Husqvarna 9H User's Manual
Contents
1. e Rotate Outer Flange 2B and the Blade 2E in the opposite direction of blade rotation to remove back lash e Install and tighten Blade Flange Nut using the Blade Shaft Wrench 50 lb ft 68 N m while firmly holding the Diamond Blade 2E e Lower front half of Blade Guard 2H movement to stop Note the direction of rotation of the blade The direction of rotation is shown by an arrow on the Diamond Blade 2E Make sure that the contact surfaces on the Diamond Blade 2E Inner amp Outer Flanges 2B amp 2F and Blade Arbor are clean The Blade Shaft Nut 2A on the Right Hand side has Left Hand threads 13 To Maneuver the Saw ET Set the handle bar height to a comfortable position Raise the Blade 2E as high as possible so that the Blade 2E will not strike pavement when a To Start Sawinc Follow all of the instructions outlined above Open the Water Valve 1A FULL open Check the water to verify full flow then adjust for proper amount of water on the blade BEFORE you lower the Blade Y Test for adequate water supply 2 1 2 to 5 gal min 10 to 20 lit min Low water flow will cause damage to diamond blades If water supply is interrupted stop cutting immediately Screw Feed Version 14 Lower the blade into the cut by pulling up on the Depth Control Lock 1E and slowly turning the Hand Wheel COUNTER CLOCKWISE When the desired depth of cut is reached pus2. Diagram 1 Frame A e e o 5 o 18 19 Diagram 2 Depth Control Screw Feed msc ee 20 21 Diagram 3 Pointer amp Belt GUSTO rinitis 22 23 Diagram 4 Guards amp Water Distribution u aa nee 24 25 Diagramm 9 Blade NNN 26 27 Diagram 6 Engine amp Blades een ee arg 28 29 Diagram 7 Kil Water Tank 174957 anne an han 30 Symbol Definitions Definicion De Simbolos e Please Read The Instructions For Use Prior To Operating The Machine For The First Time Antes De La Puesta En Marcha Lea Detenidamente Las Instrucciones Y Familiaricese Con La Maquina e Mandatory Obligatorio Indication e Indicaci n Prohibition Prohibici n e Warning Triangle e Tri ngwulo De Advertencia e Wear Eye Protection e Usar Gafas De Protecci n e Wear Head Protection e Usar Casco De Protecci n e Wear Breathing Protection e Usar M scara De Protecci n e The Use Of Ear Protection Is Mandatory Es Obligatorio El Uso De Protecci n Auditiva Wear a Hard Hat Usar Casco Duro e Wear Safety Shoes e Usar Zapatos De Seguridad e Wear Appropriate Clothing e Usar Ropa Adecuada e Remove The Blade Prior To Hoisting Loading Unloading And Transporting The Machine On Jobsite e Desmontar El Disco Antes De Desplazar Cargar Descargar O Transportar La M quina En La Obra Motor Off Parar El Motor Use In Well Ventilated Area Usar En Una Area Bien Ventilada POOGGOGOO gt gt 4 gt OOP OO
3. HWV Do Not Use In Flammable Areas No Usar In Areas Inflamables Machinery Hazard Keep Hands And Feet Clear Maquina Peligrosa Mantenga Manos Y Pies Alejados De La Maquina Danger Poison Exhaust Gas Peligro Gas De Escape Venenoso No Non working Personnel In Area Prohibido Para Personas Ajenas A La Obra No Smoking No Fumar Do Not Operate Without All Guards In Place No Operar Sin Todas Las Protecciones In Su Sitio Always Keep the Blade Guards In Place Mantenga Siempre Las Protecciones De La Hoja En Su Sitio Water Supply On Suministro De Agua Desconectado Water Supply Off Suministro De Agua Des Conectado Keep Work Area Clean Well Lit Remove All Safety Hazards Mantenga Limpio EI Sitio De Trabajo Bien Iluminado Elimine Todos Los Riesgos De Seguridad Dangerously High Noise Level Nivel De Ruido Elevadamente Peligroso Pay Extreme Attention To The Care And Protection Of The Machine Before Starting Up Ponga Extrema Atenci n Al Cuidado Y Preparaci n De La M quina Antes De Ponerla En Marcha Remove Tools From Area And Machine Elimine Las Herramientas Del Area Y De La M quina Oil Required Necesita Aceita Dipstick Maintain Proper Oil Level Varilla De Control Mantenga EI Nivel De Aceite Correcto Lubrication Point Punto De Lubrication Unleaded Fuel Only Combustible Sin Piomo Solamente Repairs Are To Be Done By An Authorized Dealer Only Las Reparaciones Deben Ser Efectuadas Unicamente Por Un Distribuidor Autori
