Intel AI5VG User's Manual
Contents
1. e Sl X Lm mu TET 82C597Al Jl Figure 1 Layout of the AISVG Motherboard AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 3 Hardware Description 3 1 Processor and CPU Voltage The AI5VG is designed to take a Pentium Processor with a bus speed of 60 and 66 MHz The internal clock of the CPU can be multiples of 1 5 2 2 5 3 3 5 4 and 4 5 of the bus clock the CPU frequency can be 90 to 300MHz The onboard CPU voltage regulator provides support for CPUs Vcore which require voltage other than 3 3V such as 2 8V and or power consumption higher than 10 watts 3 2 L2 Cache Memory The AISVG supports 512KB Pipelined Burst Synchronous Cache The P B Synchronous Cache boosts the system s performance 10 higher than regular Asynchronous Cache 3 3 Main Memory The AISVG motherboard supports four 72 pin SIMMs and two 168 pin DIMMs Dual In line Memory Module sockets The DRAMs for the SIMM sockets can be 4MB 8MB 16MB 32MB and 64MB in EDO and FPM types DIMM modules can be 8MB 16MB 32MB 64MB and 128MB in EDO DRAM or SDRAM type The following should be noted when populating the SIMM DIMM sockets 1l SIMMI SIMNO SIMM3 SIMM4 or DIMMI DIMM2 bank can be populated first 2 Each bank should consist of the same size SIMMs 3 Each bank should consist2. 33V 32V K6 166 200 6x86MX 33V 2 5V 2 3V Os 7 Ra AISVG Pentium VP3 Baby AT Motherboard User s Manual 17 Chapter 4 Hardware Settings For Dual Voltage CPU Intel 55 Cyrix 6x86L MX AMD K6 K6 233 2 2V 0 250 K6 233 2 1V 0 251 off off off off jaw 4 3 JP5 Clear CMOS Selection Use 5 a 3 pin header to clear the contents of the CMOS RAM Do not clear the CMOS RAM unless it is absolutely necessary You will lose your password etc 1 5 JP5 1 2 NOTE If you are using an ATX power supply the ATX power connector should be disconnected from the motherboard to be able to clear CMOS 18 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 5 Installation Chapter 5 Installation This chapter describes the connectors and interfaces that the AISVG provides for creating a working system Refer to Figure 3 for the location of the connectors The following items are covered in this chapter Gonnectofs eir tento aen i oe eet 21 5 2 J3 AT Power Supply Connector esee 21 5 3 J2 ATX Power Supply Connector eee 22 5 4 AT Keyboard and PS 2 Mouse Connectors 22 SKS WE RN J OF Serial 23 5 6 J8 Floppy Drive Connector 23 5 7 79 J11 EIDE Connectors 24 5 8 J10 Parallel Port Connector 25 5 9 J T5 FDA Connector ue
3. PnP Load BIOS Defaults PCI ISA PnP Load Setup Defaults RQ 3 assigned RQ 4 assigned t RQ 5 assigned RQ 7 assigned RQ 9 assigned RQ 10 assigned RQ 11 assigned RQ 12 assigned RQ 14 assigned RQ 15 assigned DMA 0 assigned DMA 1 assigned DMA 3 assigned DMA 5 assigned DMA 6 assigned DMA 7 assigned oo 55858 5 5 PNP OS Installed This field allows you to specify if the operating system installed in your system is plug and play aware Note Operating systems such as DOS OS 2 and Windows 3 x do not use PnP Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices automatically However this capability needs you to use a PnP operating system such as Windows 95 The default value is Manual Reset Configuration Data This field allows you to determine whether to reset the configuration data or not The default value is Disabled IRQ3 4 5 7 9 10 11 12 14 15 DMA0 1 3 5 6 7 assigned to These fields allow you to determine the IRQ DMA assigned to the ISA bus and is not available to any PCI slot AISVG Pentium VP3 Baby AT Motherboard User s Manual 45 Chapter 7 LANDesk User Guide CPU to PCI Write Buffer When enabled this option increase the efficiency of the PCI bus to and speed up the execution in the processor By default this field is set to Enabled PCI Dynamic Bursting When enabled this option combines several PCI
4. VGA OFF LPT amp COM LPT COM HDD amp FDD ON ESC Quit V 2 Select Item DMA master OFF F1 Help PU PD Modify Modem Ring Resume Disabled F5 Old Values Shift F2 Color RTC Alarm Resume Disabled F6 Load BIOS Defaults F7 Load Setup Defaults Power Management This field allows you to select the type of power saving management modes There are fours selections for Power Management Disabled No power management Min Power Saving Minimum power management Max Power Saving Maximum power management Only available for SL CPU User Define Each of the ranges are from 1 min to Ihr Except for HDD Power Down which ranges from 1 min to 15 min Default NOTE Inorder to enable the CPU overheat protection feature the Power Management field should not be set to Disabled 42 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide PM Control by APM This field allows you to use the Advanced Power Management device to enhance the Max Power Saving mode and stop the CPU s internal clock If the Max Power Saving is not enabled this will be preset to NO Video Off Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows the BIOS to control the video display card if it supports the DPMS feature Blank Screen This option only writes blanks to
5. Video Off Method Modem Use IRQ Soft Off by PWRBTN HDD Power Down Doze Mode Suspend Mode PM Events 6 7 PNP PCI Configuration PNP OS Installed Resources Controlled by Reset Configuration Data IRQ3 4 5 7 9 10 11 12 14 15 DMA0 1 3 5 6 7 assigned to CPU to PCI Write Buffer PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction PCI Master Read Prefetch PCI 2 Access 1 Retry PCI Master 1 WS Write PCI Master 1 WS Read PCI IRQ Activated by PCI IDE IRQ Map To 6 8 Load BIOS Defaults 0 essent 48 6 9 Load Setup Defaults 48 6 10 Integrated Peripherals esee 49 OnChip Primary Secondary PCI IDE IDE Prefetch Mode IDE HDD Block Mode 30 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide IDE Primary Secondary Master Slave PIO IDE Primary Secondary Master Slave UDMA Onboard FDD Controller Onboard Serial Parallel Port UART 2 Mode Onboard Parallel Mode 6 11 Supervisor User Password sse 51 6 12 IDE HDD Auto Detecton eene 52 6 13 HDD Low Level Format 52 6 14 Save amp Exit Setup 53 6 15 Bet Without Saving i ose donent teen Re 53 AISVG Pentium VP3 Baby AT Motherboard User s Manual 31 Chapter 7 LANDesk User Guide 6 1 BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel Cyrix AMD processors in a standard IBM AT compatible I O system The BIOS provide
6. AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide 6 10 Integrated Peripherals This option sets your hard disk configuration mode and port ROM PCI ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC OnChip IDE First Channel Enabled Onboard Parallel Mode OnChip IDE Second Enabled Channel DE Prefetch Mode Enabled DE HDD Block Mode Enabled DE Primary Master PIO Auto DE Primary Slave PIO DE Secondary Master PIO DE Secondary Slave PIO DE Primary Master UDMA DE Primary Slave UDMA DE Secondary Master UDMA DE Secondary Slave UDMA Auto Onboard FDD Controller Enabled Onboard Serial Port 1 SF8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 ESC Quit V Select Item Uart 2 Mode Standard F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults Onboard Parallel Port 378H IRQ7 F7 Load Setup Defaults OnChip Primary Secondary PCI IDE These fields allow you either to enable or disable the Primary Secondary controller You might choose to disable the controller if you were to add a higher performance or specialized controller IDE Prefetch Mode This field allows your hard disk controller to use prefetch mode to transfer data to increase the performance IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive IDE Primary Secondary Master Slave
7. PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with the controller and CPU directly AISVG Pentium VP3 Baby AT Motherboard User s Manual 49 Chapter 7 LANDesk User Guide The system supports five modes numbered from 0 default to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode IDE Primary Secondary Master Slave UDMA This field allows your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled Onboard FDD Controller This option allows you to select the onboard FDD port Onboard Serial Parallel Port These fields allow you to select the onboard serial and parallel ports and their addresses The default value for these ports are Serial Port 1 3F8 IRQ4 Serial Port 2 2F8 IRQ3 Parallel Port 378H IRQ7 UART 2 Mode This field determines the UART 2 mode in your computer The options are Standard HPSIR and ASKIR Onboard Parallel Mode This field allows you to determine parallel port mode function SPP Normal Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port 50 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide 6 11 Supervisor User Password These two options set the syste
8. VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide Time The time format is Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt or keys to set the current time Primary HDDs Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices Each channel can support up to two hard disks the first is the Master and the second is the Slave To enter the specifications for a hard disk drive you must select first a Type There are 45 predefined types and 4 user definable types are for Enhanced IDE BIOS Type 1 to 45 are predefined Type User is user definable For the Primary Master Slave as well as Secondary Master Slave you can select Auto under the TYPE and MODE fields This will enable auto detection of your IDE drives and CD ROM drive during POST Press lt PgUp gt lt PgDn gt to select a numbered hard disk type or type the number and press the Enter key The hard disk will not work properly if you enter incorrect information for this field If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually If you select Type User related information is asked to be entered to the following items Number of cylinders HEAD Number of read write heads PREC
9. field sets aperture size of the graphics The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The options available are 4M 8M 16M 32M 64M 128M and 256M The default setting is 64M OnChip USB This field allows you either to enable or disable the USB function By default this field is set to Disabled AISVG Pentium VP3 Baby AT Motherboard User s Manual 41 Chapter 7 LANDesk User Guide 6 6 Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn off video display after a period of inactivity ROM PCI ISA BIOS 2A591M29 POWER MANAGEMENT SETUP AWARD SOFTWARE INC Power Management User Define Primary INTR ON PM Control by APM Yes IRQ3 COM2 Primary Video Off Option Suspend gt Off IRQ4 COM1 Primary Video Off Method V H SYNC Blank IRQ5 LPT 2 Primary MODEM Use IRQ 3 IRQ6 Floppy Disk Primary Soft Off by PWRBTN Instant Off IRQ7 LPT 1 Primary RQ8 RTC Alarm Disabled PM Timers RQ9 IRQ2 Redir Secondary HDD Power Down Disabled RQ10 Reserved Secondary Doze Mode Disabled RQ11 Reserved Secondary Suspend Mode Disabled RQ12 PS 2 Mouse Primary RQ13 Coprocessor Primary RQ14 Hard Disk Primary RQ15 Reserved Disabled PM Events
10. is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged ROM PCI ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Mon Aug 19 1996 Time hh mm ss 00 00 00 HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Auto 0 Primary Slave None 0 Secondary Master None 0 Secondary Slave None 0 Drive A 1 44 3 5in Base Memory Drive B None Extended Memory B 15360K Floppy 3 Mode Support Disabled Other Memory 384K Video VGA Halt On All Errors Total Memory 16384 ESC Quit V gt Select Item PU PD Modify F1 Help Shift F2 Change Color At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the F1 key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1 to 12 Date 1to31 Year 1994 to 2079 To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time 34 AISVG Pentium
