual
Contents
1. Keep all fan baffle spacer filter oil tunnel oil container and grease laden surfaces clean Grease should not be allowed to accumulate on fan baffle spacer filter oil tunnel oil container Always turn hood ON when cooking Use high settings on cooking range ONLY when necessary Do not leave cooking range unattended when cooking Always use cookware and utensils appropriate for the type and amount of food prepared Use this unit only in the manner intended by the manufacturer Before servicing switch power off at service panel and lock service panel if possible to prevent power from switching on accidentally Clean ventilating fan frequently What to Do In The Event Of a Range Grease Fire SMOTHER FLAMES with a tight fitting lid cookie sheet or metal tray and then turn off the burner KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES If the flames do not go out immediately EVACUATE THE AREAAND CALL THE FIRE DEPARTMENT or 911 NEVER PICK UP A BURNING PAN You May Get Burned DO NOT USE WATER including wet dishcloths or towels a violent steam blast will result Use an extinguisher ONLY if a You Class A extinguisher and know how to operate it b The fire is small and contained in the area where it started c The fire department has been called d You can fight the fire with your back to an exit What to Do If You Smell Gas Extinguish any open flame Do not tr2. 2 E Oil Tunnel 1 F Handle amp Screws Package 1 H Wireless Control 1 FOR MORE INFORMATION PLEASE VISIT OUR WEBSITE WWW KOBERangeHoods com OR CONTACT KOBE RANGE HOODS AT 626 350 1355 3 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation To calculate installation please refer to TABLE 1 All calculation in inches FOR UNDER THE CABINET TABLE 1 Height of Floor to Ceiling Height of Floor to Counter Top Standard 36 Wood Frame Height of Counter Top to Wood Frame Bottom Recommended 27 to 30 Height of Wood Frame SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVES IF REMOVING ANY PARTS FOR INSTALLING CLEANING OR SERVICING NOTE BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER DAMAGE TO THE HOOD MAY OCCUR Insert installation Preparation Before Installation Figure 1 NOTE TO AVOID DAMAGE TO YOUR HOOD PREVENT DEBRIS FROM ENTERING THE VENT OPENING e Decide the location of the venting pipe from the hood to the outside Refer to Figure 1 e A straight short vent run will allow the hood to perform more efficiently e Try to avoid as many transitions elbows and long run as possible This may reduce the performance of the hood e Temporarily wire the hood to test for proper operation before installing e Important Peel protective film off
3. Push Button with LED Array 6 Button Wireless Remote Variable Delay Shutoff 120V 40W Max x 2 Light Bulbs not Included 32 9 16 x 18 1 2 x 10 9 16 2 Piece Adjustable Liner Model No INL36252A 36 x 23 to 25 x 3 Model No INL42252A 42 x 23 to 25 x 3 Model No INL48252A 48 x 23 to 25 x 3 Net Gross IN2636SQB 51 63 QuietMode Low Medium High 385 460 560 700 1 2 3 0 4 0 5 0 42 56 60 64 House Test Static Pressure 0 One Sone is equivalent to 40 decibels Specifications subject to change without notice 13 MEASUREMENTS amp DIAGRAMS All are millimeter All inch measurements are converted from millimeters Inch measurements are estimated MODEL NO IN2636SQB Side View Bottom View 32 9 16 827 1 25 12 305 4 1 8 104 6 7 8 175 5 10 9 16 268 18 1 2 470 _ A 6 1 2 165 10 5 8 270 11 3 8 289 4 11 7 8 14 1 2 369 16 1 2 419 18 1 2 470 Front View Back View 30 518 777 24 609 30 5 8 777 6 7 8 175 5 1 1 2 38 N 9 1 lt 14 Stainless Steel Liner Sold Separately Model No INL36252A Model No INL42252A Model No INL48252A PARTS LIST MODEL NO IN2636SQB NO DESCRIPTION Bi 74 PART NO Hood