4. Husqvarna IPL MC 18 2007 09 542 20 11 33 MC 18 Spare Parts amp Operator s Manual Piezas de repuesto y Manual del operador MC 18 9H MC 18 13H 542 20 11 33 SSeS HUSQVARNA CONSTRUCTION PRODUCTS EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION CONTENTS MD 3 5 Decal Descriptions and Locations cccccecccceseecceseeeceuseeceseeseeueecuesecseuseessaeeeseuseesseeessassessuaeessees 6 Saw Configurations and Models Power Source Dimensions rrrrnnnnrnnrnnnnnonnnnnnnvnrnnnnnnnnvannnennnnnnnenn 7 Safety Warnings DO s amp DO NOTE nenn ee een 8 9 EEE sje nn o A o O PU IA 10 Pre Operation Checklist Maintenance Schedule oooonccnncccccconcnnccccnnonnnnnncnnnanncnnnnnnnnnnncnnnnonananennnnnss 11 Instructions le FU re 12 E EE NE EE 12 3 General Instructions Ene 12 EPER 13 a Ay 13 6 EP TE 13 Ts Maneuver the SAW Lasser ee ae kll ie er miin 14 O Ama ee 14 9 S N ESN 14 10 Maintenance eo 176 EEE EN M 15 11 Optional And Accessory Field Installed oooccccccccconnncnnccccnoncconcconnonnconnonononenonncnnnnos 15 GE 01409931 BE SEE I A ae ee aaa am 16 1 RER EEE NR 16 14 FI 16 Parts List Diagrams
5. transport a cutting machine with the blade mounted on the machine use a blade that has been dropped or damaged use carbide tipped blades touch a dry cutting diamond blade immediately after use These blades require several minutes to cool after each cut use damaged or worn blade flanges allow other persons to be near the machine when starting refueling or when the machine is in operation operate this machine in an enclosed area unless it is properly vented operate this machine in the vicinity of anything that is flammable Sparks could cause a fire or an explosion allow blade exposure from the guard to be more than 180 degrees operate this machine with the belt guard or blade guard removed operate this machine unless you are specifically trained to do so use a blade that has been over heated Core has a bluish color jam material into the blade grind on the side of the blade lay power cords in or near the water tow this machine behind a vehicle replace the motor with any motor that does not have a special grounding connection operate this machine while under the influence of drugs or alcohol kkkkkkkkkkkkkkkkk This saw was designed for certain applications only DO NOT modify this saw or use for any application other than for which it was designed If you have any questions relative to its application DO NOT use the saw until you have written Diamant Boart Inc and we have advised you Husqvarna Constructuion Products N A
6. 17400 West 119th Street Olathe Kansas 66061 USA FIGURE 1 1A 1B 1C 1D 1E 1F 10 WATER VALVE Use to control the water supply to the diamond blade WATER INLET Connect water hose at this garden hose connection HANDLE ADJUSTMENT KNOBS Use to adjust handle height ENGINE STOP SWITCH Stop Switch Push down to stop engine DEPTH CONTROL LOCK Use to lock the position of the Depth Control Hand Wheel DEPTH CONTROL HAND WHEEL Controls lowering and raising of the blade into and out of the cut FIGURE 2 2A 2B 2C 2D 2E 2F 2G 2H 21 BLADE SHAFT NUT Use to tighten the outer flange against the diamond blade OUTER FLANGE Use to hold the diamond blade in position NOT USED LOCKING PIN Use to prevent the diamond blade from rotating on the shaft during operation DIAMOND BLADE Use as the cutting tool for concrete and asphalt surfaces INNER FLANGE Inside support used to hold the diamond blade in position NOT USED BLADE GUARD FRONT The front section of the blade guard BLADE SHAFT Supports the blade flanges and PRE OPERATION CHECKLIST Before leaving our factory every machine is thoroughly tested Follow our instructions strictly and your machine will give you long service in normal operating conditions Before starting up the machine make sure you read this entire operations manual and are familiar qe with the operat