11. of the same type SIMMs For example SIMMI and SIMM2 are both be EDO or Page Mode Each bank consists of two SIMM slots or one DIMM slot For example SIMM 1 and SIMM 2 are considered as one bank and DIMM 1 as another one 6 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 3 Hardware Description 1 72 pin SIMM 5V EDO DRAM Bank0 Bank Total Memory SIMM1 SIMM2 SIMM3 SIMM4 mx eme M Jop 3MB 32MBx2 amp MPO DMR 4MP2 4MBx2 4MBx2 16MB 8MBx2 4MBx2 24MB 16MBx2 4MBx2 40MB 64MBx2 16MBx2 160MB 64MBx2 64MBx2 256MB AISVG Pentium VP3 Baby AT Motherboard User s Manual 7 Chapter 3 Hardware Description 2 168 pin DIMM 3 3V SDRAM or EDO DRAM M M IMB o 16 7 9MB 3M 3 4 BIOS The BIOS on the AISVG motherboard provides the standard BIOS functions plus the following additional features 1 DMI Desktop Management Interface The motherboard supports DMI to enable computer system management in an enterprise 2 ISA Plug and Play PnP Extension Unlike PCI cards which are plug and play ISA cards require setting jumpers to resolve hardware conflicts To make a computer system PnP an ISA PnP standard is established and supported by new OSes such as Windows 95 Under Windows 95 the motherboard BIOS must have ISA PnP extension to support the new IS
12. the AISVG motherboard 4 1 5 1 1 8 CPU Frequency Selector sess 14 4 2 SW2 1 4 CPU Voltage Selector eese 16 4 3 JP5 Clear CMOS Selection sese 18 For the locations of the jumpers refer to Figure 2 on the following page The following examples show the conventions used in this chapter Switch 1 and switch 2 are set to OFF Switch 3 and switch 4 are set to ON 12 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 4 Hardware Settings Figure 2 Jumper Locations of the AISVG AISVG Pentium VP3 Baby AT Motherboard User s Manual 13 Chapter 4 Hardware Settings 4 1 SW1 1 8 CPU Frequency Selector For Intel Pentium CPU S WI Clock Mutiplier CPU FREQ ere 5 6 off off off off off off off HCH 5 6 off off off off off off off off ifr EE off off off on off off off Te off off off off on off off off D CG off off off o off off 2 33 off off off off on on off off nore 20 off off off off off on off off rT k i 66MHz 55 233 off off off off off off off off 55 Pentium with MMX technology NOTE
13. 00 233 L2 Cache 512KB Pipelined Burst Synchronous SRAM onboard Main Memory Four 72 pin SIMM sockets and two 168 pin DIMM sockets Memory Type SIMMs FPM Fast Page Mode or EDO Extended Data Out SIMM Size 4MB 8MB 16MB 32MB 64MB DIMMs EDO DRAM or SDRAM Synchronous DRAM DIMM Size 8MB 16MB 32MB 64MB 128MB Chipset VIA s VP3AT chipset with built in PCI EIDE Onboard I O Winbond W83877 for two serial one parallel one floppy drive interface and IrDA support 2 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 2 Specifications Onboard Bus Mastering EIDE Two EIDE interfaces for up to four devices support PIO Mode 3 4 or Ultra DMA 33 IDE Hard Disk and ATAPI CD ROM BIOS Licensed BIOS with additional features FLASH EEPROM 128KB for BIOS update e ISA Plug and Play PnP extension e Power management CPU Temperature Sensor The AD22105 IC on the motherboard is a temperature sensor for the CPU When the CPU temperature exceeds threshold value the CPU slows down automatically to allow it to cool down to a safe level Windows 95 Shut Down This allows the PC to power off via Windows 95 operating system This feature requires ATX power supply AGP Support Accelerated Graphics Port The AISVG motherboard comes with an AGP slot for an AGP VGA card that supports 133MHz 2X mode for AD and SBA signaling PC97 Compliance The AISVG implements BIOS and hardware designs that meet PC97 standards and is fully compa
14. A PnP cards 8 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 3 Hardware Description 3 Power Management The power management feature provides power savings by slowing down the CPU clock turning off the monitor screen and stopping the HDD spindle motor 3 5 Onboard PCI EIDE The PCI EIDE controller is part of the VP3AT chipset It supports PIO mode 3 4 and bus mastering The peak transfer rate of PIO mode 3 4 can be as high as 17MB sec Using HDDs that support bus mastering the peak transfer rate can reach 22MB sec There are two IDE connectors primary IDE and secondary IDE With two devices per connector up to four IDE drives are supported The VP3AT also supports Ultra DMA 33 a new synchronous DMA protocol for faster data transfers 3 6 Onboard Multi I O The onboard multi I O chip Winbond W83877 supports two 16550 UART compatible serial ports one high speed EPP ECP parallel port and one floppy controller The floppy controller supports 2 88MB format The I O port addresses of the serial and parallel ports are programmable via BIOS set up 3 7 Onboard CPU Temperature Sensor The AD22105 IC on the motherboard is a temperature sensor for the CPU When the CPU temperature exceeds threshold value the CPU slows down automatically to allow it to cool down to a safe level AISVG Pentium VP3 Baby AT Motherboard User s Manual 9 Chapter 3 Hardware Description 3 8 I O Port Address Map Each peripheral de
15. AISVG Pentium VP3 Baby AT Motherboard User s Manual Version 2 0 Contents Contents Chapter 1 Introduction 1 Chapter 2 Specifications sossessocsooesessoesooesosssesoossossseso 2 Chapter 3 Hardware Description 4 3 1 Processor and CPU Voltage AAA 6 3 2 L2 Cache Memory eae ice 6 3 3 Main Memory lee rie bo HR 6 3 4 BIOS i o PR RR RS 8 3 5 Onboard PCF EIDE eR id 9 3 6 Onboard Malo 9 3 7 Onboard CPU Temperature 9 3 8 Port Address Map 10 AH Channels secte ee nenne eee ms 10 3 10 Interrupt Request Lines 11 3 11 Accelerated Graphics Port AGP Slot 11 Chapter 4 Hardware Settings 12 4 1 SW1 1 8 CPU Frequency Selector 14 4 2 SW2 1 4 CPU Voltage Selector 16 4 3 JP5 Clear CMOS Selection 18 Chapter 5 Installation eee eere eren 19 5 1 RE One 21 5 2 13 AT Power Supply 21 5 3 J2 ATX Power Supply 22 5 4 J4 AT Keyboard and PS 2 Mouse Connectors 22 5 9 J7 Jo Senal 23 5 6 J8 F
16. DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Select Primary Master Option N SK EUN EM RN EN 18 NOTE Some OSes like SCO UNIX must use NORMAL for installation Up to four IDE drives can be detected with parameters for each appearing in sequence inside a box To accept the displayed entries press the Y key to skip to the next drive press the N key If you accept the values the parameters will appear listed beside the drive letter on the screen 6 13 HDD Low Level Format This option should only be used by a professional Low level formatting can cause irreparable damage to your hard disk The procedures include selecting the drive you want to low level format determining the bad tracks and proceeding with pre formatting 52 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide 6 14 Save amp Exit Setup This option allows you to determine whether to accept the modifications or not If you type you will quit the setup utility and save all changes into the CMOS memory If you type you will return to Setup utility ROM BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC I STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAQ CONFI LOAD BIOS DET LOAD SETUP D ESC Quit F10 Save amp Exit Setup SUPERVISOR PASSWORD USER PASSWORD ETEC
17. High Gate A20 Option Fast Memory Parity ECC Check Disabled Typematic Rate Setting Disabled Typematic Rate chars Sec 6 Typematic Delay Msec 250 Security Option Setup PCI VGA Palette Snoop Disabled OS Select For DRAM gt 64MB Non OS2 ESC Quit V 2 Select Item F1 Help PU PD Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning message If this occurs you can either allow the operation to continue or run an anti virus program to locate and remove the problem NOTE Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning If you will run such a program disable the Virus Warning feature CPU Internal Cache External Cache These items allow you to enable speed up memory access or disable the cache function By default these items are Enabled AISVG Pentium VP3 Baby AT Motherboard User s Manual 37 Chapter 7 LANDesk User Guide Quick Power On Self Test This choice speeds up the Power On Self Test POST after you power up the system If it is set to Enabled BIOS will skip some items By default this choice is Enabled Boot Sequence This field determines the drive that the system searches first for an ope
18. LANDesk User Guide ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE ING STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAGEMENT SETUP IDE HDD AUTO DETECTION PNP PCI CONFIGURATION HDD LOW LEVEL FORMAT LOAD BIOS DEFAULTS SAVE amp EXIT SETUP LOAD SETUP DEFAULTS EXIT WITHOUT SAVING ESC Quit VY gt Select Item F10 Save amp Exit Setup Shift F2 Change Color Time Date Hard Disk Type The section below the setup items of the Main Menu displays the control keys for this menu Another section at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list NOTE After making and saving system changes with Setup you find that your computer cannot boot the Award BIOS supports an override to the CMOS settings that resets your system to its default We strongly recommend that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability AISVG Pentium VP3 Baby AT Motherboard User s Manual 33 Chapter 7 LANDesk User Guide 6 3 Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the motherboard
19. OMP Write precompensation LANDZ Landing zone SECTOR Number of sectors SIZE Automatically adjust according to the configuration MODE for IDE HDD only Auto Normal HD 528MB Large for MS DOS only LBA HD gt 528MB and supports Logical Block Addressing AISVG Pentium VP3 Baby AT Motherboard User s Manual 35 Chapter 7 LANDesk User Guide NOTE The specifications of your drive must match with the drive table The hard disk will not work properly if you enter incorrect information in these fields If your hard disk drive type is not matched or listed you can use Type User to define your own drive type manually Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are 360KB 12MB 720KB 144MB 288MB 5 25in 5 25 3 5in 3 5 3 5 in Floppy 3 Mode Support This is the Japanese standard floppy drive The standard stores 1 2MB in 3 5 inch diskette You have four options to choose Disabled No 3 mode floppy drive installed default Drive A Installed 3 mode drive at drive A Drive B Installed 3 mode drive at drive B Both Installed 3 mode drive at drive A and B Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA For EGA VGA SEGA SVGA or PGA monitor adapters default CGA 40 Power up in 40 column mode CGA 80 Power
20. SWI 4 and SW1 8 are inconsequential They could be set to either ON or OFF 14 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 4 Hardware Settings For Cyrix 6x86 6x86L CPU D BusClock Mutiplier CPU FREQ off off off on off off off off off off off on off off off For Cyrix 6x86MX CPU lz 241265 r off off off off o off off ETE off off off off off on off com as off off off off off off off For AMD 5 CPU Bus Clock Mutiplier CPU FREQ off o off off off 66MHz PR100 s 8 T off off off off off off off off E e T 66MHz PR133 l2 232456 r off off off off on off off off AISVG Pentium VP3 Baby AT Motherboard User s Manual 15 Chapter 4 Hardware Settings ST Pes Clock _Mutiplier PREG Bus Clock Mutiplier CPU FREQ me off off off off on on off off L l L23456 785 off off off off off on off off ON i L23456 F865 off off off off off off off off 4 2 SW2 1 4 CPU Voltage Selector For Single Voltage CPU Intel P54C Cyrix 6x86 AMD K5 C6 on on on on For Dual Voltage CPU Intel P55C Cyrix 6x86L MX AMD K6 m Yo Yom HAM HED i a m EN 34 off on on 16 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 4 Hardware Settings For Dual Voltage CPU Intel P55C Cyrix 6x86L MX AMD K6 K6 233 0 350
21. TION FORMAT V gt Select Item Shift F2 Change Color Save Data to CMOS amp Exit Setup 6 15 Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing will quit the Setup utility without saving the modifications Typing will return you to Setup utility ROM BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAG LOAD BIOS D I INTEGRATED PERIPHERALS SUPERVISOR PASSWORD USER PASSWORD ETECTION FORMAT ESC Quit Select Item F10 Save amp Exit Setup Shift F2 Change Color Abandon all Data amp Exit Setup AISVG Pentium VP3 Baby AT Motherboard User s Manual 53
