Harbor Freight Tools Hitch Mount Vise Plate Product manual
Contents
1. this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state Haul Master 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 1 888 866 57972. IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of
3. Owner s Manual amp Safety Instructions Save This Manual keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference ITEM 66260 Haul viaster HITCH MOUNT Visit our website at http www harborfreight com Email our technical support at productsupport harborfreight com REV 14b When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 888 866 5797 as soon as possible Copyright 2008 by Harbor Freight Tools All rights reserved z No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included SPECIFICATIONS ASSEMBLY REEE Read the ENTIRE IMPORTANT 7 7 8 L x 7 7 8W x 3 16 T SAFETY INFORMATION Vise Mounting Holes 1 7 8 L x 5 8
4. W 4 section at the beginning of this document including all text under subheadings IMPORTANT SAFETY therein before set up or use of this product _____ INFORMATION __ 1 Wear ANSI approved safety oo goggles and heavy duty work Assembly Precautions gloves during assembly and use Angled End of N Receiver Retaining Pin 5 1 Assemble only according to these instructions Improper assembly can create hazards Receiver Retaining 2 Fits any standard 2 hitch receiver Pin 5 Wear ANSI approved safety goggles and heavy duty work gloves during assembly and set up Hairpin 4 Keep assembly area clean and well lit Clip 2 Receiver Tube 1 Keep bystanders out of the Fig 1 area during assembly l 2 Pull out the Hairpin Clip 2 and slide out the Receiver Retaining Pin 5 6 Do not assemble when tired or when under the influence of drugs or medication Use Precautions 1 This product is NOT designed to pull tow or push 2 This product is not a toy Do not allow children to play with or near this item 3 Use as intended only Receiver Retaining 4 Inspect before every use do not use Fig 2 if parts are loose or damaged 3 Slide the Receiver Tube 1 into the vehicle s receiver with the flat side of the Vise Mount Plate facing up See Fig 3 5 Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freigh
5. is needed elsewhere for other tasks it can be left mounted on the Hitch Mount Vise Plate but remove the Vise Plate Vise from the vehicle before driving After use brush off and wipe down the Vise Plate To remove the Hitch Mount Vise Plate from the vehicle s receiver a Pull out the Hairpin Clip 2 that locks the Receiver Retaining Pin 5 in position b Slide the Receiver Retaining Pin back out Slide the Hitch Mount Vise Plate out of and away from the vehicle s receiver Reinstall the Receiver Retaining Pin and slide the Hairpin Clip back so they do not become lost Store this Vise in a clean dry location away from children MAINTENANCE REPAIR Maintenance The Hitch Mount Vise Plate needs no maintenance other than brushing off and wiping down after use a Clean off any chips oil grease dirt or other debris Repair Before use a quick check is recommended to see if there are cracks or bent parts Page 3 PARTS LIST Qty Mounting Bolt M10 x 1 50 x 40mm Flat Washer M10 3 Vise Mount Plate Receiver Retaining Pin Lock Nut M10 x 1 50 4 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
6. t Tools for a replacement Page 2 For technical questions please call 1 888 866 5797 Item 66260 Item 66260 Align the holes in the Receiver Tube with those in the vehicle s receiver Insert the Receiver Retaining Pin through the holes in both the Receiver Tube and vehicle s receiver and out the other side a Replace the Hairpin Clip b Vise can be mounted before or after this step Mounting the Vise Remove the four bolts from the Vise Mounting Plate 3 unless the vise is already mounted See Fig 3 Put the 6 vise or any size vise with mounting holes that align properly with the Vise Mounting Holes 4 on top of the Vise Mount Plate 3 in the desired orientation Vise Mount Mounting Bolts 6 Plate 3 Vise Mounting Holes 4 Fig 3 Align up the holes in the vise with those in the Vise Mounting Plate See Fig 3 Secure the vise to the Vise Mount Plate 3 a Slide a Flat Washer 7 onto a Mounting Bolt 6 b Drop the Bolt Washer assembly down through the hole in the vise and through the Vise Mounting Hole 4 c From below the Vice Mount Plate 3 slide on another Flat Washer 7 and screw a Lock Nut 8 onto the bolt 10 11 1 For technical questions please call 1 888 866 5797 d Repeat for the three remaining Mounting Bolts 6 With 17mm wrenches or other appropriate tools tighten the Mounting Bolts 6 and Lock Nuts 8 securely Unless the Vise
Download Pdf Manuals
Related Search