Intel PCI-471LF User's Manual
Contents
1. VCC12 Manufacturing Default RI Page 2 8 PCI 471LF USER S MANUAL Chapter 2 Hardware Configuration 2 7 RS232 422 485 COM2 SELECTION JP8 RS 232 422 485 2 Selection This connector is used to set the COM2 function The jumper settings are as follows COM 2 Jumper Settings Jumper Function pin closed Illustrations 9 1 RS 232 OPEN OPEN OPEN RS 422 1 2 3 4 9 10 RS 485 1 2 5 6 7 8 Manufactory default RS 232 PCI 471LF USER S MANUAL Page 2 9 Chapter 2 Hardware Configuration 2 8 KEYBOARD OR PS 2 MOUSE CONNECTOR DIN Keyboard or PS 2 Mouse Connector DIN connector can support keyboard Y cable or PS 2 Mouse user may select the right device to used on Keyboard or PS 2 Mouse Selection The pin assignments are as follows ASSIGNMENT Keyboard KBDATA MSDATA DIN 2 9 KEYBOARD OR PS 2 MOUSE SELECTION JP4 Keyboard or PS 2 Mouse Selection For Y Cable user please set the jumper same as AT keyboard The jumper settings are as follows ede JUMPER SETTING pin closed ILLUSTRATION 3 5 2 6 KEYBOARD i 5 JP4 1 3 2 PS 2 MOUSE a E JP4 Manufactory default AT Keyboard Page 2 10 PCI A7ILF USER S MANUAL Chapter 2 Hardware C2. 2 2 IrDA Connector Leech per E p p fae CPU Fan Connector 2 2 System Fan Connector 2 Clear CMOS Data Selection CRT Connector 2 Hard Disk Drive Connector sse Floppy Disk Drive Connector een Printer Connector iac aae ORI Universal Serial Bus Connector LAN Connector lt sana ATX Power Connector SXVSB ConneGCtOE uei ese reor POE reprises AN AG Contents Contents 2 29 2 30 2 31 2 32 2 33 2 34 PCI Slot 3 3V Voltage Selection Inverter Connector 0 0 0022 Reset NMI Clear Watchdog Selection AT ATX Power Selection LVDS Connector eren enr erento NA LVDS Panel Voltage Selection CHAPTER 3 SOFTWARE UTILITIES 3 1 3 2 3 3 3 4 3 5 3 6 3 7 Introduction ie VGA Driver Utility dessus nas Ud edi e ERR HU EL TRUM Flash BIOS Update oer Here rni LAN Driver Utility Intel Chipset Software Installation Utility USB2 0 Software Installation Utility Watchdog Configuration CHAPTER 4 AWARD BIOS SETUP 4 1 4
3. MEMORY Supports up to 1GB DDR266 SDRAM One 200 pin DDR SO DIMM sockets on board CACHE Built in CPU REAL TIME CLOCK CALENDAR 256 byte battery backed CMOS RAM Hardware implementation to indicate century rollover e 8105 Phoenix AwardBIOS for plug amp play function Memory size with 4 MB with VGA BIOS e KEYBOARD MOUSE CONNECTOR Mini DIN connector selectable for Keyboard PS 2 Mouse or Y Cable One additional 5 pin External keyboard connector UNIVERSAL SERIAL BUS Universal Serial Bus Connector on board Supports up to two USB 2 0 ports BUS SUPPORT PCI Bus External EPCI Bus Compact Flash Bus PCI 471LF USER S MANUAL Page 1 3 Chapter 1 Introduction DISPLAY Built in Intel 852GM support CRT LVDS 18 bit IDE INTERFACE One IDE ports support up to four IDE devices Supports UDMA 33 66 100 FLOPPY DISK DRIVER INTERFACE Supports up to two Floppy Disk Drives 3 5 and 5 25 LAN INTERFACE Dual ports LAN 1 Intel 82562ET 10 100 Mbps Ethernet Supports Wake on LAN with ATX power SERIAL PORT Two high speed 16550 Compatible UARTs with Send Receive 16 Byte FIFOs COMI for RS232 COM2 for RS232 422 485 PARALLEL PORT One port supports SPP ECP EPP Function HARDWARE MONITORING FUNCTION Monitor Voltage CPU Temperature and Cooling Fan IRDA PORT One 5 pin Infrared connector Supports IrDA v1 0 SIR protocol LED INDICATOR
4. 9 VGA VGA DDC CLK PCI 471LF USER S MANUAL Page 2 15 Chapter 2 Hardware Configuration 2 22 HARD DISK DRIVE CONNECTOR IDE Hard Disk Drive Connector The pin assignments are as follows GND 5 ros PDD 8 SPDDIO 13 15 17 19 GND a NECK CE 21 ND 23 ND 25 ND 27 29 GND 31 33 35 GND Page 2 16 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 23 FLOPPY DISK DRIVE CONNECTOR FDDI Floppy Disk Drive Connector You can use a 34 pin daisy chain cable to connect two FDDs On one end of this cable is a 34 pin flat cable to attach the FDD on the board and the other side is attaches two FDDs The pin assignments are as follows Ld o0o00000 88600000000 1 2 ASSIGNMENT GND GND ee 5 GND HET 88 ND G GND GND G G ND ND GND GND GND ND I 1 3 5 7 3 5 7 9 1 3 5 7 9 1 3 1 1 1 1 2 2 2 2 2 3 3 iE 21 GND 23 _ 25 __27 _ ND ND PCI 471LF USER S MANUAL Page 2 17 Chapter 2 Hardware Configuration 2 24 PRINTER CONNECTOR PRNTI Printer Connector As to link the Printer to the card you need a cable to c
5. Place insert the Utility Disk into Floppy Disk Drive or CD ROM drive Under Windows 9X NT4 0 2000 XP system go to the directory where VGA driver is located Click Setup exe file for VGA driver installation Follow the instructions on the screen to complete the installation Once installation is completed shut down the system and restart in order for the changes to take effect amp Under the Windows 98 system after rebut computer there will have two error messages appear Can t find ikch8xx cat isb8xx cat just skip the messages they will not cause any effects 3 3 FLASH BIOS UPDATE 3 3 1 System BIOS Update Users of PCI 471LF can use the program Awdflash exe contained in the Utility Disk for system BIOS and VGA BIOS update 3 3 2 To update VGA BIOS for LCD Flat Panel Display As PCI 471LF user you have to update the VGA BIOS for your specific LCD flat panel you are going to use For doing this you need two files One is the Awdflash exe file and the other is the VGA BIOS for ATI Rage Mobility file for LCD panel display Both file must be provided by the vendor or manufacturer When you get these two files ready follow the following steps for updating your VGA BIOS 1 2 Install Awdflash exe from Utility Disk to Drive C Insert the VGA BIOS file you have obtained from the vendor Type the path to Awdflash exe and execute the VGA BIOS update with file H1Sbxxxx bin C UTIL AWDFLA
6. The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 AGP APERTURE SIZE This field determines the effective size of the Graphic Aperture used for a particular GMCH configuration It can be updated by the GMCH specific BIOS configuration sequence before the PCI standard bus enumeration sequence takes place If it is not updated then a default value will select an aperture of maximum size PCI 471LF USER S MANUAL Page 4 11 Chapter 4 Award BIOS Setup 4 6 INTEGRATED PERIPHERALS Choose INTEGRATED PERIPHERALS from the main setup menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter gt Onboard Device Press Enter Item Help Press Enter Menu Level gt gt SuperIO Device Watch Dog Timer Select Disabled Enter Select PU PD Value Fl0 Save ESC Exit Fl General Help ND Move F6 Fail Safe Defaults F7 Optimized Defaults F5 Previous Values Integrated Peripherals Setup Screen By moving the cursor to the desired selection and by pressing the lt F1 gt key the all options for the desired selection will be displayed for choice If bios setup menu item supports USB device boot it will cause Win9x detects the same storages twice when the system is rebooted and USB HDD will fail Note