7. Capscrew Hex Hd 375 16UNC x 1 25 13H Locknut Fiber 375 16UNC Adapter M12 x 10mm Hose Barb 9H 13H Hose Assembly Oil Drain Hose Clamp Worm Drive Cap Blanking Tube Nut M16 Assy Cord Pulley Assy 3G3V 2 65 Dia w ss serer Set Soc CHR PE 250 Z20UNC 25 Key square 250 x 1 25 Lg V Belt 3VX300 set of 3 13H V Belt 3VX280 set of 3 9H V Belt 3VX300 13H V Belt 3VX280 9H O i HHHHHr PARRPWABRNY onner BRONN ARRRR HPNbPhPH HWHHHNDH 29 Diagram 7 Kit Water Tank 174957 30 INDEX Ol B UN FP OLONA 12 13 14 P N 502479401 174648 020764 020509 020199 020322 139722 020049 174016 174741 196037 187667 196058 187667 BILL OF MATERIAL DESCRIPTION Bracket Water Tank Water Tank w cap 7 Gallon Washer Flat 375 SAE Capscrew Hex Hd 375 16UNC x 2 00 Locknut Fiber 375 16UNC Capscrew Hex Hd 375 16UNC x 75 Hose 3 8 ID x 4 4 Hose Clamp Worm Drive Fitting Hose Barb 3 8 ID x 3 4 Male Kit Quick Disconnect Garden Hose w Valve Fitting 3 4 FGH SWV x 1 4 HB Nylon Hose 1 4 ID x 7in Fitting 1 4 Y Nylon LP Hose 1 4 ID x 9in OD i HHNHN ABANAHPEH AY DHHH NOTES NOTAS Husqvarna Construction Products N A Corporate Office 17400 West 119th Street Olathe Kansas 66061 Tel 913 928 1000 Fax 913 438 7951 Customer Service 800 288 5040 Customer Serv Fax 800 825 0028 A DUST WARNING A Cutting especially when DRY c
8. Machined Adapter 3 8 NPT x Male Garden Hose Capscrew Hex Hd M6 x 1 0 x 40mm OD i ADEHR DN DD IA EQ on ERE IE H HD No H 21 Diagram 6 Engine amp Bladeshaft 28 Diagram 6 Engine amp Bladeshaft INDEX Ol B WD KE O WO 0 Q OV 12 de 14 LS 16 L7 18 19 20 21 22 24 25 26 27 28 29 30 31 32 33 34 35 P N 174973 177569 167185 167962 167964 167846 167847 020067 139300 020541 162633 174962 020743 020330 020199 177958 16 7751 174962 174736 020743 020786 020377 020380 020522 048740 020199 167133 167305 020049 167306 167622 174999 167746 020540 020067 139613 139614 047455 058020 BILL OF MATERIAL DESCRIPTION Group Bladeshaft R amp L 4 5 9H 13H Bladeshaft Assy Complete 9H 13H Collar Inner 4 50 OD Collar Outer 4 50 OD Assy Pin Drive Nut LH Thread Bladeshaft Nut RH Thread Bladeshaft Key Square 250 x 1 25 Lg Pulley Assy 3GR 3V 3 65 9H 13H Screw Set Soc Cup Pt 2509 20 UNE x 3 75 Bearing lin Pillowblock BB Spacer Bearing Washer Flat 375 Dia Capscrew Hex Hd 375 16UNC x 3 00 Locknut Fiber 375 16UNC Engine 13HP Honda Modified Engine 9HP Honda Modified Spacer Bearing 9R 13R 13H Plate Adapter 13H Only Washer Flat 375 Dia Lockwasher Split 375 13H Only Capscrew Hex Hd 375 16UNC x 1 50 13H Capscrew Hex Hd 375 16UNC x 1 75 9H Capscrew Hex Hd 375 16UNC x 75 13H
9. 020742 020785 020313 BILL OF MATERIAL DESCRIPTION Guard Belt Lockwasher Split 313 Capscrew Hex Hd 312 18UNC x 75 Water Valve Assy MC18 Water Valve Elbow 1 2NPT Male x 90 Brass Hose Adapter Filter Washer Washer Hose Hose Assy Water MC18 Lockwasher Split 10 Screw Rd Hd Mach 10 24 x 500 Cross Z P Assy Blade Guard 18in Husq Gray Washer Flat 375 Dia Capscrew Hex Hd 375 16UNC x 3 75 Locknut Fiber 375 16UNC Washer Flat 313 Dia Lockwasher Split 313 Capscrew Hex Hd 312 18UNC x 75 O i HHHNDND HHHHH HHPRrHH HHHh 25 Diagram 5 Blade Guard 26 Diagram 5 Blade Guard INDEX Ol B WD KE O WO 0 Q OV 12 2 14 15 16 17 18 19 20 21 22 P N 50244701 195127 159596 173059 167478 139738 139098 167761 173047 172316 020782 172011 040330 049212 167818 139745 167046 020864 139051 139045 040275 167551 BILL OF MATERIAL DESCRIPTION Rear Guard Weldment 18 Inch Husq Gray Hinge Front Guard Weldment 18 Inch Husq Gray Washer Flat M8 Capscrew Hex Hd M8 x 1 25 x 25mm Locknut Fiber M8 x 1 25 Splash Flap Capscrew Hex Hd M5 x 0 8 x 20mm Washer Flat M5 Locknut Fiber M5 x 0 8 Lockwasher Split 10 Nut Hex Hd M5 x 0 80 Spring 375 OD x 054 Dia Clamp Water Tube Capscrew Slot Flat Hd M6 x 1 0 x 16mm Locknut Fiber M6 x 1 0 Water Tube 18 Inch Plug Soc Hd 1 8 NPT Brass Gasket Water Manifold Water Manifold
10. will give you long service in normal operating 1 Features A Use Wet sawing of old and new concrete and asphalt Tools Diamond blades water cooled 9 10 12 14 18 and 20 with Arbor 1 For information contact your Husqvarna supplier CUTTING DEPTHS MAXIMUM BLADE DEPTH To Collar MC18 MAXIMUM DEPTH To Depth Stop 2 1 2 62mm 3 1 2 87mm 4 1 2 112mm 6 1 2 158mm 2 3 4 68mm 3 3 4 93mm 4 3 4 118mm 6 3 4 164mm Before starting up the machine make sure you read this entire manual and are familiar with the operation of this machine The working area must be completely clear well lit and all safety hazards removed The operator must wear protective clothing appropriate to the work he is doing Any persons not involved in the work should leave the area Use only blades marked with a maximum operating speed greater than the bladeshaft speed 12 E The Handle must be attached Place Handle in position and securely tighten Knobs Check the engine oil level Service before using Refer to the engine operation manual for detailed information 3 General Instructions Remove the Blade 2E before transport WARNING DO NOT operate without the proper blade guard over the Blade 2E WARNING DO NOT operate the saw with the front of the Blade Guard 2H raised WARNING Blade exposure CANNOT exceed 180 degrees when operating
