Home

Initio I/O HIGHWAY User's Manual

1. D Disable support for fixed disk drive initio IBM OS 2 Driver installation Overview The I OHIGHWAY OS 2 driver will support OS 2 3 0 amp 4 0 The device driver for OS 2 is copied from the INI 9XXXU 9XXXUW DRIVER DISK 1 to your hard drive where it is initialized during boot up The installation of Initio device drivers to support OS 2 include the following software files and may be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 OS2 INI910U ADD INI 9XXX SCSI Host Adapter OS 2 driver OS2 INI910U DDP Script file for installing INI910U ADD Installation The INI 9XXX driver developed for OS 2 will be installed on the disk drive used for system initialization The driver is loaded during the system boot routine and will remain resident on the drive Installation of the drivers can be accomplished by following one of the procedures listed e New OS 2 Installation e Adding INI 9XXX host adapter to existing OS 2 The steps used to install the Initio drivers have different system requirements that may affect basic operation if not installed properly It is strongly suggested that the selected procedure be read and understood before proceeding Please read all instructions carefully New OS 2 installation These instructions will guide you through the Initio OS 2 device driver and OS 2 installa tion at the same time The program can be installed from floppy diskettes or from CD ROM The OS 2 driver for the INI 9XXX will be fo
2. e At window Insert Disk labled INI 9XXXU 9XXXUW driver select OK e At window titled Copying file replace the highlighted directory path with A WIN95 then select OK this will complete loading the INI910U MPD driver onto your hard disk drive Following installation of the Initio INI 9XXXU UW Windows 95 driver reboot your sys tem to activate the SCSI device driver initio P Microsoft Windows 95 95b OSR2 Driver Installation 4 It is highly recommended that you verify Initio s Windows 95 device driver by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed This completes loading the Host Adapter Driver follow the on screen directions to com plete the Windows 95 installation Exit and reboot the system to activate the device driver Adding the Initio Driver to an Existing Windows 95B OSR2 System These instructions will guide you through the installation of the Initio host adapter to an existing Windows 95 system Windows 95 will automatically detect the presence of new hardware in Plug and Play com
3. User S Manual Initio Corporation 2188 B Del Franco Street San Jose California 95131 1575 http www initio com Copyright Copyright 1998 Initio Corporation All rights reserved This document may not in whole or part be copied reproduced reduced or translated by any means either mechanical or eletronic without prior consent in writing from Initio Corporation Initio Corporation assumes no responsibility for errors or omissions in this guide The information contained in this manual as well as product design is subject to change without notice Trademarks Initio the Initio logo and the INI prefix are registered trademarks of Initio Corporation SmartSCSI ISGE and I OHIGHWAY are trademarks of Initio Corporation MS DOS Windows Windows 95 and Windows NT are trademarks or registered trademarks of Microsoft Corporation NetWare is a registered trademark of Novell Inc SCO is a registered trademark of Santa Cruz Operation Inc UNIX is a registered trademark of Unix System Laboratories IBM and OS 2 are registered trademarks of International Business Machines Corporation Intel i386 i486 i486DX2 and Pentium are trademarks of Intel Corporation Other manufacturers product names that appear in this manual are for identification purposes only and are acknowledged to be trademarks or registered trademarks of their respective companies Initio Technical Support If you have ques
4. installation section of this manual Question On boot up the message SCSI BIOS Installed is displayed but my system hangs Answer Verify that the CMOS interrupt structure is set to INTA and the CMOS IRQ level matches the jumper settings on the motherboard Refer to your PC user manual Question On boot up not all the peripherals are scanned and recognized Answer Verify that each of the SCSI devices on the bus has its own distinct SCSI ID number and all peripherals are receiving power Refer to your peripheral manual for informa tion regarding changing SCSI ID s Verify the SCSI Termination is set correctly Make sure the last peripheral on the SCSI bus has termination See the peripheral manual for proper termination information After the above steps are executed if you are still not recognizing all attached peripherals configure the host adapter to operate in an Asynchronous Transfer mode by changing its setting under the SCSI Devices Setup section of the SmartSCSI Setup Utility This feature is discussed thoroughly in the chapter entitled Host Adapter Setup Question On boot up I get a message Missing Operating System displayed The boot drive is greater than gigabyte Answer Verify the DOS SPACE gt 1 GB is enabled in the INI 9XXX SmartSCSI Setup Utility Question Under SCO UnixWare the system displays a panic message or crashes during bootup Answer Reboot the system and verify that the I
5. partitions then the original disk The R r option is used to reserved drive letters at start up in order to facilitate a disk change to a disk with more partitions than the original disk present at boot time The value after the R r option determines how many drive letters will be reserved on a device basis For example if the user specifies a R4 option and there are two removable devices attached to the SCSI bus then a total of eight 8 drive letters will be reserved T t This option is used to specify a Time out value to be used when sending commands to a SCSI drive If a SCSI drive does not respond to a command within the specified time out then the command will be aborted and an appropriate error message will be displayed The time out value is specified in minutes Valid values are 1 9 and D or d The D or d values are used to Disable the time out mechanism If the time out mechanism is disabled then faulty hardware can lock up the system Examples T4 Td TD Tl X x This option is used to exclude particular SCSI drives Excluded SCSI drives are identified by specifying the host adapter target id and lun These values are spereated by acolon Groups of SCSI drives or wild cards can also be identified Below are examples of the different ways SCSI drives can be excluded X0 1 2 This will exclude the drive on Host Adapter 0 with target ID 1 and lun 2 X0 2 This will exclude the drive on Host Adapter 0 with target ID
6. 2 and ANY lun initio E MS DOS Windows 3 1x Driver Installation XO This will exclude ALL drives on Host Adapter 0 SAMPLE CONFIG SYS These samples assume that the user has loaded the Initio drivers in the following directory c iniaspi Config sys DEVICEHIGH c iniaspi aspi9 1 Qu DEVICEHIGH c iniaspi inicd sys R2 Explanation The first line loads the ASPI manager and the second line loads the SCSI disk driver specifying that a minimum of two drive letters be reserved for each MO and removable disk attached to the SCSI bus ASPI Partition amp Format Utility INIFDISK EXE is a DOS ASPI partition and format utility It requires the ASPI910U SYS and INIDISK SYS drivers to be loaded in order for it to function properly INIFDISK EXE is installed by the Initio DOSSETUP or SETUP programs Upon invocation the initial screen will have two windows The top window will list all of the SCSI devices installed in the system The user can highlight a particular device by using the up and down arrow keys The bottom window will display information about the device that is currently highlighted in the top window Inifdisk exe can partition and format any SCSI storage device that is not being controlled by the BIOS this includes SCSI disks magnetic optical drives and removable media devices INIFDISK will display two screens in which the bottom portion will explain all commands possible in the top window initio Microsoft W
7. 4a Conformity is declared by the application of EN 55 9100UW2 1987 Class B CISPR 22 1985 BS 6527 1988 EN50081 1 GENERIC EMISSIONS STANDARD EN50082 1 GENERIC IMMUNITY STANDARD 1 IEC 801 2 1984 1000 4 2 1995 2 IEC 801 3 1984 1000 4 3 1995 3 IEC 801 4 1988 1000 4 4 1995 Production Notes This Initio User s Manual was written edited and produced electronically using Adobe Pagemaker Adobe Photoshop Macromedia Freehand Adobe Streamline and Microsoft Word Text type is ITC Novarese and display type is Universe 55 1992 International Typeface Corpora tion 1993 Linotype Hell AG Corporation All rights reserved All product names that appear in this manual are for identification purposes only and are acknowl edged to be trademarks or registered trademarks of their respective companies initio
8. 9100A Host Adapter will support different head mappings based on the setting of DOS Space gt 1GB option MS DOS OS 2 amp Windows NT Under MS DOS OS 2 amp Windows NT we recommend you enable DOS Space gt 1GB option if your SCSI hard disk has more than GByte capacity SCO UNIX SCO UNIX does not have a 1 GByte barrier Therefore the DOS Space gt 1GB option is not required to be enabled however you must make sure the root file system is located below 1024 cylinders in order to perform the kernel boot routines If the size of the root file system is greater than 1 GByte or the location of root file system is beyond 1 GByte you should enable the DOS Space gt 1GB option SCO UNIX can not support different head mappings for each disk drive under the same host adapter The head mapping will be based on the setting represented by target ID 0 initio Troubleshooting Drives with Multiple Operating Systems It is mandatory that the same head mapping be used across multiple operating systems on one drive However you can use different head mappings on different drives with the exception of SCO UNIX It is recommended that you enable DOS Space gt 1GB option if the capacity of your SCSI hard disk has more than GByte initio A ASPI 15 16 ASPI CD ROM Driver 17 ASPI Disk Driver Command Line Options 19 ASPI Manager 17 ASPI910U 17 Autoexec bat 18 BIOS 15 bus 16 c CD R
