Hoover S2200 User's Manual
Contents
1. Owner s Manual Legacy Supreme Vacuum Cleaner Read this Manual before Operating cleaner Fill in and retain The HOOVER vacuum cleaner you have just purchased is designed for carpet and rug cleaning and has cleaning tools for other tasks The model and serial number are located on the bottom of the cleaner For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your Hoover product Save Index Assembling Cleanetr 3 11 Cleaner Description 12 Cleaning Effetiveness Per Amp Rating 2 8 Energy Saving Tips 27 How To Use Cleaning Tools 16 18 Upright Cleaner 13 16 If You Have a Problem 26 Important Safeguards EE E 2 Lubrication 26 Maintenance Authorized Service I Taped ds 27 Replacing Agitator Brush Roll 24 25 Replacing Bel 21 23 U Replacing Headlight 20 21 L Replacing Paper Bag 18 192. Unpacking Cleanetr ii a 3 Warranty 29 1993 The Hoover Company Important Safeguards When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE To reduce the risk of fire electric shock Warnin E injury uce the risk of fire electric shock or Do not use outdoors or on wet surfaces Close supervision is necessary when any appliance Is used by or near children Do not allow vacuum cleaner to be ueed as a toy or to run unattended at any time Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and any other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Do not pick up anything that is burning or smoking such as ciga rettes matches or hot ashes Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner and the bag Unplug cleaner when not in use Turn off all controls before unplugging Always disconnect cord from electric
3. Power Drive belt 160147AG convertible Decade 80 Decade 800 Agitator belt 049258AG Elite Legacy Agitator belt 38528027 1 115 Friction fit extension wand 38634074 1 195 TOTAL MERCHANDISE ADD YOUR APPLICABLE STATE TAX TOTAL COST Au a a alele Check or Money Order payable to The Hoover Company Q Visa Q MasterCard Card Number_ F K OU Vy o f jf le Name on Card o o o oo y Exp Datte __ _ Signature Required Daytime Phone amp Area Code Use this f amp m to order HOOVER disposable bags belts bulbs spare tools and air freshener tablets directly from THE HOOVER COMPANY NORTH CANTON OHIO These items will be shipped to your home freight prepaid They may also be purchased from your local Hoover dealer or Hoover Factory Service Center See your Yellow Pages for listings Please detach order form and enclose with your check money order or credit card information Mail in orders limited to U S residents only VI CG rev lt V3O2 YIN rva jSedepNns 1ool J je 10 yBnoue seoujd 49801 o piey esoup lle ayes J A SI zzou xnj q 10 JUBIUSAUCS HB S9l10SS9959V g Butug l5 pe ui Ao 104 yBnoua 1617 e dous 10 189 OY UJ SN 10 109H d e 7 snou ay S1 8 S N Z 2 L punoye je BujuBajd 10 10 9Ji9d Bulug o 10 9218 14B oy ISN e fai iug 9 ol p u no aJeyM Ob IIIA J mod ziIs Iinj YM 19up 9l5o5 sodind ninui siyL eer en Aajsiueyg ped
4. 5 amp 6 Pull cord tight 5 Attach tool rack With sides marked FRONT facing forward hold tool rack and handle side by side Attach upper hook of rack onto Align the two hooks on rack with notch A of handle and lower hook notches at A and B on handle as onto notch B of handle Fig 8 shown Fig 7 BACK OF HANDLE Holding tool rack in place turn handle over and align screw holes Fig 9 Insert small screw and tighten securely Extra effort may be required STEP 3 Attach bag compartment Pull bag door latch forward and remove door Set bag door aside Fig 10 Note round opening and hooks on back of bag compartment Place opening over dirt tube and align hooks with slots in handle Press firmly to snap hooks into handle Fig 11 Note location of tapered rails on bracket and on lower handle Fig 12 Slide rails on bracket onto rails on lower handle until it snaps in place Pull bracket toward bottom of handle slightly to make sure bracket is locked in place Fig 13 RAILS lt STEP 4 Attach paper bag Align opening in paper bag with dirt tube Fig 14 Push paper bag collar firmly onto tube Fig 15 Fold top of bag under top of compartment To replace bag door lift up lower edge of paper bag and insert the 3 tabs on bottom of bag door into the 3 slots on bag compartment Fig 16 Make sure all edges of paper bag are completely inside the bag co