11. A The Front Pointer must be checked for alignment with the Blade 2E It must be in line with the Blade 2E mounted on the Blade Shaft 21 For WET SAWING be sure the water jets in the blade guard water tubes are open and that each side of the Blade 2E has an adequate supply of water Test the water supply for pressure and quantity flow before starting to saw WATER FLOW from 2 1 2 to 5 gallons of water per minute MUST flow over the blade to properly cool it and to get maximum blade life DO NOT use conventional wet diamond blades without water e Saw only as deep as the specifications and job conditions require Sawing excessively deep is wasteful avoid it Step cut in increments of 2 inches 50 mm for best results Saw in a straight line Mark the cutting line clearly so the saw operator can follow the line without difficulty The saw should NOT be twisted from side to side try ing to force the blade back on the line Al Check Before Startinc 6 Starting The Power Source 6 E Always pay extreme care and attention to the ES fin preparation of the machine before starting Remove all wrenches and tools from the floor Take into account the working conditions from and the machine the health and safety point of view Always keep blade guard and transmission FUEL Check the engine maintenance manual guard in place Gas Models Unleaded gasoline is recommended Check that the engin
12. NC Capscrew Hex Hd 500 13UNC x 75 Decal Screw Feed O i FP BNNNHR NPhPkPP HHHNDH BRASS Proa HH 21 Diagram 3 Pointer amp Belt Guard 22 Diagram 3 Pointer amp Belt Guard INDEX Ol B WD FP O WO 0 Q OV 12 de 14 LS 16 17 18 19 20 21 22 P N 502469601 020785 020399 502469701 502437601 502437701 041231 041220 020786 020136 020199 172137 162761 020595 020195 139749 139748 040550 020786 020323 122696 020199 BILL OF MATERIAL DESCRIPTION Guard Shaft Weldment Lockwasher Split 313 Capscrew Hex Hd 312 18UNC x 3 25 Bracket Pointer Mount Bar Pointer Offset Bar Pointer Straight Rod Pointer Wheel 3in Dia Lockwasher Split 375 Nut Std Hex 375 16UNC Locknut Fiber 375 16UNC Rope Pointer Clamp Capscrew Soc Hd 250 20UNC x 625 Locknut Fiber 250 20UNC Capscrew Hex Hd M10 x 1 50 x 25mm Locknut Fiber M10 x 1 50 Hinge Block Pointer Lockwasher Split 375 Capscrew Hex Hd 375 16UNC x 1 00 Draw Bolt 3 8 16UNC Locknut Fiber 375 16UNC OD i NNNEHEH HHHHH PENNE A Ro ps GA H 23 24 Diagram 4 Guards amp Water Distribution gi m Diagram 4 Guards amp Water Distribution INDEX Ol B WD FP O WO 0 Q OV 12 de 14 LS 16 17 18 19 P N 502469801 020785 020313 174992 139021 169196 539300267 045640 040254 13961 6 020782 196039 1951293 020743 020233 020199
13. an added protective seal for the bearings Use only a Premium Lithium 12 based Grease conforming to NLG1 Grade 2 Consistency without Molybdenum Disulfide ENGINE OIL Check daily Keep the oil clean and at the proper level 10W30 MS SD SE or better is generally recommended Capacity levels indicated on page 10 DO NOT OVERFILL Change engine oil and oil filter every 50 HOURS ofoperation Refer to the engine manual for detailed information CLEAN ENGINE AIR FILTER Clean the air filter 2 or 3 times daily when dry cutting Refer to the engine manual for detailed information ENGINE CARE Refer to the engine manual for detailed information 11 Optional and Accessory Field Installed SPECIAL OUTER FLANGE ASSY 1 2 12 7mm WIDE CUT P N 167963 A Special Outer Flange Assembly is available as a field installed accessory It enables the MC 18 to cut 7 16 1 2 11 12 7mm wide WARNING This special outer flange assembly is for use with blade width stacks of 7 16 1 2 11mm 12 7mm only If blade width stacks of less than 7 16 11mm are required use the standard outer flange assembly supplied with the MC 18 The Special Outer Flange Assembly can be identified by the COUNTERBORE on the Nut Side of the flange The Standard Outer Flange Assembly has NO COUNTERBORE WATER TANK KIT A 6 gallon 23 liter Water Tank Kit is available as a Field installed accessory Use only for dry cutting The water tank is desig
