Home
John Deere LPBST-35JD User's Manual
Contents
1. above If the material is coming out right or left during operation adjustment of this lever should be made to center the material distribution pattern behind the vehicle Your broadcast spreader has a patented feature to allow you to adjust for centering One Side Only Spreading MX34607 The directional control handle can be used for adjusting the material spread pattern when spreading near sidewalks planting beds etc With the handle adjusted to the left side B the directional control handle only operates with 90 shut off of material to the right side of the vehicle as shown in the illustration above Removing 6 SERVICE Operational Tips e Always operate your spreader with the speed limit for which it was designed 3 mph e When backing carefully back straight to avoid jack knifing which could result in damage to equipment e Only tow your spreader behind vehicles for which it was designed riders and lawn and garden tractors e Do not load the hopper with more than the maximum weight capacity of 79 kg 175 Ib e When spreading ice melters pin both wheel hubs for better traction e When spreading seed fertilizer etc insert only one spring locking pin in either the right or left wheel hub e Break up any lumps as you fill the hopper e Do not use on windy days especially when spreading fine grass seed or herbicides e Optimum hitch height is
2. lever to OFF setting 2 If parts are disassembled assemble all parts MX34612 Picture Note View from top and rear of spreader 3 Move the flow control assembly lever to 10 setting A 4 Adjust the two nuts B on directional control plate C in or out together so the flow control plate D is fully open E Tighten nuts together 5 Move flow control assembly back and forth and to the OFF setting Flow control plate will move freely and be in closed position Troubleshooting Using Troubleshooting Chart If you are experiencing a problem that is not listed in this chart see your authorized dealer for service When you have checked all the possible causes listed and you are still experiencing the problem see your authorized dealer Troubleshooting Chart IF CHECK Flow control lever does not snap into flow control pointer Tighten 1 4 x 2 1 2 in hex bolt on flow control lever assembly Not enough or too much fertilizer dispensed Calibrate the plates Loosen 1 4 x 2 1 2 in hex bolt on flow control lever assembly Flow control lever hard or will not operate Take control plates apart and clean plates out with water Troubleshooting 8 SPECIFICATIONS IF CHECK Ibs 1000 Flow Materials square Control Fan
3. may impair its function and safety e Securely anchor all loads to prevent loads from falling e Distribute load evenly for safe travel and unloading of cart e Do not obstruct the operator s view during use Towing Loads Safely e Stopping distance increases with speed and weight of towed load Travel slowly and allow extra time and distance to stop e Total towed weight must not exceed limits specified in towing vehicle operator s manual e Excessive towed load can cause loss of traction and loss of control on slopes Reduce towed weight when operating on slopes e Never allow children or others in or on towed equipment e Use only approved hitches Tow only with a machine that has a hitch designed for towing Do not attach towed equipment except at the approved hitch point e Follow the manufacturer s recommendations for weight limits for towed equipment and towing on slopes Use counterweights or wheel weights as described in the machine operator s manual e Do not turn sharply Use additional caution when turning or operating under adverse surface conditions Use care when reversing e Do not shift to neutral and coast downhill Protect Bystanders e Keep bystanders away when you operate a towed attachment e Before you back machine and attachment look carefully behind attachment for bystanders Keep Riders Off Towed Attachment Keep riders off of a towed attachment Riders on a towed attachment are subject to i