5. Headlight 4 Remove agitator and broken belt 22 5 Slip agitator through new belt with lettering toward outside of cleaner Lower end of belt into opening in cleaner body reposition agitator 6 Place the three tabs on bottom plate into slots in front of cleaner body Snap bottom plate into place over agitator 7 Turn cleaner over and stretch new belt onto motor pulley Extra effort may be required to stretch belt onto pulley Turn agitator making sure belt is not pinched between agitator and cleaner body The belt must rotate freely inside the belt guide If agitator does not turn remove bottom plate and reposition belt in belt guide 8 Replace hood and nozzle control knob 23 Agitator brush roll When to replace Disconnect cleaner from electri cal outiet and detach hose from cleaner When agitator brushes are worn the brush roll should be replaced To check condition of brushes move edge of card across bottom plate while turning agitator To maintain cleaning effectiveness replace brush roll if brushes do not touch card What to buy The brush roll may be replaced with either a single or double brush roll Single row of brushes Hoover part No 48414 033 Double row of brushes Hoover part No 48414 032 How to replace Disconnect cleaner from electri cai outiet and detach hose from cleaner 1 Remove bottom plate as de scribed in The belt section Remove a
6. USA 5651 I 398 I
7. back of rack as shown Fig 23 Open tool cover some models only Position dusting brush A furni ture nozzle B crevice tool C and extra belt D into side of rac as shown Fig 24 CAUTION When cleaner is turned on the agitator brush roll will continue to rotate when cleaner handle is in upright position Avoid tipping cleaner or setting It on furniture fringed area rugs or carpeted stairs during tool use To insert air freshener tablet see instructions on page 15 11 The assembled cleaner will look like the drawing below Operate cleaner only at voltage specified on data plate on bottom of cleaner Cleaner description 1 Handle 2 ON OFF switch 3 Cord hooks wrap cord around hooks for storage The top hook can be rotated right or left for easy cord release 4 Bag door latch 5 Bag door 6 Stair cleaning handle located on lower edge of bag compartment 7 Handle release lever step on lever to lower handle to operating or low position 6 Cleaner body 9 Nozzle control knob slide knob to correct setting for height of carpet being cleaned or for clean ing tools 10 Furniture guard helps prevent Cleaner from marking furniture 11 Headlight 12 Hood 13 Hose door open door to connect hose to cleaner 14 Hose 15 Extra Belt 16 Crevice tool 17 Furniture nozzle 18 Dusting brush 19 Tool cover 20 Tool rack 21 Wands 22 Bag compartment 23 Air fre
8. nozzle and use only forward strokes Edge cleaning Edge cleaning is provided on both sides of nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or lurniture Air freshener dispenser Lift drawer in the top of bag compartment and insert the air freshener tablet packed with cleaner Push drawer down into position The amount of fragrance released is regulated by sliding the control to one of three settings shown on top of bag compartment Air freshener tablets may be obtained from your local Authorized Hoover Dealer Depot a Hoover Factory Service Center or by using the mail order form in this owner s manual 15 Part No 58547 071 R15 Detach Order Form Here jt ee OREN a ine e quien Gi eii Teenie ss pas The Hoover Company Please complete this entire form 101 East Maple Street 04010001A 160147AG North Canton OH 44720 0 4010324A Q 049258AG Q 57363003 Q 38528027 No of items D 38528008 0 38634074 Ordered Please Print Your Name and Address carefully in Ink SHIP TO Please allow 3 to 4 weeks for delivery Name Street Ciy _ Sate zip PACKAGE No Cost No of NUMBER In Pack Per Pack Packs TOTAL Type A Disposable bags 4010001A 4010324A BreatheEasy MicroFiltration Type A Disposable bags 4010100A Air freshener tablets 57363003 50 Concept One PowerMAX Agitator belt 38528008
9. service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state or province If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 1 800 944 9200 In Canada contact Hoover Canada Burlington Ont L7R 4A8 1 800 263 6376 Questions amp Concerns The Hoover Company wants to quickly resolve any con cerns about your cleaner or u regarding its use However do not send your cleaner to The Hoover Com pany in North Canton for service This will only result in a elay If you are not completely satisfied look on the list pro vided with the product for your local Hoover Factory Ser vice Center or in the Yellow Pages under Vacuum Clean ers Household for the Authorized Warranty Service Dealer Depot nearest you or call 1 800 944 9200 U S only HOOVER and are registered trademarks THE HOOVER COMPANY NORIH CANTON OHIO 44720 RA 8 94 U5089 930 99 930 U5109 930 Litho
