KitchenAid KEYE850V User's Manual
Contents
1. FABRIC SOFTENER CLEAN SCREEN DISPENSER LIGHT behind control panel CYCLE CONTROL START BUTTON SELECTOR LINT SCREEN MODEL AND SERIAL NUMBER PLATE ELECTRONIC DRYNESS DRYER DRUM SENSOR LOADING DOOR Operating the Clothes Dryer Step 1 Add sorted load See page 7 for information on load sizes and sorting Step 2 Add fabric softener See page 7 for information on fabric softener use Step 3 Make selections a Select a cycle b Select a drying temperature See pages 10 11 for a description of cycle options Step 4 Close the dryer door The dryer will not operate if the door is open Step 5 Start the dryer See page 8 for instructions on Cycle Control Selector use Energy Saving Tips You can help save energy if you 6 Wash and dry several loads 1 Don t overload the dryer Load consecutively A warm dryer must be able to tumble freely for shortens drying time fastest most wrinkle free drying 7 Don t add wet items to a partially 2 Clean lint screen before each load dried load A build up of lint on the screen can 8 Don t open the dryer door lengthen drying time unnecessarily Warm air escapes 3 Don t overdry Use an automatic from the dryer into the room cycle to help prevent overdrying 9 Locate dryer in a warm area Remove load when dryer stops Drying time is longer in unheated 4 Dry only full loads Drying garages or utility rooms small loads wastes energy 10 Make sure the dryer is2. 2 3 4 Dry one slipcover at a time Remove from dryer while slightly damp Press pleating or ruffles if you wish Put slipcover on furniture while a trace of moisture remains for a smooth tight fit Snowsuits Jackets e Nylon e Polyester base Check for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations 1 Dry garment for about 10 minutes Remove turn inside out replace for another 10 minutes Remove and hang on a non rusting hanger to finish drying 2 Remove from dryer immediately after tumbling to help eliminate wrinkles Starched items 1 Dry starched clothes in a separate load 2 Always start with a cold dryer If drying more than one load dry starched items first 3 Turn dark articles inside out so starch spots will not show on the outside of the garment 4 Check load about 5 minutes after drying starts to be sure items are tumbling freely and that nothing is Sticking to the drum 5 Do not overdry starched articles starch will shake off the garment and be lost 6 For best results remove clothes from dryer at ironing dampness Place in a plastic bag and hold for at least 30 minutes to distribute moisture evenly before ironing 7 After drying a heavily starched load allow the dryer drum to cool then wipe it out with a damp cloth This guards against build up or starch transfer to articles dried in later loads 21 Washable Knits
3. Check label for fiber content then see Tinted and Non Colorfast Items Check label for fiber content then see Cycle Selection Chart on page 9 for Cycle Selection Chart on page 9 for cycle and temperature recommendations cycle and temperature recommendations 1 After drying is completed wipe the 1 Remove cotton and rayon knits 22 drum carefully to make sure there is no dye or lint that could be transferred to subsequent loads If dye transfer does occur follow the cleaning instructions on page 14 such as T shirts knit underwear when still slightly damp Stretch into shape and lay flat to finish drying Knits made of synthetic fibers polyester nylon acrylic etc and blends polyester cotton tend to pill Rubbing during wearing and laundering causes small balls of fiber to form on the surface Turn inside out to wash and dry Remove from dryer as soon as tumbling stops Do not overdry Overdrying can cause shrinkage and a build up of Static electricity Some items may need touch up ironing For Service or Assistance Follow These Steps 1 If your dryer should fail to operate review the following list before calling your dealer You could save the cost of a service call If your dryer does not run Is the power supply cord plugged into a live circuit with the proper voltage e Is the door closed tightly e Have you checked your home s main fuses or circuit breaker box e Did y
4. have wrinkles static electricity feel harsh and in some cases shrink Remove clothes with a slight trace of dampness Damp cotton and rayon knits should be laid flat to finish drying 10 Do not overload the dryer For minimal wrinkling clothes must be able to move freely in the dryer Overloading may result in greater lint residue on clothing due to poor air movement not allowing lint to reach the lint screen 11 Remove clothes from the dryer as soon as tumbling stops Hang or fold immediately Wrinkles may be set in clothes that are left in a warm dryer after it stops 12 Even items labeled Permanent Press may require touch up ironing due to decreased quality of permanent press finishes during the past few years 13 If the electric supply in your home is less than what is needed by your electric dryer drying will take longer See your Installation Instructions Drying S pecial Items Most garments and household textiles have care labels with laundering instructions Always follow label directions when they are available General drying instructions for some special washables are included in this section IMPORTANT Dry only clean items Soiled items can leave stains on the dryer drum These stains can be picked up by other items in the load Dryer heat may permanently set some stains Blankets and Woolens e Electric Blankets e Woolen Blankets e Washable Woolens Follow these directions only if
5. 1 Tumble dry with low heat on a less dry setting 2 Remove while slightly damp and air dry 3 Do not overdry Overdrying loosens the adhesive and causes fabrics to separate Cotton and Canvas Play Shoes 1 Place several bath towels in dryer to act as a buffer Use Air Tumble Cycle if rubber or foam rubber materials are part of shoe 2 Remove when damp dry Allow shoes to finish drying out of the dryer Curtains e Sheer panels Curtains made from synthetic fibers such as nylon or polyester dry quickly so they require only a few minutes of drying time 1 Start with a cold dryer 2 Use the lowest temperature setting on your dryer 3 Dry only two or three panels at one time Sheer curtains need plenty of room to fluff so be careful not to crowd the dryer 4 Remove from dryer while slightly damp Do not overdry Diapers and Baby Clothes Check label for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations 1 Do not dry soiled or stained items Dryer heat can permanently set stain 2 Remove diapers and cotton knit items from dryer while slightly damp so that they are easier to fold feel softer and shrink less 3 For convenient handling wash and dry small items in a mesh bag or pillow case Draperles Check label for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations 1 Remove weights and hooks 2
6. 3 Remove lint from shaded area see illustrations with a soft brush or vacuum cleaner ELECTRIC GAS 7 4 Replace panel Reconnect and level the dryer Cleaning the Dryer Interior Electric shock hazard Unplug the power supply cord or turn off the electrical power before cleaning the interior Failure to do so could result in electrical shock or injury Garments which contain unstable dyes such as denim blue jeans or brightly colored cotton items may discolor the dryer interior If discolored clean the interior with one of the following methods to avoid staining later load items 1 Powdered laundry detergent and very warm water Make a paste with detergent and water Apply paste to a soft cloth and scrub area until all excess dye is removed Wipe thoroughly with a damp cloth Tumble a load of rags to eliminate any remaining detergent OR 2 Liquid household cleaner Apply to stained area and rub with a soft cloth until all excess dye is removed Tumble a load of rags to eliminate remaining cleaner Vacation Care Unplug power cord or turn off electrical power at the circuit breaker or fuse box e For gas dryers close gas valve e Clean lint screen Common Drying Problems and Causes Problem Brown Stains rust Cause e dryer fabric softener e storing wet or damp clothes in dryer rusting Greasy Looking Spots e dryer fabric softener see page 7 for corr
7. KitchenAid MODEL KEYES850V Electric MODEL KGYES850V Gas USE and CARE GUIDE Table of Contents Important Safety Instructions 3 Ownership Registration 4 Clothes Dryer Features 5 Operating the Clothes Dryer 6 Energy Saving Tips 6 Load Preparation 7 SONING eee eee 7 LOAGING gae oieee cece 7 Load SES nrn sri rars 7 Fabric Softener 0 0 7 Make Selections 8 11 Select a Cycle 2 005 8 Select a Drying Temperature 8 Start the Dryer 8 Setting the Cycle Sentry 8 Cycle Selection Chart 9 Automatic Drying Cycles 10 Automatic Regular Heavy CYCIO siaina eienen 10 Automatic Permanent Press Cyle n aan eee 10 Air Tumble Cycle 1 Timed Dry Cycle 45 t1 Quick Press Option 11 Lint Screen ospea i prane 12 Clean Screen Light 12 Drum Light o n 13 Replacing the Drum Light 13 Drying Rack eee e es 14 Using the Drying Rack 14 Caring for the Clothes Dryer 15 Lint Removal 2 008 15 Cleaning the Dryer Interior 15 Vacation Care eee 15 Common Drying Problems and GaUSES in k aie ees 16 Drying Tips 17 18 Drying Special Items 18 22 For Service or Assistance 23 Warra
8. ON To reduce the risk of fire electric shock or injury to persons read the Important Safety Instructions on page 3 before operating your dryer Select a Cycle To set the desired cycle turn the Cycle Control Selector either left or right Stop turning when the marker points to the cycle and setting of your choice Refer to the Cycle Selection Chart on the next page for recommended cycle and temperature settings A description of each cycle can be found on pages 10 11 Select a Drying Temperature The Temperature Selector can be set anywhere on or between the four temperatures EXTRA LOW LOW MEDIUM and HIGH Refer to the Cycle Selection Chart on the next page for the recommended temperature settings CYCLE SENTRY SELECTOR CYCLE SENTRY TEMPERATURE SELECTIONS iow go OQ MeoUM Start the Dryer The dryer will start tumbling when the START button is pushed To stop the dryer open the door or turn the Cycle Control Selector to the OFF position To start the dryer close the door select a cycle if necessary and push START Setting the Cycle Sentry Your dryer will sound a signal to let you know when the cycle you have selected is finished The signal can be adjusted or turned off by setting the Cycle Sentry Selector anywhere on or between HIGH and LOW or on OFF The signal is helpful when drying permanent press synthetics and other items that should be taken out as soon as the dryer sto
9. To help prevent wrinkling dry only one or two drapery panels at one time depending on size 3 Remove from dryer as soon as it stops Some drapery fabrics may require little or no ironing if you remove them from the dryer while still slightly damp then smooth and rehang them Flame Retardant Finishes Some items you buy may have been treated with a flame retardant finish to improve their resistance to burning if they are exposed to flame Items treated in this manner will be clearly labeled To help reduce the loss or possible loss of the flame retardant qualities through continuous use and washing follow laundering instructions furnished by the manufacturer of the item Glass Fiber Materials Do not dry glass fiber materials in your dryer The fibers can break and remain in the dryer These glass particles could become imbedded in the fabric dried in the next load and cause skin irritation Heat Sensitive Fabrics Olefin e Polypropylene Plastics Rubber e Sheer Nylon Use Air Tumble Cycle only Drying in a heated dryer may damage the items or be a FIRE HAZARD Napped and Quilted Items e Chenille Fleecy Coats e Mattress Pads e Corduroy Check label for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations 1 Dry separately to avoid lint transfer 2 Remove from dryer while there is Still a trace of moisture chenille spreads may be dried comp
10. apment Do not tamper with controls Do not reach into the dryer if the drum is moving Do not let dust lint paper rags or chemicals pile up around or under the dryer Do not install against draperies or curtains Keep area around the exhaust opening free from accumulation of lint dust and dirt Do not install or perform any servicing unless you are qualified Improper installation repair or servicing may result in personal injury or fire hazard Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product Clean lint screen before each load SAVE THESE INSTRUCTIONS FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or fluids such as dry cleaning solvents or kerosene in or near your dryer or any other appliance The fumes can create a fire hazard or explosion FOR YOUR SAFETY If you smell gas 1 Open the windows 2 Don t touch electrical switches 3 Extinguish any open flame 4 Immediately call your gas supplier YOU ARE RESPONSIBLE FOR MAKING SURE THAT YOUR DRYER e Is installed by a qualified installer e Is properly maintained e Is properly installed and leveled in a well ventilated room on a floor that can support the weight e Is located in an area where the temperature is above 45 F 7 C Is properly connected to fuel and exhaust systems e Is used only for its intended func
11. build up on the lint screen To turn off the light turn off the dryer see page 8 for instructions and clean the lint screen as explained above Drum Light The Drum Light automatically comes 1 Open the dryer door and remove on inside the dryer drum when the light bulb cover by turning it dryer loading door is opened clockwise Replacing the Drum Light Unplug the dryer to avoid possible electrical shock e The bulb cover must be in place during dryer operation to prevent overheating and possible damage to fabrics Operating the dryer with the bulb cover removed can cause A wae the dryer to fail or create a 2 Remove the light bulb by turning it FIRE HAZARD counterclockwise 3 Replace the bulb with a 40 watt appliance bulb only 4 Replace the light bulb cover and lock it in place by turning counterclockwise Drying Rack The drying time will depend on how h moisture the items hold The The drying rack lets you dry items that muca you may not want to tumble For following chart suggests Cycle and Temperature Selections that match the e Pample sneakers stuified toys kitted different kinds of items that might wool etc best be rack dried The rack does not move but the drum turns around the rack Make sure nothing hangs over the edges of the rack Using the Drying Rack 1 Fit rear legs of rack into indentations in back wall of dryer 2 Lower front so legs rest on dryer ope
12. ect use e undiluted washer fabric softener drying soiled items Lint Shrinking joad not sorted correctly overloading overdrying e full lint screen e mistaken pilling for lint The rubbing that fabrics receive during normal wear and washing raises a surface fuzz called pilling Pills do not break away easily from the fabric and often collect lint Use a lint roller brush or cellophane tape to remove lint from pilled area Synthetics and blends tend to pill more than other fabrics Turn them inside out during laundering paper or tissue in pockets e overdrying e fabric type Slow Drying e load not sorted correctly e load type may require longer drying times e air movement slowed e dryer located in cold area e modern dryers are designed to use lower drying temperatures e if wash load ended with a cool rinse drying time will be slightly longer low spin speed e large items rolled or balled e load too large e low voltage e vent too long See Installation Instructions Static Electricity e overdrying e fabric type Some synthetics will normally produce static electricity Use dryer fabric softener see page 7 Stiff Harsh Fabrics e wash load was off balance and fabrics are very wet e line drying Wrinkling e using incorrect cycle selection overdrying e not removing clothes immediately after dryer stops tumbling e poor quality permanent pr
13. ed which helps prevent overdrying Cool Down Time The load tumbles without heat during the last 5 minutes of this cycle This helps keep wrinkles from setting in and makes the handling of hot load items easier Quick Press Option This setting is useful for removing wrinkles from items which have been packed in suitcases or closets 1 Set the Cycle Control Selector to QUICK PRESS 2 Set the Temperature Selector to MEDIUM 3 Push START The load will tumble with heat for 15 minutes followed by a COOL DOWN time of 5 minutes no heat For best results QUICK PRESS only a few items at a time As soon as the dryer stops fold or hang the items immediately Lint Screen 2 Roll the lint off the screen with your fingers Do not run your dryer with the lint screen loose damaged P blocked or missing Doing so can eag cause overheating damage to Bere fabrics and can be a FIRE ae HAZARD eee 3 Clean the lint screen before each load See A screen blocked by lint can increase drying time due to poor air flow and may be a fire hazard f To clean the lint screen 3 Do not rinse or wash the lint screen 1 Open the lid and pull the lint Water may clog the screen mesh screen straight out 4 Push the screen firmly back into place Clean Screen Light If you neglect to clean your lint screen the Clean Screen Light will come on The light indicates that air flow has been blocked by lint
14. ess finish on fabrics Drying Tips 1 If air movement is slowed down 6 Amount of moisture in load affects drying times will be longer A clogged lint screen will increase drying time CLEAN LINT SCREEN BEFORE EACH LOAD If this is your first automatic dryer you may notice a lot of lint on the lint screen After the first few weeks of use this surface lint from your clothes will be gone and lint on the screen will decrease e A clogged incorrectly installed or long length of exhaust duct will increase drying time Exhaust duct should be as short and as straight as possible See Installation Instructions Drying times will be longer and wrinkles may not be removed if dryer is located in a cold room such as a garage unheated basement or porch Dryers should not be operated in rooms below 45 F Drying times will be longer when your dryer is exhausted inside Exhausting your dryer indoors Is not recommended The molsture and lint may cause damage to woodwork furniture paint wallpaper and carpet housecleaning and possible health problems and FIRE HAZARD from lint collected inside the dryer See Installation Instructions for additional information Loads rinsed in cold water will take slightly longer to dry than loads rinsed in warm water Large loads take longer to dry than smaller loads of the same fabric Check to see that large items such as sheets are not rolling or balling up I
15. eturn them to the dryer and reset for more drying time Remember that ticking will feel dry long before feathers are dry IMPORTANT Feather pillows dry very slowly and must be dried completely to prevent mildewing It may take 11 2 to 2 hours Dry no more than two pillows at one time Pillows and Stuffed Toys Polyester e Foam Rubber Kapok 1 Be sure covers are securely stitched 2 Use Air Tumble Cycle only DO NOT dry foam rubber items on heat setting of dryer Use air setting or line dry Drying in a heated dryer may damage the items or be a FIRE HAZARD Plastic and Rubber Items e Shower Curtains e Tableclothes Baby Panties Use Air Tumble Cycle only 1 Drying in a heated dryer may damage the items or be a FIRE HAZARD Set the Cycle Control Selector to the Air Tumble Cycle for 20 minutes Place 3 or 4 dry towels in the dryer with these items to help absorb the moisture Scatter Rugs Check label for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations 1 2 Dry one medium size rug or two smaller rugs at one time Clean the lint screen Use Alr Tumble Cycle only for drying rubber backed rugs Drying rubber backed rugs with heat may damage the rubber backing and may be a FIRE HAZARD Slipcovers Check label for fiber content then see Cycle Selection Chart on page 9 for cycle and temperature recommendations l
16. exhausted 5 Separate light from heavyweight properly to the outside Keep fabrics for faster more even drying exhaust duct clean and check flapper to make sure it opens and closes freely Load Preparation For best results the following steps should be taken to prepare your clothes for drying e Empty all pockets A small scrap of paper can cause a lot of lint Turn pockets of heavy items inside out for even drying Remove heat sensitive trim that can be damaged by drying e Tie strings and sashes so they won t tangle e Close zippers snaps and hooks to avoid snagging other items Remove any sharp or heavy objects that could damage the dryer drum e Turn lint givers and takers and dark items inside out to help prevent lint pickup Put small items baby socks handkerchiefs in a small mesh bag for easier removal Check garments to make sure all spots and stains were removed during the wash If stains were not removed do not tumble dry Heat may permanently set the stain Sorting Items properly sorted for washing are usually properly sorted for drying For best results e Separate heavy fabrics denim and towels from light fabrics synthetics and permanent press Separate lint givers towels and chenille from lint takers corduroy synthetics and permanent press When possible turn lint givers inside out Separate dark from light colors and colorfast from non colorfast Loading L
17. f balling or rolling up occurs rearrange items drying time e Large or heavy items such as towels jeans and bedspreads need longer drying times due to the higher level of water retained in the fabrics Polyester and synthetics hold much less moisture Clothes that were washed with low spin speeds best for permanent press and knit fabrics will have retained more moisture than clothes washed with high spin speeds Loading practices will affect drying times e Overloading will increase drying time due to restricted air movement and uneven drying may result e Uneven drying may also result from loading heavy and light items together Light items will overdry and heavy items will not be dry When drying a load with different kinds and weights of fabrics use the setting suggested for the lightest fabric e Small loads may ride around the drum without tumbling Add one or two lint free towels to help with tumbling This dryer is designed for the care of modern fabrics e Drying temperatures are lower than in older models because high heat can damage modern fabrics e This dryer has a cool down time at the end of drying cycles see Cushioned Heat Drying System and Cool Down Time page 10 This helps reduce wrinkling but the total cycle may be longer than you are used to 9 Avoid overdrying Every fabric has a natural moisture content If clothes are overdried this moisture is removed Clothes may
18. isfied with the action taken e Contact the Major Appliance Consumer Action Panel MACAP MACAP is a group of independent consumer views at the highest levels of the major appliance industry e Contact MACAP only when the dealer authorized servicer or KitchenAid Inc have failed to resolve your problem Major Appliance Consumer Action Panel 20 North Wacker Drive Chicago IL 60606 e MACAP will in turn inform us of your action 23 KitchenAid Clothes Dryer Warranty LENGTH KITCHENAID KITCHENAID OF WARRANTY WILL PAY FOR WILL NOT PAY FOR ONE YEAR FULL Replacement parts and A Service calls to WARRANTY repair labor to correct 1 Correct the installation FROM DATE OF defects in materials of the dryer PURCHASE or workmanship Service 2 Instruct you how to use must be provided by an the dryer authorized KitchenAid servicing outlet Replacement parts to correct defects in materials or workmanship 3 Replace house fuses or correct house wiring 4 Correct house plumbing TWO YEAR LIMITED WARRANTY ONE YEAR FULL PLUS SECOND YEAR LIMITED FROM DATE OF PURCHASE FIVE YEAR LIMITED WARRANTY ONE YEAR FULL PLUS SECOND THROUGH FIFTH YEAR LIMITED FROM DATE OF PURCHASE TEN YEAR LIMITED WARRANTY ONE YEAR FULL PLUS SECOND THROUGH TENTH YEAR LIMITED FROM DATE OF PURCHASE B Repairs when dryer is used in other than normal home
19. letely 3 Smooth reshape and air dry before putting away 4 Choose shrink resistant quilted items for best results Permanent Press Fabrics 1 See page 9 for cycle and drying temperature settings which will give clothes the special treatment they need Permanent press items need a period of heated drying to release wrinkles followed by tumbling in room temperature air This helps prevent new wrinkles from setting in 2 Dry smaller loads Items should tumble freely 3 Remove clothes from dryer as soon as tumbling stops Garments left in the dryer drum will become wrinkled 20 If clothes remain in the dryer after it has stopped tumbling use the Quick Press Option to help restore the pre set shape of the clothes see page 11 4 Place garments on hangers or fold immediately after removal from dryer 5 Well constructed permanent press items will be smooth and wrinkle free when washed and dried correctly Poorly finished or constructed permanent press may need touch up ironing especially where seams pucker Pillows e Feather Down 1 Check ticking for holes or weak seams where feathers or filling could escape Make necessary repairs before putting pillows in the dryer 2 Use highest temperature setting until pillow is fluffy and free of lumps 3 Stop drying occasionally and shake items to redistribute feathers 4 Check pillows at end of drying time If they are not completely dry r
20. ning 3 Put wet items on top of the rack Leave space between items so air can reach all surfaces 4 Close the door and set the time desired for drying Suggested To Rack Dry Suggested Cycle Temperature Wool Sweaters Block to shape and lay flat on the rack TIMED DRY LOW Stuffed Toys or Pillows Cotton or polyester fiber filled TIMED DRY HIGH Foam rubber filled AIR TUMBLE Sneaker or Canvas Shoes AIR TUMBLE Drying with heat may damage the foam rubber and may be a FIRE HAZARD Caring for the Clothes Dryer For maximum use satisfaction and longer dryer life follow these guidelines e Do not place sharp or heavy objects on or in the dryer Damage to the finishes may result e To clean dryer exterior wipe with a soft damp cloth e Never leave wet or damp laundry in your dryer Damage to clothing or the dryer drum may result Lint Removal Lint can gather inside the dryer and create a fire hazard This lint should be removed by a qualified person at least once every two years or more often depending on dryer usage Electrical shock hazard Unplug the power supply cord or turn off the electrical power e Do not put hands inside the cabinet e Make sure the dryer is cool Failure to do so could result in electrical shock Injury or damage 1 Remove back panel for electric models or the lower access panel for gas models 2 Avoid damaging wires thermostats funnel or igniter
21. nty BACK COVER 1988 KitchenAid Inc Important Safety Instructions To reduce the risk of fire electric shock or injury to persons when using the dryer follow basic precautions including the following Read all instructions carefully for important information before using your appliance Your dryer should be installed in an area protected from weather Your dryer should be connected to the right kind of outlet electrical supply and grounding See the Installation Instructions for complete information Never dry articles in the dryer that have been spotted cleaned washed or soaked in gasoline wax paint or other flammable fluids The fumes can create a fire hazard or explosion Always hand launder and air dry fabrics containing these materials Never use heat to dry articles containing foam rubber or similarly textured rubber like materials Fire hazard and damage to some materials can result from operating the dryer with the lint screen loose damaged or missing e allowing lint to build up inside the dryer and exhaust system The exhaust duct and interior of your dryer should be cleaned by a qualified technician at least once every two years See page 15 for lint removal instructions Never allow children to play on or in the dryer Close supervision is necessary when this or any appliance is used near children When discarding an old dryer always remove the door to prevent accidental entr
22. oad Sizes A proper size washer load is generally a proper size dryer load For best drying results do not dry more than two full size sheets in one load even if more than two sheets were in same washer load Sheets need more space for proper air movement and maximum drying Fill out the load with small items of the same type fabric Fabric Softener Use only fabric softeners specifically labeled as not being harmful to the dryer A fabric softener dispenser has been provided behind the control panel on the left side e For best results put a sheet of fabric softener on top of the load before Starting the dryer Do not add the fabric softener sheet after the cycle has started Instant heat may cause the fabric softener to spot fabrics e If the fabric softener sheet becomes tangled or wrapped in one item during tumbling a clear grease like spot can result If fabric softener has caused a stain wet the stain and rub with liquid detergent or bar soap then wash the item Some fabric softeners may 1 cause rust or residue deposits in the dryer and on fabrics Clog the lint screen Cause your dryer to overheat and or fail to shut off Static cling can be reduced by not overloading Service or performance problems caused by the use of any product not manufactured by KitchenAid Inc are the responsibility of the manufacturer of that product Make Selections START PUSH TO START START BUTT
23. or can be set to indicate the degree of dryness you choose for the clothes being dried A sensor in the back of the dryer drum senses the moisture in the load When the selected dryness has been reached the dryer shuts off For the first few loads set the Cycle Control Selector to the middle line between VERY DRY and LESS DRY in the cycle of your choice If the result is drier than you like set the selector Closer to LESS DRY the next time you dry a similar load If the result is not dry enough set the selector closer to VERY DRY the next time you dry a similar load Cushioned Heat Drying System In both automatic cycles the dryer automatically reduces the heat setting during the last 7 minutes of the cycle COOL DOWN which helps prevent overdrying takes over after the Cushioned Heat Drying System is finished Cool Down Time During the last 5 minutes of the Automatic Regular Heavy Cycle and the last 7 minutes of the Automatic Permanent Press Cycles the dryer will tumble without heat This helps keep wrinkles from setting and makes the handling of hot load items easier 10 CYCLE SENTRY TEMPERATURE SELECTIONS LOW OFF The Cycle Control Selector will not move until the clothes load is almost dry or until the COOL DOWN portion of the cycle has been reached After COOL DOWN the selector will move to the OFF position and tumbling will stop Automatic Regular Heavy Cycle This cycle can be used for heav
24. ou push the START button If your dryer does not heat Remember the Air Tumble Cycle does not use heat and the last few minutes of all cycles do not use heat e Is the gas turned on e An electric dryer requires two fuses or a circuit breaker If one fuse is blown the dryer may run but the heat may not operate properly If drying times seem too long Is the lint screen clean e See the Slow Drying section in the Common Drying Problems and Causes Chart page 14 e Are you using a 208 volt outlet Drying times will be longer If longer drying times are unsatisfactory a higher wattage element is available Contact KitchenAid Customer Relations or your local dealer 2 If the problem is not due to one of the above items e Call your dealer or an authorized service in your area e All service should be handled locally by the dealer from whom you purchased the unit or an authorized KitchenAid servicer 3 In the event you are unable to obtain the name of a local authorized KitchenAid servicer e Call KitchenAid Customer Relations TOLL FREE 1 800 442 1230 e A Customer Relations representative can recommend a qualified service company in your area e If you must call or write please provide Model Number Serial Number Date of Purchase and a complete description of the problem Write to Customer Relations Department KitchenAid Inc PO Box 558 St Joseph MI 49085 0558 4 If you are not sat
25. ps tumbling TEMPERATURE SELECTOR CLEAN SCREEN TIMED DRY a 3 tess pry REGULAR HEAVY AIR TUMBLE t PERMANENT PRESS CLEAN SCREEN LIGHT CYCLE CONTROL SELECTOR C yele Selection Chart Suggested Suggested Type of Load Cycle Temperature Cottons Linens EXTRA HEAVY Bedspreads mattress pads quilts HIGH HEAVYWEIGHT Towels jeans corduroys work MEDIUM clothes AUTOMATIC MEDIUMWEIGHT Sheets pillowcases cotton REGULAR HEAVY MEDIUM underwear diapers LIGHTWEIGHT Batistes organdies lingerie LOW Permanent Press Synthetics and Blends HEAVYWEIGHT Work clothes jackets raincoats AUTOMATIC MEDIUM MEDIUMWEIGHT Shirts play clothes sheets PERMANENT MEDIUM slacks PRESS LIGHTWEIGHT Lingerie blouses dresses LOW Knits HEAVYWEIGHT Cottons rayons blends T shirts AUTOMATIC MEDIUM slacks shirts PERMANENT LIGHTWEIGHT Synthetics polyester acrylic and PRESS LOW blends lingerie blouses dresses Delicate Fabrics Sheer curtains 2 or 3 panels gauze lace AUTOMATIC EXTRA PERMANENT LOW PRESS damage them or be a FIRE HAZARD Rubber Plastic Heat Sensitive Fabrics AIR TUMBLE FOAM RUBBER Pillows bras stuffed toys 20 30 min PLASTIC Shower curtains tablecloths 20 30 min RUBBER BACKED RUGS 20 30 min OLEFIN POLYPROPYLENE SHEER NYLON 15 20 min Automatic Drying Cycles REGULAR HEAVY and PERMANENT PRESS are both automatic cycles The Cycle Control Select
26. the manufacturer recommends automatic drying 1 Select HIGH temperature setting 2 To absorb moisture and dry the blanket rapidly place three or four dry towels in the dryer turn dryer on and preheat for three to five minutes This preheating helps absorb moisture and dry blankets rapidly to avoid pilling caused by long tumbling 3 Place blanket in dryer with warm towels Set the dryer control for 20 minutes 4 Check the blanket after 10 minutes of drying Remove from the dryer while still damp to guard against overdrying which may cause shrinkage and harshness 5 Place blanket on flat surface or over two lines to finish drying Stretch blanket gently to original shape 6 When blanket is completely dry brush gently to raise nap Press binding with cool iron if needed IMPORTANT We do not recommend tumble drying knitted woolens For best results trace the outline of the garment on a clean piece of paper After washing block by finger pressing gently to this outline Let the garment dry to this shape Blankets e Cotton e Rayon e Synthetics 1 Tumble dry using Permanent Press cycle and temperature selections see Cycle Selection Chart on page 9 2 Dry completely Do not overdry 3 Some cotton and rayon blankets stretch during washing Drying completely restores to original size 4 Remove from dryer as soon as it stops Bonded or Laminated Items If manufacturer recommends automatic drying
27. tion e Is not run where there may be explosive fumes e Is not used by children or anyone unable to operate it properly ALWAYS unplug the power supply cord or turn off electrical power before attempting to service the dryer Shut off the gas valve if yours is a gas dryer ALWAYS shut off the gas valve before leaving on vacation NEVER operate the dryer if e it is not working properly i e too noisy too hot it is damaged e parts are missing i e door latch e all panels are not in place e lint screen is not in place See the Installation Instructions for complete information Ownership Registration Please fill out and mail your Ownership Registration Card packed with the Use and Care Guide This card will enable us to contact you in the unlikely event of a product safety notification and assist us in complying with the provisions of the Consumer Product Safety Act Return of this card is not necessary to validate your warranty You must provide proof of purchase or installation date for in warranty service Write down the following information You will need it if your dryer ever requires service Model Number Serial Number Date Purchased Date Installed Dealer s Name Address Phone Model and serial numbers are located on a plate in the upper left hand corner of the door opening Clothes Dryer Features CYCLE SENTRY TEMPERATURE SELECTOR SELECTOR
28. use Damage resulting from accident alteration misuse abuse improper installation or installation not in accordance with local electrical or plumbing codes Replacement parts for any electrical element on electric models or any burner on gas models Rust through protection on cabinet assembly D Any labor costs during the limited warranties Replacement of the dryer drum if it rusts through due to defective materials or workmanship E Replacement parts or repair labor costs for units operated outside the United States F Pickup and delivery This product is designed to be repaired in the home KITCHENAID INC DOES NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so this exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state KitchenAid Inc St Joseph Michigan 49085 U S A Part No 3387335 Printed in U S A 1988 KitchenAid Inc
29. y and mediumweight cotton items such as towels blue jeans corduroys bedspreads and linens Automatic Permanent Press Cycle Use this cycle to dry permanent press items Knits and other synthetic fabrics If you are unable to unload the dryer within 5 minutes after it stops tumbling the Smooth Guard Feature takes over automatically to protect your clothing from wrinkles SMOOTH GUARD tumbles the load without heat every 5 minutes continuing up to 40 minutes or until the door is opened to remove the clothes SMOOTH GUARD is only featured in the Automatic Permanent Press Cycle Ow FT MEDIUM HiG t 4 j EXTRA 1OW H HIGH CLEAN SCREEN TIMED DRY AIR TUMBLE Air Tumble C yele The dryer does not use heat when the Cycle Control Selector is set on Air Tumble Use this cycle to fluff bedding and pillows to dust draperies and clothing and to dry heat sensitive items such as plastics foam or sponge rubber sneakers or stuffed toys Drying plastic or rubber items with heat may damage the items or be a FIRE HAZARD Timed Dry Cycle Use the Timed Dry Cycle for any load you want to dry by time Turn the Cycle Control Selector to the amount of time you want the load to tumble dry from 10 to 70 minutes Cushioned Heat Drying System The dryer automatically reduces the heat setting during the last 7 minutes of the cycle COOL DOWN takes over after the Cushioned Heat Drying System is finish
Download Pdf Manuals
Related Search