Keys Fitness ST-IB User's Manual
Contents
1. never holding your breath during an exercise Perform exercises consistently with proper technique and pass through a full range of motion Increase resistance by adding heavier weights Decrease resistance by using lighter weights Always use a spotter for safety Avoid over training You should be able to carry on a conversation while exercising After an exercise session Cool down with slow stretching cycling or walking EXERCISE DEFINITIONS Sets A set is one complete routine of exercises Complete 1 3 sets for each exercise Repetitions referred to as reps Is the number of times you perform an exercise in a row We recommend beginning with 6 reps and increasing up to 12 reps as indicated below Novice Start with one set of 8 12 reps Once you can complete the entire set of 12 reps con secutively progress to the intermediate level Intermediate Complete 2 sets of 8 12 reps once you can complete two sets of 12 reps con secutively progress to the advanced level Advanced Complete 3 sets of 12 reps DISCLAIMER Keys Fitness is not responsible for the misuse of any of its products or for any injury sustained while using any Keys Fitness product The consumer uses any or all of Keys Fitness products at their own risk AWARNING 1 The max user weight limit for this unit is 300 pounds 2 The max total weight limit for this unit is 600 pounds user weight lifting weight Assemb ly 3 StrengthTrainer Thank you2. to identify the hardware used in the assembly The number in paren theses is the reference number of the part Note Some hardware may be pre installed in some parts M6 x 20mm M8 x 60mm Bolt 59 Screw 41 M8 x 10mm dad M6 x 40mm Screw 48 M4 x 16mm M10 x 60mm Carriage Bolt 29 Screw 57 m M8 x 65mm Bolt 46 M10 Washer 43 M10 x 65mm Bolt 30 M8 x 70mm Bolt 71 M8 Washer 50 Ol M10 x 70mm Bolt 33 M6 Washer 54 M10 x 70 Bolt Set 55 M10 Nylon Locknut 58 M10 x 95mm Bolt 64 NX QU M10 x 145mm Bolt 53 5 Assembly 3 StrengthTrainer Step 1 Insert four M10X60mm carriage bolts 29 up through the bottom of the right stabilizer 2 Attach the right upright 4 to the right stabilizer 2 with indicated carriage bolts and nylon locknuts 58 Repeat to complete the assembly of the left stabilizer 1 and left upright 3 Note Make sure the recessed areas around the holes on stabilizers are on the bottom Figure 1 NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 6 Assembly 3 StrengthTrainer Step 2 Attach the crossbar 5 to the right upright 4 using two M10X120mm bolts 14 an upright plate 15 and two M10 nylon locknuts 58 Repeat to complete the assembly for the left upright not shown Figure 2 lt gt 58 Step 3 Attach the right rear support 7 to the right stabilizer 2 us
3. 777 202 00791 202 00778 202 00774 202 00779 219 00633 219 00630 202 00780 228 00264 202 00781 202 00786 202 00783 202 00181 202 00181 219 00629 202 00784 202 00485 202 00785 210 00626 210 00625 202 00787 202 00445 202 00788 210 00624 202 00789 202 00263 202 00263 202 00790 202 00782 202 00792 202 00630 202 00794 202 00795 219 00635 219 00634 202 00793 206 00510 202 00797 202 00796 202 00290 215 00219 DESCRIPTION LEFT STABILIZER ST IB RIGHT STABILIZER ST IB LEFT UPRIGHT ST IB RIGHT UPRIGHT ST IB CROSSBAR ST IB LEFT REAR SUPPORT ST IB RIGHT REAR SUPPORT ST IB FRAME ST IB ADJUSTMENT TUBE ST IB SEAT FRAME ST IB FRONT STABILIZER FRONT LEG ST IB ARM CURL POST ST IB HEX BOLT M10 120 UPRIGHT PLATE ST IB UPRIGHT COVER ST IB BACKREST FRAME ST IB LEG LEVER ST IB WEIGHT TUBE ST IB CURL PAD ST IB SEAT ST IB BACKREST ST IB FOAM PAD ST IB PAD TUBE ST IB 19MM ROUND INNER CAP ST IB SQUARE BUSHING ST IB SAFETY SPOTTER ST IB Curl Bar Pin ST IB M10 x 60MM CARROAGE BOLT ST IB BOLT M10X65 CURL BAR ST IB 25MM x 40MM INNER CAP ST IB HEX BOLT M10X70 57MM SQUARE INNER CAP ST IB 25MM x 50MM INNER CAP ST IB 25MM Square INNER CAP ST IB 50MM x 100MM INNER CAP ST IB 48MM ROUND INNER CAP ST IB WEIGHT REST ST IB SEAT ADJUSTMENT PIN ST IB M6X20MM SCREW ST IB SEAT CARRIAGE ST IB M10 WASHER ST IB 25MM ROUND INNER CAP ST IB POP PIN ST IB HEX BOLTS M8 65 HEX BOLTS M8 65 OLYMPIC AD