10. E CONTROL the nozzle for various carpet pile heights slide the nozzle control knob to the correct setting For ease in sliding knob the handle should be in the upright position The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position When using hose and tools slide knob to the Cleaning Tools setting Return knob to the correct setting when cleaning floors Do not leave knob in Cleaning Tools setting when cleaning floors Leave hose attached to cleaner and place other end firmly into tool rack for peak performance when Cleaning carpets For maximum cleaning performance the following carpet height settings are recommended e Setting 1 for low pile level loop kitchen type carpet e Setting 2 for other types of carpet Higher Settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance e Setting 5 for hose and cleaning tool use only Note If the cleaner is difficult to push slide the knob to the next higher setting 14 Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower
11. al outlet before servicing the cleaner Do not use without dust bag and or filters in place Change bag fre quently when picking up very fine materials such as powder Use extra care when cleaning on stairs Do not put any object Into openings Do not use with any opening a keep free of dust lint hair and anything that may reduce air ow Grasp the plug to disconnect from wall outlet to avoid damage to cord plug prongs or receptacle Never handle plug or appliance with wet hands e The use of an extension cord is not recommended e Do not use wtth damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot Use vacuum cleaner only for its intended use as described In the instructions Use only attachments recommended by The Hoover Company others may cause hazards Save these instructions 2 Unpacking Unpack the cleaner from the carton and identify the parts shown Remove and dispose of the cardboard packing A Upper handle B Lower handle cord Tool rack Tool rack screw Bracket Bag compartment Cleaner body L Handle bolt and nut One extra nut included J Paper bag K Air freshener tablet L Hose and cleaning tools M Wands N Extra belt Assembling cleaner It is extremely important to read and fol
12. ctiveness Per Amp Rating This is not an Amp rating Amps do not measure dirt removal only the amount of electricity used Cleaning Effectiveness Per Amp is determined by dividing this model s Cleaning Effectiveness by its Amps Cleaning Effectiveness is the percent value obtained from dividing a the geometric mean of the amount of embedded carpet dirt removed in testing under ASTM Test Method F608 89 by b the value 29 the geometric mean of the midpoints of the Dirt Pick Up Scales of ASTM F1411 Buyers Guide 28 Full One Year Warranty Domestic Use Your HOOVERe appliance is warranted in normal household use in accor dance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following Authorized Warranty Service outlets Proof of purchase will be required before
13. gitator from cleaner 2 Turn end plates of agitator in opposite directions until one end plate comes off Ca N JQ 24 3 Pull out shaft being careful to leave washer on shaft 4 Reinsert shaft to push out opposite agitator end 5 Repeat in other direction to push out second agitator end 6 Discard old agitator brush roll 7 Place agitator ends into new brush roll matching projections in roll with openings in ends Push ends firmly into place If bearing comes out of agitator end during disassembly place washer and bearing back into agitator end with white side of bearing out before inserting shaft 8 Insert shaft with washer into agitator Replace end plate and tighten Note Be sure shaft is inserted so that end plate with flat sided projection is secured onto belt end of agitator roll Use this illustration for reassembly if necessary Washer must be placed between agitator ends and bearing DISPOSABLE AGITATOR ROLL SLEEVE 9 Replace agitator and belt as shown in steps 4 8 of How to replace belt 25 AGITATOR ENO EN PO Tik Lubrication The motor is equipped with bearings which contain sufficient lubrication for the liie of the motor The addition of lubricant could cause damage Do not add lubricant to motor bearings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover War
