Huffy AWLC6045 User's Manual
Contents
1. away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc Objects may entangle in net Surface beneath the base must be smooth and free of gravel or other sharp objects Punctures cause leakage and could cause system to tip over Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with exterior enamel paint If rust has penetrated through the steel anywhere replace pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before use Check system before each use for instability Do not use system during windy and or severe weather conditions system may tip over Place system in the storage position and or in an area protected from the wind and free from personal property and or overhead wires Never play on damaged equipment See instruction manual for proper installation and maintenance When moving system use caution to keep mechanism from shifting Keep pole top covered with cap at all times Do not allow water in tank to freeze During sub freezing weather add non toxic antifreeze sand or empty tank completely and store Do not use salt While moving system Do not allow anyone to stand or sit on base or have added ballasting on base Do2. quicker if you have your Model Number found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE TO ADJUST BACKBOARD While holding handle remove pin Move elevator up or down to desired height Replace pin full length to lock system at desired height Adjust basketball backboard height to lowest position Rotate handles forward until wheels engage ground Move basketball system to desired location Rotate handle back to original position Reattach ground restraint and check system for stability 201253 2 9 A WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on base and or pole After assembly is complete fill system completely with water or sand and stake to the ground Never leave system in an upright position without filling base with weight as system may tip over causing injuries When adjusting height or moving system keep hands and fingers
3. 918088 33 Aq 002 LHO9IHAdOO 0 L0 V6v6v Vc N d HUFFY SPORTS A Huffy Company WRITE IN YOUR MODEL NUMBER Customer Service Center N53 W24700 South Corporate Circle Sussex WI 53089 U S A Portable Basketball System with Elevator Owner s Manual SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated nside all packing material for parts Before beginning If using a ladder during assembly use extreme caution Two 2 people are recommended for this operation Check base regularly for leakage Slow leaks could cause system to tip over unexpectedly Seat the pole sections properly if applicable Failure to do so could allow the pole sections to separate during play and or transport of the system Climate corrosion or misuse could result in system failure Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NO
4. LLING SPRINGS Roll completed assembly to desired playing area Secure assembly 28 29 30 31 to ground using T Strap 45 and tie down stake 46 Fill tank with 34 gallons of water IMPORTANT Add two gallons 7 6 Liters of non toxic antifreeze in sub freezing climates WARNING DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY MAY TIP OVER While holding handle remove pin 60 Move elevator up or down to desired height Replace pin full length to lock system at desired height WARNING DO NOT ALLOW CHILDREN TO ADJUST HEIGHT Apply height and moving label 47 to front of pole as shown WARNING USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM BE SURE TO FOLLOW DIRECTIONS CAREFULLY Install net clips as shown See illustration Install net as shown See illustration Item Qty Part No 1 1 1 1 1 1 4 1 1 1 1 3 2 1 0 3 1 2 1 2 1 1 1 4 1 1 2 1 4 1 2 2 gt 904847 978482 900284 206615 226401 200628 202820 206934 206949 203063 906410 202541 203218 203100 203220 203798 206948 206252 203330 906606 900223 203103 206604 206940 206938 206605 204804 206956 900964 200874 205528 201642 206360 201124 PARTS LIST See Hardware Identifier Description Top Pole Section Black Middle Pole Section Black Bot
5. T excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 1 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as pesticides herbicides or salts are all important technical assistance is required contact Huffy Sports Adult supervision is recommended when adjusting height s are caused by misuse and or not followi Use caution when using 8 For more information on assembly placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com REQUIRED TOOLS AND MATERIALS Two People Tape Measure Wood Board Scrap Wrenches One 3 8 5 16 Two 7 16 1 2 9 16 3 4 or Large and Small Adjustable Wrenches Sawhorse or Support Table Step Ladder 8 ft 2 4 m Garden Hose or Sand 225 Ib 102 kg Hammer Tape Phillips Screwdriver Safety Goggles IMPORTANT In U S and Canada only Have questions don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free Customer Service Number listed below Service will be