14. e oil level is correct Because i the engine often operates at an angle check the oil On Gasoline Engine Models level with engine horizontal frequently to ensure that 1 Refer to the engine operating manual for proper engine the oil level never falls below the lower mark on the operation dipstick 10W30 oil is recommended 5 Fitting The Blade 2 Fillthe engine fuel tank and check the engine oil level Refer to the engine manual for detailed information 3 Startthe engine Refer to the engine manual for detailed See Fig 1 and 2 information A Always set the Engine Switch 1D to the OFF 4 Let the engine warm up at half throttle All sawing is position before mounting the Blade 2E done at full throttle The governor is factory set for the correct engine speed Do not change the Governor Set the Engine Switch 1D to the OFF position setting it is factory set for the correct speed e Raise the machine to a high position by cranking the Raise Lower Hand Wheel i by 9 WARNING To STOP ENGINE PUSH the e Raise the front half of the Blade Guard 2H Engine Stop Switch DOWN located en the handle support of the saw Wait for all engine e Unscrew the Blade Shaft Nut 2A Remove Outer Flange 2B e Fit Diamond Blade 2E on the Blade Shaft Arbor e Install Outer Flange 2B into the Blade Shaft 21 making surethatthe Locking Pin 2D passesthrough the Diamond Blade 2E and into the Inner Flange 2F
15. ension Nut Std Hex 500 13UNC Washer Flat 500 SAE Locknut Fiber 500 13UNC Spring Handle Bent Grip Handle Knob 3 8 16UNC 2A x 1 00 Wrench 1 1 16 Open End Wing Bolt M6 x 1 0 x 16 mm OD i ENNE WNIA KDN Ni pp AP H HNHHH RRPNDN 19 Diagram 2 Depth Control Screw Feed 20 Diagram 2 Depth Control Screw Feed INDEX Ol B WD KE O WO CO J OV 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 P N 174997 049924 542177915 542190434 502469901 020764 020786 020330 040153 040151 032250 020766 174956 020552 174994 160164 020540 177239 040183 174961 020010 020012 020762 020195 020788 030210 020668 174998 BILL OF MATERIAL DESCRIPTION Adj Nut Wldmnt w Grease Fit Fitting Grease 1 8 NPT x 90 Screw Adj 625 8 ACME Bearing Flange 50 Inch ID Bracket Screw Feed Washer Flat 375 SAE Lockwasher Split 375 Capscrew Hex Hd 375 16UNC x 3 00 Assy Hand Wheel wheel Hand Machined Handle Assy Revolving Washer Flat 500 SAE Bracket Stop Screw Set Soc Cup Pt 312 18UNC x 450 Spacer Adjustment Screw Pin Clevis 50 Dia x 1 13 Lg Screw Set 500 Cup PE 250 20UNC x 25 Pin Rue Ring 50 DIA Rubber Boot 3 Inch 20 ribs Hose Clamp Worm Drive SAE 24 Narrow Key Woodruff 405 Bolt Carriage 250 20UNC x 1 00 Washer Flat 250 SAE Locknut Fiber 250 20UNC Lockwasher Split 500 Nut Acorn LT 500 13U
16. h Depth Control Lock down to lock it in the hand wheel During cutting DO NOT exert excessive side pressure on the Handle Bars to attempt to STEER the saw Use only enough pressure to follow the previously marked line If the saw should stall for any reason raise the blade completely out of the cut before starting your power source again When lowering the Blade 2E into a partially made cut the blade must be perfectly aligned within the cut before starting to saw again DO NOT FORGE the Blade 2E into the material by lowering the Blade too fast or by propelling the saw too fast Screw Feed Version Raise the blade out of the cut by pulling up on the depth control lock and slowly turning the hand wheel clockwise Raise the blade 2E high enough out of the cut to clear the pavement when maneuvering the Saw Turn off the Water Valve 1A Turn the Engine Throttle to the IDLE position STOP the engine by turning the Engine Switch 1D to the OFF position Maintenance Before performing any maintenance ALWAYS park the machine on a level surface with the A Engine OFF and the Engine Switch in the OFF position After each use CLEAN the machine LUBRICATION E rA LUBRICATE DAILY Front Wheels and Blade Shaft Bearings LUBRICATE EVERY 50 HOURS Depth Control Adjustment Screw Screw Feed Version Only NOTE When cutting dry lubricate blade shaft bearings 2 or 3 times daily the grease provides