9. Boot Device ID This option selects which SCSI device will be the designated boot device for the system The default ID for this option is 0 SCSI Terminators This option is used to set auto termination located on the host adapter card This option is also used to manually control termination on the host adapter The normal setting for this option is auto initio T Host Adapter Setup SCSI Parity Check ON Select this option to enable or disable parity checking on the SCSI bus by the host adapter The default setting for this option is on yes NOTE If this option is set ON be certain that the peripheral SCSI device also has this option turned ON BIOS Setup Enable Host Adapter BIOS This option controls the host adapter usage of SCSI disk I O routines inside the host adapter BIOS By disabling this option you will eliminate the host adapter s ability to utilize boot capabilities in OHIGHWAY Setting this to no will also disable all subsequent features displayed by this on screen panel The default setting will be on Yes BIO SUPPORT for More than Two Drives This option supports two or more disk drives on the SCSI bus for MS DOS 5 0 or later when enabled The optimum device identification ID for multiple drive operation is device ID 0 for a system disk and device ID 1 for the second drive The default setting will be on Yes BIOS Treat Removable Disks as Fixed Disk This option is able to treat removable disks a
10. HAM HAM device driver NETWARE HAMMINI9100 DDI HAM device driver installation file Installation The drivers developed by Initio for NetWare will be installed on the disk drive used for NetWare system initialization It is strongly recommended that the selected procedure be read and understood before continuing with the system configuration or change Please read the instructions carefully New IntraNetWare Installation Drivers for the Initio host adapter may be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 In most cases you will load the drivers during a new installation of NetWare from CD ROM The driver is loaded during the NetWare Server Installation procedure The NetWare installation program will prompt you for the required parameters as the installa tion procedure progresses It is highly recommended that you have a copy of the Novell NetWare Installation and Upgrade Manual for reference 1 At the MS DOS prompt for CD ROM installation change directories to where the installation files are located e g d lt ENTER gt Type INSTALL lt ENTER gt to initialize the installation routine Select installation Language lt ENTER gt Select NetWare Server Installation lt ENTER gt Select product type lt ENTER gt Vi A WN initio 6 7 8 Select installation type lt ENTER gt Enter server name when prompted lt ENTER gt At this point the boot files will be copied to the hard drive After the files are finished be
11. When initial boot screen Black and white screen prior to blue screen shows the message Setup is inspecting your computers hardware configuration press F6 3 A setup screen will appear asking which drivers you wish to use 4 Press the appropriate key to add driver and select other 5 Windows NT will prompt you for a manufacturer s supplied disk 6 Insert the Initio manager set floppy marked INI 9XXXU 9XXXUW DRIVER DISK 1 and press ENTER The host adapter should be recognized by Windows NT and the driver will be allowed to load The operating system will continue loading and should recognize the hard drives initio Overview I OHIGHWAY will support Novell NetWare 386 V4 XX or V3 1X with the addition of a software driver The installation procedure described here requires some experience in Novell system setup and administration The device driver is transferred from the INI 9XXXU 9XXXUW DRIVER DISK 1 to the hard drive where it is automatically initialized during the system boot routine The device drivers listed can support NetWare versions described after the Initio file name NETWARE W31X INI910U DSK Initio Novell adapter driver for V3 1X NETWARE V31X ASPITRAN DSK ASPI transport layer driver for V3 1X NETWARE 4X INI910U DSK Initio Novell adapter driver for V4 X or later NETWARE V4X INI910U DDI Device driver installation file NETWARE V4X ASPITRAN DSK ASPI transport layer driver for V4 X or later NETWARE HAM INI9100
12. developed by Initio will be installed on the disk drive used for sys tem initialization It is strongly suggested that the selected procedure be read and under stood before continuing with the system configuration or change Please read the instruc tions carefully Updating interrupts and hardware settings The following interrupt configuration settings are suggested as the most effective means of providing a controller interrupt to the host adapter e Host Adapter interrupt levels available are 9 11 15 IRQ 11 is recommended e Avoid using interrupt 10 as the controller interrupt e Set first SCSI disk ID to 0 first time install requirement e Set tape target ID to 2 If tape is in use e Set CD ROM target ID to 5 If CD ROM is in use Please Refer to your system documentation to set the interrupt levels and your peripheral documentation for help in setting SCSI IDs initio Installing the Initio driver in a new SCO UNIX system 1 Insert the SCO UNIX N1 boot disk into the floppy drive and turn on the system At the SCO UNIX boot prompt type link lt ENTER gt 2 The system will ask you what packages you want linked to the system type i91u lt ENTER gt The system at this point will boot into SCO UNIX Please refer to the SCO UNIX Documentation for additional information When prompted by the installation insert the INI 9XXXU 9XXXUW DRIVER DISK 2 diskette into your floppy drive Press lt ENTER gt 3 Please refer
13. your system to activate the SCSI device driver It is highly recommended that you verify Initio s Windows 95 device driver by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed initio CG Microsoft Windows 95 95b OSR2 Driver Installation Updating the Initio Windows 95 95a Device Driver 1 Once a Windows 95 session is established use your installed mouse or the appropri ate key strokes to select MY COMPUTER from the Main Desktop Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group e Select SYSTEM from within the CONTROL PANEL group 2 e Select the DEVICE MANAGER tab from within the SYSTEM group e Select the SCSI CONTROLLERS category from within the DEVICE MANAGER listing e Select one of the Initio INI 9XXXU UW PCI SCSI Host Adapter sub categories from within the SCSI CONTROLLERS listing or select any other INI 9100U UW class of drivers if you are using an older Initio board e In the INI 9XXX SCSI HOST ADAPTER PROPERTIES window select the DRIVER tab then select CHANGE DRIVER
14. DRIVER DISK 1 It is important that the hardware has been installed successfully before proceeding further 1 Execute a floppyless setup as described by the Windows NT System Administrator s Guide initio E Microsoft Windows NT Driver Installation 2 When SETUP begins to load the screen will turn from black to blue with the text SETUP IS INSPECTING YOUR COMPUTER S HARDWARE CONFIGURATION at the top e Press the F6 key to interrupt this process You will have two seconds in which to press this key e Follow the instructions on the screen until you are asked to specify a SCSI driver 3 Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into your local floppy disk drive and press lt ENTER gt e Select Initio INI 9XXXU UW PCI SCSI Host Adapter 4 The Initio host adapter driver is now installed The on screen instructions will continue for a complete installation of Windows NT Refer to your Windows NT System Administrator s Guide for completion of the operating system installation procedure Installing a new Windows NT system from a Bootable CD For computer systems installing or upgrading to Windows NT from a bootable CD these instructions will guide you through the INI 9XXXU 9XXXUW host adapter driver installa tion The Windows NT driver will be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 It is important that the hardware has been installed successfully before proceeding further 1 Boot your system from a Windows NT CD 2
15. HAM modify the STRATUP NCF file to reflect the new changes initio Upgrading Changing Driver on an Existing IntraNetWare Server 10 11 12 n To begin the you will need to change the directory to the location of the server and initialize the network server e g Type CD NWSERVER lt ENTER gt Type SERVER lt ENTER gt At the NetWare prompt Type LOAD INSTALL lt ENTER gt Select Driver Options from the window by highlighting it using the UP or DOWN ARROW keys press lt ENTER gt e Select Configure disk and storage device drivers from the window by high lighting it using the UP or DOWN ARROW keys press lt ENTER gt Highlight Deselect a selected driver and press lt ENTER gt Highlight the driver you wish to replace upgrade and press lt ENTER gt Repeat steps 4 and 5 for each instance of the driver When all of the drivers you wish to upgrade replace have been removed highlight Select an additional driver and press lt ENTER gt Press lt INS gt followed by lt F3 gt Enter the location path of the drivers A Select the driver you wish to load INI9100 HAM or INI910U DSK and press lt ENTER gt If the HAM driver s are being used proceed to step 10 If you use the DSK driver the upgrade is complete and you may exit the install utility Highlight Select and modify parameters and press lt ENTER gt Enter the slot number and press lt F10 gt to continue Highlight Save parameters and continue and press
16. NI 9100A is using IRO10 Please Refer to your system documentation to set the interrupt levels and your peripheral docu mentation for help in setting SCSI ID s In order to boot from the old UnixWare kernel reboot the system and execute the following steps Begin an interactive boot session by pressing the lt SPACEBAR gt at the BOOTING UNIXWARE prompt e At the system boot prompt type KERNEL unix org lt ENTER gt e Type go lt ENTER gt initio C2 Troubleshooting Consult the SCO UnixWare Installation Handbook Troubleshooting section to help isolate the problem If it becomes necessary to remove the Initio device driver please consult the Removing the Initio Driver from a SCO UnixWare System section of this document B DOS Space gt 1GB The default disk head mapping for Initio SCSI host adapter is 255 heads and 63 sectors This translates to a maximum accessible capacity of 8 GBytes per drive under MS DOS Warning If you have already installed the operating system on your hard drives changing the head mapping will corrupt your files and cause other unexpected prob lems Before changing any DOS Space gt 1GB option setting please back up your disk drives Then you should run the FDISK utility to delete all the partitions on your selected disk drive At this point you can switch the setting reinstall the operating system and restore your backed up files All device drivers for the INI