6. ase Tank Plastic Anchor T Strap Stake Tie Down Label Height Adjustment and Moving Handle Left Handle Right Screw Phillips Head Height Adjustment Rod Label Height Indicator Bracket Pole Mount Carriage Bolt 5 16 18 x 3 1 2 Long Spacer Metal 1 2 O D x1 44 Long Spacer Biscuit Plastic Washer Metal 3 4 O D Cover Pin Slide Lanyard Black Coil Pin Locking Rim Net Wheel Carriage Spacer Plastic Wheel Axle Bracket Reinforcement Carriage Bolt 5 16 18 x 1 1 2 Long Lock Nut Hex Head 3 8 16 You may have extra parts with this model WARRANTY CARD Please remember to complete your product registration form either on line at www huffysports com warrantycard or mail in the enclosed postcard WARNING IF YOUR SYSTEM IS EQUIPPED WITH AN ACRYLIC BACKBOARD EXAMINE BACKBOARD FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT CRACKS IN THE BACKBOARD COULD RESULT IN SUDDEN BREAKAGE IF BACKBOARD IS DAMAGED IN ANY WAY PRIOR TO OR AFTER ASSEMBLY CALL TOLL FREE NUMBER FOR FREE REPLACEMENT U S 1 800 558 5234 CANADA 1 800 284 8339 http www huffysports com 5 01 03 P N 214949A IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL Questions or Missing Parts DONT go back to store Call TOLL FREE Customer Service Number listed on the front page P N 214949A 01 03 6 m 2 lt o ac O 65 I LL O lt Z O gt l
7. not leave system unsupervised or play on system when wheels are engaged for moving Use Caution when moving system across uneven surfaces System may tip over Use extreme caution if placing system on sloped surface System may tip over more easily HUFFY SPORTS In the U S 1 800 558 5234 and Canada 1 800 284 8339 201246 2 99 Toll Free Customer Service Number for U S 1 800 558 5234 For Canada 1 800 284 8339 For Europe 00 800 855 85234 Sweden 009 555 85234 For Australia 1 800 333 061 Internet Address http www huffysports com HARDWARE IDENTIFIER CONTINUED Item 7 1 N ys Item 10 3 th 13 10 Item 8 1 Item 12 1 QU Item 716 2 Item 14 13 Item 15 1 uma LL 7 Item 719 1 Item 718 2 Item 22 4 You may have extra parts with this model HARDWARE IDENTIFIER CONTINUED P N 214949A 01 03 2 HARDWARE IDENTIFIER C Emm C Item 30 2 nem s Item 432 4 TN tj Item 33 4 Item 34 5 Item 37 4 RI Item 39 0 43 12 Item 38 6 Item 36 6 11 2 Item 50 1 54 2 Item 55 2 Item 57 4 Item 64 2 You may have extra parts with this model 3 01 03 P N 214949A P N 214949A INSTRUCTIONS IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL Install wheel axle 6 th
8. rough wheel carriage 63 and install wheels 5 onto wheel axle 6 with spacers 64 as shown Secure wheel bracket as shown a deep socket is recommended IMPORTANT DO NOT OVER TIGHTEN Mark pole sections with tape as shown IMPORTANT Center alignment slot of middle pole section 2 in a lower hole of top pole section 1 as shown While maintaining alignment bounce pole top 1 and middle section 2 together as shown until they no longer move toward taped reference mark Upright assembly NOTE Pole sections should have a 3 1 2 9 cm minimum overlap IMPORTANT Center alignment slot of lower pole section 3 in a lower hole of middle pole section 2 as in step 3 While maintaining alignment bounce assembly and lower section 3 together as shown until they no longer move toward taped reference mark NOTE Pole sections should have a 3 1 2 9 cm minimum overlap Install rod 7 through holes in bottom pole section 3 and eyebolt 8 Insert pole assembly into tank assembly as shown Secure pole assembly with upper pivot bracket 9 and lock nut 10 IMPORTANT Two people recommended for this step Secure base struts 11 to pole using bolt 12 washers 13 and nut 15 as shown WARNING TIGHTEN BOLT 12 IN LOCK NUT 15 UNTIL FLUSH EVEN WITH LOCK NUT S OUTER EDGE Rotate the non secured ends of base struts 11 as shown Secure base struts 11 to base using bolt 16 washers 13 and nut 14 Insert carriage bolt