4. APTOR ST IB M6x40MM SCREW ST IB NYLON NUT M8 AOLIN M8 WASHER ST IB SMALL SPRING CLIP ST IB LARGE SPRING CLIP ST IB M10x145MM BOLT ST IB WASHER M6 IRONMAN M10 x 70MM BOLT Set ST IB KNOB ST IB M4 x 16MM SCREW ST IB NYLON LOCKNUT M10 NYLON LOCKNUT M10 M8 x 60MM BOLT ST IB M8 x 10MM Set SCREW ST IB 17MM x 9MM Spacer ST IB ROUND OUTER CAP 25MM 50MM SQUARE INNER CAP ST IB M10 x 95MM BOLT ST IB BUSHING ST IB BUMPER ST IB 32MM ROUND INNER CAP ST IB PAD CAP ST IB 64MM Square INNER CAP ST IB 50MM x 75MM INNER CAP ST IB BOLT M8X70 OWNER S MANUAL ST IB 22 PST zal a Hee ene qu an Professor p O Ra Ens epe mcer ence HHNNEH StrengthTrainer Exploded View 3 StrengthTrainer 3 StrengthTrainer Exploded View Warranty Information StrengthTrainer Residential and Personal Use Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS FULLY AND CAREFULLY BEFORE USING YOUR KEYS FITNESS EOUIPMENT BY USING THE EOUIPMENT YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING TERMS AND CONDITIONS Frame Lifetime Parts 90 days Limited Warranty This Limited Warranty applies in the United States and Canada to Products manufactured or distributed by Keys Fitness Products L P under the Keys Fitness Keys brand name as used herein the Product or Products The warranty period to the original purchaser is listed above and commences on the date o
5. StrengthIrainer ST IB Owner s Manual International Bench Customer Service 888 340 0482 3 StrengthTrainer 4009 Distribution Drive Suite 250 Garland TX 75041 www keysfitness com SERIAL TAG IS LOCATED ON THE FRAME Model Name ST IB Date of Purchase 215 00219 Serial Number 08 07 RevA Table of Contents Important Safety Information Assembly Getting Started Hardware Identifier Assembly Steps Adjustments Seat Adjustments Backrest Adjustment Attachments Curl Bar Olympic Plate Adapter Arm Curl Post Weight Rests and Safety Spotters Warm Up Exercises Parts List Exploded Views Warranty 3 StrengthTrainer UJ 22 23 25 3 StrengthTrainer Important Safety Information Please read all instructions carefully before using this product SAFETY TIPS Consult with your physician before engaging in any vigorous exercise Know your heart rate and or pulse as well as your physician recommended heart rate training zone Proper medical clearance is recommended for anyone beginning an exercise program especially if you are 35 years of age or older or suffer from heart respiratory problems Warm up before any exercise program with 8 minutes of aerobic like activity followed by stretching from head to toe Wear comfortable clothes that allow freedom of movement and are not tight or restricting Wear comfortable shoes made with good support and non slip soles Breathe naturally
6. XCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE THIS IS THE ONLY EXPRESS WARRANTY APPLICABLE TO KEYS BRANDED PRODUCTS KEYS NEITHER ASSUMES NOR AUTHORIZES ANYONE TO ASSUME FOR IT ANY OTHER EXPRESS WARRANTY Notes 3 StrengthTrainer 26 Notes 3 StrengthTrainer 27 StrengthTrainer Customer Service 888 340 0482 Keys Fitness Products 4009 Distribution Drive Suite 250 Garland TX 75041
7. ace a solid structure such as a wall wath your left foot ahead af your right baes straaght ahead Bend your left knee press your haps forward and lean mio the wall Keep bath heels down your nght leg Strat and you left knee aver your ankle Hold far 20 seconds repeat three ta five Umes with each leg Slanding Quii eps Stretch Steady yourself wath one hand With the other grab autade leg at ankle keeping body straight from knee tn hip Genthy pull foot up and towards the but Incks until you feel a stretch along the front of the thigh Thigh should be pulled strasaght back and not drift ta outade Hold 20 20 seconds For varia hon grab oppasite ankle i e grab right ankle wath left hand Do Ewo In three repetitions per leg 21 Face the wall with your left foot ahead of yaur right baes ahead Bend both knees press your hips forward and lean inta the wall Keep bath heels down and bath knees in ne with your feet Hold for 20 seconds repeat three In five Games with each leg Parts List ST IB PARTS LIST REV A REF PARTS 223 01233 223 01220 223 01230 223 01229 223 01234 223 01231 223 01226 223 01223 219 00636 223 01221 223 01222 223 01224 223 01225 202 00172 219 00626 219 00627 223 01227 223 01228 219 00628 228 00261 228 00262 228 00265 228 00263 219 00625 202 00775 206 00511 219 00631 219 00632 202 00776 202 00425 223 01232 202 00773 202 00294 202 00