4. 18 23 cm 7 9 in Service Maintenance Tips e The key to years of trouble free service is to keep your spreader clean and dry e Never allow material to remain in hopper for extended periods of time e Should rust develop sand lightly and then paint area with enamel e Periodically check all fasteners for tightness e Rinse dry inside and outside of spreader after each use Move flow control as you rinse to avoid build up of material Annual Maintenance MX39211 1 Remove snap ring A 5 8 in flat washer B wheel C washers D if installed and axle bearing E MX39212 2 Remove spring locking pin F and slide axle G out from support frame H 3 Clean parts 4 Lightly lubricate both axle bearings 5 Remove two locknuts l and support tube J from bolts on frame 6 Remove 1 8 x 1 in cotter pin K agitator L and 3 8 in ID O ring M and transmission N 7 Clean fan O Service 7 TROUBLESHOOTING MX39213 8 Remove three screws P that secures control plate assembly Q 9 Remove 1 4 x 2 1 2 in bolt R 1 4 in flat washer S 1 4 in lockwasher T and 1 4 in nut U and flow control assembly V from support tube J MX34611 10 Separate parts as shown 11 Clean thoroughly using soap and water 12 Assemble parts reverse order of removal Calibration 1 Move the flow control assembly
5. IMPORTANT Avoid damage To avoid transmission damage do not adjust slot in transmission bracket forward or rearward The slot will self center as hardware is tightened MX39208 4 Make sure transmission bracket J is on top of nuts K on hex bolts L and install control support tube M onto bolts L Secure with 5 16 in locknuts N Tighten locknuts MX39209 5 Install hitch clevis brackets O onto tow tube end P with two 5 16 x 2 in carriage bolts Q and 5 16 in locknuts R as shown Tighten hardware 6 Install 1 2 x 2 1 2 in hitch pin S and 1 8 in spring locking pin small T through end of clevis brackets as shown Installing Installing the Spreader 1 Park machine safely See Parking Safely in Safety section MX39210 2 Remove 1 8 in spring locking pin A and 1 2 x 2 1 2 in hitch pin B from hitch clevis C of spreader 3 Pull spreader forward and position hitch clevis to straddle machine rear hitch plate or drawbar not shown Align all hitch pin holes then install hitch pin down through hitch clevis and machine hitch securing with 1 8 in spring locking pin small Installing 5 REMOVING Removing Removing the Spreader 1 Park machine safely See Parking Safely in the Safety section 2 Remove all materials from the hopper before removing spreader from machine A CAUTION Avoid injury Keep
6. JOHN DEERE WORLDWIDE COMMERCIAL amp CONSUMER EQUIPMENT DIVISION Broadcast Spreader LPBST 35JD OMM157122 B7 OPERATOR S MANUAL JOHN DEERE All information illustrations and specifications in this manual are based on the latest information at the time of publication The right is reserved to make changes at any time without notice COPYRIGHT 2007 Deere amp Co John Deere Worldwide Commercial and Consumer Equipment Division All rights reserved Previous Editions COPYRIGHT 2004 2005 2006 North American Version Litho in U S A INTRODUCTION Introduction Using Your Operator s Manual Read this entire operator s manual especially the safety information before operating This manual is an important part of your machine Keep all manuals in a convenient location so they can be accessed easily Use the safety and operating information in the attachment operator s manual along with the machine operator s manual to operate and service the attachment safely and correctly If your attachment manual has a section called Preparing the Machine it means that you will have to do something to your tractor or vehicle before you can install the attachment The Assembly and Installation sections of this manual provide information to assemble and install the attachment to your tractor or vehicle Use the Service section to make any needed adjustments and routine service to your attachment If you have any questions o