17. he shortest possible time and at the most economical prices See back page for our address and phone numbers For quick supply of spare parts and to avoid any lost time it is essential to quote the data on the manufacturer s plate fixed to the machine and the part number s to be replaced with every order Write the Model Number amp Serial Number here for future reference Model Number Serial Number The instructions for use and spare parts found in this document are for infor mation only and are not binding As part of our product quality improvement policy we reserve the right to make any and all technical modifications without prior notice 16 The manufacturer accepts no responsibility caused by unsuitable use or modifications NOTE NOTA Diagram 1 Frame amp Axle Diagram 1 Frame amp Axle INDEX P N 502470001 174942 174975 020768 040091 541201090 020551 020767 139569 541200649 020551 139638 020323 020199 139582 020140 020766 020201 139581 174946 542139568 12557 163988 197170 BILL OF MATERIAL DESCRIPTION Frame Weldment MC18 Axle Front Axle Pivot Washer Flat 75 SAE Wheel Assy 5 Inch Dia Lock Collar 750 ID w ss Screw Set Soc Cup Pt 312 18UNC x 225 Washer Flat 625 SAE Wheel 8 Inch Dia Lock Collar 625 w SS SELEN Set SoG Cup PE 1 2 L2 LoUNC X 25 Anchor Spring Capscrew Hex Hd 375 16UNC x 1 00 Locknut Fiber 375 16UNC Bolt T
18. ion of the machine WITH MACHINE COLD AND SETTING LEVEL 1 Check engine oil Fill to full mark on dip stick with 10W30 oil DO NOT OVERFILL e Gas Models Class MS SD SE or better 1 2 HOUR OPERATION CHECK ALWAYS park machine on a level surface with the engine OFF and the engine switch set in the OFF position before performing any maintenance Let the machine cool down 1 Tension the blade drive V belts DO NOT over tension SCHEDULED MAINTENANCE QUICK REFERENCE Before performing any maintenance ALWAYS park the machine on a level surface with the engine OFF and the engine switch set in the OFF position SERVICE DAILY Check engine oil level Check blade guard for damage Check engine air filter replace if dirty Lubricate bladeshaft bearings Lubricate front wheel bearings Check blade drive V belt tension DO NOT over tension Change in sets only NOTE See engine manual for specific engine maintenance for your specific model SE aD SERVICE EVERY 50 HOURS 1 Replace engine oil and filter 2 Clean engine motor air fins 3 Lubricate depth control adjustment screw Screw Feed version only 4 Check wheels for wear or damage INDICATION INFORMATION MANDATORY INSTRUCTION A WARNING Q PROHIBITION These signs will give advice for your safety A Before leaving our factory every machine is thoroughly tested Follow our instructions strictly and your ma chine
19. ned only to suppress airborne concrete dust diamond blades with the water tank as the water source because there is not sufficient wa ter flow available to properly cool the blades WARNING DO NOT use conventional wet TIE DOWN BRACKET KIT P N 167189 A Tie Down Bracket Kit is available as a field installed accessory The kit consists of two 2 tie down loops that are installed at the front of the frame They are to be used only to SECURE the saw to a truck or trailer during transport WARNING DO NOT use the tie down brackets as a device for lifting the saw 15 12 Governor Speed It is critical that the Governor and throttle on all internal combustion engines be adjusted properly The engine speed is preset at the factory for the proper sawing speed It is NOT normally necessary to change this setting It should be periodically verified after the saw is placed into service To change the Governor setting refer to the engine manual WARNING Overspeeding the blade can result in blade breakage and or personal injury to the operator and bystanders To assure the proper Governor adjustment determine the correct blade shaft speed from the following chart Follow the engine manufacturer s instruction procedure for Governor and throttle setting NO LOAD BLADE SHAFT AND ENGINE R P M s BLADE SHAFT MODEL R P M 9H 14 18 13H 14 18 2610 2610 3600 3600 13 Repair We carry out all repairs in t