8. ce providers Service quotes costs and scheduling will be strictly dependent on service provider rates and mutual consumer provider service agreements Keys is not responsible for any service repair costs accrued through the use of authorized Keys service providers at your request or out of the limited warranty period without written consent from Keys beyond the limitations outlined on this warranty 25 Missing Cosmetic Parts 30 Days Replacements and Returns If after a reasonable number of attempts a defect has not been repaired or the Product is deemed non repairable by Keys technical service and support staff Keys based on a case by case review may opt to replace the Product or recommend an alternate resolution such as a warranty buy out Product cost subject to deduction of a reasonable charge for usage or a credit Keys as a manufacturer reserves the right to replace the Product with a Factory Reconditioned Product that meets or exceed standards comparable to those of the replaced Product The warranty covering the replacement Product shall expire on the date the original warranty for the replaced Product would have expired unless otherwise determined by Keys Conditions and Restrictions This warranty DOES NOT A cover shipping and handling charges export taxes custom duties and taxes or any other charges associated with transportation of the parts or Product beyond the initial courtesy period of 60 days from
9. e weight rests or safety spotters WARNING Always place both weight rests 39 and safety spotters 27 at the same height Make sure the locking bars are securely wrapped around the uprights before setting a barbell on them 18 Warm Up Exercises 3 StrengthTrainer EXERCISE GUIDELINES WARNING Before beginning this ar any program you should consult your physician This ix especially important for ndnadual over Ehe age of 35 or individuals wth pre existing health problems Flexibiliby 5 a key bb fines Stretch all major muscle groups at least two bo three times per week after a 5 tn 10 minute warmup Stretch just Ep the pomt of a gentle bog If you have bark jaint or other health problems talk to your dactar first Prone on Elbows Supine Lumbar Rotation Knees to Chest Lie on your ztamach with Le on your back with yaur Le on your back Bend your your feet together Rest knees bent Keeping your knees and lift your feet off the an your forearm with your knees together and yaur shoul floor Grasp your knees wath elbows directly under your ders against the floor your Yow arms and pull your knees shoulders Relax lower hack knees to ane side until you feel toward your chest Hold for 20 and abdomen into floor Hold stretch in your back or hap seconds Repeat three tn five for 30 60 seconds ar until Hold fnr 30 60 seconds ar until mes muscles feel kaser muscles feel kaser Repeat an appombe side Cat and Came
10. f original purchase of the product unless otherwise authorized by Keys Keys warrants that the Product purchased from Keys or from an authorized Keys Fitness reseller dealer for residential or personal use only unless otherwise authorized by Keys in writing is free from defects in Materials and Workmanship relevant to the functionality of the Product at initial startup under normal use and during the applicable warranty period unless otherwise determined by Keys This warranty excludes expendable parts if primary cause for warranty claim is wear Expendable parts pertain to components on the Product that are prone to normal wear and tear These items vary by Product and can include but not limited to hand grips skid pads pedals pedal straps poly v belts console overlays toggle switch button overlays luster free or dull ekg plates decals and any other items that are not essential to the operation of the Product unless otherwise determined by Keys This warranty extends only to you the original purchaser It is not transferable to anyone who subsequently purchases or receives as a gift the Product from you Your sales receipt showing the date place of purchase and serial number if applicable of the Product is your proof of purchase and may be required by Keys any time a warranty parts or service claim is made or if no warranty record exists for the product Exclusive Remedies During the warranty period listed ab
11. for purchasing the Strength Trainer International Bench The quality product you have chosen was designed to meet your needs for cardiovascular exercise Before you start please read the Owner s Manual and become familiar with the operation of your new unit Remember to take the time to perform stretching exercises provided in this manual to help avoid injury Getting Started The Strength Trainer International Bench will require some assembly Unpack the box in a clear area Remove packing material Do not dispose of packing mate rial until assembly is complete and unit is working properly Place the unit on a clean level surface for assembly Before assembling the unit should be placed as close as possible to its final location If you are missing any parts or hardware please call Keys Fitness at 1 888 340 0482 Tools have been provided to assist with product assembly Keys Fitness recommends for two people to assemble the unit As you assemble the bench make sure all parts are oriented as shown in the drawings The included hex key grease packet and the following tools not included are recommended for assembly Hex Key Included Two Adjustable Wrenches Rubber Mallet Flat Head Screwdriver Phillips Head Screwdriver et Safety Spotter S Arm Curl Pad Leg Extension w Curl Bar SN 7 Olympic Adapter 4 Assembly 3 StrengthTrainer Hardware Identifier See the drawings below