17. OM 18 CONFIG SYS 16 CONTROL PANEL 22 24 27 31 D DEVICE MANAGER 23 24 28 DEVICEHIGH command 19 Disk Access 16 DOS 15 DOS 4 01 21 DOS ASPI 16 DOSSETUP 15 DSK drivers 34 35 F File Manager 22 H HAM driver 34 35 HAVE DISK 24 Host Adapter Driver 23 1910u 46 i910u ihv hba 46 INI9100 HAM 34 ini910U DSK 34 INISTOU INF 21 INI910U MPD 21 23 27 28 INI910U SYS 29 INICD SYS 17 INICDO01 18 Inidisk sys 19 INIFDISK ASPI Partition amp Format Utility 20 INIFDISK EXE 20 Integrated Scatter Gather Engine 3 IRQ 45 K KRNL32 DLL 21 L Load Pathname ini910u 36 M MO 19 MS DOS 16 33 MSCDEX EXE 17 NetWare 33 34 NEW HARDWARE FOUND 23 Novell 33 Novell NetWare 33 34 initio O OEMSETUPINF 29 OS 2 driver 37 OSR2 21 25 26 P PCI SCSI BUS CONTROLLERS 23 PCI SCSI Bus Controller 22 PROGRAM MANAGER 16 R README TXT 16 S SCO UNIX 41 SCO UNIXWARE 45 SCO UnixWare 45 SCSI CONTROLLER 23 31 SCSI CONTROLLERS 28 SCSI IDs 45 SETUPEXE 22 SYSTEM INI 16 T TXTSETUPOEM 29 U UnixWare 47 UPDATE DRIVER 28 w Windows 3 x 25 Windows 95B 25 26 WINDOWS NT WORKSTATION SETUP 30 Windows NT 29 Windows NT 4 0 29 initio Product Warranty Initio Corporation warrants to the original purchaser that this product shall be free from defects in material and workmanship for a period of 5 years from the date of purchase Should this product in the judgment of Initio Co
18. README file from the MS DOS prompt type the following command from the MS DOS prompt C gt type readme txt more This will permit you to page down the file one screen at a time to read the file P C D119 03 May 1998 Third Edition rinhnitio Technical Support ii 1 INTRODUCTION 1 The Initio I OHIGHWAY PCI FastSCSI host adapter 1 Technical Illustration 2 Product Features Specifications 3 2 GETTING STARTED 5 Host adapter andthe SCSI bus 5 SCSI bus preparation 5 SCSI bus termination 5 3 HARDWARE INSTALLATION 7 nstallation basics 7 nstallation in ten easy steps 7 Hard disk drive preparation 11 Low level format 11 4 HOST ADAPTER SETUP 13 Running the SmartSCSI Setup Utility 13 Main Menu Options 13 5 MS DOS WINDOWS 3 1X DRIVER INSTALLATION 17 Overview 17 Installing the Initio ASPI driver to an existing MS DOS system 17 Installing the Initio ASPI driver to an existing Win3 1x system 18 ASPI Manager command line options 19 ASPI CD ROM Driver Command Line options 19 ASPI Disk Driver Command Line options 21 ASPI Partition and Format Utility 22 6 MICROSOFT WINDOWS 95 95B OSR2 DRIVER INSTALLATION 23 Overview 23 Installation 23 New Windows 95 95a installation 23 Adding the Initio Driver to an existing Windows 95 95a system 25 Updating the Initio 95 95a device driver 26 New Windows 95b OSR2 installation 27 Adding the Initio driver to an existing Windows 95B ORS2 System 28 Updating the Initio 95B OSR2 device driv
19. VICEHIGH c iniaspi inicd sys D INICD001 Explanation The first line loads the ASPI manager and the second line loads the CDROM driver specifying the device name INICDO01 Autoexec bat Mscdex D INICD001 Explanation This line will load the Microsoft supplied mscdex exe file instructing it to attach to the CD ROM device driver INICDOO1 initio lt MS DOS Windows 3 1x Driver Installation ASPI Disk Driver Command Line Options INIDISK SYS is a DOS block device driver for supporting SCSI fixed disks removable disks and MO devices INIDISK SYS is automatically loaded in CONFIG SYS start up file by the Initio DOSSETUP or SETUP programs INIDISK SYS requires that the Initio ASPI Manager be loaded INIDISK SYS can be loaded with either the DEVICE or DEVICEHIGH command INICD SYS can be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 Below is a list of command line options and examples R r This option specifies the number of logical drives to reserve for MO and removable disk devices MO and removable disks media are capable of being parti tioned just like a fixed disk For every DOS partition on the media a logical DOS drive letter will be available INIDISK SYS will support as many logical drives as required up to the maximum supported by DOS based on the partitioning of the media that is present when your system boots However the media may be removed at any time and a new disk may be inserted The new disk may have more or less
20. al chassis rail after you have turned off the power initio CCS Hardware Installation 3 Inserting the host adapter Orient the host adapter for installation so that the external connector is facing the back of the system unit and align the card with the PCI connector on the system unit See FIGURE 3 Holding the adapter by the mounting bracket and the card edge match up the card edge connector with the PCI host computer socket and insert the card into the socket Once the connector is in the PCI expansion slot socket tighten the mounting bracket screw to secure the card in place lige ee i FIGURE 3 Inserting the host adapter into a PCI slot 4a Installation of internal SCSI cables The number of internal and external connectors for Initio s SCSI host adapters are referenced in the hardware installation section TABLE 2 All internal connectors may be used simultaneously or singularly depending on your bus configuration Installation of internal SCSI cables must be performed before replacing the system covers The internal ribbon cable is made with multiple connectors attached and used to daisy chain the host adapter with two or more devices Itis important that the cable be installed correctly for proper operation The cable has a colored stripe running the length of the cable on the edge distin guishing the pin one side of the connector These identifying markings must match when mated on the host adapter boar
21. and SCO UnixWare System Owner Handbook for reference 1 Insert the SCO UNIXWARE INSTALLATION DISKETTE into the floppy drive and turn on the computer Follow the on screen installation instructions initio 2 When prompted to INSTALL HOST BUS ADAPTER DRIVERS insert the INI 9XXXU 9XXXUW DRIVER DISK 2 into drive A press lt Enter gt When prompted to INSTALL ANOTHER HBA DISKETTE press lt ENTER gt to con tinue Follow the directions on screen until you come to a window titled Loading Initio INI 9XXX Host Adapter e Select CONTINUE INSTALLATION e Select CONTINUE INSTALLATION again This completes loading the host adapter driver Follow the on screen directions to complete the SCO UnixWare installation For further information regarding UnixWare installation refer to the SCO UnixWare Installation Handbook Adding the Initio driver to an existing UnixWare system I 2 3 Once a UnixWare session is established and a command prompt is ready type recall that UnixWare is case sensitive e cp stand unix stand unix org press lt ENTER gt e pkgadd d diskettel press lt ENTER gt Select i910u ihv hba from the list of available host drivers press lt ENTER gt If the INI 9XXxX is intended to be the bootable host adapter the next step to updating the driver will require a revision to the 1910u file These instructions will guide you through changing the current software settings for UnixWare to establis
22. as a specific device ID commonly referred to as a SCSI ID Please refer to your peripheral documentation to determine switch or jumper settings for SCSI ID s No two devices can have the same ID the device ID uniquely defines the device to the SCSI bus SCSI bus termination The SCSI bus structure has a length limitation as well as a requirement for termination at each end of the SCSI cable The cable is designed to connect in a daisy chain fashion No branching is permitted in the SCSI bus The first and last physical SCSI device on the SCSI bus must be terminated FIGURE 2 TERMINATION NO TERMINATION TERMINATION FIGURE 2 Examples of SCSI bus termination initio E Getting Started I OHIGHWAY s SCSI termination can be set to auto termination or programmable mode via the SmartSCSI Setup Utility This feature allows the operator to switch the auto termination On or Off If auto termination is switched off the operator can manually program termination for the host adapter There are three ways to manually control terminating the host adapter on the SCSI bus see TABLE 1 SCSI Devices Configuration SCSI Channel Termination Internal Devices Only i 1 interval amp External Devices TABLE 1 I OHIGHWAY possible termination settings Assumption Host adapter is at the end of the SCSI bus Assumption Host adapter is in the middle of the SCSI bus initio Installation Basics The internal cabl
23. ave distinct differences It is strongly suggested that the selected procedure be read and understood before proceed ing with the system configuration changes Please read the instructions carefully New Windows NT Installation These instructions will guide you through the installation of the Initio host adapter driver while installing Windows NT 4 0 Windows NT will be installed from either floppy diskettes or CD ROM The Windows NT driver is located on the INI 9XXXU 9XXXUW DRIVER DISK 1 It is important that the hardware has been installed successfully before proceeding further 1 If you are installing Windows NT from floppy diskettes locate the Windows NT Disk 1 for Floppy Installation Make a backup copy of this diskette before installation initio E Microsoft Windows NT Driver Installation 2 If you are installing Windows NT from a CD version locate the Windows NT Setup Disk for CD ROM Installation Make a backup copy of this diskette before installation 3 Insert the backup Windows NT Setup disk into drive A and turn on your com puter 4 Follow the instructions on the screen until you come to a window titled WINDOWS NT WORKSTATION SETUP for servers it will read WINDOWS NT SERVER SETUP e Press ENTER to continue setting up Windows NT e Select S to skip mass storage detection e Select S to configure additional SCSI adapters 5 When prompted by the Windows NT installation scroll down t
24. cond field at CONF SDEVICE D 1910U for each INI 9XXX ion to set the interrupt levels figured and allocated by a separate line in the line starting at I9 1 Ou in the file ETC in the system UnixWare will automatically rebuild the kernel when an additional INI 9XXX is detected Removing the Initio driver from a UnixWare system 1 Once a UnixWare session is established and a comm is case sensitive and prompt is ready type recall that UnixWare e Type etc conf bin idinstall d i910u lt ENTER gt to delete the following files etc conf mdevice d i9 10u etc conf sdevice d i9 10u etc conf pack d i9 1 Ou driver o etc conf pack d i9 1 Ou space c etc conf pack d i9 1 Ou disk cfg etc conf pack d i9 1 Ou disk cfg initio 2 Then rebuild the UnixWare kernel by executing the following commands at the system prompt etc conf bin idbiuld B K lt ENTER gt cp etc conf cf d unix stand unix lt ENTER gt cd lt ENTER gt shutdown g0 where 0 is Zero lt ENTER gt Y lt ENTER gt initio lt Troubleshooting In the following section you will find commonly asked questions and answers to problems encountered during the installation of your host adapter Question Why isn t the INI 9XXX banner Press lt CRTL gt lt I gt for SmartSCSI Setup Utility 1 displayed when I power up the host system Answer Verify that all cabling to the host adapter is installed correctly refer to the hardware