4. the insert Fig 6 Slowly remove the light support panel and unplug all the connections as shown in Fig 7 Install the hood casing support provided in the screw package Adjust the level of the locking mechanism according to the thickness of the base 3 4 thickness plywood recommended Tighten the screws included to secure as shown in Fig 8 Install the insert inside the custom wood frame Install the insert using the rear and front mounting holes which are located at 1 1 2 88mm up from the insert base Screws not included For a more secure installation use the mounting holes located on the side of the insert Make sure insert is secure before releasing Re install the light support panel Do not over tighten screws CAUTION MAKE SURE HOOD IS SECURE BEFORE RELEASING Figure 8 Figure 9 Figure 10 Final Assembly 29 Install the oil tunnel into recess support near rear of hood Refer to Figure 9 30 Install filters Angle baffle filter toward back of hood Push baffle filter up until almost level Slide forward into recess behind the front of hood 8 Lower baffle filter Slide back until it fits into resting position Refer to Figure 10 OPERATING INSTRUCTIONS This KOBE hood is equipped with five electronic push buttons with LED array six electronic button wireless control twin vertical centrifugal squirrel cage fan with stainless steel baffle filter ISC Integrated
5. Casing Oil Tunnel ISC IN2636 03 07 ISCO Baffle Filter Support Bracket 7 10 11 Spacers Spacers _____ Bottom Casing N2636 01 01 Control Unit Support N2636 02 08 Control Unit N2636 11 01 1 1 1 Light Support Panel Light Socket _ 77 53 dr _ 77 71 Le Le 2636 02 03 Light Decorative Ring ______ 71 71 1 _ 6 ___ IN2636 09 01 IN2636 07 02 IN2636 23 01 1 7 31 Optional Liner Sold Separately Rear Liner Section INL42252A__ IN2636 13 01 Rear Liner Section 1 48252 IN2636 14 01 os 2 3 5 1 19 2 22 23 24 25 26 2 28 29 30 Front Liner Section INL36252A IN2636 12 02 Front Liner Section INL42252A IN2636 13 02 Front Liner Section INL48252A IN2636 14 02 16 10 11 12 9 456 7 3 its Ss AN Var 55 Sold Separately Optional Liner 17 CIRCUIT DIAGRAM MODEL NO IN2636SQB i CONTROL BOARD ji PROCESSOR BOARD INDICATOR SENSOR 1 N3901VH DISCLAIMER 1 CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT REQUEST NAME AND SIGNATURE OF THE CARRIER S AGENT AND KEEP COPY TO SUPPORT YO
6. KOBE KOBE Brand Range Hood Model No IN2636SQB IN 026 SERIES INSTALLATION INSTRUCTIONS AND OPERATION MANUAL READ AND SAVE THESE INSTRUCTIONS CONTENTS IMPORTANT SAFETY INS TRUG TIONS cerieisa 1 COMPONENTS OF PACKAGE 3 INSTALLATION lla 4 FOR INSERT INSTALLATION sesini trenere lee 5 Preparation Before 5 Custom Hood Preparation 5 Emerinsiallatoni at ll 5 Wiring to Power SUDDIY 6 DUCT Work 6 Hood Preparation Before 6 Hood 7 ASSEM V 8 9 eo coer ee tenet tere 12 13 MEASUREMENTS amp DIAG gt 14 PARTO LIS 16 CIRCUIT DIAGRAM Grim 18 19 WARRANT aci 20 PRODUCTFREGIS TRATION ere ore tees a _ 22 READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING ALL WIRING MUST BE DONE BY A PROFESSIONAL AND IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES TEX 3099247 IMPORTAN
7. Sensor Control two bright 120 volt 40 watt socket light bulbs not included and one oil tunnel The five control buttons are Power Control On Off Speed Control High Medium Low 4 QuietMode Auto Control Timer Control and Light Control Refer to Figure 11 Time Baffle ISC Speed Power Indicator Change Indicator Indicator Indicator Indicator Auto Control Light Control Speed Control Timer Control Power Control Fig 11 Note For best results turn hood to QuietMode prior to any preparation or cooking Adjust speed as needed Power Control Press Power Control to turn On Off the hood Output Display 88 88 Speed Control Each press of speed button will cycle the fan through High Medium Low and QuietMode M Output Display will indicate 1 QuietMode Speed Low Speed Medium Speed High Speed Auto Control Press Auto Control to set the hood on auto sensor When gas or fluctuating temperature is detected hood will automatically turn ON Fan will turn to its highest speed and will turn OFF until gas is eliminated and temperature is reduced down to room temperature Temperature Higher than normal room temperature Output Display 88 88 Light Control Lights are control separately from ON OFF control Turning power off will not turn lights off Press Light control to turn lights ON Each press of Light Control will cycle the light
