Huffy AC4052 User's Manual
Contents
1. 2 Item 43 1 O Item 41 1 E Item 44 1 E O Item 45 1 CO Item 46 1 P N 211560H 01 03 182. system failure If technical assistance is required contact Huffy Sports Minimum operational height is 6 6 1 98 m to the bottom of backboard This equipment is intended for home recreational use only and NOT excessive competitive play Read and understand the warning label affixed to pole Label is shown on page 2 The life of your basketball pole depends on many conditions The climate placement of the pole the location of the pole exposure to corrosives such as REQUIRED TOOLS AND pesticides herbicides or salts are all important MATERIALS Adult supervision is recommended when adjusting height Serious injury could occur if teeth face come in contact with backboard net or rim Three People Tape Measure Shovel and Post Hole Digger Use caution when using this system Carpenter s Level Two Step Ladder 8 ft 2 4 m Wrenches Two 1 2 9 16 3 4 One 3 8 Marker Vice For more information on assembly placement proper use and maintenance visit The American Basketball Council website at http www smarthoops com IMPORTANT Have any questions Don t go back to the store We appreciate your purchasing one of our many fine products We are sure that you will be very satisfied with your selection Although great care and effort have been taken occasionally problems may occur To ensure prompt and correct handling of any problems or to answer any questions please contact our Toll Free Customer Service Number list
3. Clean off any excess cement on mounting plate at this time PLAYING SURFACE NOTE Check leveling of mounting plate 3 several times while concrete is curing IMPORTANT Front of mounting plate 3 must be parallel with playing surface A WARNING DO NOT PROCEED TO STEP 6 UNTIL CONCRETE HAS CURED FOR A MINIMUM OF 72 HOURS ALLOW ADDITIONAL TIME FOR COLD WET OR HUMID WEATHER P N 211560H 01 03 4 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Upright pole 5 Assemble lower pole flange onto protruding J bolts 1 as shown The flange will then rest on the nuts 2 from Step 2 IMPORTANT Holes in pole must be parallel with playing surface PLAYING SURFACE Secure pole 5 flange to mounting plate 3 as shown Tighten completely ZQ PLAYING SURFACE 01 03 P N 211560H Insert caps 8 into end of each support arm 9 amp 10 as shown Tap firmly in position AWAR N NG TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Apply logo label 11 to lower support arms 10 as shown Repeat for opposite side Beginning with upper support arms 9 secure support arms to pole Continue by securing lower SHORT END IMPORTANT Do not over tighten support arms 10 as shown Note This bolt r
4. Customer Service Center Vv N53 W24700 South Corporate Circle E Sussex WI 53089 U S A A Huffy Sports Company WRITE IN YOUR MODEL NUMBER sd In Ground Basketball System Owners Manual 4 SAFETY INSTRUCTIONS A FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY PROPERTY DAMAGE AND WILL VOID WARRANTY Owner must ensure that all players know and follow these rules for safe operation of the system To ensure safety do not attempt to assemble this system without following the instructions carefully Proper and complete assembly use and supervision is essential for proper operation and to reduce the risk of accident or injury A high probability of serious injury exists if this system is not installed maintained and operated properly Check entire box and inside all packing material for parts and or additional instructional material Before beginning assembly read the instructions and identify parts using the hardware identifier and parts list in this document If using a ladder during assembly use extreme caution Two 2 people are reccomended for this operation Seat the pole sections properly Failure to do so could allow the pole sections to separate during play Before digging contact utility company to locate underground power cables gas and water lines Ensure there are no overhead power lines within 20 ft 7 m radius of pole location Climate corrosion excessive use or misuse could result in