22. atically determine your IDE disk system configuration AISVG Pentium VP3 Baby AT Motherboard User s Manual 47 Chapter 7 LANDesk User Guide 6 8 Load BIOS Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features ROM BIOS CMOS SETUP UTILITY AWARD SOFTWARE INC I STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAG PNP PCI CONFI LOAD BIOS DEI LOAD SETUP D ESC Quit F10 Save amp Exit Setup Load BIOS Defaults except Standard CMOS Setup To load BIOS defaults value to CMOS SRAM enter If not enter 6 9 Load Setup Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE ING STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANA ETECTION CONFI FORMAT LOAD BIOS D I LOAD SETUP D ESC Quit lt Select Item F10 Save amp Exit Setup Shift F2 Change Color Load BIOS Defaults except Standard CMOS Setup To load SETUP defaults value to CMOS SRAM enter If not enter N 48
23. cycles into one By default this field is set to Disabled PCI Master 0 WS Write When enabled this option increases the write cycle speed By default this field is set to Disabled PCI Delay Transaction When enabled this option delays PCI data transaction By default this field is set to Disabled PCI Master Read Prefetch When this item is enabled the system is allowed to prefetch the next read and initiate the next process By default this field is set to Disabled PCI 2 Access 1 Retry This item enables PC 2 Access 1 attempts By default this field is set to Disabled PCI Master 1 WS Write When enabled writes to the PCI bus are executed with 1 wait states By default this field is set to Disabled PCI Master 1 WS Read When enabled reads to the PCI bus are executed with 1 wait states By default this field is set to Disabled PCI IRQ Activated by This field allows you to select the method by which the PCI bus recognizes that an IRQ service is being requested by a device The default value is Level 46 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide PCI IDE IRQ Map To This field allows you to configure the type of IDE disk controller in your system The default setup is ISA If you have equipped with PCI controller you need to specify which slot has the controller and PCI interrupt is associated with the connected hard drives Selecting PCI AUTO allows the system to autom
24. d CPU Wt Pipeline When enabled this item allow pipelining of cache reads and CPU writes The default setting is Enabled Read Around Write DRAM optimization feature If a memory read is addressed to a location whose latest write is being held in a buffer before being written to memory the read is satisfied through the buffer contents and the read is not sent to the DRAM The default setting is Enabled 40 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide Cache Timing This field sets the timing of the cache in the system The options are Fast and Fastest By default this field is set to Fast Video BIOS Cacheable When enabled access to video BIOS addressed at COOOOH to C7 FFFH are cached provided that the cache controller is enabled System BIOS Cacheable When enabled access to the system BIOS ROM addressed at F0000H FFFFFH are cached provided that the cache controller is enabled Memory Hole at 15 Addr In order to improve performance certain space in memory can be reserved for ISA cards This field allows you to reserve 15 to 16MB memory address space to ISA expansion cards This makes memory from 15MB and up unavailable to the system Expansion cards can only access memory up to 16 By default this field is set to Disabled AGP This field enables or disables the AGP Accelerated Graphics Port function on the motherboard The default setting is Enabled Aperture Size The
25. e connectors 1 2 RXD Receive data 5 GND ground 6 DSR Datasetready CTS Clearto send 9 RLRingindiator 5 6 J8 Floppy Drive Connector J8 of the AISVG is a 34 pin header and will support up to 2 88MB floppy drives Pin 7 1 Ground Ground 2 Ground 2 Ground 2 Ground 2 Gromd 2 Ground 3 Ground 3 Diskette change 6 8 AISVG Pentium VP3 Baby AT Motherboard User s Manual 23 Chapter 3 Installation 5 7 J9 J11 EIDE Connectors 24 J9 Primary IDE Connector Signal Name Pin A Signal Name Host data 7 3 4 Host data 8 6 Hostdata9 8 HostdatalO Hostdatad 9 40 J11 Secondary IDE Connector Pin 1 LA 2 4 1 36 Chip select 0 Chip select 1 Activity 39 40 Ground AISVG Pentium VP3 Baby AT Motherboard User s Manual NIN 2 2 SC 4 4 6 Ree 27 28 36 40 7 3 3 35 LA Chapter 5 Installation 5 8 J10 Parallel Port Connector The following table describes the pin out assignments of this connector Line printer strobe 1 14 AutoFeed Error PD4 parallel data4 6 PDS parallel data 5 20 PD6 parallel data6 8 PD7 parallel data 7 9 11 24 Busy Ground nu nu nu nu nu n
26. e the Video BIOS location from ROM to RAM Video Shadow will increase the video speed C8000 CBFFF Shadow DC000 DFFFF Shadow Shadowing a ROM reduces the memory available between 640KB to 1024KB These fields determine whether optional ROM will be copied to RAM or not AISVG Pentium VP3 Baby AT Motherboard User s Manual 39 Chapter 7 LANDesk User Guide 6 5 Chipset Features Setup This Setup menu controls the configuration of the motherboard chipset ROM PCI ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC 0 1 DRAM Timing OnChip USB Disabled 2 3 DRAM Timing 4 5 DRAM Timing DRAM Read Pipeline Enabled Sustained 3T Write Enabled Cache Rd CPU Wt Pipeline Enabled Read Around write Enabled Cache Timing Fast Video BIOS Cacheable Enabled System BIOS Cacheable Disabled Memory Hole At 15MB Disabled ESC Quit V gt Select Item AGP Enabled F1 Help PU PD Modify Aperture Size 64M F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults Bank DRAM Timing These fields defines the speed of the DRAM memory onboard The options are Normal Medium Fast Turbo 70ns and 60ns By default these fields are set to 60ns DRAM Read Pipeline When enabled this field supports pipelining of DRAM reads The default setting is Enabled Sustained 3T Write This field allows support for PBSRAM sustained 3T write By default this field is set Enabled Cache R