12. g extension Olympic Plate Adapter To use olympic weights press the 48mm round inner cap 38 into the olympic adapter 47 Secure the olympic adapter 47 to the weight tube 19 using M8X10mm set screw 60 Make sure the set screw 60 is on the bottom of the adapter Secure the weight plates with included large spring clip not shown WARNING Do not place more than 150 pounds on the weight tube Secure the weights with spring clips 17 Attachments 3 StrengthTrainer Arm Curl Post Remove the 64mm sguare inner cap 69 from front leg 12 Insert the curl post 13 into the front leg 12 and align the holes Secure the curl post 13 with the curl post knob 56 Note Make sure that the knob is fully tightened When performing exercises that do not reguire the curl pad 20 remove the curl post 13 and store it on the storage tube on the right stabilizer 2 Reinsert the 64mm 69 square inner cap into the front leg Weight Rests and Safety Spotters To use a barbell not included with the weight bench first move the weight rests 39 and safety spotters 27 to the correct height for the exercise to be performed Engage the locking bars around the left and right uprights Note The weight rests 39 and safety spotters 27 can be inserted onto the other side of the left and right uprights for sguat exercises Locking Bar WARNING Do not place more than 300 pounds including barbell on th
13. ing the indicated M10X60mm car riage bolts 29 two washers 43 and two M10 nylon locknuts 58 Secure the right rear support 7 to the right upright 4 using two M10X65mm bolts 30 two M10 washers 43 and two M10 nylon locknuts 58 Repeat to complete the assembly for the left side not shown NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 7 Assembly 3 StrengthTrainer Step 4 Attach the front leg 12 to the front stabilizer 11 with two M10X95mm bolts 64 and two M10 nylon locknuts 58 Figure 4 Step 5 Position the frame 8 so that the hexagonal holes are on the bottom Attach the frame 8 to the crossbar 5 using three M10X70mm bolts 33 two M10 washers 43 and three M10 nylon locknuts 58 Figure 5 Hexagonal Holes NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 8 Assembly 3 StrengthTrainer Step 6 Tighten the T handle 45 into the seat carriage 42 Pull the T handle 45 out as far as it will go and slide the seat carriage 42 onto the frame 8 Attach the front leg 12 to the frame 8 using two M8X60mm bolts 59 two M8X65mm bolts 46 six M8 washers 50 and four M8 nylon locknuts 49 Figure 6 Step 7 Set the pins on the adjustment tube 9 into a set of brackets located on the left and right uprights 3 amp 4 9 Assembly 3 StrengthTrainer Step 8 Attach the tether o
14. l Turn your body toward the left away from Ehe wall and your ex tended arm until you feel a stretch Hold far 20 secans repeat three ta five limes with each arm Wrst Hexnr Extend your night arm in frant af vau palm down elbow Strat your fingertips toward the floor by bencdang at the wrist Using your left hand pull your night palm ta ward you gently Hold for 20 seconds repeat three ta five Umes with each arm Firtonmis Stretch Lie on your back Bend your right knee and lift it hallway your chest Grasp your knee with your left hand and pull iE toward your left shaul der keeping both buttacke agamet the floor Hold for 70 seconds repeat three to five Umes with each leg 20 Triceps Stretch Place your right hand behind our head palm facing yaur head With your left hand grasp your right elbow and pull downward until yau feel a stretch in the back af your night arm Hold for 20 ser ands repeat three to five Umes with each arm Grain Alductors Stretch Sitting with your hack sirai bring the sales af vour feet together Let your knees lower mar the floor Hold fnr 30 60 secancds ar until muscles feel looser Warm Up Exercises 3 StrengthTrainer WARNING Before beginning this ar any Program you should consult your physician This ix especially important for individuals over Ehe age of 35 or individuals wth pre existing health problems Cali Stretch F