5. ame 36 206685 Foam Roll 37 206681 Foam Pad 4 x 28 38 202856 Bolt Hex Head 1 2 13 x 4 39 908058 Bracket Jack Support Left 40 906276 Bracket Jack Support Right 41 220048 Bolt Hex Flange 1 2 13 x 6 42 222880 Crank Jack 43 206311 Spacer Black 53 x 1 2 44 203113 Bolt Hex Flange 5 16 18 x 2 1 2 45 203100 Nut Hex Flange 5 16 18 46 203218 Washer Flat 5 16 x 7 8 O D 920263 Rim Orange 201611 Bolt Hex Flange 5 16 18 x 3 203232 Washer 3 4 O D 200484 Spring 200323 Washer Large Concave 201124 Nut Hex Locking 5 16 18 920043 Cover Plate Orange 220140 Screw Self Tapping 1 4 20 x 1 2 220569 Label Logo Circle 204282 Net 220565 Label Height Indicator 206555 Pole Pad May Not Be Included 200685 Label Height Adjustment 200517 Bolt Covers 920262 Bracket Orange 920038 Inner Bracket Black 220065 Bolt Carriage 3 8 x 5 1 2 203063 Nut Hex Nylon Locking 3 8 203017 Nut Hex 3 8 203439 Bolt Hex 3 8 x 6 220064 Spacer 5 x 1 2 O D 206269 Spacer Zinc 75 x 4 I OO eres ONANAQASNRBPASABNNNO You May Have Extra Parts With This Model HARDWARE IDENTIFIER AS w Item 7 11 Item 4 34 Item 16 4 Item 19 3 Item 21 2 Item 26 4 Item 29 1 17 01 03 P N 211560H HARDWARE IDENTIFIER DX A AS iy P J H lt A CL UU Item 23 8 Item 24 8 Item 27 5 Item 30 1 f A 7 Y PS u O Q Item 32 2 Item 42
6. ed below Service will be quicker if you have your Model Number found on carton and assembly instructions ready when calling PLEASE WRITE YOUR MODEL NUMBER IN THE SPACE PROVIDED ABOVE Toll Free Customer Service Number for U S 1 800 558 5234 Internet Address http www hydra rib com COPYRIGHT 2002 by HUFFY SPORTS 1 01 03 P N 211560H IMPORTANT WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND OR PROPERTY DAMAGE Owner must ensure that all players know and follow these rules for safe operation of the system See instruction manual for proper installation DO NOT HANG on the rim or any part of the system including backboard support braces or net During play especially when performing dunk type activities keep player s face away from the backboard rim and net Serious injury could occur if teeth face come in contact with backboard rim or net Do not slide climb shake or play on pole When adjusting height keep hands and fingers away from moving parts Do not allow children to move or adjust system During play do not wear jewelry rings watches necklaces etc objects may entangle in net Keep organic material away from pole base Grass litter etc could cause corrosion and or deterioration Check pole system for signs of corrosion rust pitting chipping and repaint with with exterior enamel paint If rust has penetrated thro
7. en backboard frame nuts 23 completely P N 211560H 01 03 12 20 Insert spacer 45 through rim assembly 25 Place rim assembly on bracket 39 so that carriage bolt 41 is inserted through hole on top of inner bracket 40 Install hex bolt 44 washers 27 and nut 42 through top holes on bracket 39 through spacer 45 as shown Tighten completely BOTTOM VIEW Install rubber grommet 28 concave washer 29 and center lock nut 30 to carriage bolt 41 as shown Do not over tighten as rim will not flex properly See leveling instructions to determine how much to tighten nuts 42 and 30 13 01 03 P N 211560H LEVELING INSTRUCTIONS Place level on rim 25 and adjust nut 42 until level Tighten nut 30 to set rim tension for playing Apply logo label 33 to cover plate 31 Install cover plate 18 on rim 25 using self tapping screws 32 as shown NOTE ORIENTATION OF COVER PLATE Secure net 34 to NOTE Official rim height is rim 25 10 3 05 m from top of rim to playing surface 10 feet 3 05 m P N 211560H 01 03 14 Check leveling at this time Pole should be level in all directions NOTE If adjustment is necessary adjust system by rota
8. ests outside the ight pole Sms upright pole Mm OR P N 211560H 01 03 6 1 Cut foam stripping 14 to sizes shown and attach to flat side of H frame 13 as shown Then secure H frame to support arms 9 amp 10 NOTE Install H Frame 13 with foam striping toward backboard AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE IMPORTANT Do not over tighten 7 01 03 P N 211560H 12 Secure jack brackets 17 amp 18 to lower holes in pole as shown IMPORTANT HOLD HERE Position U joint of crank jack 20 as shown Where tubes on crank jack join hold steady to keep both tubes from rotating Rotate handle clockwise on crank jack to the fully extended position Upright crank jack P N 211560H 01 03 8 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Install crank jack 20 U joint to lower set of support arms 10 as shown 9 01 03 P N 211560H P N 211560H 01 03 5 AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Rota