7. 7 5 4 5 9 7 1 5 8 1 1 9 0 2 3 4 2 6 5 6 5 5 6 6 8 N Wan PCI 471LF USER S MANUAL Page 4 7 Chapter 4 Award BIOS Setup 4 4 THE ADVANCED BIOS FEATURES Choose the ADVANCED BIOS FEATURES in the main menu the screen shown as below Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU LI amp L2 Cache Enabled Quick Power On Self Test Enabled First Boot Device CDROM Menu Level Second Boot Device HDD 0 Boot Up Floppy Seek Enabled Allows you to choose Boot Up NumLock Status On the VIRUS warming Typematic Rate Setting Disabled feature for IDE Hard x Typematic Rate Chars Sec 6 Disk boot sector x Typematic Delay Msec 250 protection If this Security Option Setup function is enabled and OS Select For DRAM gt 64MB Non OS2 someone attempt to write data into this area BIOS will show a warning message on screen and alarm beep fi Move Enter Select PU PD Value Fl0 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults BIOS Features Setup Screen The BIOS FEATURES SETUP allow you to configure your system for basic operation The user can select the system s default speed boot up sequence keyboard operation shadowing and security A brief introduction of each setting is given below CPU L1 amp L2 CACHE This item allows you to enable L1 amp L2 cache QUICK POWER O
8. Former Sts Page 4 16 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup 4 7 POWER MANAGEMENT SETUP Choose POWER MANAGEMENT SETUP option on the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled Item Help Power Management User Define Video Off Method DPMS Video Off In Suspend Yes MODEM Use IRQ 3 Suspend Mode Disabled Power Supply Type ATX Me Soft Off by PWR BTTN Instant Off Wake Up by PCI card Enabled Wake Up On LAN Enabled Resume by Alarm Disabled x Date of Month Alarm 0 x Time hh mm ss Alarm 0 0 0 Reload Global Timer Events Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD COM LPT Port Disabled fi Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Power Management Setup Screen The Power Management Setup allows the user to configure the system to the most effectively save energy while operating in a manner consistent with your own style of computer use ACPI SUSPEND TYPE This item allows the user to set the ACPI suspend type to be used POWER MANAGEMENT This item allows you to select the Power Management mode PCI 471LF USER S MANUAL Page 4 17 Chapter 4 Award BIOS Setu VIDEO OFF OPTION When e
9. HDD LED Power LED DMA CONTROLLER 82C37 x 2 DMA CHANNELS 7 Page 1 4 PCI 471LF USER S MANUAL Chapter 1 Introduction INTERRUPT CONTROLLERS 82C59 x 2 INTERRUPT LEVELS 15 OPERATING TEMPERATURE 0 to 60 C 32 F to 140 F INPUT POWER REQUIREMENT ATX power 5V 12V AT power BOARD DIMENSION 185mm x 122mm 7 28 x 4 8 BOARD NET WEIGHT 230 grams 0 51 Ib 1 3 SAFETY PRECAUTIONS Follow the messages below to avoid your systems from damage 1 Avoid your system from static electricity on all occasions 2 Prevent electric shock Don t touch any components of this card when the card is power on Always disconnect power when the system is not in use Disconnect power when you change any hardware devices For instance when you connect a jumper or install any cards a surge of power may damage the electronic components or the whole system PCI 471LF USER S MANUAL Page 1 5 CHAPTER HARDWARE 2 CONFIGURATION QUICK START Helpful information describes the jumper amp connector settings and component locations Section includes Jumper amp Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector s Pin Assignments Page 2 1 Chapter 2 Hardware Configuration 2 1 JUMPER amp CONNECTOR QUICK REFERENCE TABLE COM Port Connector 2 COMI Port RI Voltage
10. PCI Bus Master PCI 471LF USER S MANUAL Page A 3 Appendix A Expansion Bus COMPACT FLASH CARD CONNECTOR PIN ASSIGNMENT The pin assignments of Compact Flash Card connector are stated below 10 n 12 13 14 15 16 17 18 19 20 4 PCI 471LFUSER 5 MANUAL TECHNICAL SUMMARY Page B 1 Appendix B Technical Summa BLOCK DIAGRAM 855GM GMCH VR LVDS gt BACKLIGHT CONNECTOR 165 330 MPIKELS 732UFCBGA 852GM DAC CRT MONTARA DDR266 333 HUB LINK INTERFACE 1 5 66MHZ X4 PRIMARY IDE CF CARD 70 ATATUA ICH4 ICH4 M 421 8280108 gt lt RIDA gt USB 1 1 2 0 4MB FLASH BIOS LPC SIO W83627HF PARALLEL LAN2 82540EM LOW PIN COUNTER LAN1 82562EM LNNOO FLOOPY KB MS COM2 Page B 2 PCI 471LF USER S MANUAL Appendix Technical Summary INTERRUPT MAP ASSIGNMENT ___0 ____ SystemTIMER 0 0 0 6 Floppy ___5 ___ 0 9 ____ Available PCI 471LF USER S MANUAL Page B 3 Appendix B Technical Summary RTC amp CMOS RAM MAP CODE ASSIGNMENT 01 2 Minutes 03 Minutes alarm 0 Hours Hours alarm Day of week 05 07 Day of month 0 E Month 2 13 14 15 16 17 18 30 31 32 33 34 3F 40 7f 0A OC OE OF 10 Page 4 PCI 471LF USER S MANUAL Appendix Technical Summary TIMER a
11. Selection JP6 2 Port RI Voltage Selection _ JP7 RS232 422 485 COM2 Selection 1 8 Keyboard Mouse Connector DINI Keyboard Mouse Selection JP4 Reset Connector JPANEL 9 11 Hard Disk Drive LED Connector JPANEL 5 7 ATX Power Button JPANEL 10 12 External Speaker Connector JPANEL 1 3 Power LED Connector JPANEL 4 6 8 KeyLock Connector masene neradan eid JPANEL 13 14 Connector teet EA E te JPANEL 17 18 19 20 Clear CMOS Data Selection JP10 CPU Fan Connector 2 2 21 0 0000 JCFANI System Fan Connector 0 JSFANI VGA Connector VGA Hard Disk Drive Connector _ __ Floppy Disk Drive Connector FDDI Printer Connector PRNTI Universal Serial Bus Connector USBI LAN Connector LANI ATX Power Connector 2 22 0 PWI SVSB ConnectOR REFS TA JP3 PCI Slot 3 3V Voltage JP9 Inverter Connector 14 Reset NMI Clear Watchdog Selection JP2 AT ATX Power Selection JP1 JP2 1 2 JP15 LVDS COnnectOE MSS CNT3 LVDS Voltage Selection JP12 Pa
12. adapter includes high resolution monochrome adapters HALT ON This category allows user to choose whether the computer will stop if an error is detected during power up Available options are All errors No errors All But keyboard All But Diskette and But Disk Key BASE MEMORY Displays the amount of conventional memory detected during boot up EXTENDED MEMORY Displays the amount of extended memory detected during boot up TOTAL MEMORY Displays the total memory available in the system Page 4 6 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup HARD DISK ATTRIBUTES Type Cylinders Heads V P comp LZone Sect Capacity 306 4 128 305 10 615 300 615 20 615 300 615 30 940 512 940 940 512 940 615 65535 615 642 256 511 733 65535 733 900 65535 901 820 65535 820 855 65535 855 855 65535 855 306 128 319 733 65535 733 000 0000 000 612 0000 663 977 300 977 977 65535 977 1024 512 1023 733 300 732 733 300 732 733 300 733 306 0000 336 977 65535 976 1024 65535 1023 1224 65535 1223 1224 65535 1223 1224 65535 1223 1024 65535 1023 1024 65535 1023 918 65535 1023 925 65535 926 65535 1023 65535 1023 65535 1023 65535 1023 65535 1023 65535 1023 65535 1023 65535 820 65535 1023 65535 1023 65535 852 65535 852 65335 AUTO Award Hard Disk Type Table gt Un N NNN NNNNNNNNNNNNNNNNNNNNNONNNNNNNNNNNNANU 3 5 8 7 0 4 5 7 7 5
