Home

GarrettCom 6K16V User's Manual

Contents

1. cccccccecseesseeseceseceeeceeeeeeeseeeeeeseeeeeens 30 3 7 Connecting a Management Console Terminal to Magnum 6K 16V 31 3 7 1 RS 232 DB 9 Console Com port Serial port pin 31 4 0 OPERATION ou cccssssssccssscccncscescscenesessncsseseecessssssesssssssnsssseneseesness 32 4 1 Switching Functionality 00 ec eceeecseeeeceeeeeceeeseeeseceeeeecevereeaeeneeaeens 32 Al Stats LEDS orrn o A cess vx E T 33 4 3 Up link Manual Switches set as for RJ 45 port only 33 4 4 Auto negotiation for Fast Ethernet copper ports 33 4 5 Flow control IEEE 802 3x standard 0 cccccccccceessscecessceceesseeeceeees 35 4 6 Power Budget Calculations for Magnum 6K16V PM s eee 35 iii Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 5 0 Introduction Magnum 6K16V Managed Fiber Switch PM 37 5 1 Inspecting the Package and Product 0 eeeceseeeeeceeeeeeeeeeeeeeeeeeres 37 5 2 6KPM Module Description cccecceecceesceseceseceeeceeeeaeeeseeeneeseeeeeeees 37 5 2 1 6KP6 RJMST Combo Module cccccccceecccceesssceceeseceensseeeees 38 5 2 la 6KP6 RJLOST Combo Module cc cccccccscceseeessecesseeeseeenees 38 5 2 1b 6KP4 F10ST 4 10Mb multi mode FX ST twist lock 38 5 2 lc O6KP4 FLSTFX 2 Module cccecccccceseeeceseeseeteeeeeeeseeseeneees 39 5 2 2 OK P6 RIMSC O 40 5 2 3 6KP6 RJSSC snap in CONNECCHOL cece
2. 4 1 Switching Functionality A Magnum 6K 16V provides switched connectivity at Ethernet wire speed among all of its ports The Magnum 6K16V supports10 100Mbs for copper media and 10 or 100Mb separate traffic domains for fiber ports to maximize bandwidth utilization and network performance All ports can communicate to all other ports in a Magnum 6K16V but local traffic on a port will not consume any of the bandwidth on any other port Magnum 6K16V units are plug and play devices There is no software configuring necessary to be done for basic operation at installation or for maintenance The only hardware configuration settings are user options for an UP LINK Switch resides inside the unit on the 6K8 RJ45 Optional Half Full duplex mode and 10 or 100Mbps selection for the switched ports must be configured through MNS software per unit as per the requirement The internal functions of both are described below Filtering and Forwarding Each time a packet arrives on one of the switched ports the decision is taken to either filter or to forward the packet Packets whose source and destination addresses are on the same port segment will be filtered constraining them to that one port and relieving the rest of the network from having to process them A packet whose destination address is on another port segment will be forwarded to the appropriate port and will not be sent to the other ports where it is not needed Traffic needed for maintaining
3. B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 36 70 VDC Power Supply Internal 24VDC Dual Source model Dual Src 24V DC Power Connector First Source A Ane 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 20 36 VDC Power Supply Internal 125VDC Dual Source model Dual Sre 125V DC Power Connector First Source A Ane 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 115 150 VDC With the exception of the dual DC input power connections and the power supply all specifications and configuration options for the Magnum 6K16V 48VDC 24VDC and 125VDC models with this Dual Source option are identical to those listed in the Magnum 6K16V Fiber Switches Installation and User Guide including Appendix B Internal DC Power Supply Option C2 0 MAGNUM 6K16V with 48VDC 24VDC and 125VDC Dual Source option The 6K16V Switch models with the internal 48VDC 24VDC and 125VDC Dual Source power supply are designed for installations where a battery plant is the power source and where two separate power sources are utilized in order to increase operational uptime and to simplify maintenance The functionality of the Magnum 6K16V Switch 48VDC 24VDC and 125VDC
4. CAUTION Do not pack the unit in Styrofoam popcorn type packing material This material may cause electro static shock damage to the unit 2 Clearly mark the Return Material Authorization RMA number on the outside of the shipping container 3 GarrettCom is not responsible for your return shipping charges 4 Ship the package to GarrettCom Inc 213 Hammond Ave Fremont CA 94539 Attn Customer Service APPENDIX A WARRANTY INFORMATION GarrettCom Inc warrants its products to be free from defects in materials and workmanship for a period of three 3 years from the date of shipment by GarrettCom During this warranty period GarrettCom will repair or at its option replace components in the products that prove to be defective at no charge other than shipping and handling provided that the product is returned pre paid to GarrettCom This warranty will not be effective if in the opinion of GarrettCom the product has been damaged by misuse misapplication or as a result of service or modification other than by GarrettCom GarrettCom reserves the right to make a charge for handling and inspecting any product returned for warranty repair which turns out not to be faulty Please complete the warranty card as this acts as a product registration and mail it to GarrettCom within two weeks of your purchase i es 50 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 APPENDIX B Internal DC Power Supply O
5. DB 9 connectors for RS 232 null modem connection sometimes called an X modem cable used to connect a PC or a character terminal to the Management port CONSOLE USB Industry standard serial cable DB 9 connectors for RS 232 null modem connection sometimes called an X modem cable to connect to a managed switch and a USB port to connect to a PC DIN RAIL VRM _ Set of two DIN Rail holders for a secure vertical mount of a 6K 16V unit with screws to attach to metal mounting brackets and to the 6K16V case Le GarrettCom Inc reserves the right to change specifications performance characteristics and or model offerings without notice Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 2 0 Introduction 2 1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product notify the carrier of any damage that you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 Magnum 6K16V Managed Fiber Switch base unit configured with user selected port module options installed 1 AC Power Cord U S and other 115 VAC only 1 Set of two metal vertical mounting brackets with screws to the case 1 Installation and User Guide this manual 1 Product Registration Card Remove the items from the shipping container B