27. erate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds You can select speed range from 6 to 30 characters per second By default this item is set to 6 Typematic Delay Msec When the typematic rate is enabled this item allows you to set the time interval for displaying the first and second characters By default this item is set to 250msec Security Option This field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether MPEG ISA VESA VGA Cards can work with PCI VGA or not When this field is enabled a PCI VGA can work with a MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with a MPEG ISA VESA Card OS Select for DRAM gt 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends on certain BIOS calls to access memory The default setting is NON OS 2 Video BIOS Shadow This item allows you to chang
28. for audio tone generation An 8 ohm speaker is recommended J20 Pin Signal Name 1 10 Power LED and Keylock Pins 11 15 The power LED indicates the status of the main power switch The keylock switch when closed will disable the keyboard function 10 oo oo o ATX Power ON Switch Pins 7 and 17 This 2 pin connector is an ATX Power Supply On Off Switch on the motherboard that connects to the power switch on the case When pressed for more than 4 seconds the power switch will force the motherboard to power off When pressed for less than 4 seconds it will force the motherboard to enter the Suspend Mode depending on BIOS presettings 1 10 Turbo LED Connector Pins 8 and 18 There is no turbo deturbo function on the motherboard The Turbo LED on the control panel will always be On when attached to this connector 1 10 J20 Pin Signal Name bs 5V AISVG Pentium VP3 Baby AT Motherboard User s Manual 27 Chapter 5 Installation 28 1 naaagaagaaadu Reset Switch Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch Off and then On Orientation is not required when making a connection to this header 1 10 P D Hard Disk Drive LED Connector Pins 10 and 20 This connector connects to the hard drive activity LED on co
29. interrupts itself and performs the service The default value is Off When set On activity will neither prevent the system from going into a power management mode nor awaken it The IRQ section sets the wake up call of the system If activity is detected from any enabled IRQ channels in the left hand group the system wakes up from suspended mode 44 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide 6 7 PNP PCI Configuration This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value ROM PCI ISA BIOS CHIPSET FEATURES SETUP AWARD SOFTWARE INC PNP OS Installed No CPU to PCI Write Buffer Enabled Resources Controlled by Manual PCI Dynamic Bursting Enabled Reset Configuration Data Disabled PCI Master 0 WS Write Enabled PCI Delay Transaction Enabled Legacy ISA PCI Master Read Prefetch Enisabled Legacy ISA PCl 2 Access 1 Retry Disabled PnP Master 1 WS Write Enabled Legacy ISA Master 1 WS Read Disabled PnP POI ISA PnP PCI IRQ Activated By Level PnP PCI IDE IRQ Map To PCl Auto PCI ISA PnP Primary IDE INT iA PCI ISA PnP Secondary IDE INT PnP PnP PnP ESC Quit V Select Item PnP Help PU PD Modify PCI ISA Old Values Shift F2 Color
30. loppy Drive Connector 23 5 7 J9 J11 EIDE 6 eR 24 5 8 J10 Parallel Port Connector 25 5 9 J15 IrDA Connector essere 25 5 10 J5 USB Connector iinee itte tit tite poii 25 5 11 J13 Wake on LAN Connector 26 5 12 J14 CPU Fan Power Connector esses 26 5 13 J20 Front Bezel Connector sessar nenna 26 AISVG Pentium VP3 Baby AT Motherboard User s Manual i Contents Chapter 6 BIOS Configurration ccsccsssscscssseesees 29 6 1 BIOS Introduction ien iE 32 6 2 BIOS Setup incedunt 32 6 3 Standard CMOS Setup 34 6 4 BIOS Features Setup 37 6 5 Chipset Features Sep 40 6 6 Power Management Setup 42 6 7 PNP PCI Configuration esee 45 6 8 Load BIOS Defaults 48 6 9 Load Setup Defaulte A 48 6 10 Integrated Peripherals eene 49 6 11 Supervisor User eese 51 6 12 IDE HDD Auto Detection eee 52 6 13 HDD Low Level Format 52 6 14 Save amp Exit Setup 53 6 15 Exit Without Sang 53 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 1 Introduction Chapter 1 Introduction This manual is designed to give you information on the AISVG Motherboard It is divided into the following six sections Introduction Specifications Hardware Description Hardware Setting
31. m password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press lt Enter gt The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the lt Enter gt key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely ROM PCI ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE ING STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP SUPERVISOR PASSWORD CHIPSET FEATURES SETUP USER PASSWORD POWER MANAG FORMAT LOAD BIOS D I ESC Quit Select Item F10 Save amp Exit Setup Shift F2 Change Color Change Set Disable Password AISVG Pentium VP3 Baby AT Motherboard User s Manual 51 Chapter 7 LANDesk User Guide 6 12 IDE HDD Auto Detection This option detects the parameters of an IDE hard disk drive and automatically enters them into the Standard CMOS Setup screen ROM BIOS STANDARD CMOS SETUP AWARD SOFTWARE INC HARD