13. assigned to PCI Device IRQ 10 assigned to PCI Device Legacy ISA for devices IRQ 11 assigned to PCI Device compliant with the IRQ 12 assigned to PCI Device original PC AT bus IRQ 14 assigned to PCI Device specification PCI ISA IRQ 15 assigned to PCI Device PnP for devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture fl Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help 5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 13 IRQ n Assigned to You may assign each system interrupt a type depending on the type of device using the interrupt PCI 471LF USER S MANUAL Page 4 21 Chapter 4 Award BIOS Setup 4 9 PC HEALTH STATUS Choose PC HEALTH STATUS the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility PC Health Status Current Warning Temperature Disabled Item Help Current CPU Temperature 48 C 118 F Current SYSTEM Fan Speed 0 RPM Menu Level Current CPU Fan Speed 4856 RPM Vcore 1 31V Vecp 1 02V 33V 3 29V 5V 4 81V 12V 11 61V 12V 12 28V 5 5 90V 3 13V fi Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PC Health Status Setup Screen The PC Health St
14. be denied if the correct password is not entered at the prompt Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt amp To disable security select PASSWORD SETTING at Main Menu and then you will be asked to enter password Do not type anything and just press lt Enter gt it will disable security Once the security is disabled the system will boot and you can enter Setup freely PCI 471LF USER S MANUAL Page 4 9 Chapter 4 Award BIOS Setup OS SELECT FOR DRAM gt 64MB Select the operating system that is running with greater than 64MB or RAM on the system You may choose OS2 or Non OS2 4 5 ADVANCED CHIPSET FEATURES Choose the ADVANCED CHIPSET FEATURES from the main menu the screen shown as below Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Data Integrity Mode Non ECC Item Help System BIOS Cacheable Enabled Video BIOS Cacheable Disabled Memory Hole At 15 16 Disabled Menu Level Delayed Transaction Enabled AGP Aperture Size MB 64 On Chip VGA Setting On Chip VGA Enabled On Chip Frame Buffer Size 32MB Boot Display CRT LFP Panel Type 800 x 600 18bits PCI SERRZ NMI Disabled Ne Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Chipset Features Setup Screen This pa
15. connector the PCI BUS edge connector is also divided into two sets one consists of 98 pin the other consists of 22 pin The pin assignments are as follows B1 B49 B52 B62 nnnnnnnnnnnnnnnnnnnnnnnnnnnaununnnnnnnnnnnnnnnnnnnn 00000000000 jajajajajajajajagajnjajujajnjajajajajajajajajajupajajajugajngajujujujajnjajujajnjajajgajajujujujngangggagnjngajajajujujujuja Al 49 52 62 TCK a2 GND I NTD 12 14 1 17 _____ 18 Xx 2 GND DO SV SV ND 3 3V D23 D21 D19 EE 00 1 m w a Q 2 w 23 27 24 05 2 2 2 GND 2 30 9__ 30 B62 5V AG2 gt gt ojo 5 ala Q 2 N N w Page A 2 PCI 471LFUSER 5 MANUAL Appendix A Expansion Bus CONNECTOR You will find a EPCI connector in our PCI 471LF The pin assignments are as follows B30 B1 000000000000000000000000000000 A30 1 ASSIGNMENT GND GND ADO AD2 AD3 AD4 AD6 AD7 ADS ADIO ADI2 10 An A12 A13 AD20 AD22 AIS 16 24 AD26 18 28 19 AD30 A20 PIRQ B PAR 21_ PPCLK 22 ID SEL A24 CBE 2 PGNT 4 SERR PIRO A STOP 29__ DEVSELH GND GND The expansion connector of this Card is designed based on
16. likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1 1 1 2 1 3 About This Manual eene System Specification Safety Precautions eh CHAPTER 2 HARDWARE CONFIGURATION 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 2 10 2 11 2 12 2 13 2 14 2 15 2 16 2 17 2 18 2 19 2 20 2 21 2 22 2 23 2 24 2 25 2 26 2 27 2 28 Jumper amp Connector Quick Reference Table Component Locations How to Set the Jumpers esee Port Connector COMI RI amp Voltage Selection 2 RI amp Voltage Selection 5232 422 485 2 Selection Keyboard PS 2 Mouse Connector _ Keyboard or PS 2 Mouse Selection External Keyboard Connector sss Reset Connector inr Hard Disk Drive LED Connector ATX PowerButton External Speaker Connector Power Led Connector eee KeyLock Connector
17. this cause just happen under Win9x the phenomenon is a limitation Page 4 12 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup VIA ONCHIP IDE DEVICE The options for these items are found in its sub menu By pressing the lt gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility VIA OnChip IDE Device OnChip Primary PCI IDE Enabled Item Help IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Primary Master UDMA Auto Menu Level gt IDE Primary Slave UDMA Auto OnChip Secondary PCI IDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto IDE HDD Block Mode Enabled Tl Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 OnChip Primary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately 2 Primary Master Slave PIO Secondary Master Slave PIO The four IDE PIO fields allow you to set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the be
18. 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 4 10 4 11 4 12 4 13 4 14 4 15 IMtCOdUCHON 21 5 erbe oe Entermpg Set p tede bete Sverre eed The Standard CMOS Features The Advanced BIOS Features 22 2 Advanced Chipset Features sese Integrated Peripherals Power Management Setup PNP PCI Configuration PC Health Status Frequency Control Load Fail Safe Defaults Load Optimized Defaults Password Setting Save amp Exit Setup sese Exit Without Saving 2 21 2 3 8 Contents APPENDIX EXPANSION BUS PCI Bus Pin Assignment 2 A 2 EPCI Connector np devant pr ETE ee Dee A 3 Compact Flash Card Connector Pin Assignment A 4 APPENDIX B TECHNICAL SUMMARY Block erem erret B 2 Interrupt Leere Maladie Deben B 3 amp CMOS 0 2 2 20040040022 B 4 Timer amp DMA Channels Map eee B 5 amp Memory Map eee eee B 6 INTRODUCTION Page 1 1 Chapter 1 Introduction 1 1 ABOUT THIS MANUAL Thank you for purchasing our PCI 471LF Intel Celeron M Half Size Card enhanced with VGA LAN which is fully PC AT compatible PCI A71LF provides faster processi
19. 7 Onboard FDC Controller Select Enabled if the system has a floppy disk controller FDC installed on the system board and you wish to use it If you install and in FDC or the system has no floppy drive select Disabled Onboard Serial Port 1 2 Select an address and corresponding interrupt for the first and second serial ports UART Mode Select This item allows you to select UART mode RxD TxD Active This item allows you to determine the active of RxD TxD IR Transmission Delay This item allows you to enable disable IR transmission delay UR2 Duplex Mode This item allows you to select the IR half full duplex function Use IR Pins PCI 471LF USER S MANUAL Page 4 15 Chapter 4 Award BIOS Setup 10 11 12 This item allows you to select IR transmission routes one is RxD2m TxD2 COM Port and the other is IR Rx2Tx2 Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O address Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal Compatible or SPP unless you are certain your hardware and software both support one of the other available modes EPP Mode Select Select EPP port type 1 7 or 1 9 ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode PWRON After PWR Fail This item allows you to select if you want to power on the system after power failure The choice Off On