25. d initio 4b When attaching FastSCSI devices use the 50 pin FastSCSI cable connector on the host adapter Align the internal cable into the host adapter and the other cable connectors in a similar fashion into the other SCSI device connectors as described in the appropriate manufacturers instructions BS FIGURE 4 Connecting the 50 pin internal flat ribbon cable Installation of external SCSI cables Installation of external SCSI cables can be performed after the cover has been closed The cable is limited in length to a total of six meters including any internal cabling The external cable can be daisy chained to include up to seven with the host adapter in combination with internal devices The external cable is designed to be inserted only one way requiring termination at the end peripheral device on the bus FIGURE 5 Terminating Plug FIGURE 5 External cable connection initio CCH Hardware Installation 5 Drive activity LED A drive activity LED is designed into the host adapter to indicate when a data transfer is being made Connection to the LED is optional and cabling is not in cluded with this kit Each host adapter has one four pin connector Please refer to the host adapter s illustration FIGURE 1 for the LED connector that will accomodate the LED cable 6 Multiple Initiators Under some circumstances multiple initiators can be used on a single SCSI bus The bus i
26. e In the SELECT DEVICE window select HAVE DISK 3 In the INSTALL FROM DISK window enter the Initio Driver path name e Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into drive A e Type A WIN95 select OK 4 Select Initio INI 9XXXU UW PCI SCSI Host Adapter select OK to install the INI910U MPD driver onto your hard disk drive It may be necessary to direct Windows to look for the driver in A win95 before the driver can be copied This step may need to be repeated more than once This completes updating the Host Adapter Driver Follow the on screen directions to restart you computer and activate the new driver It is highly recommended that you verify Initio s Windows 95 device driver by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed initio Microsoft Windows 95 95b OSR2 Driver Installation New Windows 95B OSR2 Installation These instructions will guide you through the installation of the Initio host adapter driver while installing Windows 95B OSR2 Windows 95B will be installed from either a CD ROM or
27. e installation drive and directory that the ASPI driver will be installed on Follow the on screen directions and or options to continue the installa tion 6 To activate the device driver reboot the system by selecting the Reboot Now option at the end of the installation process initio Ct MS DOS Windows 3 1x Driver Installation Installing the Initio ASPI drivers to an existing Windows 3 1x system The ASPI for Windows 3 1x drivers are found on the INI 9XXXU 9XXXUW DVR DSK 1 It is important that the SCSI bus hardware and operating system are installed correctly before proceeding further If you need help installing Windows 3 1x please refer to the Microsoft Windows manual before proceeding 1 Turn on host system and boot into MS DOS and Windows 3 1x operating system 2 Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into your floppy drive 3 Use your installed mouse or the appropriate key strokes to select RUN from the Windows PROGRAM MANAGER Execute the following steps e Type A SETUP lt ENTER gt A series of screens will guide you through the installation of the ASPI for Windows device drivers e Choose CONTINUE to continue the installation sequence e Choose CONTINUE to accept the Host Adapter selection 4 Two installation options are available e Choose EXPRESS INSTALL to install both the DOS ASPI drivers and the Windows 32 bit Disk Access drivers Use this option if you are unfamiliar with configuring a DOS or Windo
28. e located in your Windows directory A file date of 07 11 95 belongs to Windows 95 first release 12 31 95 belongs to Win dows 95a or 95 with Service Pack 1 and 08 24 96 reflects Windows 95b or OSR2 New Windows 95 95a Installation These instructions will guide you through the installation of the Initio host adapter driver while installing Windows 95 Windows 95 will be installed from either a CD ROM or floppy diskettes It is important that the hardware and DOS 4 01 or higher have been installed successfully before proceeding further If installing from a SCSI CD ROM drive it is impor tant that the Initio ASPI driver and CD ROM driver be installed before proceeding further initio E Microsoft Windows 95 95b OSR2 Driver Installation 1 Access the Windows 95 CD ROM from either the DOS prompt or from Microsoft Windows 3 x File Manager Execute the SETUPEXE program and follow the instruc tions on your screen If you are installing from floppy diskette insert the Windows 95 Setup Disk in your floppy disk drive and boot your system Follow the instructions on your screen 2 Once a Windows 95 session is established use your installed mouse or the appropri ate key strokes to select MY COMPUTER from the MAIN DESKTOP Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER icon e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER tab from within the SYSTEM group e Select t
29. e permits connection of multiple internal devices SCSI devices that are connected to the internal connector are installed inside the host computer enclosure The external connector is accesible through the D shell connector at the back of the host system and is designed to connect devices outside the host system enclosure The following table has connector details of I OHIGHWAY Internal External Maximum SCSI Connector Connector Devices allowed VOHIGHWAY S D Standard Density EREFEERCEERECEEFEErEECeer H D High Density PEIEE APOE al FFETFTFITErErIIrrIrIrTT Jo TABLE 2 Connector Details To increase the reliability of the cabling being used with the host adapter it is recom mended that the following guidelines be observed e SCSI 1 up to 6 meters or 20 feet e FastSCSI up to 6 meters or 20 feet e Impedance of the cable should be between 90 110 ohms e Use high quality shielded connectors Installation in Ten Easy Steps 1 Power down the host computer and all peripherals Remove the cover from the host system You may need to refer to the system manual for cover removal If necessary identify the PCI sockets inside the host system with the aid of the system documentation 2 Use static electricity discharge precautions Remove possible static discharge potential from any objects that the host adapter may come in contact with before installation This can be accomplished by touching a bare met
30. ed to be changed Under some condi tions the system will expect the boot disk to be an IDE drive This must be changed in order to boot from a SCSI device initio 9 System startup The newly installed SCSI bus is now ready to power up Switch on peripheral and host computer system power The system monitor should display the following information but may vary based on the system BIOS manufacturer e The normal Power On Self Test and memory test procedure e The host adapter sign on message including a list of attached SCSI devices The list should match the peripheral devices attached to the bus In most cases the host computer system is now configured and ready for use Some situations will require that a low level format be performed using the host adapter SmartSCSI Setup Utility to initialize a SCSI disk drive and lay the foundation for a bootable SCSI drive 10 SmartSCSI Setup Utility The SmartSCSI Setup Utility simplifies the SCSI installation process by eliminating the need for opening the system to change system jumpers and switch settings All necessary host adapter functions are accessible through the utility simplifying customization for your system needs Initio s SmartSCSI Setup Utility is divided into five segments identified by Scan Bus Device Setup Adapter Setup BIOS Setup and Disk Utility These program functions are accessible by typing lt CTRL gt lt I gt at the boot up prompt Hard Disk Drive Prepara
31. er 29 initio 7 MICROSOFT WINDOWS NT DRIVER INSTALLATION 31 Overview 31 Installation 31 New Windows NT installation 31 Adding or updating the Initio driver to an existing WinNT system 33 Installing a new WinNT system and Initio driver w out floppy disks 34 8 NOVELL NETWARE DRIVER INSTALLATION 35 Overview 35 Installation 35 New NetWare 4 xx installation 35 Adding the Initio driver to an existing NetWare system 36 Device driver command line options 37 9 IBM OS 2 DRIVER INSTALLATION 39 Overview 39 Installation 39 New OS 2 installation 39 Adding the Initio driver to an existing OS 2 system 40 Device driver command line options 40 10 SCO UNIX DRIVER INSTALLATION 43 Overview 43 Installation 43 Updating interrupts and hardware settings 43 Installing the Initio driver ina new SCO UNIX system 44 Adding the Initio driver to an existing SCO UNIX system 44 Changing to the INI 9XXX as the bootable host adapter 45 11 SCO UNIXWARE DRIVER INSTALLATION 47 Overview 47 Installation 47 Updating interrupts and hardware settings 47 Installing the Initio driver in a new UnixWare system 47 Adding the Initio driver to an existing UnixWare system 48 Using Multiple Host Adapters 49 Removing the Initio driver from a UnixWare system 49 TROUBLESHOOTING 51 55 PRODUCT WARRANTY 57 initio The Initio I O HIGHWAY Host Adapter The Initio OHIGHWAY is a high performance PCI bus master FastSCSI host adap
32. evice is working properly is displayed on your screen the driver has been correctly installed initio Microsoft Windows 95 95b OSR2 Driver Installation Adding the Initio Driver to an Existing Windows 95 95a System These instructions will guide you through the installation of the Initio host adapter to an existing Windows 95 system Windows 95 will automatically detect the presence of new hardware in Plug and Play compliant systems It is important that the Initio hardware has been properly installed before proceeding further N vi Microsoft Windows 95 will detect the presence of new hardware upon boot up and will display a dialog window titled NEW HARDWARE FOUND and PCI SCSI BUS CONTROLLERS will be highlighted e Select DRIVER FROM DISK PROVIDED BY HARDWARE MANUFACTURER then OR e Select SCSI CONTROLLER from the list of available devices then select HAVE DISK In the INSTALL FROM DISK window that is displayed enter the Initio Driver path name Insert INI 9XXXU 9XXXUW DRIVER DISK 1 into drive A Type A WIN95 select OK Select Initio INI 9XXXU UW PCI SCSI Host Adapter select OK then OK again to install the INI910U MPD driver onto your hard disk drive It may be necessary to direct Windows to look for the driver in A win95 before the driver can be copied This step may need to be repeated more than once This completes loading the Host Adapter Driver You must now reboot