8. T SAFETY INSTRUCTIONS PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION AWARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY OBSERVE THE FOLLOWING 1 Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards including fire rated construction 2 When cutting or drilling into wall or ceiling be careful not to damage electrical wiring or other hidden utilities 3 Ducted fans must be vented to the outside a Before servicing or cleaning unit open the light panel and SWITCH POWER OFF AT SERVICE PANEL b Clean all grease laden surfaces frequently To reduce the risk of fire and to disperse air properly make sure to vent air outside DO NOT vent exhaust air into wall spaces attics crawl spaces or garages NOTE This warranty is invalid without an authorized agent s receipt or if unit is damaged due to misuse poor installation improper use mistreatment negligence or any other circumstances beyond the control of KOBE RANGE HOODS authorized agents Any repair carried out without the supervision of KOBE RANGE HOODS authorized agents will automatically void the warranty KOBE RANGE HOODS will not be held responsible for any damages to personal property or real estate or any bodily injuries whether caused directly or indirectly by the range hood A WARNING TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE TOP GREASE FIRE
9. UR CLAIM Upon acceptance of items owner assumes responsibility for its safe arrival Report damages to the carrier and file a claim immediately Failure to do so may result in the denial of your claim The carrier will furnish you with necessary forms for filing a claim DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY 2 PLEASE INSPECT CONTENTS OF PACKAGE S CAREFULLY UPON RECEIVING We must be notified in writing of any damages and or missing parts within the allocated days upon your receipt of package s Contact your local KOBE dealer or distributor or call KOBE for the time limit CLAIMS WILL NOT BE ACCEPTED AFTER THE ALLOCATED DAYS NOTE ITEMS WERE THOROUGHLY TESTED AND CAREFULLY PACKED IN OUR FACTORY BEFORE SHIPPING 3 Products must be returned in good working condition with ALL original parts and documentation packed in ALL original cartons fillers and shipping cartons A restocking fee of 25 will be charged for all approved return s EXCHANGES OR RETURNS MAY NOT BE ACCEPTED IF ANY PACKAGING IS MISSING 4 MAKE SURE TO INSPECT THE HOOD FOR DAMAGES AND DEFECTS BEFORE INSTALLATION Appearance flaws of the hood found after installation and not affecting hood performance is not covered under our warranty for returns or exchanges Service visits not covered under warranty will carry a service charge A Before Installation Return for exchange or refund please see above for acceptable returns B After Installati
10. d by the original purchaser during the warranty period the new owner is protected until expiration of the original purchaser s warranty See warranty section for complete warranty coverage information This appliance has been manufactured tested and inspected to the standards required by KOBE Range Hoods PLEASE MAIL IN YOUR WARRANTY REGISTRATION CARD AND PROOF OF PURCHASE TO KOBE Range Hoods 10505 Valley Blvd Suite 302 El Monte 91731 RECORD THE FOLLOWING INFORMATION FOR YOUR RECORD Model No Serial No Purchased Date Purchased From IMPORTANT PLEASE KEEP A COPY OF YOUR SALE RECEIPT OR INVOICE HANDY WHEN REQUESTING SERVICE 22 KOBE KOBE Range Hoods 10505 Valley Blvd Suite 302 El Monte CA 91731 USA htto www KOBERangeHoods com This KOBE hood is made for use in the USA and CANADA only We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that country Using a KOBE hood overseas is at your own risk and will void your warranty VER 070829