20. ECTION JP12 LVDS Panel Voltage Selection The selections are as follows SELECTION JUMPER SETTING LVDS VCC5 PCI 471LF USER S MANUAL JUMPER ILLUSTRATION Page 2 25 SOFTWARE 3 UTILITIES Page 3 1 Chapter 3 Software Configuration 3 1 INTRODUCTION Enclosed with our PCI 471LF package is our driver utility which may comes in a form of a CD ROM disc or floppy diskettes For CD ROM disc user you will only need some of the files contained in the CD ROM disc please kindly refer to the following chart Assume that CD ROM drive is D For VGA driver installation D Driver FLASH For BIOS update utility D Driver LAN For LAN Driver installation D Driver UTILITY Intel Chipset Software Installation Utility For Win 98SE ME 2000 XP D Driver USB 2 0 USB 2 0 Software Installation Utility For Win 98SE 2000 ME XP amp User should remember to install the Utility right after the OS fully installed 3 2 VGA DRIVER UTILITY The VGA interface embedded with our PCI 471LF can support a wide range of display You can display CRT LVDS simultaneously with the same mode VGA Disc 7 2 1 Win 9X program 2 Win NT4 0 program 3 Win 2000 program 4 Win XP program Page 3 2 PCI 471LF USER S MANUAL Chapter 3 Software Configuration 3 2 1 Installation of VGA Driver To install the VGA Driver simply follow the following steps 1
21. ECTION JP2 Reset NMI Clear Watchdog Selection The selections are as follows SETTING JU on KAKI CLEAR WATCHDOG Manufacturing Default is set as open User may select to use the Reset or NMI watchdog NMI also known Non Maskable Interrupt is used for serious conditions that demand the processor s immediate attention it cannot be ignored by the system unless it is shut off specifically To clear NMI command user should short the Clear Watchdog pin via push button Page 2 22 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 32 AT ATX POWER SELECTION JP1 JP2 1 2 JP15 AT ATX Power Selection The selections are as follows JUMPER SETTING Tey ILLUSTRATION Ji Je2 20 2 2 qms oe Manufacturing Default is set as PCI 471LF USER S MANUAL Page 2 23 Chapter 2 Hardware Configuration 2 33 LVDS CONNECTOR CNT3 LVDS Connector The pin assignments are as follows 10 2 000000000000000 B CNT3 ASSIGNMENT LCD_VCC ZCM GND 6 Z2P 8 GND ZIM 10 Z3P ZOP GND YCM Y2P GND YIM YOP Y3P LCD_VCC 30 LCD_VCC Page 2 24 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 34 LVDS PANEL VOLTAGE SEL
22. Mov al 08h Out dx al Dec dx Set second as counting unit Mov al Of5h Out dx al Inc dx In al dx And al not 08h Out dx al Dec dx Set timeout interval as 30seconds and start counting Mov al Of6h Out dx al Inc dx Mov al 30 Out dx al Dec dx Exit the extended function mode Mov al Oaah Out dx al PCI 471LF USER S MANUAL Page 3 9 CHAPTER AWARD 4 BIOS SETUP This chapter shows how to set up the Award BIOS Section includes Introduction Entering Setup The Standard CMOS Features The Advanced BIOS Features The Advanced Chipset Features Integrated Peripherals Power Management Setup PNP PCI Configuration PC Health Status Frequency Control Load Fail Safe Defaults Load Optimized Defaults Password Setting Save and Exit Setup Exit Without Saving Page 4 1 Chapter 4 Award BIOS Setup 4 1 INTRODUCTION This chapter will show you the function of the BIOS in managing the features of your system The PCI 471LF Celeron M Half Size CPU Card is equipped with the BIOS for system chipset from Award Software Inc This page briefly explains the function of the BIOS in managing the special features of your system The following pages describe how to use the BIOS for system chipset Setup menu Your application programs such as word processing spreadsheets and games rely on an operating system such as DOS or OS 2 to manage such things as keyb
23. N SELF TEST This item allows you to speed up Power On Self Test POST after power up the computer When enabled the BIOS will shorten or skip some check items during POST Page 4 8 PCI 471LF USER S MANUAL Chapter 4 BIOS Setup FIRST SECOND BOOT DEVICE The BIOS attempt to load the operating system from the devices in the sequence selected in these items BOOT UP FLOPPY SEEK You may enable disable this item to define whether the system will look for a floppy disk drive to boot at power on or proceed directly to the hard disk drive BOOT UP NUMLOCK STATUS Select power on state for NumLock TYPEMATIC RATE SETTING Enable this item if you wish to be able to configure the characteristics of your keyboard Typematic refers to the way in which characters are entered repeatedly if a key is held down For example if you press and hold down the A key the letter a will repeatedly appear on your screen on your screen until you release the key When enabled the typematic rate and typematic delay can be selected TYPEMATIC RATE CHARS SEC This item sets the number of times a second to repeat a key stroke when you hold the key down TYPEMATIC DELAY MSEC The item sets the delay time after the key is held down before it begins to repeat the keystroke SECURITY OPTION This category allows you to limit access to the system and Setup or just to Setup System The system will not boot and access to Setup will
24. SH gt AWDFLASH H20bxxxx bin The screen will display as the table fount on the next page PCI 471LF USER S MANUAL Page 3 3 Chapter 3 Software Configuration FLASH MEMORY WRITER v7 XX C Award Software 2001 AII Rights Reserved Flash Type SST 49LF004A 3 3V File Name to Program H20bxxxx bin Checksum Error Message Do You Want To Save BIOS Y N If you want to save up the original BIOS enter and press lt Enter gt If you choose N the following table will appear on screen FLASH MEMORY WRITER v7 XX C Award Software 2001 All Rights Reserved Flash Type SST 49LF004A 3 3 File Name to Program H20bxxxx bin Checksum Error Message Are You Sure To Program Y N Select and the BIOS will be renewed When you are refreshing the BIOS do not turn off or reset the system or you will damage the BIOS After you have completed all the programming the screen displays the table below Page 3 4 PCI 471LF USER S MANUAL Chapter 3 Software Configuration FLASH MEMORY WRITER v7 XX C Award Software 2001 All Rights Reserved Flash Type SST 49LF004A 3 3 File Name to Program H20bxxxx bin Checksum XXXXX Reset System or Power off to accomplish update process Fl Reset F10 Exit Please reset or power off the system and then the Flash BIOS is fully implemented 3 4 LAN DRIVER UTILITY 3 4 1 Introduction PCI 471LF is enhanced with LAN function that ca
25. USER S MANUAL PCI 471LF M2 PCI 47 1LF Celeron Half Size CPU Card With VGN LAN Copyright Notice PCI 471LF Celeron M Hal Size CPU Card With VGA LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system The information contained in this document is subject to change without any notice This manual is copyrighted in March 2006 You may not reproduce or transmit in any form or by any means electronic or mechanical including photocopying and recording ACKNOWLEDGEMENTS All trademarks and registered trademarks mentioned herein are the property of their respective owners CE NOTICE This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is
26. ally greater than the size of a formatted disk given by a disk checking program e Cyls number of cylinders e Head number of heads e write precompensation cylinders e Landz landing zone e Sector number of sectors e Mode Auto Normal Large or LBA Auto The BIOS automatically determines the optimal mode Normal Maximum number of cylinders heads sectors supported are 1024 16 and 63 Large For drives that do not support LBA and have more than 1024 cylinders PCI 471LF USER S MANUAL Page 4 5 Chapter 4 Award BIOS Setup Logical Block Addressing During drive accesses the IDE controller transforms the data address described by sector head and cylinder number into a physical block address significantly improving data transfer rates For drives greater than 1024 cylinders DRIVE A AND DRIVE B Select the type of floppy disk drive installed in your system The available options are 360KB 5 25in 1 2KB 5 25in 720KB 3 5 1 44MB 3 5in 2 88MB 3 5in and None VIDEO This category selects the type of video adapter used for the primary system monitor Although secondary monitors are supported you do not have to select the type in Setup Available Options are as follows Enhanced Graphics Adapter Video Graphics Array For EGA VGA SEGA SVGA or PGA monitor adapters Color Graphics Adapter power up in 40 column mode Color Graphics Adapter power up in 80 column mode Monochrome
27. atus Setup allows you to select whether to choose between monitoring or to ignore the hardware monitoring function of your system CURRENT WARNING TEMPERATURE Select the combination of lower and upper limits for the CPU temperature If the CPU temperature extends beyond either limit any warning mechanism programmed into your system will be activated CURRENT CPU TEMPERATURE This item shows you the current CPU temperature CURRENT SYSTEM FAN SPEED This item shows you the current System FAN speed CURRENT CPU FAN SPEED This item shows you the current CPUFAN speed Page 4 22 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup VCORE This item shows you the current system voltage 3 3V 5V 12 12V 5V Show you the voltage of 3 3V 5V 12V 12V SV 4 10 FREQUENCY CONTROL Choose FREQUENCY CONTROL from the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility Frequency Control Auto Detect PCI Clk Enabled Spread Spectrum Enabled Item Help Menu Level fi Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Frequency Control Setup Screen This setup menu allows you to specify your settings for frequency control AUTO DETECT PCI CLK This item allows you to enable or disable auto detect PCI Clock SPREAD SPECTRUM When the system clo
28. ck generator pulses the extreme values of the pulse generate excess EMI Enabling pulse spectrum spread modulation changes the extreme values from spikes to flat curves thus reducing EMI This benefit may in some cases be outweighed by problems with timing critical devices such as a clock sensitive SCSI device PCI 471LF USER S MANUAL Page 4 23 Chapter 4 Award BIOS Setup 4 11 LOAD FAIL SAFE DEFAULTS By pressing the lt ENTER gt key on this item you get a confirmation dialog box with a message similar to the following Load Fail Safe Defaults Y N To use the BIOS default values change the prompt to Y and press the lt Enter gt key CMOS is loaded automatically when you power up the system 4 12 LOAD OPTIMIZED DEFAULTS When you press lt Enter gt on this category you get a confirmation dialog box with a message similar to the following Load Optimized Defaults Y N Pressing Y loads the default values that are factory setting for optimal performance system operations Page 4 24 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup 4 13 PASSWORD SETTING User is allowed to set either supervisor or user password or both of them The difference is that the supervisor password can enter and change the options of the setup menus while the user password can enter only but do not have the authority to change the options of the setup menus TO SET A PASSWORD When you select this function the fol
29. es Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Managemen Save to CMOS and EXIT Y N Y gt PnP PCI Configura gt PC Health Status Esc Quit Ne Select Item F10 Save amp Exit Setup Save Data to CMOS When you confirm that you wish to save the settings your system will be automatically restarted and the changes you have made will be implemented You may always call up the setup program at any time to adjust any of the individual items by pressing the Del key during boot up Page 4 26 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup 4 15 EXIT WITHOUT SAVING If you wish to cancel any changes you have made you may select the EXIT WITHOUT SAVING and the original setting stored in the CMOS will be retained The screen will be shown as below Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Managemen Quit Without Saving Y N N gt PnP PCI Configura gt PC Health Status Esc Quit Ne Select Item F10 Save amp Exit Setup Abandon all Datas PCI 471LF USER S MANUAL Page 4 27 EXPANSION BUS Page A 1 Appendix A Expansion Bus PCI BUS PIN ASSIGNMENT Like ISA BUS
30. es how to configure PCI bus system PCI also known as Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers technical items which is strongly recommended for experienced users only RESET CONFIGURATION DATA Normally you leave this field Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system configuration has caused such a serious conflict that the operating system cannot boot Page 4 20 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup RESOURCE CONTROLLED BY The Award Plug and Play Bios can automatically configure all of the booth and Plug and Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 By choosing manual you are allowed to configure the Resources and DMA Resources IRQ RESOURCES The options for these items are found in its sub menu By pressing the lt gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility IRQ Resources IRQ 3 assigned to PCI Device Item Hel IRQ 4 assigned to PCI Device tem blerp 5 assigned to PCI Device IRQ 7 assigned to PCI Device Menu IRQ 9
31. ge 2 2 PCI 471LF USER S MANUAL Chapter 2 Hardware Configuration 2 2 COMPONENT LOCATIONS COM1 USB1 JSFAN 1 Bets INTEL ICH4 Celeron M S JP9 B30 EPCI 1 JPANEL1 A30 PCI 471LF Connector Jumper and Component locations PCI 471LF USER S MANUAL Page 2 3 Chapter 2 Hardware Configuration 2 3 HOW TO SET THE JUMPERS You can configure your board by setting jumpers Jumper is consists of two or three metal pins with a plastic base mounted on the card and by using a small plastic cap Also known as the jumper cap with a metal contact inside you are able to connect the pins So you can set up your hardware configuration by open or close pins The jumper can be combined into sets that called jumper blocks When the jumpers are all in the block you have to put them together to set up the hardware configuration The figure below shows how this looks like JUMPERS AND CAPS n AJAI AJAJAJ mim aim CA 2 Pin Jumper 3 Pin Jumper Jumper Block Jumper Cap If a jumper has three pins for examples labelled PIN1 PIN2 and PIN3 You can connect PIN1 amp PIN2 to create one setting and shorting You can either connect PIN2 amp PIN3 to create another setting The same jumper diagrams are applied all through this manual The figure below shows what the manual diagrams look and what they represent Page 2 4 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configurati