20. ont of Frame well ventilated areas Quantity 1 DO NOT operate near combustible material Always wear approved equipment Muffler Is HOT May Cause Burns And Or Ignition Of Material Avoid Contact P N 542169065 P N 177588 Location Engine Fuel Tank Location Top of Belt Guard Quantity 1 Quantity 1 MC 18 Specifications MC 18 9H MC 18 13H Se 13 HP 18 450 4 5 8 6 5 8 117 5 168 3mm 2 600 2600 209 95 222 101 182 83 195 88 1 25 4mm 4 1 2 dia with drive pin 3 V belts 9 amp 13 HP engine Spring assisted screw feed Removable dual water spray tubes water supply connector located on left side of saw control 3 4 19 mm diameter raises and lowers cutting head 5 x 1 1 2 x 3 4 102 x 38 x 19mm solid rubber tires cast iron hub roller bearings lube fitting 8 x 2 x 5 8 203 x 51 x 15 9mm ball bearings semi pneumatic tires One piece reinforced box base Honda Honda Gas Engine Gas Engine GX270 GX390 Max Horsepower 9HP 13 AP Displacement cu in cc 16 5 270 23 7 389 3 0 76 3 5 88 2 3 58 2 5 64 1 4 1 4 1 59 6 0 17205 2 3 1 1 2 3 1 1 Accessories Item No Dry type Dry type Tie Down Kit 167189 dual element dual element Outer Flange 1 2 cutting width 167963 w pre cleaner w pre cleaner Replacement Blade Wrench 163988 Recoil Recoil Water Tank Kit Standard saw 174957 Air Air Standard Standard SAW DIMENSIONS Inches mm Crated Dimension
21. rformance Follow instructions for changing accessories Inspect tool cords peri odically and if damaged have repaired by authorized service facility always give a copy of this manual to the equipment user If you need extra copies call TOLL FREE 1 800 288 5040 SAFETY FIRST WARNINGS DO s and DO NOT s WARNING FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY AA DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT DO NOT operate this machine unless you have read and understood this operator s manual operate this machine without the blade guard or other protective guards in place stand behind or in front of the blade path while the engine motor is running leave this machine unattended while the engine motor is running work on this machine while the engine motor is running operate this machine when you are tired or fatigued use a wet blade without adequate water supply to the blade exceed maximum blade speed shown for each blade size Excessive speed could result in blade breakage operate the machine if you are uncertain of how to run the machine use damaged equipment or blades touch or try to stop a moving blade with your hand cock jam wedge or twist the blade in a cut
22. s L 35 x H 30 1 2 x W 22 889 x 775 x 559mm Inches Metric mm A Height Max In mm 47 1 2 1207 B Saw Length Pointer Up 45 1 2 1156 C Max Saw Length Pointer Down amp Handles Out 64 1 4 1632 E Pointer Extension 18 3 4 476 16 406 22 1 2 572 22 10 1 4 J Rear Wheel Track 19 1 2 K Blade to Wall 2 3 8 L Wheel Base Length 15 Specifications are subject to change without notice SAFETY FIRST WARNINGS A DO s and DO NOT s WARNING FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY AS Do OLE DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO read this entire operator s manual before operating this machine Understand all warnings instructions and controls keep all guards in place and in good condition wear safety approved hearing eye head and respiratory protection read and understand all warnings and instructions on the machine read and understand the symbol definitions contained in this manual keep all parts of your body away from the blade and all other moving parts know how to stop the machine quickly in case of emergency turn the ON OFF switch to the OFF position prior to connecting the electric powered model to the power source inspect the blade flanges and shaft
23. s for damage before installing the blade use the blade flange size shown for each blade size use only steel center diamond blades manufactured for use on concrete saws use only reinforced abrasive blades or steel center diamond blades manufactured for use on concrete saws use only the blade flanges supplied with the saw Never use damaged or worn blade flanges use only blades marked with a maximum operating speed greater than the blade shaft speed Verify speed by checking blade shaft rem and pulley diameters verify saw drive configuration by checking blade shaft RPM pulley diameters and blade flange diameter read all safety materials and instructions that accompany any blade used with this machine inspect each blade carefully before using it If there are any signs of damage or unusual wear DO NOT USE THE BLADE mount the blade solidly and firmly Wrench tighten the arbor nut make sure the blade and flanges are clean and free of dirt and debris before mounting the blade on the saw use the correct blade for the type of work being done Check with blade manufacturer if you do not know if blade is correct use caution and follow the instructions when loading and unloading the machine operate this machine only in well ventilated areas instruct bystanders on where to stand while the machine is in operation establish a training program for all operators of this machine clear the work area of unnecessary people Never allow anyone to