33. floppy diskettes It is important that the hardware and DOS 4 01 or higher have been installed successfully before proceeding further If installing from a SCSI CD ROM drive it is important that the Initio ASPI driver and CD ROM driver be installed before proceeding further I Access the Windows 95B CD ROM either from the DOS prompt or from Microsoft Win dows 3 x File Manager Execute the SETUPEXE program and follow the instructions on your screen If you are installing from floppy diskette insert the Windows 95 Setup Disk 1 in your floppy disk drive and boot your system Follow the instructions on your screen Once a Windows 95 session is established use your installed mouse or the appropri ate key strokes to select MY COMPUTER from the MAIN DESKTOP Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER tab from within the SYSTEM group e Select the OTHER DEVICES category from within the DEVICE MANAGER listing e Select one of the PCI SCSI Bus Controller sub category from within the OTHER DEVICES listing e In the Initio PCI SCSI Bus Controller Properties window select the DRIVER tab then select UPDATE DRIVER e Insert INI 9XXXU 9XXXUW DRIVER DISK 1 into drive A e Select YES click Next and Windows will search for the driver e Select the OTHER LOCATION e Type A WINY5 then select OK e Select FINISH
34. h Valid characters are the A Z a z 0 9 and underscore The name must start with a letter Examples D INICDO01 d mscd001 d MYCDO1 T t This option is used to specify a Time out value to be used when sending commands to a CDROM drive If a CDROM drive does not respond to a command within the specified time out then the command will be aborted and an appropriate error message will be displayed The time out value is specified in minutes Valid values initio E MS DOS Windows 3 1x Driver Installation are 1 9 and D or d The D or d values are used to Disable the time out mechanism If the time out mechanism is disabled then faulty hardware can lock up the system Examples T4 Td TD Tl X x This option is used to exclude particular CD ROM drives Excluded CDROM drives are identified by specifying the host adapter target id and lun These values are spereated by a colon Groups of CDROM drives or wild cards can also be identified Below are examples of the different ways CDROM drives can be excluded X0 1 2 This will exclude the drive on Host Adapter 0 with target ID 1 and lun 2 X0 2 This will exclude the drive on Host Adapter 0 with target ID 2 and ANY lun XO This will exclude ALL drives on Host Adapter 0 SAMPLE CONFIG SYS AND AUTOEXEC BAT FILES These samples assume that the user has loaded the Initio drivers in the following directory c iniaspi Config sys DEVICEHIGH c iniaspi aspi9 1 Ou DE
35. h the INI 9XXX as the host adapter for your boot device e At the system command prompt type e cd etc conf sdevice d e Use vi or another editor to modify the file 1910u by adding a line e locate the line Sversion2 e edit the file by adding the line static immediately following Sversion2 e Rebuild the UnixWare kernel by completing the following steps at the command prompt e etc conf bin idbuild B lt ENTER gt e cp etc conf cf d unix stand unix lt ENTER gt e cd lt ENTER gt shutdown g0 0 is Zero lt ENTER gt e Y lt ENTER gt initio 4 If the host adapter is NOT intended to be bootable these instructions will guide you through changing the current software settings for UnixWare to establish the INI 9XXX as a non bootable host adapter for your device e At the system command prompt type e etc conf bin idbuild M i910u lt ENTER gt e cd lt ENTER gt shutdown g0 0 is Zero e Y lt ENTER gt lt ENTER gt 5 Exit the UnixWare program and reboot your system to initialize the new device driver to control INI 9XXX Using Multiple Host Adapters UnixWare is capable of supporting up to eight SCSI busses If you choose to use multiple host adapters in your system verify that each host adapter shared interrupt level is set to IRQ10 Please refer to your system documentat Space for each host adapter in the system is con the file ETC CONF SDEVICE D 19 1 0U 1 Verify that Yis selected in the se
36. he OTHER DEVICES category from within the DEVICE MANAGER listing e Select the PCI SCSI Bus Controller sub category from within the OTHER DE VICES listing e In the Initio PCI SCSI Bus Controller Properties window select the DRIVER tab then select CHANGE DRIVER e In the SELECT HARDWARE TYPE window select SCSI CONTROLLERS e In the SELECT DEVICE window select HAVE DISK 3 In the INSTALL FROM DISK window enter the Initio Driver path name e Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into drive A Type A WINY5 select OK 4 Select Initio INI 9XXXU UW PCI SCSI Host Adapter select OK then OK again to install the INI910U MPD driver onto your hard disk drive It may be necessary to direct Windows to look for the driver in A win95 before the driver can be copied This step may need to be repeated more than once 5 Following installation of the Initio INI 9XXXU UW Windows 95 driver for all channels reboot your system to activate the SCSI device driver 6 Itis highly recommended that you Initio s Windows 95 device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select Initio INI 9XXXU UW PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This d
37. he list and select OTHER Requires disk provided by a hardware manufacturer from the list of Additional SCSI Adapters A message will appear on screen stating to e Remove diskette in drive A and set it aside e Insert INI 9XXXU 9XXXUW DRIVER DISK 1 and press lt ENTER gt e Select Initio INI 9XXX SCSI Host Adapter and press lt ENTER gt 6 The Initio host adapter driver is now installed The on screen instructions will continue for a complete installation of Windows NT Refer to your Windows NT users manual for completion of the operating system installation procedure Adding or updating the Initio driver to an existing Win dows NT system For computer systems using other SCSI host adapters or an IDE drive to provide the system boot routine these instructions will guide you through the INI 9XXX host adapter driver installation The Windows NT driver will be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 It is important that the SCSI bus hardware and Windows NT are installed and configured before proceeding further 1 Once a Windows NT session is established use your installed mouse or the appropri ate key strokes to select MY COMPUTER from the Main Desktop Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group e Select SCSI ADAPTERS from within the CONTROL PANEL group 2 Select the DRIVERS tab from within the SCSI ADAPTERS group e In the DRIVERS window select ADD initio Micr
38. indows 95 95b OSR2 Driver Installation Overview I OHIGHWAY will support Microsoft Windows 95 and Windows 95B OSR2 with the addition of a software driver The installation procedure described here requires some experience in Windows 95 system setup and administration The device driver is transferred from the INI 9XXXU 9XXXUW DRIVER DISK 1 to the hard drive where it is automatically initialized during the system boot routine The following files are used for installation and will be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 WIN95 INI9 10U MPD INI 9XXX SCSI Host Adapter Windows 95 miniport driver WIN95 INI910U INF Windows 95 installation information file Installation The INI 9XXX driver developed for Windows 95 is loaded during the system boot routine and will remain resident on the drive This is accomplished by following one of the three installation procedures listed e New Windows 95 and Windows 95B OSR2 installation e Adding the Initio Windows 95 device driver to an existing Windows 95 or Windows 95B OSR2 system Updating INI910U MPD device driver The procedures described to make changes to the system have distinct differences It is strongly suggested that the selected procedure be read and understood before proceed ing with the system configuration changes Please read the instructions carefully To determine which version of Windows 95 you have installed on your system check the date of the KRNL32 DLL fil
39. ine switches is Device C INIASPI ASPI9 1 0U SYS Driver Config Option D Verbose Mode provides detailed information about the driver on system com mand line when the driver is initialized I Driver scan eight LUNs for each SCSI Target Bb dd Scan device only on PCI BUS b PCI DEVICE dd The range for b is from 0 to 7 The range for dd is from 0 to 20 Bb Scan all the devices on the PCI BUS b The range for b is from 0 to 7 Sdd Scan device only on the PCI BUS 0 and device dd The range for dd is from 0 to 20 CCBSx Defines the maximum number of concurrent I O that driver supports The range for x is from 1 to 16 ASPI CD ROM Driver Command Line Options INICD SYS is a DOS device driver for supporting SCSI CD ROM drives It is the interface between MSCDEX EXE supplied by Microsoft and the physical CDROM drive INICD SYS is automatically loaded in the CONFIG SYS start up file by the Initio DOSSETUP or SETUP programs INICD SYS requires that the Initio ASPI Manager be loaded INICD SYS can be loaded with either the DEVICE or DEVICEHIGH command INICD SYS can be found on INI 9XXXU 9XXXUW DRIVER DISK 1 Below is a list of command line options and examples D d This option is used to specify the name of the device driver The name specified must also be passed to MSCDEX EXE on it s command line Using the same D or d option The name specified must be 8 or less characters in lengt
40. information about driver on system command line when driver is initialized Non Verbose Mode default Driver assumes that all targets have more than one LUN Driver assumes that all targets only have LUN 0 default Target enable mask WORD Default scan all targets in hex format Scan device only on PCI BUS b DEVICE dd in decimal format Scan all the devices on PCI BUS b from 0 to 7 Assigns adapter number based on BIOS address Enable direct access storage device DASD support Disable DASD manager support Enable SCSI manager support Disable SCSI manager support Specifies maximum number of tag commands per target No tag initio Overview The I OHIGHWAY SCO UNIX device driver will support SCO UNIX System V 386 Release 3 2v4 0 or later SCO Open Desktop v2 0 v3 0 or later and SCO Open Server Release 3 0 amp 5 0 x The device driver is transferred from the floppy diskette to the hard drive where it s loaded during system initialization The installation of Initio device drivers to support SCO UNIX include the following software files and may be found on the INI 9XXXU 9XXXUW DRIVER DISK 2 Driver o Device driver object file Space c Device driver definition file Reference Documentation e SCO UNIX documentation installation and user s guide e The systems setup and installation guide e The documentation for system peripherals e Initio documentation for the SCSI host adapter Installation The SCO UNIX drivers