6. 10 100 auto negotiation ports typically will not work properly The 6K16V Switch s RJ 45 ports handle this situation by configuring the ports as per desire through MNS software port settings and can check the port status of each port after the change i es 33 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 When Magnum 6K16V RJ 45 copper ports are set for auto negotiation and are connected to another auto negotiating device there are 4 different speed and F H modes possible depending on what the other device supports These are 1 100Mb full duplex 2 100Mb half duplex 3 10 Mb full duplex and 4 10 Mb half duplex The auto negotiation logic will attempt to operate in descending order and will normally arrive at the highest order mode that both devices can support at that time Since auto negotiation is potentially an externally controlled process the original highest order mode result can change at any time depending on network changes that may occur If the device at the other end is not an auto negotiating device the 6K16V s RJ 45 ports will try to detect its idle signal to determine 10 or 100 speed and will default to half duplex at that speed per the IEEE standard General information Auto negotiation per port for 802 3u compliant switches occurs when the devices at both ends of the cable are capable of operation at either 10 Mb or 100Mb speed and or in full or half duplex mode and
7. CAN BE CONNECTED IN STRINGS MIXED MEDIA FIBER HUB 16 PORT STACKABLE 10 100 AUTO SENSING DUAL SPEED 8 PORT AND 16 PORT STACKABLES 10 100 AUTO SENSING STACKABLE HUBS SNMP OPTIONAL 10MB SERIES AND 100MB SERIES BOTH W OPTIONAL PORT MODULES PERSONAL SWITCHES 10 100MB 8 PORT DUAL SPEED AUTO NEGOTIABLE WITH FIBER OPTION PERSONAL HUBS 100MB OR 10 100MB 8 PORT WITH TWO SWITCHED PORTS 1 FIBER BUILT IN PERSONAL HUBS 10MB SERIES 8 PORT AUI STACKABLE TO 5 HIGH OPTIONAL BNC OF FIBER PORT Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 8 OR 9 PORT AND 4 OR 5 PORT PERSONAL HUBS W MAN UP LINK SW MEDIA CONVERTERS 10MB AND 100MB SERIES ALL MEDIA COMBINATIONS INCL FIBER ST SC MM SINGLE MODE THE X LINE OF CONFIGURABLE MIXED MEDIA PRODUCTS STACKABLE CONCENTRATORS SNMP OPTIONAL 13 PORTS MINI CONCENTRATORS 7 PORTS REPEATERS 2 PORTS REPEATER PORT MODULES RPMS 6 TYPES FOR ETHERNET MEDIA BRIDGE PORT MODULES BPMS 4 TYPES FOR SEGMENT ISOLATION TRANSCEIVERS 10MB SERIES MINI TRANSCEIVERS AND COAX MODELS JUNE 04 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 1 0 SPECIFICATIONS 1 1 Technical Specifications Performance Filtering Forwarding Rate Ethernet 14 880 pps Fast Ethernet 148 800 pps Gigabit Ethernet 1 488 000 pps Switching Processing Type Store and Forward with IEEE 802 3x full duplex flow control non blocking Data Ra
8. Dual Source Option units is identical to the standard AC powered models Refer to the main sections of this Installation and User Guide for a detailed description of the Magnum 6K16V Switches C3 0 DUAL SOURCE OPTION THEORY OF OPERATION The Dual Source DC power option is designed using diodes inside of the chassis on each DC power input line A diode is placed in each of the four input lines behind the four external power connection terminals CHASSIS so that power from an external source can only flow into the unit This allows the unit to operate whenever DC power is correctly applied to either or both of the two inputs 54 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 C4 0 FEATURES AND BENEFITS OF THE DUAL SOURCE DESIGN a The Switch unit can receive power from either input A or B The hub will normally draw its power from the DC source with the highest voltage at a given time b The Switch unit will not allow power to flow from a higher voltage input to a lower voltage input i e the two DC power sources are not mixed together by the hub c When one correct DC input is present the Switch will receive power if the other DC input is absent or even if it is connected with reverse polarity or shorted or grounded d Reverse polarity connections if they should accidentally occur on either input will not damage the Switch or power supply internally nor will it blow the fuse in the inter
9. FDX HDX LED indicating full duplex mode when lit or half duplex when off 5 2 8 6KP8 45LC Combo 4 100Mbps multi mode LC small form factor and 4 10 100 Mbps RJ 45 Connector The Magnum 6KP8 45LC Module is a combo module with a combination of copper and Fiber Small Form 6KP8 45LC Factor LC type ports The small 4 Port 10 100Mbps amp 4 port 100Mbps Multi Mode LC 2 size of LC connectors give an advantage of having more ports on one module The 6KP8 45LC is equipped with 4 10 100 RJ 45 ports and 4 LC Small form factor multi mode fiber ports When installed in a Magnum O LINK 10 100 6K16V Switch it supports the GB ACTIVITY Q FULL HALF standard distances as per mentioned on 5 2 8 and the LEDs also acts similarly as mentioned above 5 2 9 6KP8 RJ45 Twisted Pair 10 100Mb 8 Port The 6KP8 RJ45 module supports Ethernet twisted pair segments of any standard length It is 6KP8 RJ45 8 Port 10 100Mb Copper ports equipped with an eight port RJ 45 connector and offers 10 100 full half duplex auto negotiating capability on each port The RJ 45 connector is shielded to minimize emissions and will allow both unshielded twisted pair UTP and shielded twisted pair STP cable connections The 6KP8 RJ45 module is equipped with a Media Dependent Interface Crossover MDI X switch which controls port 1 for cascaded connection This feature eliminates the need for a special twisted pair crossover
10. down simultaneously to release the 6K 16V so that it can be dismounted by pulling the bottom out Once the bottom of the 6K16V is rotated out the DIN Rail latch is not engaged and the 6K16V can be moved up and out free of the DIN Rail mounting The picture below is a front right side view of a DIN Rail mounted 6K 16V It shows vertical mounting of Magnum 6K16V on a DIN Rail track for proper convection cooling of the unit Note that there is air space in the rear as the 6K126V unit is held out from the rear of the panel by the mounting brackets The 6K16V design uses the case for cooling patent pending and needs to be mounted vertically with air flow space in the front rear and sides Fig 3 3 1 Magnum 6K16V mounted vertically with DIN Rail brackets and latches The DIN Rail mounting brackets and latches are optional and need to be ordered as separate items e g Model DIN RAIL VRM 3 3 1 Mounting Dimensions for 6K16V with metal brackets Each Mangum 6K16V is supplied with metal mounting brackets and screws to mount the unit securely It is recommended to mount the 6K16V vertically as shown below for proper cooling and long life reliability It is also advisable to mount the unit with space for air movement around the top and the sides typically a minimum of 1 inch _ www GarrettCom com sss 22 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Note that the back of the 6K16V unit is held out fr
11. earth or ground GND The connection procedure is straightforward Simply insert the DC leads to the Switch s power terminals positive and negative screws The use of Ground GND is optional it connects to the Switch chassis Ensure that each lead is securely tightened NOTE Always use a voltmeter to measure the voltage of the incoming power supply and figure out the ve potential lead or ve potential lead The more ve potential lead will connect to the post labeled ve and the rest to the ve The GND can be _ i U 52 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 hooked up at the last When power is applied the green PWR LED will illuminate Note The GND should be hooked up first The 6K16V unit has a floating ground so the user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the output voltage of the power supply and determine the lead which is more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled An ON OFF manual switch is optional for DC power This can be used to cut off power connections and as a RESET for the Magnum 6K16V Switch B4 1 UL Requirements for DC powered units Minimum 18AWG cable for connection to a Centralized DC power source Minimum 14AWG cab