7. does not turn Find or replace missing spring locking pin in feet Setting when pulling wheel or transmission at3 Check position of fan fan driver and lock clip mph 3 2 3 5 Bayer Lawn Fertilizer Plus Weed Control II 30 3 4 sg 3 8 3 5 Bayer Season Long Grub Control Specifications y 9 2 9 3 Bayer Season Long Grub Control LPBST 35JD Broadcast Spreader y 3 f 2 3 6 3 5 Bayer Lawn Starter Fertilizer 20 27 5 Dimensions Size maximum weight 000 eeeee eens 79 kg 175 Ib 3 2 3 5 Bayer Lawn Fertilizer Plus Crabgrass Preventer Capacity ses ices Sais wees eds leg weld sink o wala 0 10 cu m 3 5 cu ft 30 3 4 Wheels and Tires 33 0 x 10 2 cm 13 x 5 in Turf tread 3 3 5 Eliminator Ant Flea and Tick Killer Granules Tire Inflation 0 0 cece eee ee eee 138 kPa 20 PSI T 2 5 3 Eliminator Ant Flea and Tick Killer Granules Specifications and design subject to change without notice rae 3 2 3 Eliminator Ant Flea and Tick Killer Granules Flow Control Settings for Specific Products 2 3 5 Eliminator 5 Diazinon Killer Granules 7 S Howard Johnsons All Purpose Fertilizer 8 8 8 A d id iniurv i 3 CAUTION Avoid injury chemicals canbe dangerous 7 5 Howard Johnsons All Purpose Fertilizer 10 10 10 Avoid injury to operator or bystanders e Read chemical container label for mixing and handling 7 5 Howard Johnsons All Purpose Fertilizer 12 12 12 instructions A Material Safety Data Sheet MSDS should be supplied by the ch
8. e end of bearing fits into square hole of support frame assembly NOTE Add or delete washers O to reduce axle side to side movement 7 Install two 5 8 in flat washers O onto each side of axle Lubricate the axle ends and wheel sleeve bearings Install wheel P 5 8 in flat washer Q and snap ring R onto end of axle IMPORTANT Avoid damage Use only one spring locking pin open to engage the wheels When using the spreader on ice the opposite wheel can be pinned for added traction Use of two pins on dry pavement may result in damage to the unit 8 Install spring locking pin open S through inside hole in wheel rim and axle onto either side of axle Install Agitator and Controls NOTE The four tabs on the fan should be compressed against the fan driver If pressure is not applied the fan connection will be loose resulting in poor performance MX34601 1 Adjust fan A upwards with fan driver B and lock clip C on shaft as close to bottom of hopper D without touching during operation Make sure fan driver engages the four plastic tabs on the bottom of fan Assembly 4 INSTALLING MX39207 2 Install 3 8 in ID O ring E on transmission shaft F until seated on bottom of hopper G 3 Install agitator H and secure with 1 8 x 1 in cotter pin I through top loop in agitator and hole in transmission shaft as shown
9. emical dealer and provides proper safety 5 45 lronite 1 0 0 THEE 4 3 5 Klay Soft Pelletized Gypsum Soil Conditioner Wear proper clothing and safety equipment while handling or applying spray chemicals 3 3 Klay Soft Pelletized Gypsum Soil Conditioner Wear a full covering of clothing protective goggles and 2 2 5 Klay Soft Pelletized Gypsum Soil Conditioner rubber gloves 4 45 Lesco Pre M 0 86 Plus Fertilizer 25 0 7 Prohibit all smoking drinking and eating around chemicals When filling tank never allow end of water hose to contact 4 2 4 Lesco Starter Fertilizer 18 24 12 chemical mixture 4 2 3 5 Lesco Turf Fertilizer 24 2 11 The following is a list of flow control settings for specific products available 4 3 5 Lesco Weed and Feed for use with the spreader Some products may not be available in all areas i Flow control settings are based on 3 mph forward speed 8 6 5 Master Turf Ultimate Tall Fescue Blend z 4 5 Master Turf Ultimate Tall Fescue Blend Ibs 1000 Flow Materials square Control 8 6 5 Milorganite 6 2 0 feet Setting at 3 16 8 Milorganite 6 2 0 mph 3 2 3 5 Miracle Gro Lawn Fertilizer Plus Weed Control 10 6 All American All Purpose Fertilizer 10 10 10 28 3 3 3 8 5 Bayer Season Long Grub Control 3 6 3 5 Miracle Gro STarter Lawn Fertilizer 20 27 5 2 9 4 Bayer Season Long Grub Control 3 1 3 Miracle Gro STarter Lawn Fertilizer 29 3 4 3 3 5 Bayer Complete Insect Killer 9 6 5 5 Ortho Lawn Insect Killer Granules 2 3 Bayer Complete I
