Gefen EXT-HDMI1.3-1CAT6 User's Manual
Contents
1. OFF position The OFF position will use the LOCAL EDID mode The ON position sets the unit in PASSTHROUGH mode allowing the source to use the original EDID features of the display 4 Reconnect power to the receiver unit 10 NETWORK CABLE WIRING DIAGRAM Gefen has specif cally engineered their products to work with the TIA EIA 568 B specif cation Please adhere to the table below when f eld terminating cable for use with Gefen products Failure to do so may produce unexpected results and reduced performance Blue White Brown White 12345678 This product was designed for use with CAT 6a augmented cabling only This unit will either not perform to specif cation or refuse to operate completely if cabling other than CAT 6a is used Each cable run must be one continuous run from one end to the other No splices or use of punch down blocks 11 SPECIFICATIONS Video Amplif er Bandwidth 225 MHz Single Link Max Resolution 1080p 60 12 bit color input DDC Sigal een ee ae 5 Volts p p TTL INPUL Video 1 2 Volts p p ADMI CENNECIOF serrin canica Type A 19 Pin Female Link 8 ___ RJ 45 Shielded Power SUPDIY 2er 5V DC 0 6A each Power Consumption en 3 Watts per unit Dimensions 3 3 W x 1 3 H x2. is enabled distance performance will be limited to 150 feet 50 meters with premium CAT 6a cabling FEATURES Features e Flexible extension of high bandwidth HDMI 1 3 thanks to inexpensive and widely available CAT6 cable e Audio and video are transmitted digitally over the CAT6 cable for zero signal loss e Single Link Range maximum resolution 1080 60 12 bit color depth Compliant with HDMI 1 3 HDMI 1 2 HDCP 1 1 and DVI 1 1 standards e Supports digital video formats in Deep Color Mode at up to 12bits color e Supports lossless compressed digital audio Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio e Equalizes incoming HDMI signal and retransmits it with optimal quality regardless of incoming signal quality e Eliminates equipment noise in the viewing environment e Improved compensation for cable skew HDMI 1 3 Features Supported e Dolby TrueHD amp DTS Master Audio e Deep Color Supported XV Color e 225 MHz up to 12 bit YUV 444 1080p Protocol Pass Through e Lip Sync Pass Through Package Includes 1 Extender for HDMI 1 3 over one CAT6 Sender 1 Extender for HDMI 1 3 over one CAT6 Receiver 1 6 Foot HDMI to HDMI Cable M M 2 5V DC Power Supply 1 User s Manual SENDER PANEL LAYOUT Front Panel Back Panel SENDER PANEL DESCRIPTIONS 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket Powe
3. s reliable plug and play products supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen Extender for HDMI 1 3 over one CAT6 The Gefen Extender for HDMI 1 3 over one CAT6 will send a 1080p 60Hz HDMI 1 3 signal with 12 bit Deep Color support over a single CAT 6a cable at distances of up to 175 feet 50m HDMI 1 2 is still fully supported and can be extended up to 200 feet 60m at resolutions of 1080i p 60Hz Extension of high def nition can now be simplif ed with the use of only a single CAT 6a cable Previous solutions used two cables to accomplish this The Gefen Extender for HDMI 1 3 over one CAT6 supports the HDMI 1 3 specif cation with features such as Deep Color Full 1080p HD and compressed lossless audio formats such as Dolby TrueHD and DTS HD Master Audio The CAT6 extender s pure digital transmission method insures 100 signal integrity over this single cable extension solution How It Works The Gefen Extender for HDMI 1 3 over one CAT6 system consists of send and receive units The HDMI source set top box DVD player or gaming console connects to the sender unit with the supplied 6 foot HDMI cable The receiver unit connects to an HDTV display One CAT 6a cable links the sender and receiver together at distances of up to 200 feet Power is applied to both the sender and receiver
4. trimpot in a clockwise fashion until it clicks into the next position Continue adjusting the trimpot by trying all 8 positions until the issue is resolved 3 Carefully remove the adjustment tool DIP SWITCH CONFIGURATION DIP SWITCH CONFIGURATION DEEP COLOR By default Deep Color support is disabled DIP 2 in the OFF position If Deep Color support is needed you can change the position of one of the DIP switches on the bottom of the receiver 1 If the Receiver unit is currently being powered please disconnect the power adapter from the unit Turn the receiver unit upside down and locate the 4 DIP switch bank on the bottom of the unit NOTE You may need to remove the piece of silver colored metallic tape to expose the DIP switch bank Refer to the image below and locate DIP 2 on the DIP switch bank ON 1234 Move DIP 2 to the position This will enable Deep Color support and will be used only if the display supports this deep color NOTE DIP 1 must be in the OFF position in order to enable deep color Reconnect power to the receiver unit DIP SWITCH CONFIGURATION DIP SWITCH CONFIGURATION EDID Under normal circumstances a source device digital and analog will require information about a connected device display to assess what resolutions and features are available The source can then cater its output to send only resolutions and features that are compatible with the attach
5. 3 3 D Shipping Weight lio llista 3 lbs 12 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notif ed within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modif cations Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or ftness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulti
6. T 6a cable CONNECTING AND OPERATING THE EXTENDER How to Connect the Extender for HDMI 1 3 over one CAT6 1 Connect a HDMI cable one is supplied between the HDMI output on a HDMI source device and the HDMI input on the Extender for HDMI 1 3 over one CAT6 sending unit 2 Connect a single CAT 6a cable between the sending and receiving units NOTE When f eld terminating CAT 6a cabling please adhere to the TIA EIA 568 B specif cation Please see page 11 for more information 3 Connect a HDMI cable user supplied between the HDMI input on a HDMI capable output device i e HDMI display and the HDMI output on the Extender for HDMI 1 3 over one CAT6 receiving unit 4 Connect the included 5V DC power supplies two are included between the sending and receiving units and open wall power sockets 5 Initialize the HDMI output device i e HDMI display f rst and the HDMI source device last How to Equalize the Extender for HDMI 1 3 over one CAT6 The Extender for HDMI 1 3 over one CAT6 receiving unit has a equalization Trim to compensate for the extension distance and the quality skew variances that are found in different CAT 6a cabling brands If there is no output video or if output video has video artifacting and or video noise please use the steps below to adjust the equalization trimpot 1 Insert a small f at head tool into the trimpot on the front panel of the receiver unit 2 The trimpot has 8 set positions Turn the
7. am Geren Extender for Homi 1 3 over one CAT G EXT HDMI1 3 1CATG User Manual www gefen com Hom 8 gt HIGH DEFINITION MULTIMEDIA INTERFACE DT Blu ray Disc ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday PST Write To Gefen Inc c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Extender for HDMI 1 3 over one CAT6 is a trademark of Gefen Inc 2009 Gefen Inc All Rights Reserved All trademarks are the property of their respective companies Rev B CONTENTS 1 Introduction Operation Notes Features N Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions Connecting And Operating The Extender A DIP Switch Configuration 11 Network Cable Wiring Diagram 12 Specifications 13 Warranty INTRODUCTION Congratulations on your purchase of the Extender for HDMI 1 3 over one Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen
8. ed device display This information is called EDID Extended Display Information Data and a source device can only accept and read one EDID from a connected device display Likewise the source can only output one resolution for use by a connected device display The Extender for HDMI1 3 over one CAT6 uses DIP 1 to control EDID modes There are 2 EDID modes LOCAL and PASSTHROUGH The LOCAL mode will create a new EDID by copying all video and audio features of the connected device but will allow the user to control Deep Color support by the procedure on the previous page By default the unit is shipped in LOCAL mode where DIP 1 is in the OFF position The PASSTHROUGH mode will simply allow all video and audio features of the connected device to pass through to the source device without control over Deep Color support DIP 1 can be switched to the ON position to enable the PASSTHROUGH mode However if DIP 1 is switched to the ON position enabling Deep Color DIP 2 ON will not affect the video features of the EDID When switching DIP 1 between the OFF and ON position please follow the procedure outlined below 1 Disconnect power from the receiver and locate the DIP switch bank on the bottom of the unit NOTE You may need to remove the piece of silver colored metallic tape to expose the DIP switch bank 2 Refer to the DIP switch image below and locate DIP 1 on the DIP switch bank ON OFF 1234 3 Move DIP 1 to the ON
9. ng from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specif cations is subject to change without notice 13
10. r LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and an open wall power socket HDMI Input With Mono LOK Secure Connector This input will accept a single HDMI source for extension This input features a Mono LOK connector Gefen part CAB HDMI LCK XXMM for a secure cable connection This input will accept a standard or style HDMI cable Link RJ45 Port This port is used to connect the sending and receiving units together using a CAT 6a cable RECEIVER PANEL LAYOUT Front Panel Back Panel RECEIVER PANEL DESCRIPTIONS Equalization Adjustment This trimpot is used to equalize the signal to compensate for the extension distance and the quality skew variances that are found in different CAT 6a cabling brands HDMI Input With Mono LOK Secure Connector This input will accept a single HDMI source for extension This input features a connector Gefen part CAB HDMI LCK XXMM for a secure cable connection This input will accept a standard or Mono LOK style HDMI cable Power LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and an open wall power socket 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket Link RJ45 Port This port is used to connect the sending and receiving units together using a CA
11. with the included 5V DC power supplies A perfect image is now displayed on the remote HDTV display Note This product is an HDCP pass through device OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE EXTENDER FOR HDMI 1 3 OVER ONE CAT6 e Extender for HDMI 1 3 over one CAT6 was designed for use with high quality augmented cabling This unit will either not perform to specif cation or refuse to operate completely if cabling other than CAT 6a is used When feld terminating CAT 6a cabling please adhere to the TIA EIA 568 B specif cation Please see page 9 for more information e Extender for HDMI 1 3 over one CAT6 has a maximum distance rating based on the bandwidth i e resolution and color of the video being transmitted The following specif cations are based on high quality CAT 6a cabling e 200 feet 60 meters at 1080p 60Hz with up to 10 bit color depth and with all HDMI 1 2 1 3 audio formats e 150 feet 50 meters at 1080p 60Hz with up to 10 bit color depth and with all HDMI 1 3 audio formats e 66 feet 20 meters at 1080p 60Hz with up to 12 bit color depth and all HDMI 1 3 audio formats The Extender for HDMI 1 3 over one CAT6 is HDMI 1 3 and HDMI 1 2 compliant e This product features HDCP pass through e By default Deep Color support is disabled To enable Deep Color support please see the DIP switch conf guration guide on page 9 Please note that once Deep Color
Download Pdf Manuals
Related Search