12. fiber ports 17 watts typical for all RJ 45 Ports B2 0 48VDC 24VDC and 125VDC POWER THEORY OF OPERATION The 48VDC 24VDC and POWER SWITCH 125VDC power options are designed HUB using diodes inside on each DC power A input line behind the two external power A connection terminals so that the power CHASSIS S into the hub This allows the Switch to operate only whenever DC power is correctly from an external source can only flow i U 51 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 applied to the two inputs It protects the Switch from incorrect DC input connections An incorrect polarity connection for example will neither affect the Switch its internal power supply nor will it blow the fuse in the internal power supply The manual power On Off Switch optional is used for powering the unit on and off when it is placed into or taken out of service B3 0 APPLICATIONS FOR DC POWERED ETHERNET SWITCHES Magnum 6K 16 Series Switches are easily installed in a variety of applications where 48VDC 24 or 125VDC or 5VDC power is used as the primary power source The DC power configuration capability provides an Ethernet networking solution utilizing a special power supply in switches with a proven track record The 48 VDC solution is particularly useful in the telecommunication industry where it is common for facilities to operate on 48 VDC power Such companies include regular and
13. for a variety of Gigabit cabling types and distances High performance features GarrettCom Pe cere TY include non blocking speed on all ports and 802 1p QoS Traffic Prioritization Magnum 6K16Vs are plug and play ready for use as backbone switches where a mix of bursty data traffic and priority streaming traffic for VoIP and audio video applications is present Magnum 6K16V Fiber Switches are provided with LAN management software including SNMP Tag and Port based VLANs IGMP Snooping and Port Security control via command line interface For high availability LANs using ring topologies Spanning Tree Protocol Link Loss Learn and S Ring are available See the Managed Networks Software MNS 6K and S Ring datasheets for additional details on the comprehensive set of software programs and options Designed for use in transportation and traffic control systems power utilities industrial factory floor jobs and video surveillance systems with segments requiring Gigabit backbone interconnections the Magnum 6K16V is easy to install and operate The next generation of industrial applications will need advanced managed network software operation at extended temperatures fiber ports modularity support for self healing ring structures and gigabit backbone configurability The Magnum 6K16V has i es 7 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 all of these and is available now Magnum
14. in applications with LAN connections to an organization s multiple site offices and factory floors The different locations can be easily connected together with the Fiber ports supported by the Magnum 6K16V Switch A main NT server in a secure area protected from earthquake or fire hazards can be connected to the full duplex Gigabit Fiber port Extended temp ratings and wide options of AC DC power supply qualifies this managed 6K16V switch to use in temp controlled network floor and many others temp sensitive critical Industrial applications where above normal room temp is required to operate the network Full duplex future proof fiber media can easily connect long distance subnets and provide a stable secure network to all applications The SNMP management capability of the Magnum 6K16V Switch helps create a database of all the network subnets to easily manage the network Magnum 6K25 A SNMP z Monitor ie ee 4 Main SERVER IBER Connection fo Internet FIBER C ti 6 a onngction Storay y 4 EST Router Magnum FIBER Conngetion 6K16V IBA Connection FIBER Connection to other BLDG eA Factory Floor PLC pall Magnum iy 6Kigv n l Factory Factory Floor PLC Floor PLC Factory Floor PLC Fig 2 1 The Industrial factory floor application with Magnum 6K16V Example 2 In another application a managed network is needed to provide a Redundant ring topology for a for maximum
15. is 125VDC Configuration Options Each Magnum 6K16V base unit has TWO port module slots Magnum 6K16V Port Modules 6KP8V MTRJ SFF Fiber module w eight 100Mb mm FX MT RJ connectors 6KP8V MLC SFF Fiber module w eight 100Mbps mm FX LC connectors 6KP8V SLC SFF Fiber module w eight 100Mbps sgl m FX LC connectors 6KP4V FXSC 2 2 100Mb Fiber module w four 100Mb 2km FX SC connectors 6KP4V FXST 2 2 100Mb Fiber module w four 100Mb 2km FX ST connectors 6KP4V FIOST 2 2 10Mb Fiber module w four 10Mb 2km FL ST connectors 6KP4V FLSTFX 2 2 ST Fiber module w two 100Mb amp two 10Mb ports 2km 6KP8V RJ45 TP Module w eight 10 100Mbps auto negotiating RJ 45 ports 6KP8V 45MT 4 4 module w four RJ 45 ports and four 2km mm FX MT RJ s 6KP8V 45MLC 4 4 module w four RJ 45 ports and four 2km mm LC connectors 6KP8V 45SLC 4 4 module w four RJ 45 ports and four 2km sgl m LC connectors 6KP6V RJMST 4 2 module w four RJ 45 ports and two 2km mm FX SC s 6KP6V RJMSC 4 2 module w four RJ 45 ports and two 2km mm FX ST s 6KP6V RJSSC 4 2 module w four RJ 45 ports and two 20km Sgl m FX SC s 6KP6V RJSSCL 4 2 module w four RJ 45 ports and two 40km Sgl m FX SC s 6KP6V MT10ST 4 2 module w four MTRJ ports and two 10Mb 2km FL ST s 6KP6V RJ10ST 4 2 module w four RJ 45 ports and two 10Mb 2km FL ST s 6KM BLNK Blank cover for one 6K16V A B module slot opening in a 6K16V Gigab
16. media converter or almost any other device with a 10Mb fiber Ethernet port The default setting of the 100Mb module is full duplex User mode control per port through the MNS port settings software is the same as the other 6K16V modules The fiber ports support fiber cabling distances according to the 1OBASE FL and 100BASE FX standards i e 2km distance for multi mode fiber Single mode for up to greater distance may be available as a special order request quote 2 2 6 Gigabit 1000Mbps port modules The Magnum 6K16V offered a wide option Gigabit speed with multiple choice for the modular slot While up to two Gigabit modules maxm can be configured in the modular slot The Gigabit port option for the modular slot comes in couple of different configuration The two Giga port has been offered as GBPM 20TX fiber or RJ 45 whereas the single Gigabit module comes in flavor of G 4 10 100 RJ 45 ports or G 2 100Mb fiber ports as shown below in the figure 1 1000Mb Fiber SC 2 100Mb SC 1 1000Mb Fiber SC 4 10 100Mb The 6K16V Modules provide a GBIC opening for insertion of industry standard GBICs to provide Gigabit Gb media flexibility GBIC models are available for both multi mode 550m and single mode 10 25 40 70 km fiber options and for Gigabit copper as well with new models appearing often 11 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 The 1000Mb Gigabit fiber port modules on the
