Harbor Freight Tools 4832 User's Manual
Contents
1. pull Roller and Plates 13 up and out of Mill f Side Gear 7 6 Choose the correct Roller for the job i Bolt 11 amp T Remove Plates from end of Roller that was Washer 12 in the machine and install on the end of the chosen Roller Shaft Gear 10 8 Slide Plates and desired Roller back down into Mill body Attach the Side Gear Place the Cover back on the unit 9 Thread Bolt with Washer back into place on the body OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the A beginning of this manual including all text under subheadings therein before set up or use of this product 1 Choose the desired Roller The Mini Rolling Mill comes with five different Rollers two Smooth Rollers 15 two Fi 2 Pattern Rollers 17 and a Igurs Working Handle 2 Wire Roller 16 Choose the Roller with the pattern best Oil Reservoir 18 suited to your workpiece Operating Install as directed in the Handle 1 Assembly section of this Prani GRAILES manual 2 Fill the Oil Reservoir 18 with high quality light machine oil Bolt 11 amp Washer 12 Caution Keep hands clear of Gears and Rollers during operation The Gears and Rollers can cause injury REV 09a SKU 4832 For technical questions please call 1 800 444 3353 Page 5 2 Turning the Working Handle will raise or lower the top roller changing the amount of space between the Rollers This will also determine the de2. to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 3353 Record Product s Serial Number Here Note If product has no serial number record month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not avail able individually as replacement parts SKU 4832 For technical questions please call 1 800 444 3353 Page 8
3. CENTRAL MACHINERY MINI ROLLING MILL WITH 5 ROLLERS SET UP AND OPERATING INSTRUCTIONS a Diagrams within this manual may not be drawn proportionally Due to continuing improvements actual product may differ slightly from the product described herein Distributed exclusively by Harbor Freight Tools 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our website at http www harborfreight com Read this material before using this product Failure to do so can result in serious injury SAVE THIS MANUAL Copyright 2007 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 SAVE THIS MANUAL Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference WARNING Read all instructions Failure to follow all instructions listed below may result in serious injury SAVE THESE INSTRUCTIONS WORK AREA SAFETY q Keep children and bystanders away while operating Distractions can cause you to lose control 2 Keep w
4. OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 4832 For technical questions please call 1 800 444 3353 Page 6 PARTS LIST amp ASSEMBLY DIAGRAM Part Description Qty EAC e ever fr e sase f e manse r Parts Figure A Parts Figure B SKU 4832 For technical questions please call 1 800 444 3353 Page 7 LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase 90 days if used by a professional contractor or if used as rental equipment This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned
5. e For additional information regarding the parts listed in the following pages refer to the Assembly Diagram near the end of this manual Assembly iF Remove the protective plastic coverings from all items including the attached Rollers 2 Connect the Operating Handle 1 to the Shaft Gear 10 with Bolt 11 and Washer 12 as shown on the cover 3 Slide the Working Handle 2 between the Right and Left Screw Gears 4 5 into the hole on top of the unit Mounting 1 The Mill must be mounted before use Choose a work surface that is flat level and capable of bearing the weight of the Mill and workpieces 2 Operating Handle must be positioned to rotate freely 3 Using the Base of the Mill as a template mark with a pencil where the holes need to be drilled Verify that installation surface has no hidden utility lines before drilling 4 Drill holes in the work surface and mount the Mill firmly using appropriate hardware not included SKU 4832 For technical questions please call 1 800 444 3353 Page 4 Inserting Rollers 1 Remove the uppermost Bolt 11 and Washer 12 from Side Gear 7 2 Remove Side Gear located below Right Screw Gear 4 See Figure 1 3 Remove Left Screw Gear 5 and Right Screw Gear 4 from the Mill body by turning counterclockwise Figure 1 Pull Side Gear 7 from here 4 Remove all four Bolts 11 from Cover 6 of the Mill Pull Cover up and off 5 With the Cover off
6. ork area clean and well lit Cluttered or dark areas invite accidents PERSONAL SAFETY 1 Wear ANSl approved safety goggles NIOSH approved dust mask respirator and heavy duty work gloves during use and service 2 Stay alert and use common sense when operating Do not use when tired or under the influence of drugs alcohol or medication 3 Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts PRODUCT USE AND CARE 1 This product is not a toy Keep it out of reach of children 2 Use the correct product for your application The correct product will do the job better and safer at the rate for which it was designed Do not modify this product or use it for a purpose for which it is not intended 3 Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the product s operation If damaged have the product repaired before use 4 Use the product and accessories in accordance with these instructions and in the manner intended for the particular type of product taking into account SKU 4832 For technical questions please call 1 800 444 3353 Page 2 the working conditions and the work to be performed Use of the product for operations different from those intended could result in a hazardous situation SERVICE 1 Have product serviced by a qualified
7. pth of indentation that is made by the Roller 3 Insert the workpiece and turn the Operating Handle to pull it through the Rollers 4 Clean then store the product indoors out of children s reach MAINTENANCE AND SERVICING Damaged products can fail causing personal injury Do ACAUTION not use a damaged product If abnormal noise or vibration occurs have the problem corrected before further use Cleaning maintenance and lubrication 1 BEFORE EACH USE inspect the general condition of the product Check for loose screws misalignment or binding of moving parts cracked or broken parts and any other condition that may affect its safe operation 2 AFTER USE clean external surfaces of the product with clean moist cloth PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING
8. repair person using only identical replacement parts This will ensure that the safety of the product is maintained 2 Maintain labels and nameplates on the product These carry important safety information If unreadable or missing contact Harbor Freight Tools for a replacement MISCELLANEOUS 1 Keep hands clear of the gears and rollers of the Rolling Mill 2 Do not exceed the minimum or maximum gauge of wire or sheet stock listed for this product 3 The warnings precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS SKU 4832 For technical questions please call 1 800 444 3353 Page 3 SPECIFICATIONS Capacit Wire 031 to 197 pacity Sheet 35 Gauge to 079 3 1 Gear Ratio 2 Smooth Rollers Includes 1 Wire Roller 2 Pattern Rollers UNPACKING When unpacking check to make sure that the item is intact and undamaged If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SET UP INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the A beginning of this manual including all text under subheadings therein before set up or use of this product Not
Download Pdf Manuals
Related Search