10. hands feet and other body parts away from under drawbar 3 Remove 1 8 in spring locking pin from hitch pin 4 Hold spreader tow tube to remove pressure from hitch pin then remove hitch pin from hitch clevis and rear hitch plate or drawbar on machine 5 Pull or push spreader backward to disengage hitch clevis from machine hitch install hitch pin in hitch clevis for storage and secure with 1 8 in spring locking pin Storing The spreader can be tipped upright and stored against a wall using less space 1 Remove any loose material from hopper and fan using a brush and garden hose The spreader should be clean and dry before storing 2 Roll spreader to desired storage area lift hitch clevis to pivot spreader to vertical position Operating Daily Operating Checklist m Check for loose or missing hardware LI Make sure all connections are tight LI Make sure attachment responds properly to controls m Check for debris build up that could obstruct proper motion of the spreader control components Operating the Spreader The Fan speed and the spread width are controlled by the speed of the vehicle The recommended operating speed is slightly faster than that of a brisk walk 3 mph 3 mph is equal to the vehicle traveling 40 ft in nine seconds The flow control assembly operates the flow control plate The flow control assembly is marked 0 closest to 10 fully open The position selected determine the amount
11. hoice Lawn Food 29 3 4 3 2 Vigoro Insect Control Plus Fertilizer 6 5 5 Sam s Choice Starter Fertilizer 20 27 5 3 6 45 Vigoro Starter Fertilizer 3 6 4 Sam s Choice Starter Fertilizer 20 27 5 3 5 3 5 Vigoro Turf Fertilizer 29 3 4 4 5 5 Scotts Classic Grass Seed Fall Grass Seed Mix 3 3 Vigoro Ultra Turf Winterizer 22 3 14 2 3 5 Scotts Classic Grass Seed Fall Grass Seed Mix 3 2 45 Vigoro Weed and Feed 2 3 2 5 Scotts Grubex 4 5 5 Wal Mart Gardens Kentucky Bluegrass Grass 3 1 4 Scotts Grubex Season Long Grub Control Seed Specifications 10 GETTING QUALITY SERVICE Ibs 1000 Flow Materials square Control feet Setting at 3 mph 2 3 5 Wal Mart Gardens Kentucky Bluegrass Grass Seed 8 7 Wal Mart Gardens Kentucky 31 Tall Fescue 4 5 5 Wal Mart Gardens Kentucky 31 Tall Fescue 3 2 3 5 Wal Mart Weed and Feed 28 3 3 a Flow Control Settings are based on 3 mph forward speed b The products listed are the property of their respective owners and are not the property of nor recommended by Deere and Company Calibration Settings If the product you are using is not listed in the flow control setting table use the this calibration guide to set the flow control Calibration guide information is also provided on the hopper decal of the spreader Using application information on product package find the calibration setting in the following guide and set calibration control lever Adjust spread patte
12. me D with two 5 16 x 3 in hex bolts G and 5 16 in hex nuts H Tighten hardware and torque bolts to 30 Nem 22 lb ft or one complete turn after finger tight MX34596 1 Install six 1 4 x 1 3 4 in hex bolts A and 1 4 in thrust washer B Install Transmission and Wheels through top of hopper C and through support frame D as shown Secure bottom of bolt with 1 4 in locknut E To avoid damage to plastic do not overtighten hardware MX38960 1 Install lock clip A and fan driver B with small diameter lip of driver toward the bottom as shown 2 Slide fan C onto transmission assembly D shaft over top of fan driver Move lock clip fan driver and fan downward so top of fan is approximately 12 7 cm 5 in E from top of transmission shaft Assembly 3 ASSEMBLY MX38962 3 Raise transmission into position by installing transmission fan shaft into center hole of the control plates on the bottom of the hopper Lower transmission bracket F onto bolts G 4 Install axle H through support frame assembly I with offset hole near center of axle installed toward left side J of spreader MX34599 MX21908 Picture Note View from rear of spreader 5 Slide axle until lengths K are equal and install spring locking pin closed L into left side hole M MX38963 MX21907 6 Install axle bearing N onto each side of axle so squar