17. problems Please follow the suggestions listed below prior to contacting your supplier However if you are unsure of the procedures described in this section or if the Magnum 6K16V Switch is not performing as expected do not attempt to repair the unit instead contact your supplier for assistance or contact GarrettCom Customer Support 6 1 Before Calling for Assistance l If difficulty is encountered when installing or operating the unit refer back to the Installation Section of the applicable chapter of this manual Also check to make sure that the various components of the network are interoperable 2 Check the cables and connectors to ensure that they have been properly connected and the cables wires have not been crimped or in some way impaired during installation About 90 of network downtime can be attributed to wiring and connector problems 3 Make sure that an AC power cord is properly attached to each Magnum 6K16V Switch unit Be certain that each AC power cord is plugged into a functioning electrical outlet Use the PWR LEDs to verify each unit is receiving power 4 If the problem is isolated to a network device other than the Magnum 6K16V Switch product it is recommended that the problem device be replaced with a known good device Verify whether or not the problem is corrected If not go to Step 5 below If the problem is corrected the Magnum 6K16V Switch and its associated cables are functioning properly 5 If the
18. receive 6 receive other pins not used 5 2 10 6KP8 45 2MT 6 10 100Mbps RJ 45 and 2 100Mb multi mode FX MTRJ Small Form Factor The Magnum 6KP8 6KP86KP3MT 45 2MT eight port Module is a 6 Port 10 10Mbps amp 2 port 100Mb Multi Mode F CoS combo module with copper and fiber Small Form Factor MTRJ type ports The small sizes of MTRJ connectors give an advantage of placing more fiber ports on one module The G O LINK 10 100 6KP8 45 2MT is equipped with six 10 100 RJ 45 ports and two ACTIVITY Or ULL HALF 100Mb MTRJ fiber ports When installed in a Magnum 6K16V Switch it supports the standard distances as mentioned on 5 2 3 and the LEDs also act similarly www GarrettCom com 45 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 5 2 10a 6KP8 45 2LC 6 10 100Mbps RJ 45 and 2 100Mb single mode FX LC Small Form Factor The Magnum 6KP8 45SLC eight port Module is a combo module with copper and fiber Small Form Factor LC type fiber ports 6KP8 45 2SLC The small size of LC connectors 6 Port 10 100Kbps amp 2 port 100Mbps give an advantage of placing more ports on one module The 6KP8 45 2SLC is equipped with 6 10 100 RJ 45 ports and 2 Single SingleMode you LC mode fiber ports When installed in a Magnum 6K16V Switch it supports the G LINK 10 100 standard distances as mentioned on 5 2 4 and the LEDs also act EANES ee similarly 5 2 11
19. receiving Activity on that port when lit The 10 100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF when auto negotiation is not disabled The FDX HDX LED is ON to indicate full duplex operation and OFF to indicate half duplex mode A twisted pair cable must be connected into an RJ 45 port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port Using the 6K16V s MNS software the user may disable auto negotiation and fix the desired operation of each RJ 45 port MNS Software set up may select 10Mb or 100Mb speed and full or half duplex mode per port as per user requirement See Magnum 6K16V MNS Software Manual for details info 2 2 3 Six Port 4 2 Combo Modules 4 10 100 RJ 45 and 2 100Mb fiber The combo six port modules are combinations of copper and fiber media i es 9 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 available as four 10 100 switched RJ 45 copper ports and two 100Mb switched multi mode fiber ST SC or single mode SC or Long Reach SC ports For ports numbering ports 1 3 5 7 are copper ports 2 and 6 are fiber ports 4 and 8 are not present 7 Y i gt tid CT A e Loe Ee Tellfel X cK RX 2 TX gLKRX p 4 RJ 45 2 100Mb SC The four RJ 45 ports operate just like the 8 port copper
20. redundant network where any faulty cable or disconnecting of cable can be reconfigured the network up running in mili seconds The ring topology of the network consists of high speed LAN segments supported by 16 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 100Mbps full duplex future proof fiber media to provide secure long distance LAN connection The entire network is sharing a higher bandwidth Gigabit enabled data mining server for the vital database located in a separate secured building The copper ports are required for multiple subnets inside the power plant to check the The entire spread network will be manageable to provide easy detectable uninterrupted support through a viewable SNMP monitor The Magnum 6K16V Managed Fiber Switch equipped with the mix of copper and fiber ports provides an economical and seamless solution to the requirements The user configurable Magnum 6K 16V provides an extra boost to the network requirements by providing copper fiber media along with the higher bandwidth support of 10 100 and 1000Mb The user can utilize the SNMP feature equipped with VLAN RMON STP and other standard managed LAN features to provide a secure and stable network The 6K16V Managed Fiber with S ring and Link Loss Learn feature easily fulfilled the redundant requirement in a secured and faster reconfiguration time for cable breakup by setting up in a ring topology The Gigabit port option boosts the band
21. strength sheet metal Suitable for vertical wall or DIN Rail mounting Dimensions 9 5 in Hx 8 75 in Wx 1 75 in D 24 1 cm Hx 22 2 cm W x 4 4 cm D Cooling method Convection designed for vertical mounting no fans Weight 4 21 Ibs 1 9 kg Management Console connector DB 9 for RS 232 null modem cable sometimes called an X modem cable Power Supply Internal AC Power Connector IEC type male recessed at rear of chassis Input Voltage 100 to 240 VAC auto ranging Input Frequency 47 to 63 Hz auto ranging Power Consumption 50 watts typical for a fully loaded fiber model 30 watts typical for a fully loaded copper only model DC Power Supply Options 48VDC Power Input Voltage 36 to 70 VDC 24VDC Power Input Voltage 20 to 36 VDC 125VDC Power Input Voltage 115 to 1SOVDC 5VDC Power Input Voltage or 5 Std Terminal Block GND Power Consumption same as for AC models see above i es 2 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 For DC internal power supplies at 48 VDC 24VDC and 125VDC including Dual Source options for continuity of operation when either of the DC input sources are interrupted see Appendices B and C Per port jumpers and switches The copper daughter board has on internal switch for selecting MDI MDIX crossover on port 1 Factory default setting is MDI user port Other port specific user settings such as FDX or HDX copper 10 100 spe
