Home

HP MSA30 Service and Maintain

image

Contents

1. Navigate to the component and check the status It should be Turn off the locate function by clicking Locate gt Locate Off Page 3
2. 1 Figure 4 and disconnect the power cord from the power supply A CAUTION When removing the left power supply ensure the cord lock on the right power supply is engaged This will avoid inadvertently disconnecting the right power supply Also take care to avoid disrupting the cables on the I O module to left of the power supply Page 2 2 Lift up on the wine colored mounting latch 2 then grasp the blower 3 and pull the power supply out of the enclosure 3 Remove the blower from the defective power supply and install it Retu rning the failed com ponent on the replacement power supply Follow the return instructions provided with the new component Figure 4 Removing a power supply Installing a power supply 1 Lift up on the module latch 1 Figure 5 and slide the power supply into the enclosure until it is fully seated 2 Connect the power cord to the power supply and engage the cord lock Figure 5 Installing a power supply Verifying proper operation After replacing the power supply or blower check the following to verify that the component is operating properly NOTE It may take up to 10 minutes for the component to display good status e Ensure the blower begins operating immediately e Verify that he status indicator is on e On an MSA1000 the controller LCD panel should no longer indicate a power supply blower failure From HP Command View EVA on an EVA product
3. HP s express limited warranty statement which may be viewed at hitp customerops corp hp com 1sw pdm_om warranty_support policies 2330100 doc The replacement part takes on either the Limited Warranty Period of the part being replaced or a ninety day period that begins upon installation of the replacement part whichever is greater The only warranty for this replacement product is as noted above Nothing in these replacement instructions should be construed as constituting an additional warranty The information provided in these replacement instructions is provided AS IS and HP is not liable for technical or editorial errors or omissions contained herein Before you begin Observe the following precautions when replacing the power supply blower You have only seven minutes to perform the replacement procedure Both power supplies must be installed for the enclosure to cool elas If a power supply fails leave it in place in the enclosure until a new power supply is available to install The enclosure could shut down due to overheating unless the power supply is replaced within seven minutes of removal of the failed failing power supply e If cabling is obstructing access to the power supply blower carefully move the cables out of the way to avoid loosening any connections e Parts can be damaged by electrostatic discharge Use proper anti static protection e Have a copy of the product user guide available for reference Y
4. HP StorageWorks Disk enclosure power supply blower replacement instructions These instructions apply to the MSA30 MSA1000 EVA3000 5000 and EVA4x00 6x00 8x00 product families The part may also be used in other HP products See the documentation for your product for detailed replacement instructions Copyright 2005 Hewlett Packard Development Company L P Fourth edition June 2007 The information in this document is subject to change without notice Printed in Puerto Rico www hp com 5697 679 0 About this document This document describes the procedure for replacing the power supply blower assembly in MSA30 MSA1000 EVA3000 5000 and EVA4x00 6x00 8x00 products amp NOTE Because this component is used in several products the drawings may reflect a different enclosure than the one you have The removal and replacement procedure is the same for each product Warranty information If the product in which this part is being replaced is still under HP warranty then the replacement part s referred to in these Replacement Instructions is provided under the terms and conditions of the Hewlett Packard Company Limited Warranty for that ae A copy of this Limited Warranty may be viewed at ttp h18006 www 1 hp com products storageworks warranty html If this is a trade sale part product out of warranty then the replacement part s referred to in these Replacement Instructions is provided under
5. ou can download a copy of the user guide from the product support page on the HP website Verifying component failure The power supply and blower are separately replaceable components Before replacing a power supply or blower use the following methods to verity component failure MSA products e Check the power supply blower status indicator Figure 1 It should e off e On the front of the MSA1000 use the controller display buttons to scroll through the messages displayed on the controller LCD panel and locate the following message 409 STORAGE BOX lt n gt POWER SUPPLY FAILED The lt n gt value in the message identifies which enclosure has the failed power supply Box 1 MSA enclosure e Box 2 Disk enclosure attached to Port A of the MSA e Box 3 Disk enclosure attached to Port B of the MSA EVA products A CAUTION If HP Command View EVA does not present a status consistent with the power supply blower status indicator or if either HP Command View EVA or your system monitoring tool indicates multiple hardware failures contact HP support for assistance http www hp com support e Analyze any failure messages received e Check status using HP Command View EVA 1 In the Navigation pane select Storage system gt Hardware gt Rack gt Disk enclosure 2 In the Content pane select the Power tab or the Cooling tab then the appropriate component 1 or 2 The Operational state sho
6. uld be Ki Failed 3 To nae identify the correct enclosure click Locate gt Locate On to flash the status indicators on the front of the disk enclosure e Check the power supply blower status indicator Figure 1 It should be off 1 Status indicator 2 Power supply blower 1 3 Power supply blower 2 Figure 1 Power supply blower status indicator Removing a blower It is not necessary to remove the power supply to replace a failed blower A WARNING The blower motor does not stop immediately when the blower is removed Keep your fingers away from the blower blades until the motor stops While pushing in on the two wine colored mounting tabs 1 Figure 2 pull the blower 2 away from the power supply 0007e Figure 2 Removing a blower Installing a blower A CAUTION Pressing on the center section of the blower can damage the blades or the housing Only press on the outer edge of the blower when installing it 1 Align the blower guide post 2 Figure 3 with the mounting hole next to the power supply connector 1 2 Slide the blower onto the power supply 4 until the mounting tabs 3 snap into place 0008a Figure 3 Installing a blower Removing a power supply A CAUTION When a power supply is removed the enclosure could shut down due to overheating within seven minutes unless the power supply is replaced 1 Disengage the power cord lock

Download Pdf Manuals

image

Related Search

Related Contents

RANGER 7600 DOWNLOADABLE CONTROL  DVRMFC - User Manual  Tecnoware FAVPRE3 uninterruptible power supply (UPS)  Bedienungsanleitung de Operating instructions en Mode d  薬食発第0622004号 - 医療機器基準等情報提供ホームページ  Sagab by Elma Volt Stick Bright SEFRAM 12  BT-AG型 多孔制御バタフライ弁取扱説明書(H  

Copyright © All rights reserved.
Failed to retrieve file