11. d to the range hood has been altered rendered illegible or removed if notice of the defect has not been given within the period applicable for failure of light bulbs or heat lamps d for physical damage e for surfaces damaged by use of improper chemical cleaning agents f if the appliance has been i subject to misuse abuse negligence accident incorrect installation or failure to follow the operating instructions connected to improper inadequate or faulty electricity service or exhaust ducts flues or duct cover or operated using incorrect or contaminated lubricants 11 installed maintained or operated otherwise than in accordance with the instructions furnished by KOBE Range Hoods including the improper use of detergents bleaches or cleaners 0 for damage to range hood during transit delivery installation or removal h for damage by or resulting from attempted repairs conducted by anyone other than our Authorized Service Agent I noise or vibration caused by improper installation of range hood and or damper 3 The purchaser shall be responsible for any expenses involved in making the range hood readily accessible for servicing and where the range hood is installed outside the main sales territory of the retailer or service territory of the nearest approved KOBE Range Hoods Agent as applicable for any traveling expenses and any costs of transporting the range hood or parts thereof to and from the dealer or Se
12. eaning solution gently rub off any stubborn spots Use dry soft towel to dry the hood 3 DO allow deposits to accumulate or remain on the hood 4 DO use ordinary steel wool or steel brushes Small bits of steel may adhere to the surface and cause rusting 5 DO NOT allow salt solutions disinfectants bleaches or cleaning compounds to remain in contact with stainless steel for extended periods Many of these compounds contain chemicals which may be harmful Rinse with water after exposure and wipe dry with a clean lint free cloth To Clean Baffle Spacer Filter Oil Tunnel and Oil Container AXCAUTION DRAIN FROM BAFFLES SPACER S FILTERS OIL TUNNEL S AND OIL CONTAINERS BEFORE OIL AND RESIDUE CAN OVERFLOW Cleaning Baffle Filters 1 Remove all baffles spacer s and oil tunnel s Follow directions page 7 in reverse 2 Discard oil and residue 3 Wash with warm soapy water Dry thoroughly before replacing Note Stainless Steel Baffles Spacer s amp Oil Tunnel are top rack dishwasher safe 12 SPECIFICATIONS MODEL SIZE COLOR CONSUMPTION AMPERE VOLTAGE NUMBER OF MOTORS FAN TYPE CENTRIFUGAL EXHAUST CONTROLS HALOGEN LIGHTS HOOD DIMENSION WXDXH OPTIONAL ACCESSORIES W XD X H HOOD WEIGHT Ibs Blower Air Capacity cfm Sone dB IN2636SQB 20 Gauge Commercial Stainless Steel 290W 2 5A 120V 60Hz 2 Twin Vertical Squirrel Cage Top 7 Round with Damper 5
13. gure 6 white and green to green See Figure 3 15 Store wires in the wiring box Note Connect all electrical wires before installing insert DO NOT turn on the power until installation is complete Duct Work Installation 16 Use 7 steel pipe follow building codes in your area to connect the ducting on the hood to the ductwork above Use duct tape to seal and secure joints as shown in Figure 4 17 Please refer to local codes for the usage of the damper not included lt 16 1 2 419 Figure 7 Hood Preparation Before Installation CAUTION If moving the cooking range is necessary to install the hood turn off the power in an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE 18 Determine and mark the centerlines on the base of the wood frame where the insert will be installed 19 Determine and make all necessary cuts in the wall or ceiling for the ductwork Note Install the ductwork 6 20 21 before installing the insert Determine the proper location for the Power Supply Cable Make a wiring access hole using a drill bit Install the wire cable and seal the gap around hole Cut out the opening where the insert will be installed Figure 5 Hood installation NOTE USE HAND TOOLS ONLY DO NOT OVER TIGHTEN SCREWS IT MIGHT CAUSED DAMAGED TO THE HOOD 22 23 24 29 26 27 28 Remove 4 screws located at the bottom of