22. 0 9 125 4 0 21 15 17 5 70 ZXSC40 aa GBIC 1000Mb Single 1550 9 125 3 0 23 18 20 5 102 ZXSC70 mode Note The use of either multi mode or single mode fiber to operate at 100Mbps speed over long distances i e in excess of approx 400 meters can be achieved only if the following factors are both applied e The 100Mb fiber segment must operate in full duplex FDX mode i e the full duplex factory default setting for 1OOMbps fiber ports must be used and e The worst case OPB of the fiber link must be greater than the fiber cable s passive Attenuation Attenuation Cable loss LED aging loss Insertion loss safety factor 36 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 5 0 Introduction Magnum 6K16V Managed Fiber Switch Port Modules This chapter describes each Port Module PM including appearance functionality and status displays 5 1 Inspecting the Package and Product This section applies only to PMs shipped as separate items i e 6K16V PMs not factory installed in a Magnum 6K16V PM slot Examine the shipping container for obvious damage prior to installing a 6K16V PM notify the carrier of any damage you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 or more 6K16V PMs Installation instructions with illustrati
23. 0 100 the same LEDs indicating port ACTIVITY rorem ALF activity ACT Link LK and FDX HDX and 10 100 operation and the same face plate lettering While the functionality of these two modules is essentially the same the 6KP6 RJMSC is equipped with an SC type snap in connector instead of an ST type 5 2 3 6KP6 RJSSC 4 10 100Mbps RJ 45 Ports and 2 100Mbps single mode FX SC type snap in connector The Magnum 6KP6 RJSSC 6KP6 RJMSSC is also a Combo module 4 Port 10 100Mbps and 2 100 Mb SSC Fiber Port equipped with 4 dual speed copper ports and 2 Single mode SC type connectors It provides an advantage through combining copper and Fiber functions in one module of the 6K16V Switch Q ACHIVITY Q FULL HALF supporting four Copper and two single mode fiber network segments The 6KP6 RJSSC when installed ina Magnum 6K16V Switch operates on copper at the 100m distance The Fiber is single mode and cable lengths can be as much _ i 40 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 as 25 Km see Power Budget Section 4 5 Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and a FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates 100Mbps speed when lit and 10Mbps speed when off To distinguish the single mode 6 K6 RJSSC from the multi mode
24. 6K16V Managed Fiber Switches have heavy duty metal cases and auto ranging power supplies for operation with standard AC power worldwide Internal DC power supplies are optional All DC power input types 5V 24V 48V 125V are supported and dual source input is optional on all except SVDC There are two Alarm Relay contacts provided on each Magnum 6K16V Switch to monitor basic operations One is for hardware and will signal loss of power internally The other is software controllable and will signal user defined software events such as a security violation or an S Ring fault condition The wide variety of port modules are key to the flexibility and adaptability 2 2 1 Eight port SFF fiber modules 6K8 MTRJ 6K8 MLC 100Mb fiber ACT 1 a 5 7 fe L C C Ae Fig 2 2 2 cu gal noe ee ee SFF Fiber Port Modules EMGUQE Se GE ig and mug a ko 8 6K8 MLC or SLC below In an eight port SFF 1 5 7 fiber port module all of the fiber Ker a fa a a ACT if Ge i ports are of the same speed 100Mb mode and connector type Models are available with Small Form Factor SFF are multi mode MT RJ or LC type connectors and single mode LC type connectors The 100Mb fiber eight port modules for the Magnum 6K16V s normally are set factory default to operate in full duplex mode for best fiber distance and performance Using the 6K16V s MNS software the user may select full or half duplex mode per port
25. 6K6 RJMSC the label Sgl M is at the top of the faceplate of the 6K6 RJSSC 5 2 4 6KP6 RJSSCL 4 10 100 Mb copper port and 2 100Mbps single mode FX SC type snap in connector The Magnum 6KP6 RJSSC is also a Combo module equipped with 4 dual speed copper ports and 2 Single mode Long Reach SC type connectors It provides a combination of copper and Fiber functions in one module to the 6K16V Switches supporting four Copper and two single mode Long Reach fiber network segments The 6KP6 RJSSC when installed ina Magnum 6K16V Switch has copper supporting the 100m distance and Fiber supporting single mode fiber cable lengths of as much as 40 Km see Power Budget Section 4 5 Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 100Mbps when the LED is ON and 10 Mb when the LED is OFF 5 2 4a 6KP6 RJ10ST 4 10 100 Mb copper port and 2 10Mbps multi mode FL ST type twist lock connector The Magnum 6KP6 RJ10ST is also a Combo module equipped with 4 dual speed copper ports and 2 multi mode 10 Mb fiber ST type connectors It provides a combination of copper and Fiber functions in one module to the 6K16V Switches supporting four Copper and two 10Mb of ST fiber network segments The
26. 6KP6 RJ10ST when installed in a Magnum 6K16V Switch has copper supporting the 100m distance and Fiber supporting multi mode fiber cable allow to connect the legacy network of 10Mb requirement in the network Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 1OMbps when the LED is ON and 10 Mb when the es 41 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 LED is OFF 5 2 5 6KP8 MTRJ 8 100Mb multi mode FX MTRJ Small Form factor Magnum 6KP8 MTRJ is a multi mode fiber optic 8 port module equipped with a small form factor MTRJ type 6KP8 MTRJ cmall form factor 8 Port 100Mbps Multi Mode Fiber port connector It looks almost like an RJ 45 port but it is black in color The MT RJ s small size and ease of connection make it I 3 5 T ru LKE LK L I fiber to the desktop Ethernet we g g N connectivity When installed in E LKE EAL TE fe a Magnum 6K16V Switch it ACTIVITY supports fiber optic cable O FULL HALF distances up the IEEE standard LINK 100Mbps distance limits i e a good choice for 100Mbps typically 2km at full duplex and 412m at half duplex The functionality of this 100BASE FX multi mode 8 Port module is essen
27. Duplex ports which provides for a PAUSE packet to be transmitted to the sender when the packet buffer is nearly filled and there is danger of lost packets The transmitting device is commanded to stop transmitting into the 6K16V Switch port for sufficient time to let the Switch reduce the buffer space used When the available free buffer queue increases the Switch will send a RESUME packet to tell the transmitter to start sending the packets Of course the transmitting device must also support the 802 3x flow control standard in order to communicate properly during normal operation Note When in Half Duplex mode the 6K16V Switch implements a back pressure algorithm on 10 100 Mb ports for flow control That is the switch prevents frames from entering the device by forcing a collision indication on the half duplex ports that are receiving This temporary collision delay allows the available buffer space to improve as the switch catches up with the traffic flow 4 6 Power Budget Calculations for Magnum 6K16V PM s with Fiber Media Receiver Sensitivity and Transmitter Power are the parameters necessary to compute the power budget To calculate the power budget of different fiber media installations using Magnum products the following equations should be used OPB Optical Power Budget P min Pr min where Pr Transmitter Output Power and Pg Receiver Sensitivity Worst case OPB OPB 1dB for LED aging 1dB for inse