41. ing copied you may encounter the following message Install found the following hardware but found More than one driver supporting this hardware PCI XXXX XXXX XXXX XXXX XX Press lt Enter gt for a list of drivers to choose From or lt F3 gt to continue without selecting Press lt F3 gt to continue Repeat if this screen is shown again A screen listing the drivers will be displayed INI9100 will be listed as the selected driver This completes loading the Host Adapter Driver Follow the on screen direc tions to complete the Novell NetWare installation This will load the HAM driver If a DSK driver is required or an updated HAM driver is needed it is recommended that you complete the installation and use NetWare s INSTALL utility to update change the driver Adding the Initio driver to an existing IntraNetWare sys tem I A o begin the installation you will need to change the directory to the location of the server and initialize the network server e g Type CD NWSERVER lt ENTER gt Type SERVER lt ENTER gt At the NetWare prompt Type LOAD INSTALL lt ENTER gt Select Driver Options from the window by highlighting it using the UP or DOWN ARROW keys press lt ENTER gt e Select Configure disk and storage device drivers from the window by high lighting it using the UP or DOWN ARROW keys press lt ENTER gt Highlight Discover and load additional drivers and press lt ENTER gt NetWare will load INI9100
42. is transferred from the floppy diskette to the hard drive where it is loaded during system initialization The installation of Initio device drivers to support SCO UnixWare may be found on the INI 9XXXU 9XXXUW DRIVER DISK 2 Installation The SCO UnixWare drivers developed by Initio will be installed on the disk drive used for system initialization It is strongly suggested that the selected procedure be read and understood before continuing with the system configuration or change Please read the instructions carefully Updating interrupts and hardware settings The following interrupt configuration settings are suggested as the most effective means of providing a controller interrupt to the host adapter e Host adapter interrupt level must be set to IRQ 10 for proper installation of the Initio driver Please refer to your system documentation to set the interrupt levels and your periph eral documentation for help in setting SCSI IDs Installing the Initio driver in a new UnixWare system Drivers for the host adapter may be found on the INI 9XXXU 9XXXUW DRIVER DISK 2 In most cases you will load the drivers during a new installation of UnixWare from CD ROM The driver is loaded during the early stages of the installation procedure The UnixWare installation program will prompt you for the required parameters as the installation procedure progresses It is highly recommended that you have a copy of the SCO UnixWare Installation Handbook
43. lt ENTER gt Repeat steps 6 through 11 for each additional adapter installed initio Device driver command line options The Initio device drivers support command line switches to optimize driver performance However in certain situations some driver optimization may be advantageous to system performance NetWare offers two means of entering command line switches One method is for session usage and needs to be entered each time the system is rebooted Load Pathname ini910u Driver Config Option The second method listed is for permanent installation In startup ncf you can include the following statement Load Pathname ini910u Driver Config Option or Load Pathname INI9100 Driver Config Option Driver Config Options N Verbose Mode provides detail information about driver on system command line when driver is initialized WV Non Verbose Mode default IL Driver assumes that all targets have more than one LUN AL Driver assumes that all targets only have LUN 0 default T XXxx Target enable mask WORD Default scan all targets B b dd Scan device only on PCI BUS b PCI DEVICE dd B b Scan all the devices on PCI BUS b from 0 to 7 O q Specifies maximum number of tag commands per target default 4 NO No tag WR Read after write hardware verify IWR Not verified default R Support removable media default IR Will not support removable media D Enable support for fixed disk drive default
44. n Menu Options SmartSCSlI s main menu provides five possible setup options for meeting your system configuration Scan Bus Device Setup Adapter Setup BIOS Setup Disk Utility Scan Bus This option scans the SCSI bus All device ID s are displayed on the screen including SCSI ID s without devices attached This allows for a better definition of location and priority on the SCSI bus e A device ID should only be changed if it conflicts with another device address on the same bus Refer to your peripheral documentation for changing SCSI ID s e The best ID for a bootable hard disk is SCSI ID Device Setup Asynchronous Transfer Use this option to set the synchronous data transfer mode OHIGHWAY will transfer data at a maximum rate of 10 MBytes per second in synchro nous mode and a maximum rate of 5 Mbytes per second in asynchronous mode Use this option to set the synchronous data transfer mode The default setting for this option is for synchronous operation no Maximum Synchronous Transfer Rate This option determines the speed at which data is moved across the SCSI cable I OHIGHWAY has the option of running up to 10 MBytes per second initio es Host Adapter Setup DOS Space gt 1 GB Using this option allows for single disk capacities to be extended up to 8 GBytes yes Please refer to the Appendix titled DOS Space gt 1 GB for further information on this feature e NO DOS limits the number of cylinde
45. nd MO drivers Installation The installation procedure guides you through the installation of the Initio DOS ASPI and the ASPI for Windows 3 1x drivers The installation procedure described here requires some experience in MS DOS or Windows 3 1x system setup and administration The device driver is transferred from the INI 9XXXU 9XXXUW DRIVER DISK 1 to the hard drive where it is automatically initialized during the system boot routine The INI 9XXXU 9XXXUW DRIVER DISK 1 contains two installation programs that perform the same task If you have completed installing the Initio ASPI driver using the MS DOS based installation routine described in this User s Manual it is not necessary to repeat the procedure for a Windows 3 1x environment on the same system Installing the ASPI drivers to an existing MS DOS system The ASPI driver is found on the INI 9XXXU 9XXXUW DRIVER DISK 1 It is important that the SCSI bus hardware and operating system are installed correctly before proceeding further If you need help installing the MS DOS operating system please refer to the MS DOS manual before proceeding 1 Turn on host system and boot into MS DOS 2 Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into your floppy drive 3 At the MS DOS prompt change to your active floppy drive e g type A lt ENTER gt 4 Type DOSSETUP lt ENTER gt A series of screens will guide you through the installation of the ASPI device drivers 5 The first screen sets th
46. nly memory ROM to provide the e e e e e e e necessary configuration mechanisms for installation configuration and booting without user intervention 133 MBytes per second PCI burst mode The 32 bit data path for the PCI bus structure running in a synchronous mode at 33 MHz gives maximum operating speeds of 133 MBytes second 10 MBytes per second data transfer Up to 10 MBytes sec synchronous FastSCSI data transfers for I OHIGHWAY Programmable Automatic SCSI Termination Allows the user to choose between programmable or auto SCSI termination eliminating the need to remove system unit covers each time a change is made in SCSI bus configuration Onboard BIOS supports MS DOS Windows 3 1x I OHIGHWAY has the necessary software support on board allowing you to run disk drive operations for MS DOS and Windows 3 1x without any extra drivers Windows 95 Windows NT OS 2 SCO UNIX UnixWare Linux and NetWare Driver Support OHIGHWAY is compatible with all major operating systems ISGE Integrated Scatter Gather Engine Initio host adapters have incorporated advanced hardware functions to provide increased performance in all Scatter Gather operations No Hardware Jumpers to set Initio host adapters embed an intelligent software utility to set configuration options Compatible with Hard Disk CD ROM Optical Tape Printer and other SCSI products OHIGHWAY is a complete FastSCSI impleme
47. ntation All peripherals are compliant with SCSI 2 and SCSI 1 and can be used with I OHIGHWAY 64 byte FIFO A 64 byte FIFO buffer is designed into I OHIGHWAY and is utilized as a caching buffer to manage PCI to SCSI bus structure timing for data and command transfer initio Product Features Specifications e Command Queuing A unique implementation to provide 255 simultaneous SCSI commands SCSI compliant OHIGHWAY is fully SCSI compliant implementing advanced features such as e Tag Queuing e Sync Async Transfers e Disconnect Reselect Arbitration Product Specifications Power Requirements e 5 0 0 25 Vat 0 51 Amps maximum not including bus termination Physical Dimensions e 5 75 x 3 40 14 61 cm x 8 65 cm Environmental Specifications Operating Temperature e 0 to 55 C 32 to 131 F e 10 to 90 relative humidity non condensing Storage Temperature e 40 to 75 C 40 to 167 F e 5 to 95 relative humidity non condensing initio Getting Started Host Adapter and the SCSI Bus I OHIGHWAY is a bus mastering host adapter which works with the host computer to provide control for the SCSI bus By daisy chaining peripheral devices together up to seven devices can be linked with I OHIGHWAY The host adapter can be placed in any standard PCI slot on the bus SCSI bus preparation Each peripheral device attached to the SCSI bus can either be an internal or external device Each peripheral h
48. osoft Windows NT Driver Installation 3 In the INSTALL DRIVER window select HAVE DISK 4 Inthe INSTALL FROM DISK window that is displayed enter the Initio Driver path name e Insert INI 9XXXU 9XXXUW DRIVER DISK 1 into drive A e Type A WINNT select OK 5 Select Initio INI 9XXXU UW PCI SCSI Host Adapter select OK to install the INI910U SYS driver onto your hard disk drive 6 Inthe WINDOWS NT SETUP window that is displayed enter the Initio Driver path name to continue e Type A WINNT select CONTINUE 7 This completes updating the Host Adapter Driver Follow the on screen directions to restart you computer and activate the new driver 8 It is highly recommended that you verify Initio s Windows NT device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SCSI ADAPTERS from within the CONTROL PANEL group e Select Initio INI 9XXXU UW PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed Installing a new Windows NT system and Initio driver without floppy disks For computer systems installing or upgrading to Windows NT from a floppyless setup such as a share on your network these instructions will guide you through the INI 9XXXU 9XXXUW host adapter driver installation The Windows NT drivers are located on the INI 9XXXU 9XXXUW