13. njury such as being struck by objects and being thrown off the attachment during sudden starts stops and turns Riders obstruct the operator s view resulting in the attachment being used in an unsafe manner Keep riders off of hitch bracket Avoid Injury From Drawbar Before you disconnect an attachment from machine hitch plate Unload attachment e Stop attachment on level ground e Stop machine engine e Lock machine park brake e Block attachment wheels e Make sure hands feet or other body parts are not under drawbar Introduction 1 Assembly Parts in Kit Qty 1 Hardware Pack Qty 4 2 ASSEMBLY Qty MX38959 Description Fan A Hopper Assembly and Control Support B Tube Tow C Clevis Hitch D Wheel E Axle F Support Frame Hopper G Transmission and Brace H Description Locknut 5 16 in Nut 5 16 in Assembly 2 Description Bolt Hex 5 16 x 3 in Carriage Bolt 5 16 x 2 in Hitch Pin 1 2 x 2 1 2 in Spring Locking Pin 1 8 in Small Washer Flat 5 8 in Spring Locking Pin Open Spring Locking Pin Closed Locknut 1 4 in Bolt Hex Stainless 1 4 x 1 3 4 in Cotter Pin 1 8 x 1 in Bearing Axle Snap Ring E Type Washer Thrust 1 4 in O Ring 3 8 in ID Spring Agitator Stainless Lock Clip Driver Fan ASSEMBLY Assemble Hopper to Frame MX38961 2 Install tow tube F onto support fra
14. nsect Killer 4 8 3 5 Ortho Lawn Insect Killer Granules 3 2 5 Bayer Power Force Multi Insect Killer 2 4 2 Ortho Lawn Insect Killer Granules 2 2 Bayer Power Force Multi Insect Killer 1 2 1 5 Ortho Lawn Insect Killer Granules 3 3 Bayer Grub Control 4 4 Ortho Max Insect Killer for Lawns 2 2 5 Bayer Grub Control 2 3 Ortho Max Insect Killer for Lawns Specifications 9 SPECIFICATIONS Ibs 1000 Flow Materials Ibs 1000 Flow Materials square Control square Control feet Setting feet Setting at 3 at3 mph mph 1 2 Ortho Max Insect Killer for Lawns 2 3 3 5 Scotts Grubex Season Long Grub Control 10 6 Parkers Super Soilife Lawn and Garden Fertilizer 1 4 2 5 Scotts Lawn Fungus Control 10 10 10 2 7 4 Scotts Lawn Fungus Control 6 5 4 5 Parkers Super Soilife Lawn and Garden Fertilizer 16 4 8 2 2 3 5 Scotts Pure Premium Kentucky Bluegrass Mix 3 6 3 5 Pennington Lawn Starter Fertilizer 18 24 6 1 1 3 Scotts Pure Premium Kentucky Bluegrass Mix 10 7 Pennington Master Turf High Traffic Lawn Seed 2 5 4 Scotts Pure Premium Sun and Shade Grass Seed Mixture Mixture 5 5 5 Pennington Master Turf High Traffic Lawn Seed 1 25 3 Scotts Pure Premium Sun and Shade Grass Seed Mixture Mixture 8 7 Pennington Master Turf Shady Lawn Seed 3 6 3 5 Scotts S
15. of material to be broadcast The higher the number the heavier the application of material Flow control setting for many of the common fertilizers insecticides and grass seeds are provided in the alphabetized table listing flow control settings If the product is not listed in the flow control settings table use the calibration guide to set the flow control The agitator spring located inside the hopper provides consistent material flow of pelletized materials and seed It is not designed to break up lumps of material or seed Break up any lumps as you fill the hopper After determining the correct setting number for your material move flow control lock to that position Move flow control handle to the lock position to open the flow control plate Directional Control Settings Normal Operation Uniform Spreading Fertilizers insecticides and grass seed each have different particle size and weight This can be referred to as particle density As the particles are impacted by the fan the distribution can be centered or slightly off center depending on particle density and forward vehicle speed MX34606 Adjustment can be made by moving the direction control handle to the right or left The directional decal located below the directional control plate handle will aid you in adjusting the spread pattern For most applications the handle should be placed close to the center position A described by the label
