GE GS Series Installation Guide
Contents
1. GE Installation Guide Lighting Lumination LED Luminaires GS14 Series BEFORE YOU BEGIN Read these instructions completely and carefully WARNING AVERTISSEMENT RISK OF ELECTRIC SHOCK RISQUES DE DECHARGES ELECTRIQUES e Turn power off before inspection installation or removal e Coupez l alimentation avant d inspecter installer ou d placer le luminaire e Properly ground electrical enclosure e Assurez vous de correctement mettre la terre le bo tier d alimentation lectrique RISK OF FIRE RISQUES D INCENDIE e Follow all NEC and local codes e Respectez tous les codes NEC et codes locaux e Use only UL or IEC approved wire for input output connections e N utilisez que des fils approuv s par UL ou IEC pour les entr es sorties de Minimum size 18 AWG 0 75mm connexion Taille minimum 18 AWG 0 75mm e Do not install insulation within 3 inches 76 mm of luminaire top e Maintenir une distance de 76 mm 3 pouces entre le luminaire et l isolant Save These Instructions Use only in the manner intended by the manufacturer If you have any questions contact the manufacturer Prepare Electrical Wiring Electrical Requirements e The LED luminaire must be connected to the mains supply according to its ratings on the product label Grounding Instructions e The grounding and bonding of the overall system shall be done in accordance to local electric code of the country where the luminaire is installed imag2. cket T8 Socket LED Driver Out SKU 94385 LED21T8 Out Class 2 Out F 9 Ground screw on geartray This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class A RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe A est conforme la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense GE Lighting 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lighting Solutions LLC is a subsidiary of the General Electric Company The GE brand logo and Lumination are trademarks of the General Electric Company 2014 GE Lighting Solutions LLC In
3. formation provided is subject to change without notice All values are design or typical values when measured under laboratory conditions IND121 070914
4. ination at work Components Included Housing base 1 Lens 1 3 Geartray including T8 sockets 1 O Ground screw 1 Geartray clips 2 Lanyard 2 Housing latches 2 LED diver 1 LED T8 tubes 2 Mounting brackets 2 Endplugs 2 O00000 Installation Chain and S hook 1 Mount the wrap around brackets on the ceiling or support rail using appropriate hardware After brackets are secured in place install one side of the housing in the bracket then rotate up and snap the other side of the housing into bracket Chain and S hook not included can also be used to support the brackets Unfasten the 6 latches and remove the lens 3 Remove the LED T8 tubes optional QO Remove one or two of the end plugls as needed Q Install a water tight fitting be sure to install the to wire the unit to the AC line fitting washer and feed the AC line wire through the fitting Push down until clips click into place 8 Connect the AC line to the black line and white Reattach the geartray making sure the two tray neutral input wires of the LED driver using clips are properly engaged 14 18AWG twist on wire connectors Connect the ground wire to the green grounding screw 10 Reinstall the two LED T8 tubes a1 Reinstall the lens and secure the 6 latches Wiring Diagram GE LED T8 Tube T8 Socket T8 Socket GE LED T8 Tube T8 So
Download Pdf Manuals
Related Search