49. pliant systems It is important that the Initio INI 9XXX hardware has been properly installed before proceeding further I 2 3 Microsoft Windows 95 will detect the presence of new hardware upon boot up and will display a dialog window titled update Device driver wizard Insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into floppy drive e Select NEXT e Select the OTHER LOCATION e Type A Win95 then select OK e Select FINISH e At window Insert Disk labled INI 9XXXU 9XXXUW driver select OK e At window titled Copying file replace the highlighted directory path with A Win95 then select OK this will complete loading the INI910U MPD driver onto your hard disk drive Restart your computer It is highly recommended that you verify Initio s Windows 95 device driver by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter entries from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed initio eC Microsoft Windows 95 95b OSR2 Driver Installation Updating the Initio Windows 95B OSR2 Device Driver 1 Once a Windows 95 session is established selec
50. plies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operations Class B Equipment Information to User This equipment has been tested and found to comply with the limits for a CLASS B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a resi dential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions contained in this manual may cause harmful interference to radio commu nications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that of the receiver Consult the dealer or a experienced audio television technician Note Connecting this device to peripheral devices that do not comply with CLASS B requiremen
51. re installed correctly before proceed ing further 1 Once an OS 2 session is established insert the INI 9XXXU 9XXXUW DRIVER DISK 1 into your floppy drive 2 By usi ng your installed mouse or by using the appropriate key strokes select DEVICE DRIVER INSTALL from the SYSTEM SETUP group 3 Select CHANGE source directory to read as the root directory 4 Select OS2 and select SET 5 Select DESTINATION DIRECTORY 6 Select CHANGE destination directory to any existing OS 2 directory or accept the default 7 Select SET 8 From the DEVICE DRIVER INSTALLATION GROUP select INSTALL 9 Select INITIO INI 9XXX Device Driver for OS 2 select OR 10 Select EXIT to install the OS 2 device driver Exit and reboot the system to activate the device driver initio IBM OS 2 Driver installation Device driver command line options The Initio device drivers support command line switches to optimize driver performance Device drivers normally require no further information to work effectively However in certain situations some driver optimization may be advantageous to system perfor mance From inside the CONFIG SYS file use the following format to edit the file The standard format for command line switches is BASEDEV INI910U ADD Driver Config Option Driver Config Options N IIV IET IET T hhhh B b dd B b A n DM t t t IDM t t t SM t t t ISM t t t Q q NO Verbose Mode provides detail
52. rporation prove to be defective Initio Corporation will at its option repair or replace the product once it has been returned to Initio Corporation free of charge Any replaced parts or products become the property of Initio Corporation You may obtain warranty service by first getting authorization from Initio Corporation then returning this product with proof of delivery date shipping charges prepaid to Initio Corporation This warranty does not apply to the software component of the product nor to any product which has been subjected to misuse accident abuse or use in a manner inconsistent with normal host adapter operations The original purchaser must be registered with Initio Corporation by mailing the Product Registration Card to qualify for warranty coverage This remedy is your exclusive remedy for breach of this warranty INITIO DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED INCLUDING ANY WARRANTY OF MER CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE INITIO SHALL BE LIMITED TO THE WARRANTY PERIOD SPECIFIED ABOVE ALL OTHER WARRANTIES ARE EXCLUDED INITIO S TOTAL LIABILITY HEREUNDER SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT PURCHASED IN NO EVENT SHALL INITIO BE LIABLE FOR ANY INDI RECT SPECIAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFOR MANCE OF THE PRODUCT EVEN IF INITIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES FCC Compliance Statement This device com
53. rs per drive to 1024 The host adapter defines head and sector usage to 64 heads and 32 sectors This format allows for maximum capacity of 1 gigabyte per disk storage e YES The upper limit can be extended from 1 GByte to 8 GBytes by increasing the number of heads to 255 and sectors used per track to 63 This is a powerful option DATA CAN BE LOST BY CHANGING SETTINGS Spin Up Disk Drive This option is used to initiate motor spin up for SCSI disk drives The host adapter BIOS can limit system power requirements during power up This is accomplished by signaling the device to start at delayed intervals default setting will be no Enable Disconnect The host adapter uses this option to allow a device to temporarily disconnect from the SCSI bus referred to as disconnect reconnect This allows the host adapter to perform other functions on the bus while the device is temporarily disconnected The device and the host adapter can then reconnect when the bus is needed default setting will be yes Adapter Setup Host Adapter SCSI Bus ID Used to change the adapter s SCSI ID on the SCSI bus The narrow host adapters provides eight ID s available numbered 0 7 with 7 having the highest priority and ID 7 reserved for the host adapter Installation of additional host adapters is permitted on the same PCI bus This will allow the system to have more than one SCSI bus attached Under these conditions SCSI ID s can be repeated
54. s configured to have more than one host adapter inserted into at least two distinctly different computer systems sharing peripheral devices In these circum stances it is possible to have one of the two computer systems turned off Under these conditions the host adapter has a jumper that can be enabled closed to set the active on board termination on all the time regardless of whether power is applied or not The host adapter is shipped without the jumper installed and need not be changed in most cases 7 Close the cover on the host computer Visually inspect the configuration you have installed to verify that all cables have been inserted correctly Close the cover on the host computer The hardware installation for the host adapter is now complete 8 Host computer configuration Most computer manufacturers with a PCI bus automatically configure the add on card or host adapter I O Port address IRQ Channel and BIOS address If this is not the case with your computer system you will need to manually configure your system There are two means of configuring the PCI bus from the host computer system 1 Setting jumpers on the host system motherboard 2 Setting CMOS BIOS incorporated into the host system You will need to refer to the host computer system documentation to complete PCI bus activation and setup If the host system will be using a SCSI device to provide system boot capability then the system CMOS drive type settings may ne
55. s fixed disks With this option selected you can run removable disk media without additional software drivers The default setting will be off No BIOS Support for Bootable CD ROM This option allows users to boot from a CD ROM by replying with Yes at the prompt Only one bootable CD ROM will be allowed at a time The default setting will be off No Disk Utilities Format Disk Use this option to perform a low level disk format on the target device The format will erase all data resident on the targeted disk drive Refer to the section titled Hard Drive Preparation for additional information Verify Disk This option will verify the media of a successfully formatted device and verify that the drive is functioning properly Verify will also identify and flag any bad sectors on the disk so that during operation these flagged sectors will not be used If a bad sector is found you are given two options shown below e Reassign will assign the flagged location to another sector on the disk e Skip will not reassign the flagged location initio MS DOS Windows 3 1x Driver Installation Overview The Initio ASPI driver will support extended SCSI command functions for MS DOS 3 30 or later The on board BIOS initialized during the power up boot routine only supports MS DOS hard disk operation If peripherals other than disks are used such as CD ROM or MO the Initio ASPI driver will need to be installed in addition to Initio CD ROM a
56. t MY COMPUTER from your desktop Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group e Select SYSTEM from within the CONTROL PANEL group e Select the DEVICE MANAGER tab from within the SYSTEM group e Select the SCSI CONTROLLERS category from within the DEVICE MANAGER listing e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter sub categories from within the SCSI CONTROLLERS listing or any other INI 9100U UW class of drivers if you are using an older Initio product N In the INI 9XXXU 9XXXUW SCSI HOST ADAPTER PROPERTIES window select the DRIVER tab then select UPDATE DRIVER e Select Next e Select the OTHER LOCATION e Type A WIN95 then select OK e Select FINISH e At prompt Insert Disk labled INI 9XXXU 9XXXUW driver select OK e At prompt Copying file replace the highlighted directory path with A Win95 then select OK This will complete loading the INI910U MPD driver onto your hard disk drive This completes updating the Host Adapter Driver Follow the on screen directions to restart you computer and activate the new driver It is highly recommended that you verify Initio s Windows 95 device driver by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER lis