32. ntrol panel This LED will flash when the HDD is being accessed 10 J20 Pin Signal Name Ground AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide Chapter 6 BIOS Configuration This chapter describes the different settings available in the Award BIOS that comes with the AISVG motherboard The topics covered in this chapter are as follows 6 1 BIOS Iotroducnon eene 32 6 2 BIOS EE 32 6 3 Standard CMOS Sep 34 Date Time Primary HDDs Secondary HDDs Drive Drive Floppy 3 Mode Support Video Halt On 6 4 BIOS Features Setup egre tenter 37 Virus Warning CPU Internal Cache External Cache Quick Power On Self Test Boot Sequence Swap Floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Boot Up System Speed Gate A20 Option Memory Parity ECC Check Typematic Rate Setting Typematic Rate Chars Sec Typematic Delay Msec Security Option PCI VGA Palette Snoop OS Select for DRAM 64MB Video BIOS Shadow C8000 CBFFF Shadow DC000 DFFFF Shadow 6 5 Chipset Features Setup 40 Bank DRAM Timing DRAM Read Pipeline Sustained 3T Write AISVG Pentium VP3 Baby AT Motherboard User s Manual 29 Chapter 7 LANDesk User Guide Cache Rd CPU Wt Pipeline Read Around Write Cache Timing Video BIOS Cacheable System BIOS Cacheable Memory Hole at 15 Addr AGP Aperture Size OnChip USB 6 6 Power Management Setup 42 Power Management PM Control by APM
33. rating system The options are A C SCSI D A SCSI SCSI A C A SCSI E A SCSI C CDROM A F A SCSI LS ZIP C CDROM C A SCSLA C The default value is A C SCSI Swap Floppy Drive This item allows you to determine whether to enable Swap Floppy Drive or not When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek When enabled the BIOS will seek whether or not the floppy drive installed has 40 or 80 tracks 360K type has 40 tracks while 760K 1 2M and 1 44M all have 80 tracks By default this field is set to Enabled Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system By default the system boots up with NumLock On Boot Up System Speed This has no function and selects the default system speed High Gate A20 Option This field allows you to select how Gate A20 is worked The Gate A20 is a device used to address memory above 1 MB By default this field is set to Fast Memory Parity ECC Check Set this option to Enabled when the memory installed in your system supports ECC error correction code or parity By default this field is set to Disabled 38 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide Typematic Rate Setting When disabled continually holding down a key on your keyboard will gen
34. re retenti 25 5 10 J5 USB 25 5 11 J13 Wake on LAN Connector eee 26 5 12 J14 CPU Fan Power Connector 26 5 13 J20 Front Bezel Connector 26 AISVG Pentium VP3 Baby AT Motherboard User s Manual 19 Chapter 5 Installation M2 1111121115 BIOS J7 1202191211191 2222 6 COMI J2 Tr Figure 3 Connector Location on the AISVG 20 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 5 Installation 5 1 T O Connectors The I O connectors connect the AISVG to the most common peripherals To attach cables to these connectors carefully align Pin 1 of the cables to that of the connectors Refer to Figure 4 for the location and orientation of the connectors RED MARK CABLE Figure 4 Orientation of the I O Connector 5 2 J3 AT Power Supply Connector When using an AT compatible power supply plug both of the power supply connectors into J3 Make sure the power supply connectors are connected in the right orientation The power supply connec
35. s Installation BIOS Configuration Checklist Please check that your package is complete and contains the items below If you discover damaged or missing items please contact your dealer lt gt The AISVG Motherboard lt This user s manual lt gt 1 IDE ribbon cable 1 floppy ribbon cable 2 serial ribbon cables 1 parallel ribbon cable 1 PS 2 cable 1 diskette containing Bus Master IDE drivers and and flash utility 1 diskette containing VxD drivers Use the two serial ribbon cables provided to avoid compatibility problems AISVG Pentium VP3 Baby AT Motherboard User s Manual 1 Chapter 2 Specifications Chapter 2 Specifications Based on VIA s VP3AT chipset the AISVG is a Baby AT Pentium motherboard that supports all the features to make a Microsoft PC 97 compliant PCI ISA system This high performance model comes with an Accelerated Graphics Port AGP slot power management functionality that is compliant with ACPI Advanced Configuration and Power Interface and legacy APM requirements In addition to standard PIO and DMA mode operation the AISVG features Ultra DMA 33 for improved disk I O throughput The main features of this motherboard are listed as follows Main Processor Intel Pentium 90 100 120 133 150 166 200 Intel Pentium MMX P55C 90 100 120 133 150 166 200233 Cyrix 6x86 6x86L 150 166 200 Cyrix 6x86MX PR166 PR200 PR233 PR266 AMD K5 PR100 PR133 PR166 AMD 166 2
36. s critical low level support for standard devices such as disk drives serial and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system 6 2 BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately activated Pressing the lt Del gt key immediately allows you to enter the Setup utility If you are a little bit late pressing the lt Del gt key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items lt Enter gt to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and lt Esc gt to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices 32 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7
37. the video buffer Modem Use IRQ This field defines the IRQ being used by the modem By default the the IRQ is set to 3 Soft Off by PWRBTN This field defines the power off mode when using an ATX power supply The Instant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds The default value is Instant Off HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Doze Mode When enabled and after the set time of system inactivity the CPU clock will run at a slower speed while all other devices still operate at full speed Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off AISVG Pentium VP3 Baby AT Motherboard User s Manual 43 Chapter 7 LANDesk User Guide PM Events The VGA LPT amp COM HDD amp FDD DMA master Modem Ring Resume RTC Alarm Resume and Primary INTR section are I O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode When an I O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it