24. stand in front of or behind the blade while the engine is running make sure the blade is not contacting anything before starting the engine use caution when lifting and transporting this machine always tie down the machine when transporting use caution and follow instructions when setting up or transporting the machine have all service performed by competent service personnel make sure electric powered machines are plugged into a properly grounded circuit make sure power cords are the proper size and in good condition verify the blade arbor hole matches the machine spindle before mounting the blade always check for buried electrical cables before sawing If unsure contact the local utilities clean the machine after each day s use follow all electrical codes in your area consider work area environment Don t expose power tools to rain Don t use power tools in wet locations use caution to guard against electric shock Prevent body contact with grounded surfaces i e pipes radiators ranges refrigerators use correct voltage and proper extension cords Never carry tool by cord or yank it to disconnect it from receptacle Keep cord away from heat oil and sharp edges always transport the machine with the motor stopped keep the handles dry clean and free of oil and dirt disconnect tools from power source when not in use before servicing and when changing accessories carefully maintain and clean for better and safer pe
25. utting generates dust that comes from the material being cut which frequently contains silica Silica is a basic component of sand quartz brick clay granite and numerous other minerals and rocks Exposure to excessive amount of such dust can cause e Respiratory diseases affecting your ability to breath including chronic bronchitis silicosis and pulmonary fibrosis from exposure to silica These diseases may be fatal e Skin irritation and rash and e Cancer according to NTP and IARC National Toxicology Program International Agency for Research on Cancer Take precautionary steps e Avoid inhalation of and skin contact with dust mist and fumes e Wet cut when feasible to minimize dust e Wear and ensure that all bystanders wear appropriate respiratory protection such as dust masks designed to filter out microscopic particles See OSHA 29 CFR Part 1910 1200 California Prop 65 Warning Use of this product can cause exposure to materials known to the State of California to cause cancer and or birth defects or other reproductive harm Husqvarna Printed in the USA
26. zado Diamond Blade Sierra Diamantada ae Blade Diameter Diametro De La Hoja ES Pulley Diameter Di metro De La Correa Number of Revolutions Per Minute Rotational Speed N De Revoluciones Por Minuto Velocidad De Rotaci n Blade Flange Diameter Di metro De La Brida De La Hoja Machine Mass lbs Masa De La Maquina lbs Engine Motor Engine Speed Revolutions Minute Velocidad Del Motor En Revoluciones Por Minuto RPM Engine Start Arranque Del Motor 9 Q OPEL HEARING HAZARD DURING NORMAL USE OF THIS MACHINE OPERATOR MAY BE EXPOSED TOA NOISE LEVEL EQUAL OR SUPERIOR TO 85 dB A RIESGO DE DANO AUDITIVO EN CONDICIONES NORMALES DE UTILIZACION EL OPERADOR DE ESTA MAQUINA PUEDE ESTAR EXPUESTO AUN NIVEL DE RUIDO IGUAL O SUPERIORA 85 dB A DECAL DESCRIPTIONS AND LOCATIONS DECRIPCION DE CALCAMONIAS Y UBICACIONES k Husavarna P N 542190733 Location Front of Frame Quantity 1 H Husavarna MC 18 Location Belt Guard Quantity 1 RAISE F ON 3 Turns 1 inch I approx STOP Read and understand the entire operators LOWER manual before using this machine P N 174998 Location Top of Screw Feed Bracket If you DO NOT have an Quantity 1 Operators Manual Call Toll Free 1 800 288 5040 Machinery Hazard SEE Always keep all guards in place GREASE BEARINGS DAILY Always Keep all parts of your body away from all moving parts P N 040563 Always use only in Location Fr
Download Pdf Manuals
Related Search