57. ter which provides the interface between the FastSCSl bus and the PCI local bus Distiguishing features include e Support of 32 bit data transfers across the PCI bus at speeds up to 133 MBytes per second e The SmartSCSI Setup Utility program enables integration of the host adapters into most platforms and operating systems e Compliancy with Plug n Play applications on systems using the PCI bus standard I OHIGHWAY host adapter supports synchronous FastSCSI bus transfers at a rate of 10 MBytes per second I OHIGHWAY utilizes full support of FastSCSI standards defined by SCSI specifications initio Technical Illustration This illustration identifies major components pertaining to your I OHIGHWAY host adapter You will find it helpful to refer to this illustration while installing the host adapter and attaching the cables External UltraWide SCSI Connector M Internal FastSCSI Connector To Il O QUUUUUUUUUCUOUOUOUUUUUo i LED Connector J3 o M e E Jumper JP1 i UU AU UA FIGURE 1 INI 9100A Board Layout initio Product Features Specifications Product Features e PCI Compatibility The PCI Bus is a 32 bit bus with multiplexed address and data lines I OHIGHWAY is compliant with PCI 2 1 bus protocol electrical and mechanical specifications e Plug and Play OHIGHWAY has an on board read o
58. ting and e Select the Initio INI 9XXXU UW PCI SCSI Host Adapter entries from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed initio Microsoft Windows NT Driver Installation Overview I OHIGHWAY will support Windows NT v3 5x 4 0 with the addition of a software driver A software driver allows the host computer the ability to transfer data over the SCSI bus The device driver for Windows NT is copied from the Initio driver installation diskette to your hard drive where it is loaded onto the computing system during installation The following files are used for installation and may be found on the INI 9XXXU 9XXXUW DRIVER DISK 1 WINNT INI9 10U SYS INI 9XXX SCSI Host Adapter Windows NT miniport driver WINNT TXTSETUROEM Script file for installing INI910U SYS during the text setup phase WINNT OEMSETUPINF Script file for installing INI910U SYS during the windows phase Installation The INI 9XXX driver developed for Windows NT will be installed on the hard drive used for system initialization The driver is loaded during the system boot routine and will remain resident on the drive This is accomplished by following one of the two installa tion procedures listed e New Windows NT installation e Adding or updating the INI 9XXX Host Adapter Driver to an existing Windows NT System The procedures described to make changes to the system h
59. tion A new SCSI disk drive is normally low level formatted at the factory to simplify installa tion The drive can be used as it comes from the factory once it is partitioned for system operation Low level Format A low level format will erase any data that is stored on the target disk Before attempting to perform a low level format be sure the data on the target disk has been backed up A low level format can be achieved via the SmartSCSI Setup Utility for OHIGHWAY The low level format sets the media to a state which is easily recognized by the host adapter on the SCSI bus Once this format is completed you will need to partition the drive Refer to your operating system documentation for further information on parti tioning drives initio Host Adapter Setup Running the SmartSCSI Setup Utility To start the SmartSCSI Setup Utility verify that all devices attached to the SCSI bus are powered up when the host computer system is turned on Once the power switch has been turned on and the system begins its on screen power up sequence the Initio banner will be displayed for a brief period During this time the Initio SmartSCSI Setup Utility is accessible by pressing the lt Ctrl gt key and the lt I gt key at the same time When displayed on your system monitor the following message indicates that the host system is ready to accept your keyboard input I Press lt Ctrl gt lt I gt for SmartSCSI Setup Utility Mai
60. tions about installing or using Initio products check this document first You will find answers to most of your questions here If you need further assistance please contact us We offer the following support and information services Monday Friday 8 00 AM to 5 00 PM Pacific time e Toll Free 800 99 INITIO e Phone 408 577 1919 Fax 408 577 0640 Initio provides on line support for software upgrades utility programs and other information 24 hours a day using 8 data bits 1 stop bit and no parity at speeds up to 28 8K baud e Initio Corporation BBS 408 577 0431 World Wide Web http www initio com Email support initio com Outside of the US and Canada contact your authorized Initio distributor If you received your Initio hardware product as original equipment in a computer system or as part of a hardware bundle please contact that manufacturer for technical support The following information is needed to assist in problem resolution e Model type e Serial number e Product description e Operating system amp version number i e Windows 95 e Software driver product type and version number e Motherboard BIOS version e Location of purchase The README TXT File The README TXT file on the INI 9XXXU 9XXXUW DRIVER DISK 1 contains important updated information and corrections to this User s Manual README is a standard ASCII text file that may be read with any word processor or text editor To view the
61. to the SCO UNIX Documentation for additional information You have completed the installation of the SCO UNIX driver Adding the Initio driver to an existing SCO UNIX system 1 Insert the INI 9XXXU 9XXXUW DRIVER DISK 2 diskette into your floppy drive 2 Type installpkg under the command prompt lt ENTER gt 3 The system will ask you what packages you wish to install Type i91u lt ENTER gt 4 Change the directory and rebuild the UNIX kernel e cd etc conf cf d lt ENTER gt e link_unix lt ENTER gt 5 You have completed the link procedure for the Initio device driver Exit and reboot the system initio Changing to the INI 9XXX as the bootable host adapter 1 Insert the INI 9XXXU 9XXXUW DRIVER DISK 2 diskette into floppy drive 2 Type installpkg under command prompt and press lt ENTER gt The system will ask you what packages you want to install e Type i91u lt ENTER gt 3 Change the mscsi file e cd etc conf cf d lt ENTER gt e cp mscsi mscsi bak lt ENTER gt e vi mscsi lt ENTER gt In the example below The XXXX would be replaced with i9 1u ha attach number ID lun XXXX Stp 0 2 0 XXXX_ Sdsk 0 0 0 XXXX Srom 0 5 0 4 Rebuild the UNIX kernel e link_unix lt ENTER gt 5 You have completed the link procedure for the Initio device driver Exit and reboot the system initio Overview The I OHIGHWAY SCO UnixWare device driver will support UnixWare 2 x The device driver
62. ts or using an unshielded peripheral data cable could also result in harmful interference to radio or television reception initio ee Product Warranty The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment To ensure the use of this product does not contribute to interference it is necessary to use shielded I O Cables Reprinted from the Code of Federal Regulations 47 part 15 193 1993 Washington DC Office of the Federal Register National Archives and Records Administration U S Government Printing Office Declaration of the Manufacturer Importer We hereby certify that the IMOHIGHWAY PCI FastSCSI Bus Master Host Adapters in compliance with the require ments of BMPT Vfg 243 1991 is RFI suppressed The normal operation of some equipment e g signal genera tors may be subject to specific restrictions Please observe the notices in the user s manual The marketing and sale of the equipment was reported to the Federal Office for Telecommunication Permits BZT The right to retest this equipment to verify compliance with the regulation was given to the ZZF EN 55 9100UW2 Declaration of Conformance This is to certify that the I OHIGHWAY PCI FastSCSI Bus Master Host Adapter is shielded against the generation of radio interference in accordance with the application of Council Directive 89 336 EEC Article
63. und on the INI 9XXXU 9XXXUW DRIVER DISK 1 It is important that the INI 9XXX hardware has been installed successfully before proceeding further 1 Make a duplicate copy of OS 2 Diskette 1 using a blank diskette and label it as OS 2 Diskette 1 for INI 9XXxX 2 Copy the INI910U ADD file from the INI 9XXXU 9XXXUW DRIVER DISK 1 OS 2 subdirectory to the root directory on the OS 2 diskette 1 for INI 9XXX initio Ci IBM 0S 2 Driver Installation 3 Using an appropriate text editor modify the CONFIG SYS on the OS 2 Diskette 1 for INI 9XXX to include the new Initio driver Enter BASEDEV INI910U ADD and save the file 4 Insert t begin t he Installation Diskette into drive A and turn on your computer This will he OS 2 installation and establish an OS 2 bootable hard drive 5 When prompted insert the OS 2 Diskette 1 for INI 9XXX Follow the on screen instruc tions to continue 6 You have completed the Initio device driver installation for OS 2 Follow the on screen instruc tions and OS 2 manual for a complete description of OS 2 installation Adding the Initio driver to an existing OS 2 system For comp uter systems using other SCSI host adapters or an IDE device to provide the system boot routines these instructions will guide you through INI 9XXX host adapter driver installation The OS 2 driver will be found on the INI 9XXXU 9XXXUW DVR DISK 1 It is important that the SCSI bus hardware and OS 2 a
64. ws manually e Choose CUSTOM INSTALL to select DOS ASPI drivers or the Windows 32 bit Disk Access drivers manually Use this option only if you are familiar with configuring a DOS or Windows PC manually 5 Follow the on screen directions and or options to continue the installation e Choose CONTINUE to accept the default directory or enter the full directory where you want ASPI drivers installed e Choose CONTINUE after all the files have been copied and installed to your system e Select YES to make the required changes to your system s CONFIG SYS and SYSTEM INI configuration files e Once the SETUP COMPLETE screen is displayed choose CONTINUE 6 Last minute changes to this User s Manual will be displayed in the README TXT file that is shown To exit the README TXT file use your installed mouse or the appropri ate key strokes to select FILE then EXIT from the Note Pad FILE MENU 7 To complete the installation and activate the device driver exit from your Windows 3 1x session and reboot the system by pressing lt CTRL gt lt ALT gt lt DEL gt initio ee MS DOS Windows 3 1x Driver Installation ASPI Manager Command Line Options Below is a list of command line options The Initio ASPI Manager ASPI910U supports command line switches to optimize driver operation From inside the CONFIG SYS file for MS DOS use the following format when modifying the device driver switches The standard format for command l

Initio I/O HIGHWAY User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents