GE V2FN Installation Guide
Contents
1. GEH 3942C INSTRUCTIONS Versaflood II Signliter Pipe Support Bracket r by user 1 Set Screws io Slipfitter e Anti rotation 1 2 p bolt amp nut bolts i S i Figure 1 Degree Marker Bolts Wiring Shield w 2 screws Terminal Board Strain Relief Gland amp Clamp w screw Figure 3 Figure 4 Loosen the cable strain relief clamp and insert the supply cable through the gland from the back 7 to 9 inches Connect cable leads to the terminal board retract cable to a good wire dress and tighten the strain relief clamp Refer to the WIRING section of this instruction Replace the wiring shield and reflector and install lamp Close and latch the lens door 3a Pipe Mounted See Figure 1 Mount the trunnion slipfitter on the support pipe bracket and tighten all six set screws Mount the luminaire and trunnion to the slipfitter using the 1 2 inch bolts and nuts provided Level the These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions luminaire Drill a 5 16 inch dia2. GE Lighting Solutions READ THOROUGHLY BEFOREINSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions GENERAL This luminaire is designed for use in outdoor applications and should not be installed in areas of limited ventilation or in high ambient temperature enclosures This fixture should be installed and main tained according to the following recommendations UNPACKING This luminaire has been packed so that no parts should have been damaged during transit Inspect to confirm INSTALLATION A CAUTION Unit will fall if not installed properly e Follow installation instructions CAUTION For aimed up application remove two screws from rear bottom corners of back housing and re install them in front housing rear bottom corners Luminaires Installed Without Conduit Standard mounting Type SO AWG 14 3 cable normally supplied by user is recommended for electrical connections to this luminaire 1 Unlatch open door and remove door assembly Remove reflector and shield 2 Remove 4 knockouts in housing back Using these holes install housing to mounting surface with 4 5 16 inch bolts nuts and lock washers Seal around these bolts with appropriate sealing compound Supplied by user 3 Ifthe luminaire is prewired with power supply cable proceed to instruction 3a or 3b otherwise remove the wiring shield to expose the terminal board see Figure 4
3. ith the insulated connector IF SINGLE VOLTAGE All single voltage ballasts are pre wired such that user need only connect the supply conductors IF MULTIVOLT 120 208 240 277 volts Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal nameplate IF MULTIWATT Multiwatt ballasts are available in various combina tions of wattage See wiring instructions on wiring tag inside the luminaire FINAL ASSEMBLY Photoelectric Control The photoelectric control receptacle if present Should be oriented before the control is installed Loosen the two screws and rotate the receptacle to the desired direction Retighten the screws and install control MAINTENANCE A CAUTION Risk of burn Allow lamp fixture to cool before handling A WARNING Risk of burn e Do not touch operating luminaire It will occasionally be necessary to clean the outside of the refractor to maintain the light level Frequency of cleaning will depend on the ambient dirt level and the minimum light level which is acceptable to the user The lens door should be washed in a solution of warm water and any mild non abrasive household detergent rinsed with clean water and wiped dry Should the optical assembly become dirty on the inside wipe the reflector and clean the lens door in the above manner and replace any damaged gaskets LAMP INSTALLATION REPLACEMENT Use only lam
4. meter hole through the pipe bracket using the through hole in the slipfitter as a guide Install the anti rotation bolt and nut with the head of the bolt on the top side of the slipfitter The power supply cable may now be fed through the slipfitter and pipe bracket 3b Bracket Mounted Luminaires See Figure 2 Mount the luminaire on the support structure with 5 16 inch minimum bolts nuts and lockwashers that are supplied by the user Position aim and tighten bolts at the degree markers 3 4 INCH CONDUIT MOUNTED LUMINAIRES See Figure 3 1 Mount the luminaire on the support structure with 5 16 inch minimum bolts nuts and lockwashers that are supplied by the user 2 Unlatch and open the lens door Remove the reflector that is held by three screws Remove the wiring shield that is held by two screws 3 Install conduit and supply wiring Dress the wires to the terminal board so they will not touch the reflector when reinstalled Refer to the WIRING section of this instruction Replace the wiringshield Replace the reflector Install the lamp Close and latch the lens door WIRING Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements Verify that supply voltage is correct by comparing it to nameplate Do not remove insulated connectors from wires not needed for required voltage connection When changing voltage on reconnectable units move only the lead w
5. ps specified on nameplate Observe lamp manufacturer s recommendations and restric tions on lamp operation particularly ballast type burning position etc The light output of a luminaire is also dependent on the age of the lamp In applications where the light level is critical it may be desirable to replace lamps before they reach end of life The lamp manufacturer can provide data showing how the lamp light output decreases with use Lamp Tightness Mogul Base Lamp The lamp should be securely inserted to the NEMA EEI specified torque of 35 inch pounds which is best achieved by very firmly tightening to insure application of sufficient torque Tightening must be sufficient to fully depress and load the center contact of the socket Lamp Tightness Medium Base Lamp The lamp should be tightened to a light firmness sufficient to depress the center contact GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 N4 6 00
Download Pdf Manuals
Related Search