16. r concerns with the assembly installation or operation of this attachment see your local John Deere dealer or call John Deere Special Services at 1 866 218 8622 for assistance Warranty information on this John Deere attachment can be found in the warranty that came with your John Deere tractor or vehicle Safety Read the general safety operating precautions in your machine operator s manual for additional safety information Operate Safely e This attachment is intended for use in lawn care and home applications Do not tow behind a vehicle on a highway or in any high speed application Do not tow at speeds higher than maximum recommended towing speed e Towing speed should always be slow enough to maintain control Travel slowly over rough ground e Do not let children or an untrained person operate machine e Do not let anyone especially children ride on machine or attachment Riders are subject to injury such as being struck by foreign objects and being thrown off Riders may also obstruct the operator s view resulting in the machine being operated in an unsafe manner e Check machine brake action before you operate Adjust or service brakes as necessary e Keep all parts in good condition and properly installed Fix damage immediately Replace worn or broken parts Replace all worn or damaged safety and instruction decals e Do not modify machine or safety devices Unauthorized modifications to the machine or attachment
17. rn Calibration settings have been determined using a 3 MPH pace or 40 ft of travel in 9 seconds Calibration Guide for Flow Control Settings Ibs 1000 square feet Flow Control Setting 0 5 0 9 1 1 0 1 4 2 1 5 2 4 2 5 2 5 3 4 3 3 5 3 9 3 5 4 0 4 4 4 4 5 4 9 4 5 5 0 5 9 5 6 0 7 4 5 5 7 5 8 9 6 9 0 10 9 6 5 11 0 12 9 7 13 0 14 9 T5 15 0 17 9 8 18 0 20 9 9 21 0 24 5 10 Getting Quality Service John Deere Quality Continues with Quality Service John Deere provides a process to handle your questions or problems should they arise to ensure that product quality continues with quality parts and service support Follow the steps below to get answers to any questions you may have about your product 1 Refer to your attachment and machine operator manuals 2 In North America or Canada call John Deere Special Services at 1 866 218 8622 and provide product serial number if available and model number Getting Quality Service 11
18. tarter Fertilizer 20 27 5 Mixture C 5 9 4 5 Scotts Starter Fertilizer 20 27 5 4 5 5 Pennington Master Turf Shady Lawn Seed Mi 2 7 3 5 Scotts Turf Builder 28 3 8 ixture 10 7 Pennington Master Turf Sun and Shade Lawn 3 1 3 Scotts Turf Builder Lawn Fertilizer 29 3 4 Seed Mixture 2 7 3 5 Scotts Turf Builder with Summer Guard 5 5 5 Pennington Master Turf Sun and Shade Lawn 29 3 5 Scotts Turf Builder Plus Weed Control Seed Mixture F i 3 3 3 Scotts Winterizer 22 4 1 2 2 5 Real Kill Multi Purpose Lawn and Garden Insect Killer 4 6 4 5 Sevin Lawn Insect Granules 2 5 3 Real Kill Multi Purpose Lawn and Garden Insect 2 33 3 5 Sevin Lawn Insect Granules Killer 2 25 3 5 Sevin Lawn Insect Granules 10 7 Rebels Supreme Blend Grass Seed for Sun and Shade 3 4 Spectracide Grub Stop 5 5 5 Rebels Supreme Blend Grass Seed for Sun and 3 2 Spectracide Traizicide Insect Killer Granules Shade 3 6 3 5 Sta Green Lawn Fertilizer 29 2 5 10 7 Ringer Lawn Restore 10 2 6 2 3 Sta Green Lawn Weed Control 12 3 7 5 Sam s Choice Crabgrass Preventer 30 3 4 3 2 3 5 Sta Green 200 Plus Weed and Feed 28 3 3 8 1 6 Sam s Choice Crabgrass Preventer 30 3 4 3 6 3 5 Sta Green Starter Fertilizer 18 24 10 6 5 5 Sam s Choice Crabgrass Preventer 30 3 4 3 2 3 5 Sta Green Weed and Feed 28 2 4 5 4 5 Sam s Choice Crabgrass Preventer 30 3 4 10 7 Sun and Shade Grass Seed Mixture 3 3 Sam s Choice Insect Control Plus Fertilizer 28 4 6 5 5 5 Sun and Shade Grass Seed Mixture 3 2 3 5 Sam s C
Download Pdf Manuals
Related Search
Related Contents
2『私たちが知りたい化学物質の情報』 Technique de l`imprimerie à l`école, Composition, Impression Ableitermonitoring mit 3EX5 060 und 3EX5 062 User Manual (maintenance) Page 1 Page 2 目次 ー Samsung LE-32C350 32" Full HD Black デュオルーム所蔵図書一覧(PDF:870KB) AMD ATI Xpert 98 取扱説明書 Smeg LPD862 sink Copyright © All rights reserved.
Failed to retrieve file