38. tible with all Windows operating systems Expansion Slots Four 32 bit PCI slots Two 16 bit ISA slots One AGP slot Form Factor Baby AT 9 x8 6 23cm x 22cm AISVG Pentium VP3 Baby AT Motherboard User s Manual 3 Chapter 3 Hardware Description Chapter 3 Hardware Description This chapter briefly describes each of the major features of the AISVG motherboard The layout of the board is shown in Figure 1 which shows the locations of the key components The topics covered in this chapter are as follows 3 1 Processor and CPU Noltage sese 6 3 2 122 Cache Memory oett ede eee ti tees 6 3 3 Main Memor 6 34b BIOS aedi ERE RE RUD ius 8 3 5 Onboard PGI BIDE ed n ead beet 9 3 6 Onboard Mul IO 9 3 7 Onboard CPU Temperature Sensor 9 3 8 I O Port Address Map et er tete 10 3 9 DMA Channels 5 eer Aere 10 3 10 Interrupt Request Lines IRQ eene 11 3 11 Accelerated Graphics Port AGP 510 11 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 3 Hardware Description 1900 6 COM2 efe 4 BIOS 6 COM1 J2 MN JOO 20102000006 EE S
39. tors are connected in the right orientation if the black wires of each power cable are ADJACENT to each other That is black wires of each connector should be aligned in the center of the J3 power supply connector J3 Pin Description Wire Color 1 Power Good Orange 2 e Red 3 e IN Yellow 4 e LI7N Blue 5 Ground Black 6 Ground Black 7 Ground Black 8 Ground Black 9 e 5V White 10 e 15V Red 11 e 15V Red 12 e 15V Red AISVG Pentium VP3 Baby AT Motherboard User s Manual 21 Chapter 5 Installation 5 3 J2 ATX Power Supply Connector J2 is a 20 pin ATX power supply connector Refer to the following table for the pin out assignments jai _ Signal Name Signal Name on EN n qu pos ew per pv EC 39V 7 ae Ground B f 3 fo Ground o EE Ground 16 6 va Grund 17 7 Ground 18 8 Power good 25 9 ww 2 2 10 12V 5 4 J4 AT Keyboard and PS 2 Mouse Connectors AT Keyboard Connector Signal Name 1 Keyboard clock d data Ss J4 PS 2 Mouse Connector 1 1 Mouse dan EC UR Na ND n Mouse Clock d 22 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 5 Installation 5 5 J7 J6 Serial Ports The onboard serial ports of the AISVG are 10 pin header connectors J7 is COMI and J6 is 2 The following table shows the pin out of the thes
40. u nu nu na nu nu nu Paper empty 5 9 J15 IrDA Connector This connector is used for an IrDA connector that supports infrared wireless communication with IrDA devices 5V Ir RX 5 IRRX IRTX N C GND 5 10 J5 USB Connector J5is the USB connector on AISVG The following table shows the pin out assignments of these connectors ee 9e AISVG Pentium VP3 Baby AT Motherboard User s Manual 25 Chapter 5 Installation 5 11 J13 Wake on LAN Connector J13is a 3 pin header for Wake on LAN function on the motherboard Signal Name 5VSB 2 1253 Wake on LAN Ground 5 12 J14 CPU Fan Power Connector 11415 a 3 pin header for the CPU fan power connector The fan must be a 12V fan Pin Signal Name 12 3 5 13 J20 Front Bezel Connector The front bezel of the case has a control panel which provides light indication of the computer activities and switches to change the computer status J20 is a 20 pin header that provides interfaces for the following functions Hard Disk Drive LED Reset Switch Turbo LED Connector ATX Power On Switch mau Not Defined V Power LED and Keylock Speaker gm D 26 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 5 Installation Speaker Pins 1 4 This connector provides an interface to a speaker
41. up in 80 column mode MONO For Hercules or MDA adapters Halt On This field determines whether the system will halt if an error is detected during power up No errors Whenever the BIOS detects a non fatal error the system will stop and you will be prompted All errors The system boot will not be halted for any error that may be detected default All But Keyboard The system boot will not be halted for a keyboard error it will stop for all other errors But Diskette The system boot will not be halted for a disk error it will stop for all other errors All But Disk Key The system boot will not be halted for a key board or disk error it will stop for all others 36 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 7 LANDesk User Guide 6 4 BIOS Features Setup This section allows you to configure and improve your system and allows you to set up some system features according to your preference ROM PCI ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Disabled Video BIOS Shadow Enabled CPU Internal Cache Enabi C8000 CBFFF Shadow Disabled External Cache Enabi CC000 CFFFF Shadow Disabled Quick Power On Self Test Enabi D0000 D3FFF Shadow Disabled Boot Sequence C SCSI D4000 D7FFF Shadow Disabled Swap Floppy Drive Disabled D8000 DBFFF Shadow Disabled Boot Up Floppy Drive Enabled DC000 DFFF Shadow Disabled Boot Up Numlock Status On Boot Up System Speed
42. vice in the system is assigned a set of I O port addresses which also becomes the identity of the device There are a total of 1K port address space available The following table lists the I O port addresses used on the motherboard Device Desc iption 040h 05Fh Timer 060h 06Fh Keyboard Controller O0COh ODFh Controller 2 EGA adapter 3F7h 360 36 Network Ports 3 9 DMA Channels There are seven DMA Channels available on the motherboard Only DMA2 is used by the floppy controller In the case that ECP mode on the parallel port is used 1 or DMA3 will be used 10 AISVG Pentium VP3 Baby AT Motherboard User s Manual Chapter 3 Hardware Description 3 10 Interrupt Request Lines IRQ There are a total of 15 IRQ lines available on the motherboard Peripheral devices use interrupt request lines to notify the CPU for the service required The following table shows the IRQ used by the devices on the motherboard Keyboard Interrupt Cascade Serial Port 2 Reserved 3 11 Accelerated Graphics Port AGP Slot The AISVG motherboard comes with an AGP slot for an AGP VGA card that supports 133MHz 2X mode for AD and SBA signaling to provide high performance 3D graphic display AISVG Pentium VP3 Baby AT Motherboard User s Manual 11 Chapter 4 Hardware Settings Chapter 4 Hardware Settings The following sections describe the necessary procedures and proper jumper settings to configure
Download Pdf Manuals
Related Search