15. l Cervical Sale Hends Rest an yaur hands and Tilt your head gently tward In a mnih continuous mo knees Round your back by ane shoulder keeping your Bon make a cirde with yaur cantrachimg your abdomaal shoulders level and your face shoulders Rage them up muscles and tucking in your painted straight ahead Hold towards your ears pull them pehe hold far five seconds far five seconds then bit your together behind you lower Then allow your back ta saq head toward the other shoulder them ta a resting posion toward the floor as you lift and hoki for five seconds Re then roll them forward Repeat your chest and head hold peat limes on each sade 10 times far five seconds Repeat the cambenatin 10 tires 19 Warm Up Exercises 3 StrengthTrainer WARNING Before beginning this ar any program you should consult your physician This is especially important for individual over Ehe age of 35 or individuals wth pre existing health problems Wrst Extensor Extend your night arm in frant af yau with your palm up and your elbow straight Point your fingertaps toward the floor by bending at Ehe wrist Uang your left hand pull the back of your right hand to ward you gently Hold for 20 seconds repeat three to five mes with each arm m One Arm Pectoralis Stretch Stand against an immatle structure ke a wall a tree While faang the wall raise your night hand out ta yaur mide at chest height palm agame the wal
16. lever 18 and secure with the curl bar pin 28 Next attach the tether on the curl bar pin 28 to the leg lever 18 using a M4X16mm screw 57 Step 16 Attach a curl bumper 66 to curl bar 31 using a M4X16mm screw 57 Figure 16 Step 17 Tighten all hardware from the previous steps using the appropriate tools 14 a E U lt ational Bench Intern CONGRATULATIONS embly of your Strength Trainer mpleted ass have co You Adjustments 3 StrengthTrainer Seat Adjustments To move the seat 21 loosen the T handle 45 and pull it out as far as it will go Slide the seat carriage 42 to the desired position and release the T handle 45 back into the bench frame 8 Retighten the T handle 45 See Figure A To adjust the angle of the seat 21 remove the seat adjustment pin 40 Insert the pin into Figure A Figure Backrest Adjustment First move the seat pad to the desired position see the Seat Pad Adjustment section Next move the adjustment tube 9 to the desired height Make sure the pins on the adjustment tube are inserted into the brackets on the left and right uprights 3 amp 4 Finally rest the backrest on the adjustment tube Attachments 3 StrengthTrainer Curl Bar Attachment Attach the curl bar 31 to the leg lever 18 and secure by inserting the curl bar pin 28 Note You will need to remove the curl bar when using the le
17. ly 3 StrengthTrainer Step 12 Apply grease to the barrel of the M10X70mm bolt set 55 Next attach the leg lever 18 to the front leg 12 and secure using the bolt set 55 Make sure the barrel of the bolt set 55 is inserted through both sides of the bracket on the front leg 12 Note Do not overtighten the bolt set the leg lever must pivot easily Figure 12 Step 13 Insert a pad tube 24 into either hole on the front leg 12 Slide a foam pad 23 onto each end of the pad tube 24 Insert a pad tube 24 into a hole on the leg lever 18 Slide a foam pad 23 onto each end of the pad tube 24 Press a pad cap 68 into each end of the tube Note It is recommend you use a rubber mallet to gently hammer the caps into place Repeat for other pad tube 24 Figure 13 NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 12 Assembly 3 StrengthTrainer Step 14 Insert a weight rest 39 into the right upright 4 and secure by engaging the locking bar around the upright Insert a safety spotter 27 into the right upright 4 and secure by engaging the locking bar around the upright Repeat for left side Figure 14 Step 15 Attach the curl pad 20 to the curl post 13 using two M6X20mm screws 41 Figure 15 NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 13 Assembly 3 StrengthTrainer Attach the curl bar 31 to the leg
18. n the seat adjustment pin 40 to the seat frame 10 using an M4X16mm screw 57 Attach the seat pad 21 to the seat frame 10 with four M6X20mm screws 41 Figure8 21 Step 9 Attach the backrest pad 22 to the two backrest frames 17 with four M6X40mm screws 48 and four M6 washers 54 Note Do not fully tighten the screws yet Figure 9 22 NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 10 Assembly 3 StrengthTrainer Step 10 Apply a small amount of grease included to an M10X145mm bolt 53 Attach the seat frame 10 and the backrest frames 17 to the seat carriage 42 using the M10X145mm bolt 53 two M10 washers 43 and an M10 nylon locknut 58 Note 1 The seat pad 21 has been removed from the drawing to clarify the installation to the seat carriage 42 2 Do not overtighten the nylon locknut the seat and backrest frames must pivot easily Insert the seat adjustment pin 40 through the seat frame 10 and tube located on the seat carriage 42 Tighten the four M6X40mm screws 48 that were installed in Step 9 Figure 10 Step 11 Attach the weight tube 19 to the leg lever 18 using an M8X70mm bolt 71 two M8 wash ers 50 a 17mmX9mm spacer 61 and a M8 nylon locknut 49 Place the 25mm round outer cap 62 onto the end of the weight tube 19 Figure 11 NOTE Hand tighten bolts and nylon nuts until machine is fully assembled 11 Assemb
