Harbor Freight Tools 94137 User's Manual
Contents
1. LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 94137 For technical questions please call 1 800 444 3353 PAGE 32. 12 from center of Light to center of Light After the Lights are mounted use wire nut connectors not included to connect all three leads together Then connect to the Brown wire in the back of one Tail Light either side provided in this Kit ra Replacement parts and accessories When servicing use only idential replacement parts Only use accessories intended for use with this product 8 Z WARNING People with pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker WARNING The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator ASSEMBLY INSTRUCTIONS Vehicle Connection 1 Connect the BROWN B wire of the Color Coded Trunk Harness 4 to the towing vehicle s Tail Light wire Connect the YELLOW A wire of the Color Coded Trunk Harness to the vehicle s Left Hand Stop amp Turn light Connect the GREEN D wire of the Color Coded Trunk Harness to the vehicle s Right Hand Stop amp Turn light Make sure to use the BLUE Wire Splitter Connectors to make these connections See Illustration below 2 Attach the WHITE GROUND C wire to the towing veh
3. HAUL MASTER SUBMERSIBLE TRAILER LIGHT KIT Model 94137 Distributed Exclusively by a HARBOR FREIGHT in ic TOOLS mal 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS Copyrigh 2006 by Harbor Freight Tools All rights reserved No portion of this instruction sheet or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions please call 1 800 444 3353 PRODUCT SPECIFICATIONS item 12 Volt DC Negative Ground Design Type Submersible Design Features 2 Combination Class A Stop Tail Turn Lights License Plate Bracket 25 Ft Split Y Style Harness 4 Ft Color Coded Trunk Harness Light Type 18 LED s Per Light not serviceable DOT Approved Weight SAVE THIS INSTRUCTION SHEET You will need this instruction sheet for the safety warnings and precautions assembly instructions parts list and assembly diagram Keep your invoice with this instruction sheet Write the invoice number on the front of this instruction sheet Keep this instruction sheet and invoice in a safe and dry place for future reference UNPACKING When unpacking check to make sure all the parts shown on the Assembly Diagram are included If any parts are missing or broken please call Harbor Fr
4. ct the GREEN and BROWN wires to the right hand Stop Tail turn Light 1 with the Wire Nut Connectors included in the Mounting Hardware Package 5 See Assy Diagram 6 Attach the WHITE GROUND wire to the trailer tongue or frame See Assy Diagram T Connect the Split Y Style Harness 3 Plug to the Color Coded Trunk Harness 4 Plug See Assy Diagram 8 Turn on the towing vehicle s headlights The two Stop Turn Tail Lights 1 should turn on The brighter Stop Lights should turn on only when the vehicle s brake pedal is depressed or when the vehicle s turn signal is activated ignition key must be in its on position 9 If the Light Kit fails to illuminate check all ground connections If the turn signals on the Light Kit do not illuminate check the connections between the towing vehicle s wiring and the Color Coded Trunk Har ness 4 See Assy Diagram 5 MOUNTING HARDWARE NOT SHOWN Due to continuing improvements actual product may differ slightly from the product described herein Part Description Qty Part Description Qiy Stop Tail Turn Light Color Coded Trunk Harness License Plate Bracket Mounting Hardware 1 package Split Y Style Harness 1 o o oo o O NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS
5. eight Tools at the number above as soon as possible SAFETY WARNINGS AND PRECAUTIONS 1 Use eye protection Make sure to wear ANSI approved safety impact eye goggles when installing this Light Kit 2 Prior to installing this product make sure to read and understand all instructions and safety precau tions as outlined in the trailer camper etc manufacturer s manual onto which the Light Kit will be installed 2 Maintain the Light Kit Keep the Light Kit clean and dry for better and safer performance Make sure harness and all wiring remains properly attached to the trailer Make sure light covers are not cracked or damaged in any way always replace them if damaged 4 If necessary have a qualified service technician install the Light Kit Do not attempt to install this product yourself if you do not feel technically competent to do so 5 Use the right product for the job There are certain applications for which this product was designed Do not use small equipment or attachments to do the work of larger industrial equipment or attachments Do not use this product for a purpose for which it was not intended 6 If your trailer camper etc is OVER 80 wide You will need to install three additional Red Marker Lights not included onto the rear of the unit in order to comply with DOT standards To do so mount the three Red Marker Lights to the rear of the unit making sure the Lights are no less than 6 and no more than
6. icle s frame See Assy Diagram 3 NOTE If the towing vehicle has rear turn signals separated from its stop lights you will need to install additional hardware COLOR CODED TRUNK HARNESS 4 A YELLOW WIRE L H SIDE STOP TURN SIGNAL B BROWN WIRE TAIL LAMP MARKER CLEARANCE amp LICENSE C WHITE WIRE GROUND D GREEN WIRE R H SIDE STOP TURN SIGNAL SPLIT Y STYLE HARNESS 3 SKU 94137 For technical questions please call 1 800 444 3353 PAGE 2 Trailer Light Mounting And Connection 1 Mount the Stop Tail Turn Light 1 marked L H with the License Window on the left rear of the trailer with its side marker to the outside of the trailer Then mount the License Plate Bracket 2 with the Stop Tail Turn Light See Illustration on previous page 2 Mount the Stop Tail Turn Light 1 marked R H without the License Window on the right rear of the trailer with its side marker to the outside of the trailer See Assy Diagram 3 Use the Metal Frame Clips included in the Mounting Hardware Package 5 to mount each half of the Split Y Style Harness 3 down each side of the trailer Run the YELLOW and BROWN wires down the left side and GREEN and BROWN wires down the right side of the trailer See Assy Diagram 4 Connect the YELLOW and BROWN wires to the left hand Stop Tail turn Light 1 with the Wire Nut Connectors included in the Mounting Hardware Package 5 See Assy Diagram 5 Conne
Download Pdf Manuals
Related Search