28. GBIC SXSC Gigabit fiber 1000Mb multi mode SC Connector The Magnum GBIC SXSC is a multi mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the IEEE 802 3z standard 1000Mbps distance limits i e 550m at full duplex 1 1000Mb Fiber SC 4 10 100Mb The GBIC transceiver has been offered in the modular slot with multiple options as per the user requirement The two Giga port has been offered as GBPM 2O0TX fiber or RJ 45 whereas the single Gigabit module comes in flavor of G 2 100Mb fiber ports or G 4 10 100 RJ 45 ports as shown in the above figure The GBIC transceiver is fastened using snap in clips Insert the transceiver take care to insert it the right way up arrows on top until it clicks in space While www GarrettCom com 46 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 removing the transceiver press the clips on either side of the transceiver at the same time and pull the transceiver out Each port has an Activity ACT LED indicating packets being received and a Link LK LED indicating proper connectivity with the remote device when lit 5 2 1la GBIC LXSC Gigabit fiber 1000Mb multi mode SC Connector The Magnum GBIC LXSC is a single mode Gigabit fiber connector equipped with SC type connectors and can be e
29. LC 15 km 6KP8V SLC 100m 328 ft 6K8 RJ45 2 sgl m single mode Connecting Fiber Optic ST type twist lock The following procedure applies to installations using a PM with ST type fiber connectors This procedure applies to ports using a 6K16V module MST type port 1 Before connecting the fiber optic cable remove the protective dust caps from the tips of the connectors on the PM Save these dust caps for future use 2 Wipe clean the ends of the dual connectors with a soft cloth or lint free lens tissue dampened in alcohol Make certain the connectors are clean before connecting Note One strand of the duplex fiber optic cable is coded using color bands at regular intervals you must use the color coded strand on the associated ports at each end of the fiber optic segment 3 Connect the Transmit TX port light colored post on the Magnum PM to the Receive RX port of the remote device Begin with the color coded strand of the cable for this first TX to RX connection 4 Connect the Receive RX port dark colored post on the PM to the Transmit TX port of the remote device Use the non color coded fiber strand for this 5 The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends and when power is ON in the unit If LINK is not lit after cable connection the normal cause is improper cable polarity Swap the fiber cables at the PM connector to reme
30. Magnum 6K16V are normally set factory default to operate in full duplex mode for best fiber distance and performance The 1000Mbps SC fiber optic module on the Gigabit SX and Gigabit LX transceivers are compatible with the IEEE 802 3z Gigabit standards There are two LEDs mounted on each Gigabit port module The Gigabit fiber port is fixed at 1000Mbps speed full duplex mode at all times and has LEDs that indicate LK Link status and ACT receiving activity on that port when lit 2 2 6 Packet Prioritization 802 1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network As a LAN device the Magnum 6K16V can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers The Magnum 6K16V switching hardware supports the IEEE 802 1p standard and fulfills its role in support of QOS giving packet processing priority to priority tagged packets according to the 802 1p standard In addition to hardware support for QOS the MNS software R2 supports two priority queues that can be shared across the eight levels of defined packet priorities for application specific priority control by the user through software configuration settings 2 2 7 Frame Buffering and Flow Control Magnum 6K16V s are store and forward switches Each frame or packet is loaded into the Switch s memory and inspected before forwarding can occur Thi
31. a security violation or an S Ring fault condition Vertical mounting for efficient convection cooling no fans extended temp Mounting brackets for vertical mounting are included DIN Rail mounting hardware is optional Ethernet signal and power cables attach in the bottom Two sets of status LEDs one set viewable at the port connector and one set viewable from the front Standard AC power input 48VDC or 24VDC or 125VDC input is optional Standard AC power input is IEC plug auto ranging for worldwide use For special applications models with 48VDC or 24VDC or 125VDC are available Dual Source DC input can also be selected and configured on the DC power input models Heavy duty design for Industrial Ethernet and extended temperature operation Fiber ports take more power than copper ports but the Magnum 6K16V design provides for this with heavy duty components The ambient temperature dual rating is 60 C per UL methods and 95 C per type test methods MNS 6K licensed Network Management Software included S Ring optional Release 2 5 fall 03 includes SNMP Switch Management with secure access control RMON CLI Port Security Port Mirroring Port Settings Control Telnet TFTP FTP support Spanning Tree Protocol Link Loss Leam S Ring with license key multi level QoS Port and tag based VLANs GVRP IGMP Snooping SNMPc GUI support Event Log SNTP client for time of day BootP and DHCP client for IP configuring and password se
32. asily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the IEEE 802 3z standard 1000Mbps distance limits i e 10 25 40 or 70Km at full duplex and depend upon the Gigabit modules used 1 1000Mb Fiber SC 2 100Mb SC The two Giga port has been offered as GBPM 2OTX fiber or RJ 45 whereas the single Gigabit module comes in flavor of G 4 10 100 RJ 45 ports or G 2 100Mb fiber ports as shown below in the above figure Each port has an Activity ACT LED indicating packets being received and a link LK LED indicating proper connectivity with the remote device when lit 5 2 12 6KM BLNK The 6K8 BLNK is a blank face plate or cover plate that must be installed in any empty 6K16V PM slot to maintain proper cooling air flow safety etc Two screws underneath the front panel hold the 6KM BLNK in place 47 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 6 0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments The installation of a Magnum 6K16V Switch is a straightforward procedure see INSTALLATION Section 2 6 the operation is also straightforward and is discussed in Section 4 Should problems develop during installation or operation this section is intended to help locate identify and correct these types of