14. ing clean air to the room Regular HOOVERe Type A disposable bags also fit Hoover your cleaner To assure that your cleaner pporates at peak performance it is imperative that you use only enuine HOOVER paper bags Gisributed by The oover Company HOOVER bags can be identi fied by these trademarks How to replace Disconnect cleaner from electri cal outlet Pull bag door latch forward and remove door from cleaner Grasp bag collar and pull collar from tube Note Do not clean out old bag and reuse Discard used bag Align opening in new paper bag with dirt tube in outer bag Push bag collar firmly onto tube Fold top of bag down under top of bag compartment To replace bag door lift up lower edge of paper bag Insert the 3 tabs on bottom of bag door into the 3 slots on bag compartment Make sure ail edges of paper bag are completely inside the bag compartment Close door 19 The headlight What to buy This cleaner uses a 12 volt wedge base type 912 bulb Hoover part No 27313 105 How to replace Disconnect cleaner from electri cai outlet and detach hose from cleaner 1 Remove nozzle control knob on front of hood by grasping knob and pulling up 2 Place handle in operating position and turn cleaner over Insert end of flat screwdriver into one of the four slots beside an arrow on bottom of cleaner 3 Pry outward to release latch Repeat to release latches at the remai
15. l may be used in tight spaces corners and along edges in 3 such places as dresser drawers 4 upholstered furniture stairs and baseboards 4 Wands are used to give extra length to your hose Attach them together or to any of the above tools C Attach wand and tools The toots are attached to the hose or the wand in the same manner Push tool firmly onto hose twist tool slightly to tighten or loosen connec tion Use tools with cleaner handle in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping cleaner or setting it on furniture fringed area rugs or carpeted stairs during tool use 17 Clearing obstructions To check for obstructions first turn cleaner off and disconnect from electrical outlet then disconnect hose from cleaner Open hose door and carefully remove any visible obstruction If no obstruction is found check hose and tools Remove obstruction To continue using tools reattach hose to cleaner If no obstruction is found and a problem persists contact your Hoover Factory Service Center or Authorized Warranty Service Dealer Depot How to clean tools To clean the hose wipe off dirt with a cloth dampened in a liquid detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using How to attach tool cover The tool cover is designed with a break a
16. low all instructions step by step when assembling your Legacys Supreme cleaner rOmmoo The assembled cleaner will look like this drawing If you need assistance with any step Of the assembly call The Hoover CO Consumer Response Center at 1 800 944 9200 This cleaner is intended for household use Side mounted hose trademark of The Hoover Company STEP 1 Assemble handle aT ROID SECTIONS LOWER HANDLE HANDLE Note The white switch look above the ON OFF switch on the upper handle holds the switch in the Off position and aids in proper assembly of your cleaner Assembly can be continued if the switch lock is missing However do not remove the switch lock until assembly is completed Place upper and lower handle sections on a flat surface aligning rod sections Push sections together firmly until they click and rod sections lock together Fig 1 Re careful not to press against the gray rod extending from the lower handle Fig 2 STEP 2 Attach cord ral NE lJ UPPER HANDLE Insert large rectangular end of cord into pocket in bottom of handle with side marked UP visible Fig 2 Make sure rectangular end is pushed into the handle as far as possible Slide cord protector toward upper handle Fig 2 ress cord into place at each of the three notches indicated Fig 3 UPPER HANDLE Press groove in cord protector into slot in handle Fig
17. mpartment Close door STEP 5 Attach handle With cord hooks to back place assembled handle onto handle base of cleaner body Fig 17 Rock handle side to side while pushing down firmly Extra pushing effort may be required Press the handle release lever to move handle to the operating or middle position Push bolt into hole on lower front of handle Fig 18 If bolt will not go through hole easily the bracket Is not locked and or handle is not pushed down completely Place nut in recessed area at back of handle Hold nut in place while tightening bolt securely with a screw driver Fig 19 Only one nut is needed on this model The extra nut is not required but has been provided for your convenience SWITCH LOCK ON OFF SWITCH Pull switch lock above ON Off switch straight out Fig 20 Dispose of switch lock Note If switch lock has come off during assembly make sure switch is in the OFF position down before plugging cord into electrical outlet Attach hose and tools With cleaner handle in lowest position open hose door and insert hose end with tabs into cleaner Turn hose end to lock in place Fig 21 To remove hose turn in opposite direction Stretch hose over tool rack and push opposite hose end firmly into cup in rack Fig 22 Note Hose ends must be firmly connected to cleaner base and tool rack when cleaning floors a gt Position wands in
18. ning three arrows 4 Turn cleaner over and lift off hood 20 5 Remove bulb by pulling straight out of socket push new bulb into socket until it locks in place 6 Place hood on cleaner body and press firmly to snap all four latches Pull up on hood slightly to make sure all four latches are secured Push nozzle control knob back onto front of cleaner The belt The belt on your HOOVER cleaner causes the agitator to rotate and is impor tant for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace To check belt remove bottom plate as shown on the following page under How to replace Replace belt if it is stretched cut or broken What to buy One extra belt has been provided with your cleaner To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for Hoover part No 38528427 21 How to replace Disconnect cleaner from electri cal outlet and detach hose from deaner 1 Place handle in operating position and turn cleaner over To remove bottom plate insert end of flat screwdriver into wide area of right hand slot and push handle of screwdriver to the rear Repeat in left hand slot 2 Rotate plate and remove from cleaner body 3 Remove hood as directed in steps l 4 of How to Replace
19. r or Authorized Hoover Warranty Service Dealer Depot where approved HOOVER service and genuine HOOVER replacement parts may be obtained Provided with this product is a listing of the Hoover Factory Service Centers If you are unable to obtain the information you need from the Yellow Pages contact a Hoover Factory Service Center to find your nearest Authorized Hoover Warranty Service Dealer Depot For service under warranty follow the instructions in the warranty provided with this product Do not send your cleaner to The Hoover Company in North Canton for service as this will only result in a delay Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 1 800 944 9200 In Canada contact Hoover Canada Burlington Ont L7R 4A8 1 800 263 6376 Energy saving tips 1 Replace paper bag promptly before it is overfilled Use a genuine HOOVER bag made for you cleaner 2 To maintain effective cleaning replace agitator brush roll and belt when necessary 3 Turn off cleaner when not in use such as when moving furniture 4 Keep your cleaner operating at peak performance have inspection and service performed by a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot 27 Cleaning Effe
20. ranty Service Dealer Depot If you have a problem This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory If a minor problem occurs it usually can be solved quite easily when the cause is found Therefore this check list is provided for your convenience Problem Possible cause Possible solution Cleaner 1 Not firmly plugged in I Plug unit in firmly won t 2 No voltage In wall plug 2 Check fuse or breaker run 3 Blown fuse tripped 3 Replace fuse reset breaker breaker Cleaner I Broken or worn belt L Replace belt won t 2 Agitator brush roll 2 Replace brush roll pick up worn 3 Bag full 3 Change paper bag 4 Incorrect carpet height 4 Move nozzle control setting knob to type of carpet being cleaned 5 Hose end notsecure In 5 Push hose end firmly tool rack into cup In tool rack Cleaning I Hose clogged I Remove hose and tools tools won t remove obstruction pick up 2 Incorrect setting 2 Move knob to Cleaning Tools Cleaner I Incorrect carpet height I Move nozzle control hard setting knob to a higher setting to push 26 Service if the problem persists check the Yellow Pages of your telephone book under Vacuum Cleaners Household for your nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot where approved HOOVER service and genuine HOOVER replacement parts may be obtained Provided with