32. lowing message will appear at the center of the screen to assist you in creating a password Enter Password Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press the lt Enter gt key You may also press lt Esc gt to abort the selection and not enter a password A User should bear in mind that when a password is set you will be asked to enter the password everything you enter CMOS setup Menu TO DISABLE THE PASSWORD To disable the password select this function do not enter any key when you are prompt to enter a password and press the lt Enter gt key and a message will appear at the center of the screen PASSWORD DISABLED Press any key to continue Press the lt Enter gt key again and the password will be disabled Once the password is disabled you can enter Setup freely PCI 471LF USER S MANUAL Page 4 25 Chapter 4 Award BIOS Setup 4 14 SAVE amp EXIT SETUP After you have completed adjusting all the settings as required you must remember to save these setting into the CMOS RAM To save the settings select SAVE amp EXIT SETUP and press lt Enter gt a display will be shown as follows Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Control gt Advanced BIOS Featur
33. lt Month gt lt Date gt and lt Year gt Ranges for each value are in the CMOS Setup Screen and the week day will skip automatically Time lt Hour gt lt Minute gt and lt Second gt Use 24 hour clock format i e for PM numbers add 12 to the hour For example 4 30 P M You should enter the time as 16 30 00 Page 4 4 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup IDE Primary Master Slave IDE Secondary Master Slave The BIOS can automatically detect the specifications and optimal operating mode of almost all IDE hard drives When you select type AUTO for a hard drive the BIOS detect its specifications during POST every time system boots If you do not want to select drive type AUTO other methods of selecting drive type are available 1 Match the specifications of your installed IDE hard drive s with the preprogrammed values for hard drive types through 45 2 Select USER and enter values into each drive parameter field 3 Use the IDE HDD AUTO DETECTION function in Setup Here is a brief explanation of drive specifications Type The BIOS contains a table of pre defined drive types Each defined drive type has a specified number of cylinders number of heads write precompensation factor landing zone and number of sectors Drives whose specifications do not accommodate any predefine type are classified as type USER e Size Disk drive capacity approximate Note that this size is usu
34. mp DMA CHANNELS MAP Timer Channel Map Timer Channel System timer interrupt DRAM Refresh request Speaker tone generator DMA Channel Map ___0 Available Pf Available 0 04 PCI 471LF USER S MANUAL Page B 5 Appendix Technical Summary amp MEMORY Memory MEMORY MAP ASSIGNMENT 0000000 009 System memory used by DOS and application CGA MONOCHROME adapter RAM buffer 00E0000 00EFFFF Reserved for PCI device ROM 00F0000 00FFFFF System BIOS ROM 0100000 FFFFFFF MAP 000 01F 020 021 022 023 040 05F 060 06F 070 07F 080 09F 0 1F0 1F8 278 27F 2B0 2DF 2F8 2FF 360 36F 378 37F 3B0 3BF 3C0 3CF 3D0 3DF 3F0 3F7 3F8 3FF DMA register Interrupt controller Slave controller Slave Hard Disk controller Parallel port 2 Graphics adapter controller Serial port Net work ports Parallel port 1 2 Monochrome amp Printer adapter EGA adapter CGA adapter Floppy disk controller Serial port 1 Page B 6 PCI 471LF USER S MANUAL
35. n support various network adapters Installation programs for LAN drivers are listed as follows LAN Disc 9 1 Win 98 2000 XP program 2 Linux program For more details on Installation procedure please refer to Readme txt file found on LAN DRIVER UTILITY PCI 471LF USER S MANUAL Page 3 5 Chapter 3 Software Configuration 3 5 INTEL amp CHIPSET SOFTWARE INSTALLATION UTILITY 3 5 1 Introduction The Intel amp Chipset Software Installation Utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured This is needed for the proper functioning of the following features Core PCI and ISAPNP Services AGP Support IDE ATA33 ATA66 ATA100 Storage Support USB Support Identification of Intel Chipset Components in Device Manager 3 5 2 Installation of Utility for Windows 98SE ME 2000 XP The Utility Pack is to be installed only for Windows 98SE Windows ME Windows 2000 and XP program It should be installed right after the OS installation kindly follow the following steps 1 2 45 Page 3 6 Place insert the Utility Disk into Floppy Disk Drive A B or CD ROM drive Under Windows 98SE ME 2000 XP system go to the directory where Utility Disc is located Click Setup exe file for utility installation Follow the instructions on the screen to complete the installation Once installation is completed shut down the system and restar
36. nabled this feature allows the VGA adapter to operate in a power saving mode Always On Monitor will remain on during power saving modes Suspend gt Off Monitor blanked when the systems enters the Suspend mode Susp Stby gt Off Monitor blanked when the system enters either Suspend or Standby modes All Modes gt Off Monitor blanked when the system enters any power saving mode VIDEO OFF METHOD This determines the manner in which the monitor is blanked V H SYNC Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Select this option if your monitor supports the Display Power Management Signalling DPMS standard of the Video Electronics Standards to select video power management values MODEM USE IRQ This item enable you to name the interrupt request IRQ line assigned to the modem if any on your system Activity of the selected IRQ always awakens the system SUSPEND MODE When enabled and after the set time of system inactivity all devices except the CPU will be shut off SOFT OFF BY PWR BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The choices are Delay 4 Sec and Instant Off WAKE UP BY PCI CARD An input signal from PME on the PCI card awakens the sy
37. nfiguration 2 16 KEYLOCK CONNECTOR JPAENL 13 14 Keylock Connector The pin assignment is as follows ASSIGNMENT KEYLOCK 2 17 IRDA CONNECTOR JPANEL 17 18 19 20 IrDA Infrared Connector The pin assignments are as follows 2 18 CPU FAN CONNECTOR JCFANI CPU Fan connector The pin assignment is as follows PCI 471LF USER S MANUAL KEYLOCK 2 20 1 19 JPANEL IR 2 20 1 19 JPANEL JCFAN 1 Page 2 13 Chapter 2 Hardware Configuration 2 19 SYSTEM FAN CONNECTOR JSFANI System Fan connector The pin assignment is as follows ASSIGNMENT JSFAN1 2 20 CLEAR CMOS DATA SELECTION JP10 Clear CMOS Data Selection The selections are as follows JUMPER SETTING JUMPER FUNCTION pin closed ILLUSTRATION 1 1 Clear CMOS 2 3 1 JP10 JP10 Manufacturing Default is set as Normal Note To clear CMOS data user must power off the computer and set the jumper to Clear CMOS as illustrated above After five to six seconds set the jumper back to Normal and power on the computer Page 2 14 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 21 VGA CONNECTOR VGA CRT Connector The pin assignments are as follows 1 00000 000005
