Huffy MQX-2150 User's Manual
Contents
1. not allow water in tank to freeze During sub freezing weather add non toxic antifreeze sand or empty tank completely and store Do not use salt Use extreme caution if placing system on sloped surface System may tip over more easily HUFFY SPORTS In the U S 1 800 558 5234 and Canada 1 800 284 8339 201241 2199 A SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Check entire box and inside all packing material for parts and or additional instruction material Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document Proper and complete assembly use and supervision are essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly If using a ladder during assembly use extreme caution Two 2 people are recommended for this operation e Check base regularly for leakage Slow leaks could cause system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during pla2. 211994B 05 03 12 SECTION B ASSEMBLE THE BOARD AND RIM This is what your system will look like when you ve finished this section EJ Item 19 12 Item 17 6 mv O Item 22 4 Item 21 4 B AE IM Item 23 2 13 05 03 P N 211994B Mount brackets 20 and rim 18 to backboard and finger tighten as shown NOTE Final adjustments will be made in Step 3 of this section IMPORTANT For spring loaded rim assembly refer to instructions included with rim hardware Refer To Instructions Included With Rim Hardware For Rim Assembly P N 211994B 05 03 14 Support pole and tank assembly over support table Carefully slide backboard components onto pole A WARNING AWARNING TWO PEOPLE DO NOT LEAVE REQUIRED FOR THIS ASSEMBLY PROCEDURE FAILURE UNATTENDED WHEN TO FOLLOW THIS EMPTY IT MAY TIP WARNING COULD OVER RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE SAWHORSE OR SUPPORT TABLE While still in the horizontal position carefully slide backboard components onto pole Secure hardware at desired position as shown and tighten all hardware completely at this time 15 05 03 P N 211994B Install clips A WARNING USE OF THIS PRODUCT WITHOUT PROPER CLIP ARM INSTALLATION OF SMART CLIPS OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM BE SURE TO FOLLOW DIRECTIONS CAREFULLY CLIP BODY Insert one arm of clip into ram as sho
3. HUFFY SPORTS Portable System Owners Manual Customer Service Center e N53 W24700 South Corporate Circle e Sussex WI 53089 U S A AW A R N N G gt lt TOOLS AND MATERIALS Wood Board Scrap Read and understand Tape Measure operator s manual before Step Ladder 8 ft 2 4 m using this unit Tape e Garden Hose or Sand 360 Ib 163 kg Hammer e Wrenches Two 1 2 One 9 16 or Two Small Adjustable Wrenches 9 16 Deep Socket property w Extension Recommended Support Table Failure to follow operating instructions could result in injury or damage to Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 555 85234 Sweden 009 555 85234 For Australia 1 800 333 061 Internet Address http www huffysports com 1 05 03 P N 211994B COPYRIGHT 2000 by HUFFY SPORTS P N 211994B 05 03 FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is com
4. Hex Head 5 16 18 x 3 3 4 Washer 5 16 Flat Tank Strut Lock Nut 5 16 18 Label Moving System and Height Adjust Bolt Hex Head 5 16 18 x 1 Long Nut Hex Flange 5 16 18 Rim SmartClip Net Holder Backboard Mounting Bracket Washer 1 O D Bolt Hex Flange 5 16 18 x 2 1 2 Long Bolt Carriage 5 16 18 x 3 1 2 Knob Plastic 1 3 4 Diameter Net Cap Tie Down Stake Spacer Wheel Axle T Strap Tank Cap YOU MAY HAVE EXTRA PARTS WITH THIS MODEL P N 211994B 05 03 HARDWARE IDENTIFIER PO Item 7 1 Oem ig Item 10 1 ih f N Item 11 1 O Item 12 6 Item 14 1 m Ol g Item 16 2 Item 17 6 Item 19 12 ae Item 22 4 DOO O f Item 23 2 Item 28 2 7 05 03 P N 211994B SECTION A ASSEMBLE THE BASE This is what your system will look like when you ve finished this section O 9 16 and 1 2 Item 7 1 OU AND OR a Item 11 1 Ol jm OF pe 2 Item 17 6 leen 214 9 16 and 1 2 Item 16 Item 12 6 Item 28 2 P N 211994B 05 03 8 Remove contents from tank Correctly identify each pole section and mark indicated distance from ends with tape not supplied as shown IMPORTANT Center the alignment slot of middle pole section 5 in the lower hole of top pole section 4 as shown While maintaining alignment bounce middle section of pole 5 into top section of pole 4 using w