9. s 18 into middle set of holes on wheel bracket 21 as shown Attach lower pivot bracket 17 to wheel bracket using bolt 18 washers 13 disc 28 and nut 10 as shown Tighten completely Attach handle bar 20 to wheel bracket assembly using nuts 14 as shown Install wheels 3 onto axle 24 and wheel bracket assembly with push caps 25 as shown Attach wheel bracket assembly to base assembly using bolt 19 washers 13 and nut 10 as shown Carefully reposition entire assembly as shown Attach front of plastic handle 26 to back of plastic handle 23 around handle bar 20 using self tapping screws 27 as shown IMPORTANT Front of plastic handle 26 should face outward away from pole assembly Insert bolts 66 through plastic handle assembly handle bar 20 and attach nuts 14 as shown Tighten completely IMPORTANT Two people recommended for this step Install pole mount bracket 53 with carriage bolts 54 as shown Tighten flange nuts 14 completely Attach spacers 55 56 to pole mount bracket 53 with bolts 33 washers 57 and nuts 34 as shown IMPORTANT Tighten until washers 57 no longer move Attach covers 58 onto pole mount bracket 53 with carriage bolt 39 and nut 14 as shown IMPORTANT Loop end of pin lanyard 59 over carriage bolt 39 during this assembly 01 03 NOTE Assemble lanyard 27 to locking pin 28 as shown Apply logo and height indica
10. t O a nc a z l O e a E a x O 6 WOOD SCRAP T a Ek OF 0 Note See Text Page MIDDLE See Text Page WOOD SCRAP 214949A 01 03 WARNING LABEL SIDE FRONT SIDE 214949A 01 03 8 IMPORTANT See Text Page IMPORTANT See Text Page Note See Text Page Note See Text Page 9 01 03 P N 214949A ELEVATOR INSTALLATION IMPORTANT For spring loaded rim assembly refer to instructions included with rim hardware P N 214949A 01 03 10 IMPORTANT SEE TEXT PAGE Note See Text Page AWARNING 2 See Text Page a ay Q 11 1 03 214949A HEIGHT ADJUSTMENT NOTE Peel protective film from surface of acrylic backboard prior to use P N 214949A 01 03 12 e Install net clips WARNING Use of this product without proper installation of net clips or when all net clips are not present could result in bodily harm Be sure to follow directions carefully CLIP CLIP BODY Insert one arm of clip into ram as shown Twist body of clip slightly so that second arm slides over the top of the first arm as shown Push in direction indicated by arrows Push second arm back and into ram as shown Twist body of clip slightly again to spread arms of clip Clip arms mus
11. t be flat and touching edge to edge as shown not overlapping 13 01 03 P N 214949A NET INSTALLATION SIDE VIEW Insert net into bottom of clip as shown Twist net until it snaps into position Net must be centered through clip P N 214949A 01 03 14
12. tom Pole Section Black Base Wheel Wheel Axle 11 3 4 Long Rod 3 8 x 4 3 4 Long Eyebolt Pivot Bracket Upper Lock Nut 3 8 16 Nylon Insert Base Strut Black Bolt Hex Head 5 16 18 x 3 3 4 Long Washer Flat 3 8 1 D Nut Hex Flange 5 16 18 Lock Nut 5 16 18 Nylon Insert Bolt Hex Flange 5 16 18 x 1 1 2 Long Pivot Bracket Lower Bolt Hex Head 3 8 16 x 1 Long Bolt Hex Head 3 8 16 x 4 1 2 Long Handle Bar Wheel Bracket Carriage Bolt 5 16 18 x 2 Long Handle Back Plastic Axle Push Cap Handle Front Plastic Screw Phillips Head 3 4 Long Disc 5 O D x 13 32 I D Plastic Bracket Elevator Mount Spacer Steel 402 1 0 50 O D x1 5 Long Bolt Hex Flange 5 16 18 x 1 Long Spacer 530 1 x 63 O D x 63 Long Bolt Hex Head 3 8 16 x 2 5 8 Long Item Qty Part No 904821 206304 206311 206340 203038 904808 202814 204837 201219 203617 201568 203124 201253 204855 204856 204803 904833 204872 204832 203231 204857 204858 220154 204859 204853 204850 200627 201651 206990 203217 gt 3 gt Description Elevator Tubes Lower Long Bolt Hex Head 1 2 13 x 6 5 16 Long Spacer Plastic 530 1 0 x 50 Long Lock Nut Hex Head 1 2 13 Carriage Bolt 5 16 18 x 2 3 4 Long Elevator Tube Upper Short Cap Pole Top Spring Smart Clip Net Holder Cap B
13. tor labels 52 to adjustment rod 51 as shown Attach handle parts 48 49 to adjustment rod 51 with screw 50 carriage bolts 22 and flange nuts 14 as shown NOTE Holes in adjustment rod allow for either rear access or side access Insert handle assembly through pole mount assembly as shown Lock pole assembly in place at the 10 3 05 m mark with pin 60 Attach backboard support brackets 29 to the backboard frame using bolts 33 spacers 30 and nuts 34 as shown Attach lower elevator tubes 35 and spring 42 to backboard support brackets 29 using spacers 32 bolt 36 and nut 38 as shown NOTE Rim mounting nuts and bolts 31 supplied with rim hardware Attach upper elevator tubes 40 to backboard support brackets 29 using spacers 32 bolt 36 and nut 38 as shown Support pole on sawhorse Attach backboard assembly to top pole section 1 Install pole cap 41 IMPORTANT Two people recommended for this step Use caution elevator assembly is heavy Install handle assembly to lower elevator tubes 35 using bolt 36 spacers 37 and nut 38 NOTE Before going onto the next step set adjustment system to the 10 3 05m setting Insert bolt 36 through the left side upper elevator tube 40 then stretch spring 42 onto bolt 36 Insert bolt 36 through the right side upper elevator tube 40 and secure with nut 38 WARNING USE EYE PROTECTION WHEN INSTA
Download Pdf Manuals
Related Search