21. shener dispenser designed to hold a fragrance tablet and release a pleasant scent during Cleaning 12 How to use To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit uy in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way To turn cleaner on push switch up To turn cleaner off push switch down Plug cord into electrical outlet Turn cleaner on and with handle in upright position pull back on handle until front of cleaner is lifted off the carpet This insures that the paper bag is inflated Hose end must be firmly pushed into cup in tool rack for maximum suction on floors Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle Transporting cleaner To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward The cleaner can also be moved by lifting it as shown 13 Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle If it is necessary to raise and lower NOZZL
22. this product is a listing of the Hoover Factory Service Centers If you are unable to obtain the information you need from the Yellow Pages contact a Hoover Factory Service Center to find your nearest Authorized Hoover Warranty Service Dealer Depot For service under warranty follow the instructions in the warranty provided with this product Do not send your cleaner to The Hoover Company in North Canton for service as this will only result in a delay Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 1 800 944 9200 In Canada contact Hoover Canada Burlington Ont L7R 4A8 1 800 263 6376 Energy saving tips 1 Replace paper bag promptly before it is overfilled Use a genuine HOOVER bag made for you cleaner 2 To maintain effective cleaning replace agitator brush roll and belt when necessary 3 Turn off cleaner when not in use such as when moving furniture 4 Keep your cleaner operating at peak performance have inspection and service performed by a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot 27 Service if the problem persists check the Yellow Pages of your telephone book under Vacuum Cleaners Household for your nearest Hoover Factory Service Cente
23. way feature which allows it to snap off if it is pushed open too far To reattach align hinges of cover with slots on side of tool rack Press cover back into place Maintenance The following sections are concerned with proper maintenance of the cleaner Familiarize yourself with these home maintenance tasks and keep this owner s manual in a convenient place where you can refer to it when needed Proper use and care of your cleaner will ensure continued cleaning effectiveness The bag When to replace Check bag from time to time It is recommended that you change the bag when dirt reaches the dotted line If more dirt than this accumulates your cleaner may not operate effectively CAUTION Very fine materials such as face powder cornstarch fireplace ashes or fireplace soot may seal the paper bag and may cause it to burst even though it is only partially full of dirt When cleaner is used to remove material of this nature change bag often 18 Where to buy Paper bags may be purchased from your local Authorized Hoover Dealer Depot or from a Hoover Factory Service Center or use the order form packed with your cleaner When ordering bags be sure to give the model number of your cleaner What to buy For improved cleaning effectiveness use only HOOVERe Breathe Easy Micro Filtration Type A disposable bags These bags are constructed with filter material which removes 99 9 of dust down to 5 microns and aids in return
24. wos PORTON ASAOOH POSITION 5 j Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating position place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and furniture nozzle for stair cleaning When using cleaning tools the agitator will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling use extra care if cleaner is placed on stairs Cleaning tools The cleaning tools allow you to do specific cleaning tasks and to clean hard to reach areas The tool set includes a hose wands crevice tool furniture nozzle and dusting brush A Move nozzle control knob Slide nozzle control knob to the Cleaning Tools setting to divert suction to hose and cleaning tools Return knob to floor setting when tool use is complete 16 B Select proper cleaning tool The cleaning tools have many uses Select the tool best suited for the cleaning task from the descriptions below 1 Dusting brush may be used for carved lurniture table tops books lamps lighting fixtures Venetian blinds baseboards shutters and registers 2 Furniture nozzle may be used for upholstered furniture draperies 2 tapestries mattresses clothing automobile interiors and carpeted 3 Crevice too
Download Pdf Manuals
Related Search