9. te jack handle clockwise to raise H frame 13 to approximately 7 2 1 m from ground Secure crank jack 20 to jack brackets 17 amp 18 as shown NOTE Some adjustment will be necessary to align the lower crank jack bushing to jack brackets 17 amp 18 REAR VIEW 10 While H frame 13 is in the lowest position hang backboard onto H frame 13 NOTE Backboard frame will rest on top of H frame Secure backboard with hardware as shown ONLY Fingertighten bolts 22 with nuts 23 Repeat procedure for opposite side AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE 11 01 03 P N 211560H RIM ASSEMBLY amp INSTALLATION Install carriage bolt 41 through rim 25 washers 4 and 27 as shown Tighten nut 43 completely Place nut 42 about half way up carriage bolt 41 as shown AWARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND OR PROPERTY DAMAGE Attach bracket 39 to backboard and support structure by inserting bolts 26 and washers 24 through top holes in bracket 39 Tighten nuts 23 completely Insert inner bracket 40 into bracket 39 as shown Insert bolts 26 and washers 24 through top holes of inner bracket 40 as shown FROM STEP 13 Now tight
10. ting the nuts 2 between mounting plate 3 and pole flange Refered to in Step 6 After system is leveled completely tighten nuts 7 above pole flange Crank to achieve a rim height of 7 2 13 m from the ground Place a mark on pole at the point where the lower support arms intersect pole Center and apply the 7 2 13 m height line on label 35 on the mark and wrap around View height indicator label to determine approximate backboard height Apply height adjustment label 37 to front of pole as shown REGULATION RIM HEIGHT IS 10 FEET 3 05 m 15 01 03 P N 211560H Secure pole pad 36 as shown NOTE Pole pad may NOT be included in this model Height Adjustment Rotate crank handle to raise and lower backboard NOTE If height adjustment is difficult to operate you may have over tightened the areas indicated Refer to Step 10 and Step 14 P N 211560H 01 03 16 PARTS LIST PartNo Description Item Qty PartNo Description 206677 J Bolt 1 2 13 x 24 24 202459 Nut Hex 1 2 13 25 920578 Mounting Plate 26 203474 Washer Flat 1 2 x 1 O D 27 980830 Pole 28 220590 Pole Cap Square 29 206340 Nylon Insert Lock Nut Hex 1 2 13 30 220589 Cap Arm Support Insert 31 906658 Support Arm 42 Long Upper 32 906678 Support Arm 52 Long Lower 33 220586 Logo Label 15 x 1 3 4 34 220588 Bolt Hex Flange 1 2 13 x 9 35 906675 H Fr
11. ugh the steel anywhere replace the pole immediately Check system before each use for proper ballast loose hardware excessive wear and signs corrosion and repair before using Check system before each use for instability Never play on damaged equipment Keep pole top covered with cap at all times HYDRA RIB 1 800 558 5234 201255 2 99 Remove locking pin to remove Rotate crank handle to raise and lower backboard 200685 4 01 P N 211560H 01 03 2 Ensure ground is level with playing surface then dig pole hole PLAYING AWARNING ee BEFORE DIGGING GROUND SURFACE Install nut 2 to J bolt 1 as shown Repeat y 5 08 cm procedure for other three J bolts 1 IMPORTANT Make sure nuts are 2 5 08 cm from top of J Bolts G Install threaded ends of J bolts 1 through holes in mounting plate 3 and secure as shown NOTE Make sure J bolts 1 are in the illustrated position NOTE Nuts on the top of plate are used for leveling the pole after system is fully assembled 3 01 03 P N 211560H Fill hole with concrete Tamp down concrete to release air pockets and build drainage hill 5 Insert J bolts 1 from mounting plate 3 into cement as shown Move assembly around to release any air pockets in cement then rest mounting plate on cement drainage hill Apply some pressure to level mounting plate on top of drainage hill Level mounting plate and square with playing surface
Download Pdf Manuals
Related Search