38. ng speed greater expandability and can handle more task than before This manual is designed to assist you how to install and set up the system It contains four chapters The user can apply this manual for configuration according to the following chapters Chapter 1 Introduction This chapter introduces you to the background of this manual and the specification for this system Final part of this chapter will indicate you how to avoid damaging this Embedded Card Chapter 2 Hardware Configuration This chapter outlines the component location and their functions In the end of this chapter you will learn how to set jumper and how to configure this card to meet your own needs Chapter 3 Software Utilities This chapter contains helpful information for proper installations of the VGA utility LAN utility sound utility and BIOS update It also describes the Watchdog timer configuration Chapter 4 Award BIOS Setup This chapter indicates you how to set up the BIOS configurations Appendix A Expansion Bus This Appendix introduces you the expansion bus for PCI Bus and EPCI Bus Appendix B Technical Summary This section gives you the information about the Technical maps Page 1 2 PCI 471LF USER S MANUAL Chapter 1 Introduction 1 2 SYSTEM SPECIFICATION CPU Intel Celeron M processor ULV Celeron M 600MHz without L2 cache System bus frequency at 400MHz Auto detect voltage regulator SYSTEM CHIPSET Intel 852GM chipset
39. oard monitor disk drives and memory The operating system relies on the BIOS Basic Input and Output system a program stored on a ROM Read only Memory chip to initialize and configure your computer s hardware As the interface between the hardware and the operating system the BIOS enables you to make basic changes to your system s hardware without having to write a new operating system The following diagram illustrates the interlocking relationships between the system hardware BIOS operating system and application program Application Program Operation System BIOS System Hardware Page 4 2 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup 4 2 ENTERING SETUP When the system is powered on the BIOS will enter the Power On Self Test POST routines and the following message will appear on the lower screen PRESS lt DEL gt TO ENTER SETUP ESC TO SKIP MEMORY TEST As long as this message is present on the screen you may press the lt Del gt key the one that shares the decimal point at the bottom of the number keypad to access the Setup program In a moment the main menu of the Award SETUP program will appear on the screen Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Frequency Control gt Advanced BIOS Features Load Fail Safe Defaults gt Advanced Chipset Features Load Optimized Defaults gt Integrated Peripherals Set Supervisor Password gt Power Management Setup Set Use
40. on JUMPER DIAGRAMS 2 looks like this 2 pin Jumper looks like this 3 pin Jumper looks like this Jumper Block looks like this 2 pin Jumper close enabled Looks like this 3 pin Jumper 2 3 pin close enabled Looks like this Jumper Block 1 2 pin close enabled Looks like this PCI 471LF USER S MANUAL 59 550 1 al 1 Page 2 5 Chapter 2 Hardware Configuration 2 4 COM PORT CONNECTOR COMI COMI Connector COMI is fixed as RS 232 The pin assignment is as follows PIN NC 2 2 Connector The 2 is selectable as RS 232 422 485 The pin assignment is as follows PIN 6 DSR RTS 8 CTS NC 9 CTS ne Page 2 6 PCI 471LF USER S MANUAL Chapter 2 Hardware Configuration 2 5 COM1 RI amp VOLTAGE SELECTION JP6 COMI RI amp Voltage Selection The selections are as follows JUMPER JUMPER SELECTION SETTINGS ILLUSTRATION VCC12 Manufacturing Default RI PCI 471LF USER S MANUAL Page 2 7 Chapter 2 Hardware Configuration 2 6 COM2 RI amp VOLTAGE SELECTION JP7 COM2 RI amp Voltage Selection The selections are as follows JUMPER JUMPER SELECTION SETTINGS ILLUSTRATION
41. onfiguration 2 10 EXTERNAL KEYBOARD CONNECTOR EXKBI External Keyboard Connector The pin assignment is as follows ASSIGNMENT L KCLK 2 11 RESET CONNECTOR JPAENL 9 11 Reset Connector The pin assignment is as follows ASSIGNMENT GND 2 12 HARD DISK DRIVE LED CONNECTOR JPAENL 5 7 Hard Disk Drive LED Connector The pin assignment is as follows ASSIGNMENT _3 PCI 471LF USER S MANUAL 1 100000 EXKB1 Reset JPANEL x JPANEL Page 2 11 Chapter 2 Hardware Configuration 2 13 ATX POWER BUTTON JPANEL 10 12 ATX Power Button POWER BUTTON The pin assignment is as follows ASSIGNMENT JPANEL PWB SIOJ 2 14 EXTERNAL SPEAKER CONNECTOR JPANEL 1 3 External Speaker Connector The pin assignment is as follows SPEAKER ASSIGNMENT _ JPANEL 2 15 POWER LED CONNECTOR JPAENL 4 6 8 Power LED Connector RA POWER_LED The pin assignment is as follows 2 20 1 19 ASSIGNMENT J PAN L 6 GND 2 12 PCI 47ILF USER S MANUAL Chapter 2 Hardware Co
42. onnect both DB25 connector and parallel port The pin assignments are as follows PIN PIN ASSIGNMENT Page 2 18 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 25 UNIVERSAL SERIAL BUS CONNECTOR USB1 Universal Serial Bus Connector The pin assignments are as follows 2 26 LAN CONNECTOR LANI LAN Connector The pin assignments are as follows ASSIGNMENT TX TX 2 1 6 RX 8 ISOLATEDGND 9 LED SPLED The green LED detect power link and the Yellow LED is used to detect data active transfer signal PCI 471LF USER S MANUAL Page 2 19 Chapter 2 Hardware Configuration 2 27 ATX POWER CONNECTOR PW1 ATX Power Connector The pin assignments are as follows Slo 1 PW1 2 28 5VSB CONNECTOR JP3 ATX Power Signal Connector The pin assignments are as follows 1 OOO EEE JP3 Page 2 20 PCI 47ILF USER S MANUAL Chapter 2 Hardware Configuration 2 29 PCI SLOT 3 3V VOLTAGE SELECTION JP9 PCI Slot 3 3V Voltage Selection The selections are as follows JUMPER SETTING JUMPER ib pin closed ILLUSTRATION 3 3V from Mainboard 3 3V from Backplane 2 30 INVERTER CONNECTOR JP14 Inverter Connector The pin assignment is as follows aH OGD Og PCI 471LF USER S MANUAL Page 2 21 Chapter 2 Hardware Configuration 2 31 RESET NMI CLEAR WATCHDOG SEL
43. r Password gt PnP PCI Configurations Save amp Exit Setup gt PC Health Status Exit Without Saving Esc Quit Ne Select Item F10 Save amp Exit Setup Time Date Hard Disk Type Setup program initial screen You may use the cursor the up down keys to highlight the individual menu items As you highlight each item a brief description of the highlighted selection will appear at the bottom of the screen PCI 471LF USER S MANUAL Page 4 3 Chapter 4 Award BIOS Setup 4 3 THE STANDARD CMOS FEATURES Highlight the STANDARD CMOS FEATURES and press the lt ENTER gt key and the screen will display the following table Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Wed Jan 1 2003 Item Help Time hh mm ss 22 58 59 Menu Level IDE Primary Master None gt IDE Primary Slave None Change the internal gt IDE Secondary Master None clock IDE Secondary Slave None Drive A None Drive B None Video EGA VGA Halt On Al But Keyboard Base Memory 640K Extended Memory 490496 Total Memory 491520K fi Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults CMOS Setup screen In the above Setup Menu use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item Date