14. intensity through high low and off Timer Control Press Timer Control to start timer Each press of Timer Control will increase by 1 minute on the display When Timer Control is pressed fan will automatically shut off after set time Timer range from 1 min to 99 mins To clear the timer press Timer Control twice Baffle Change Indicator The display will indicate when baffle filter needs cleaning Remove to clean the baffle filter To purchase replacement filters please contact your local KOBE dealer or call 626 350 1355 10 The six control buttons for the wireless remote control are Power Control On Off Light Control Speed Controls High Medium Low QuietMode Timer Control and Auto Control Refer to Figure 12 i O i ON OFF LIGHT SPEED TIMER CONTROL TIMER AUTO Fig 12 Power Control Press Power Control to turn On Off the hood Light Control Lights are control separately from ON OFF control Turning power off will not turn lights off Press Light control to turn lights ON Each press of Light Control will cycle the light intensity through high low and off Speed Control Press the Speed control to activate the Fan The KOBE hood will start on High speed Each press of the Speed Control button will cycle through the various speeds Press W to cycle from High Medium Low and QuietMode Press to cycle High QuietMode M Low Medium Ti
15. large rear section with pre cut for insert and a front section for a total adjustable depth between 23 and 25 3 4 8 Position the rear section of the liner so that it aligns with Wire Connector the back edge of the custom wood frame Use a pen to Figure 4 trace the outline of the pre cut area Remove the liner and proceed to Hood Preparation Before Installation 9 Install the rear section of the liner with 6 screws not included 10 Install the front section of the liner with 3 screws not included 11 Proceed to Hood Installation on Page 7 Wiring to Power Supply ASAFETY WARNING RISK OF ELECTRICAL SHOCK THIS RANGE HOOD MUST BE PROPERLY GROUNDED MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL Figure 5 CODES BEFORE CONNECTING WIRES SWITCH POWER OFF SERVICE PANEL AND LOCK SERVICE PANEL TO SB 777 gt PREVENT POWER FROM BEING SWITCHED ACCIDENTALLY 12 Temporarily wire the hood to test for proper operation before installing If the insert does not operate check Cut Out Dimension the circuit breaker or house fuse If the insert 1 still not working disconnect the power supply and check the continuity of all wiring connections 13 Connect electrical wires 14 Connect three wires black white and green to house wires and cap with wire connectors Connect wires according to their colors i e black to black white to Fi
16. mer Control Press Timer Control to activate Timer mode The Timer Indicator on the display will flash If Speed Timer Control button is not pressed within 6 seconds the unit will automatic exit the Timer mode The arrow will switch to speed function control During the Timer mode each press of will decrease the timer by 1 minute While each press of A will increase the timer by 1 minute Once the timer is set after 6 seconds the Timer Indicator will stop flashing and fans will automatically shut off after set time Auto Control Press Auto Control to activate the Integrated Sensor Control ISC feature 11 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE IS OPERATING Cleaning Hood Surface ACAUTION NEVER USE ABRASIVE CLEANERS PADS OR CLOTHS DO NOT USE PAPER TOWEL ON STAINLESS STEEL For optimal operation clean range hood and all baffle spacer filter oil tunnel oil container regularly Regular care will help preserve the appearance of the hood 1 Use only mild soap or detergent solutions Dry surfaces using soft cloth 2 hood looks splotchy stainless steel hood use a stainless steel cleaner to clean the surface of the hood Avoid getting cleaning solution onto or into the control panel Follow directions of the stainless steel cleaner Caution Do not leave on too long as this may cause damage to hood finish Use soft towel to wipe off the cl
17. on exchange or refund 19 WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods Inc warrants all products manufactured or supplied by it to be free from defects in workmanship and materials Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement at its option and subject to the terms and conditions stated below of any component part which its examination shall disclose to be so defective TWO YEAR WARRANTY SERVICE PERIOD Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our discretion replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase or original invoice handy for inspection If the range hood is sold by the original purchaser during the warranty period the new owner is protected until expiration of the original 5 warranty CONDITIONS The following conditions apply only in relation to the warranty expressly given in this certificate 1 This warranty applies only a within U S A and Canada to range hoods used for PRIVATE SINGLE FAMILY USE if used for COMMERCIAL or MULTIPLE FAMILY USE or other purposes warranty will be voided 2 Repair of any fault to be provided under this warranty shall not be provided a if the identification number attache