19. nance g service by anyone other than Keys or an authorized Keys warranty service provider h floods fires earthquakes lightning strikes power surges and other unavoidable acts of nature j residential mis wires or k incorrect setup installation or assembly Should any Product submitted for warranty parts replacement be found ineligible under the terms outlined on this warranty an estimate for parts purchase if available can be furnished at your request Parts is herein defined exclusively for all intents and purposes and pertaining to this Limited Manufacturer Warranty as components or Materials essential to the functionality of the Product Lifetime of a Product is herein defined exclusively for all intents and purposes and pertaining to this Limited Manufacturer Warranty as the time period 7 years beyond the end of production cycle of a Product in question Disclaimer and Release EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY KEYS MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR THE E
20. original date of purchase of the Product B extend to Products not purchased from Keys or from an authorized Keys reseller C extend to Products purchased from online auction sites D cover any extended additional or third party warranties if not offered exclusively by Keys in writing E cover Products installed at fee based facilities commercial environments gyms homes used as wellness centers etc F cover Products installed in light institutional environments non fee based facilities include for example and not be way of limitation fire houses police departments rehab centers hospitals clinics apartment complexes club houses etc G cover service calls to correct installation perform maintenance or instruct owners on how to use the equipment or H cover a Product on which the serial number has been purposefully or accidentally defaced or removed and there is no proof of purchase available if serial number is applicable unless authorized by Keys in writing or otherwise stated on this warranty This Limited Warranty becomes void for Products that have been damaged or rendered defective as a result of a accident misuse or abuse including but not limited to exceeding the Keys listed maximum weight limit b use of parts not manufactured or sold by Keys c modification of the Product d normal wear and tear e operation on incorrect power supplies f failure to perform or performing improper mainte
21. ove Keys will repair a Product by correcting any minor issues either by phone or online support that might be causing the Product failure Should a technical service and support representative be unable to correct the issue Keys may replace the parts with new parts or at the option of Keys with serviceable used parts that are equivalent to new parts in performance that become defective malfunction or otherwise fail to conform to this Limited Warranty under normal use Replacement parts shall be warranted for 30 days from the shipment reception date or through the end of the replaced part warranty period whichever is longer Any replacement parts required past the warranty period listed above shall be subject to purchase at retail price plus any added shipping and handling charges associated to the delivery of the part Note that replacement parts may be available only through the lifetime as defined of the Product In conforming to this warranty Keys as the manufacturer reserves the right to change manufacturers or vendors of any part to cover the existing warranty Keys may also provide service if deemed necessary and if applicable at no charge to you during and not to exceed the service warranty period listed above in an attempt to repair the Product Should the Product require service at your request or out of the limited warranty period Keys can furnish contact information for local to your area Keys authorized servi
Download Pdf Manuals
Related Search