44. rameter allows you to configure the system based on the specific features of the installed chipset The chipset manages bus speed and access to system memory resources such as DRAM and the external cache It also coordinates communications between conventional ISA bus and the PCI bus It must be stated that these items should never need to be altered The default settings have been chosen because they provide the best opera ting conditions for the system The only time you might consider making any changes would be if you discovered that data was being lost while using your system Page 4 10 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup DRAM DATA INTEGRITY MODE Select Parity or ECC error correcting code according to the type of installed DRAM SYSTEM BIOS CACHEABLE Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result VIDEO BIOS CACHEABLE Select Enabled allows caching of the video BIOS resulting in better system performance However if any program writes to this memory area a system error may result MEMORY HOLE AT 15M 16M You can reserve this area of system memory for ISA adapter ROM When this area is reserved it cannot be cached The user information of peripherals that need to use this area of system memory usually discusses their memory requirements DELAYED TRANSACTION
45. s a USB installed on the system board and you want to use it Even when so equipped if you add a higher performance controller you will need to disable this feature 2 USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus USB controller and you have a USB keyboard 3 USB Mouse Support Select Enabled if your system contains a Universal Serial Bus USB controller and you have a USB Mouse 4 Init Display First This item allows you to decide to active whether PCI Slot or on chip VGA first Page 4 14 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup SUPER IO DEVICE The options for these items are found in its sub menu By pressing the lt gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility SuperIO Device Onboard FDC Controller Enabled Item Help Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 UART Mode Select Normal Menu Level X RxD TxD Active Hi Lo X IR Transmission Delay Enabled X UR2 Duplex Mode Half X Use IR Pins IR Rx2Tx2 Onboard Parallel Port 378 IRQ7 Parallel Port Mode SPP X EPP Mode Select EPP1 7 X ECP Mode Use DMA 3 PWRON After PWR Fail Off Ti Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 6
46. st mode for each device 3 Primary Master Slave UDMA Secondary Master Slave UDMA Ultra DMA 33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If you PCI 471LF USER S MANUAL Page 4 13 Chapter 4 Award BIOS Setup hard drive and your system software both support Ultra DMA 33 select Auto to enable BIOS support 4 IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support ONBOARD DEVICE The options for these items are found in its sub menu By pressing the lt gt key you are prompt to enter the sub menu of the detailed options as shown below Phoenix Award CMOS Setup Utility Onboard Device USB Controller Enabled USB 2 0 Support Enabled Item Help USB Keyboard Support Disabled USB Mouse Support Disabled Menu Level gt Onboard LAN Enabled ae Init Display First Onboard Tl Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help 5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Descriptions on each item above are as follows 1 USB Controller This should be enabled if your system ha
47. stem from a soft off state Page 4 18 PCI 471LF USER S MANUAL Chapter 4 Award BIOS Setup RESUME BY ALARM When Enabled your can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode PM EVENTS PM events are I O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode In effect the system remains alert for anything which occurs to a device which is configured as Enabled even when the system is in a power down mode 1 Primary IDE 0 2 Primary IDE 1 3 Secondary IDE 0 4 Secondary IDE 1 5 FDD COM LPT Port PCI 471LF USER S MANUAL Page 4 19 Chapter 4 Award BIOS Setup 4 8 PNP PCI CONFIGURATION Choose PNP PCI CONFIGURATION from the main menu a display will be shown on screen as below Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations igurati Disabl Reset Configuration Data Disabled Item Help Resources Controlled By Auto ESCD Menu Level x IRQ Resources Press Enter Select Yes if you are PCI VGA Palette Snoop Disabled using a Plug and Play capable operating system Select No if you need the BIOS to configure non boot devices fi Move Enter Select PU PD Value 10 5 ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PNP PCI Configuration Setup Screen The PNP PCI Configuration Setup describ
48. t in order for the changes to take effect PCI 471LF USER S MANUAL Chapter 3 Software Configuration 3 6 USB2 0 SOFTWARE INSTALLATION UTILITY 3 6 1 Installation of Utility for Windows 98SE 2000 XP Intel USB 2 0 Enhanced Host Controller driver can only be used on Windows 98SE Windows 2000 and Windows XP on Intel Desktop boards It should be installed right after the OS installation kindly follow the following steps 1 Place insert the Utility Disk into Floppy Disk Drive or CD ROM drive 2 Under Windows 98SE 2000 and XP system go to the directory where Utility Disc is located 3 Start the System wizard in control panel Click Start Settings Control Panel 4 Select Hardware and click Device Manager button 5 Double Click USB Root Hub 6 Select Driver 7 Click Install to install the driver 8 Follow the instructions on the screen to complete the installation 9 Click Finish after the driver installation is complete PCI 471LF USER S MANUAL Page 3 7 Chapter 3 Software Configuration 3 7 WATCHDOG TIMER CONFIGURATION The I O port address of the watchdog timer is 2E hex and 2F hex 2E hex is the address port 2F hex is the data port User must first assign the address of register by writing address value into address port 2E hex then write read data to from the assigned register through data port 2F hex Configuration Sequence To program W83627HF configura
49. tion registers the following configuration sequence must be followed 1 Enter the extended function mode 2 Configure the configuration registers 3 Exit the extended function mode 1 Enter the extended function mode To place the chip into the extended function mode two successive writes of 0x87 must be applied to Extended Function Enable Registers EFERs i e 2Eh 2 Configurate the configuration registers The chip selects the logical device and activates the desired logical devices through Extended Function Index Register EFIR and Extended Function Data Register EFDR EFIR is located at the same address as EFER and EFDR is located at address EFIR 1 First write the Logical Device Number 1 0 07 to the EFIR and then write the number of the desired logical device to the EFDR Secondly write the address of the desired configuration register within the logical device to the EFIR and then write or read the desired configuration register through EFDR 3 Exit the extended function mode To exit the extended function mode one write of OxAA to EFER is required Once the chip exits the extended function mode Example Program 1 Enable watchdog timer and set 30 sec as timeout interval Mov dx 2eh Enter to extended function mode Mov al 87h Out dx al Out dx al Page 3 8 PCI 471LF USER S MANUAL Chapter 3 Software Configuration Mov al 07h Select Logical Device 8 of watchdog timer Out dx al Inc dx
Download Pdf Manuals
Related Search