18. rvice Agent 20 4 purchaser must produce proof of purchase together with this warranty certificate when making the claim 5 Damages caused during shipment are not covered under our warranty CONSEQUENTIAL DAMAGE The warrantor is not responsible for any consequential damage SOME STATES DO NOT ALLOW THE EXCLUSION OF CONSEQUENTIAL DAMAGE SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IMPLIED WARRANTIES STATE LAW Any implied warranties including the implied warranty of merchantability and fitness for purpose imposed on the sale by the laws of the state of sale are limited to two year from the date of original purchase Some states do not allow limitations on the duration of implied warranties This warranty gives you specific legal rights and may also have rights which vary from state to state SERVICE For service contact KOBE Range Hoods 10505 Valley Blvd Suite 302 El Monte CA 91731 U S A Tel 626 350 1355 Fax 626 350 1976 Email customer service KOBERangeHoods com Website www KOBERangeHoods com 21 PRODUCT REGISTRATION Register Your Product Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE Range Hoods as applicable Keep proof of purchase original invoice handy for inspection If the range hood is sol
19. the hood if any e Use duct tape to seal joints between pipe sections CAUTION If moving the cooking range is Figure 2 necessary to install the hood turn off the power in an electric range at the main electrical box SHUT OFF THE GAS BEFORE MOVING A GAS RANGE And use a protective covering to protect cooktop and or countertop from damage Custom Hood Preparation 1 The custom hood frame must be sized to the shape and weight of the insert Refer to Measurements and Diagrams on Page 13 2 must have a sturdy base 3 4 inch thick plywood recommended to sustain the weight of insert 3 If an optional liner will be installed the side of the wood frame must be sturdy 3 4 inch thick plywood recommended Figure 3 4 is recommended to install rear amp front stud support not included Refer to Figure 2 The rear and front stud support 15 located 1 1 2 up from the base of the wood frame For safety purposes extra installation oa 1 holes the side of the insert are provided Prepare da ie the side stud support if needed Liner Installation 5 The custom wood frame must have a sturdy base to accommodate the cut out for the inset The base must be recessed to accommodate the height of the liner See liner dimension on Page 15 6 Secure the liner to the bottom of the base using screws not included appropriate for the size and material of your wood frame 7 Liner is made up of two sections a
20. y to turn on the lights or any type of appliance Open all doors and windows to disperse the gas If you still smell gas call the Gas Company and Fire Department right away CAUTION WARNING For general ventilation use only Do not use to exhaust hazardous or explosive materials and vapors To reduce the risk of fire use only metal ductwork Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and code authorities Activating any switch on may cause ignition or an explosion Due to the size and weight of this hood two people installation is recommended ELECTRICAL SHOCK HAZARD Can result in serious injury or death Disconnect appliance from electric power before servicing equipped the fluorescent light bulb contains small amounts of mercury which must be recycled or disposed of according to Local State and Federal Codes 5 Must Keep all material for returns or refunds Range Hood Box Liner Sold Separately A KOBE Range Hood B Warranty Registration Card H Front Section of Liner C Instruction Manual I Rear Section of Liner D Baffle Filter
Download Pdf Manuals
Related Search