5. ood scrap as shown until they no longer move toward taped reference mark NOTE Pole sections should have a 3 1 2 9 cm minimum overlap ALIGNMENT MARK 9 05 03 P N 211994B IMPORTANT Center the alignment slot of lower pole section 6 in the lower hole of middle pole section 4 as shown While maintaining alignment bounce top and middle pole assembly 4 amp 5 onto bottom section of pole 6 using wood scrap as shown until they no longer move toward taped reference mark NOTE Pole sections should have a 3 1 2 9 cm minimum overlap WOOD SCRAP P N 211994B 05 03 Q Install wheel axle 2 through wheel carriage 9 Install wheels 3 onto wheel axle 2 with spacers 28 as shown Insert pole assembly into tank assembly as shown Secure bottom pole 6 to tank and wheel bracket as shown A deep socket is recommended IMPORTANT DO NOT OVER TIGHTEN TWO PEOPLE REQUIRED FOR THIS PROCEDURE FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE THE SPACER 28 WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE Secure tank struts 13 to pole Rotate non secured ends of tank struts 13 outward to mounting holes in tank as shown A WARNING TIGHTEN BOLT 11 IN LOCK NUT 12 UNTIL FLUSH EVEN WITH LOCK NUT S OUTER EDGE 11 05 03 P N 211994B Secure non secured ends of tank struts 13 to tank as shown Repeat for opposite side P N
6. plete fill system completely with water or sand and stake to the ground Never leave system in an upright position without filling base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment See instruction manual for proper installation and maintenance When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do
7. s or Missing Parts DON T go back to store Call TOLL FREE Customer Service Number listed on the front page NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems including those used for DISPLAYS MUST be assembled and ballasted with sand or water according to instructions Failure to follow instructions could result in SERIOUS INJURY It is NOT acceptable to devise a makeshift weight system IMPORTANT Remove all contents from boxes Be sure to check inside pole sections hardware and additional parts are packed inside WARRANTY CARD Please remember to complete your product registration form either on line at www huffysports com warrantycard or mail in the enclosed postcard P N 211994B 05 03 4 BACKBOARD Sh Hoy NU ZZ AUS WY Ne STRUTS CARRIAGE ASSEMBLY 5 05 03 P N 211994B Item Qty Part No 206645 200628 226401 900060 908480 908490 202820 202822 200627 203063 201625 203218 906206 203220 200439 203156 203100 OOnNOOABRWN 201219 900057 203309 203113 203231 203435 206219 203124 201651 200629 203617 1 1 2 1 1 1 1 1 1 1 1 6 2 1 1 2 6 1 12 2 4 4 2 2 1 1 1 2 1 1 PARTS LIST See Hardware Identifier Description Tank Black Wheel Axle Wheel Top Pole Section Middle Pole Section with Label Bottom Pole Section Rod 3 8 O D x 4 3 4 Long Eye Bolt 3 8 x 16 x 3 3 4 Long Wheel Bracket Lock Nut Nylon Insert 3 8 16 Bolt
8. wn Twist body of clip slightly so that second arm slides over the top of the first arm as shown Push in direction indicated by arrows Push second arm back and into ram as shown Twist body of clip slightly again to spread arms of clip Clip arms must be flat and touching edge to edge as shown not overlapping P N 211994B 05 03 16 NET INSTALLATION Twist net until it snaps into position Net must be centered through clip 17 05 03 P N 211994B SECTION C APPLY HEIGHT AND MOVING LABEL amp SECURING SYSTEM Carefully upright assembly Apply moving system label 15 to front of pole as shown Regulation rim height is 10 feet 3 05 m TWO PEOPLE DO NOT LEAVE REQUIRED FOR THIS ASSEMBLY PROCEDURE FAILURE UNATTENDED WHEN TO FOLLOW THIS EMPTY IT MAY TIP WARNING COULD OVER RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Place assembled unit to desired location Fill tank with water 30 gallons 114 liters or sand 360 Ib 163 kg and snap tank cap 30 in place Insert T strap 29 through slot on back of base as shown Secure unit to ground by twisting tie down stake 27 into ground and hooking T strap 29 onto tie down stake 27 P N 211994B 05 03 18
9. y and or transport of the system e Climate corrosion or misuse could result in system failure Minimum operational height is 6 6 1 98 m to the bottom of backboard e This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown to the right e The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as pesticides herbicides or salts are all important If technical assistance is required contact Huffy Sports Adult supervision is recommended when adjusting height Most injuries are caused by misuse and or not following instructions Use caution when using this system HEIGHT ADJUSTMENT Rest unit on support table Remove adjustment knobs A and carriage bolts B to extend or retract backboard and rim Height adjustment from 7 1 2 to 10 AWARNING Backboard may rotate during height adjustment AWARNING Do not adjust height of system in upright position System must be in down position to adjust MOVING SYSTEM 1 While holding pole rotate basketball system forward until wheels engage with ground Move basketball system to desired location Carefully rotate basketball system upright Reattach ground restraint and check system for stability 200439 11 00 3 05 03 P N 211994B Question
Download Pdf Manuals
Related Search