33. ates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed if the LED is ON 100Mbps if it is OFF 10Mbps 5 2 1b 6KP4 F10ST 4 10Mb multi mode FX ST twist lock Module i es 38 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 The Magnum 6KP4 F10ST 6KP4 RJ1OMST is a 1OMb multi mode 4 Port 10Mb ST Fiber Port fiber module with 4 ST Fiber ports All four fiber a a ports are ST connectors ra ECO and configured as 10Mb 3 oS cae OF LOR Half duplex by default eg The 10Mb ST fiber ports allow the user to connect their legacy 10Mb network FULL HALF to the Magnum 6K16V switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as a special order Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and FDX HDX LED indicating full duplex mode when lit or half duplex if off 5 2 1c 6KP4 FLSTFX 2 10Mb amp 2 100Mb multi mode FX ST twist lock Module The Magnum 6KP4 6KP4 RJ1OMST FLSTEX is a combo fiber 4 Port 10Mb ST Fiber Port module with two 10Mb two 100Mb mul
34. cable when _ M 44 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 connecting to a hub or another switch The switch is configured as position by default settings from the factory the left most RJ 45 port is used for segments going to workstations and other user node device connections as other ports of the module For cascaded and up link connections i e a connection to another hub or switch typically the uplink switch should be in the OUT X position Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit a FDX HDX LED to indicate full duplex mode when lit or half duplex when off and a 10 100 LED indicating 100Mb when lit or 10 Mbps when off Important Note For the 6KP8 RJ45 Crossover Switch Inside is set for by default from the factory for the Port 1 and act similar as other user port The location of crosss over switch can be seen in the fig 3 5 2 c RJ 45 module at page no 27 The RJ 45 pins normally TP crossover switch are per the standard for hubs to users twisted pair wiring 1 receivet 2 receive 3 transmit 6 transmit other pins not used When the TP crossover push button is UP the pins of the RJ 45 port are per the standard for up links using twisted pair wiring i e the transmit and the receive pairs are exchanged 1 transmit 2 transmit 3
35. can send receive auto negotiation pulses and the second of the two connected devices is powered up i e when LINK is established for a port or the LINK is re established on a port after being lost temporarily e NOTE Some NIC cards only auto negotiate when the computer system that they are in is powered up These are exceptions to the negotiate at LINK enabled rule above but may be occasionally encountered When operating in 100Mb half duplex mode cable distances and hop counts may be limited within that collision domain The Path Delay Value PDV bit times must account for all devices and cable lengths within that domain For Magnum 6K 16V Fast Ethernet switched ports operating at 100Mb half duplex the bit time delay is SOBT 34 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 4 5 Flow control IEEE 802 3x standard Magnum 6K16V Switches incorporate a flow control mechanism for Full Duplex mode The purpose of flow control is to reduce the risk of data loss if a long burst of activity causes the switch to save frames until its buffer memory is full This is most likely to occur when data is moving from a 100Mb port to a 10 Mb port and the 10Mb port is unable to keep up It can also occur when multiple 100Mb ports are attempting to transmit to one 100Mb port and in other protracted heavy traffic situations Magnum 6K16V Switches implement the 802 3x flow control non blocking on Full
36. cscssesssssesescseeeee 50 APPENDIX B Internal DC Power Supply OptionsS scssssssssssseeees 51 APPENDIX C Internal DC Dual Source Power Option scsesseee 54 Revisions 06 04 New port modules has been added and updated on Alarm contacts 01 04 Added Section 3 5 Alarm Contacts and 3 7 1 Console Port pins 12 03 Updated Section 3 3 DIN Rail and Appendix B DC Power 10 03 Initial Release with Rev A Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 THE MAGNUM LINE Ethemet connectivity products Designed and Manufactured in the USA Overview GARRETTCOM INC OFFERS THE PREMIUM QUALITY MAGNUM LINE OF ETHERNET LAN CONNECTIVITY PRODUCTS WITH INDUSTRY STANDARD FUNCTIONALITY AND BUILT IN FIBER CONFIGURABILITY MAGNUM PRODUCTS ARE DESIGNED FOR USE IN DEMANDING CARRIER CLASS INDUSTRIAL GRADE AND OEM APPLICATIONS WHERE RELIABILITY IS A PRIMARY CONSIDERATION 6K SERIES MANAGED FIBER SWITCHES GIGABIT 100 AND 10 MBPS FIBER AND COPPER PORTS MIX AND MATCH FEATURES SFF FIBER AND DC POWER IN 1U UNITS 4K SERIES SWITCHES 100 AND 10 MBPS COPPER PORTS WITH OPTIONAL FIBER PORT WITH AUTO NEGOTIATING FULL SWITCHING PERFORMANCE QUAD SERIES FIBER SWITCHES 100 amp 10MBPS FIBER AND COPPER PORTS MIXED SPEED AND MIXED MEDIA TYPES FULL SWITCHING PERFORMANCE QUTDOOR ETHERNET SWITCH FOR TEMPERATURE UNCONTROLLED LOCATIONS 6 10 100 AND 2 100MB FIBER PORTS
37. cted without concern for AC power related problems or damage i es 23 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 to the unit Power supply options are available to suit the 6K16V Switches to special high availability communications and or heavy industrial grade applications including 48VDC 24VDC and 125VDC with single DC input 48VDC 24VDC and 125VDC with dual source DC input See the Appendices of this manual for more details Use an RFQ for other variations 3 5 Alarm Contacts for monitoring internal power and Software Traps The Alarm Contacts feature standard on Magnum 6K16V s provides two Form C Normally Closed NC contacts to which the user can attach two sets of status monitoring wires at the green terminal block When this option is present the terminal block for Alarm Contacts is part of the Power Input panel in the Magnum 6K16 s case The AC or DC power input connection is in the same panel A manual On Off Switch for power to the unit is not available on 6K16 units with the Alarm Contacts option as these two features occupy the same space in the case The first NC Alarm Contact top position is a Software Alarm operated by user settings in the MNS 6K software The user can disable the Software Alarm feature with a software configuration command if desired When the Software Alarm is enabled the Form C Normally Closed NC contact is held close during normal software operation A us
38. curity Web management is in beta test MNS 6K software is factory installed supported and updated via Internet and GCI FTP Server 14 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 2 4 Applications Magnum 6K16V Fiber Switches offer high performance modularity and availability They provide the flexibility of 100Mbps fiber and copper ports as well as single or dual Gigabit 1000Mb ports with industry standard LAN management software Magnum 6K16V Switches are easily used in a variety of applications including client server computing secure VLAN performance upgrades to departmental networks and stream traffic for VOIP and audio video applications or a very diversified combination of mixed media in Industrial floor applications The performance characteristic of the 6K16V Switches enables them to inter connect a series of subnets one subnet per 6K 16V Switch port in a LAN traffic center The subnet connections may be via fiber or twisted pair cabling 100Mbps or 10 Mbps speed and full or half duplex The mixed media modular capability is ideal for Industrial applications where existing Ethernet LAN networks where existing cabling must be accommodated The fiber built in media capability is ideal for integrating future proof fiber cabling into the LAN structure Example 1 Magnum 6K16V Switch for a Industrial application Equipped with lots of useful features hardened enclosure wide spread of AC DC power suppl
39. ded twisted pair cabling is 100 meters 328 ft Media IEEE Standard Connector Twisted Pair CAT 5E 1000BASE T RJ 45 NOTE Jt is recommended that high quality CAT 5E cables which work for both 100 Mb and 1000Mb be used whenever possible in order to provide flexibility in a mixed speed network 20 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 The following procedure describes how to connect a 1000BASE T twisted pair segment to the RJ 45 port The procedure is the same for both unshielded and shielded twisted pair cables 1 1000Base T connections require that all four pairs or wires be connected Insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established 3 2 6 Connecting Gigabit Media Using GBICs The Gigabit ports accept industry standard GBICs for user selection of the gigabit media type desired A selection of fiber and copper GBICs are available 3 3 DIN Rail Mounting The Magnum 6K16V is designed for use in a factory floor industrial environment It is available with optional DIN Rail brackets to mount it securely in a metal factory fl
40. dy this situation 3 2 2 Connecting Fiber Optic SC type Snap In The following procedure applies to installations using a PM with SC type fiber connectors i e using 6K MSC 6K SSC single mode When connecting fiber media to SC connectors simply snap on the two square male connectors into the SC female jacks of the 6KPM until it clicks and secures 3 2 3 Connecting Single Mode Fiber Optic When using single mode fiber cable be sure to use single mode fiber port connectors Single mode fiber cable has a smaller diameter than multi mode fiber cable 19 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 9 125 microns for single mode 50 125 or 62 5 125 microns for multi mode where xx xx are the diameters of the core and the core plus the cladding respectively Single mode fiber allows full bandwidth at longer distances and may be used to connect 10 Mb nodes up to 10 Km apart or 18Km with the 6K SSC The same procedures as for multi mode fiber applies to single mode fiber connectors Follow the steps listed in Section 3 2 2 above 3 2 4 Connecting Twisted Pair RJ 45 CAT3 CATS Unshielded or Shielded The RJ 45 ports of the Magnum 6K16V can be connected to the following two media types 1OOBASE TX and 1OBASE T CAT 5 cables should be used when making 100BASE TX connections When the ports are used as 1OBASE T ports CAT 3 may be used In either case the maximum distance for unshielded twisted pair cabling i
41. e sure to keep the shipping container should you need to re ship the unit at a later date To validate the product warranty please complete and return the enclosed Product Registration Card to GarrettCom Inc as soon as possible In the event there are items missing or damaged contact the party from whom you purchased the product If the unit needs to be returned please use the original shipping container if possible Refer to Section 6 Troubleshooting for specific return procedures Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 2 2 Product Description Magnum 6K16V Managed Fiber Switch Magnum 6K16V Managed Fiber Switches provide modularity of fiber and copper ports 1OMb 100Mb and Gigabit speed ports and comprehensive management software in a compact industrial grade package Setting a new standard for Industrial and Carrier Class applications heavy duty Ethernet Switch jobs are readily accommodated with an extended temperature rating of 40 C to 60 C by the UL Component Parts method or 50 C to 95 C by the IEC 60068 Type Test method With options such as all popular DC power input types worldwide AC power and DIN Rail mounting the hardened Magnum 6K16V is a go anywhere do anything Industrial Ethernet Switch The large family of port modules offer the choice of all fiber media all connector types multi and single mode and 10 100 Mb auto negotiating RJ 45 ports Standard GBIC ports can be configured
42. ed can be fixed using software commands Agency Approvals UL listed UL60950 cUL CE Emissions meet FCC Part 15 Class A NEBS L3 and ETSI compliant IEEE P1613 Environmental Standard for Electric Power Substations IEC61850 EMC and Operating Conditions Class C for Power Substations NEMA TS 2 and TEES for traffic control equipment Warranty Three years per UL 60950 temperature rating Made in USA NEBS Test Classification NEBS Compliant Email sales GarrettCom com for details Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 1 2 Ordering Information Magnum Managed Fiber Switch 16 ports max MODEL DESCRIPTION Magnum 6K16V Magnum 6K16V Managed Fiber Switch base unit for vertical mounting May be configured with a selection of 10 100 1000 6K16V fiber and copper port connector types 16 total ports max Two metal brackets for vertical wall or panel mounting Wire speed filtering and forwarding across all ports 802 3x flow control 802 1p priority packet processing self learning 4K node address table large 240KB packet buffers for 10 100 and 120KB for 1000Mb For licensed managed networks software MNS 6K and S ring See separate data sheets Magnum 6K16V 24VDC Same as 6K16V except the power input is 24VDC Magnum 6K16V 5VDC Same as 6K16V except the power input is 5VDC reg amp fused Magnum 6K16V 48VDC Same as 6K16V except the power input is 48VDC Magnum 6K16V 125VDC Same as 6K16V except the power input
43. eed copper ports The 4 Port 10 100Mbps and 2 100 Mb ST Fiber Port ST connector functions as a fiber optic transceiver to support 1OOBASE FX network segments When installed in a Magnum 6K16V Managed Switch the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic cable distances up the IEEE standard 100Mbps distance limits i e typically 2km at full duplex and 412m at half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed if the LED is ON 100Mbps if it is OFF 10Mbps 5 2 la 6KP6 RJ10ST 4 10 100Mbps RJ 45 and 2 10Mb multi mode FX ST twist lock Combo Module The 6KP6 RJ1OST is a six port combo module that looks similar to the 100Mb combo module with the exception of 10Mb speed at the ST fiber module The ST connector functions as a fiber optic transceiver to support 1 OBASE FX network segments When installed in a Magnum 6K16V Managed Switch the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic cable distances up the IEEE standard 10Mbps distance limits i e typically 2km at full duplex and half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indic
44. eeeeeeeceteeeeeeeeeneeeaes 40 5 2 4 6KP6 RJSSCL snap in Connector eee eeseeeeeeteceeeeeeeeeeeees 41 5 2 4a 6KP6 RJIOST twist lock connector ceeceseeteeeteeseeeees 41 5 2 5 6KP8 MTRJ icsse sireeni otteeseeen eieaa seai si 42 5 2 5a 6KP6 MT10ST ST Fiber port ccccccccscesceseeeeeeeseeseeseeseeeens 42 5 2 6 OKPE ASMIT eiee u apanan aieo i a aiana 43 5 2 7 C6 5d SoA Ut Cane eee ee ee 43 5 2 8 6KP8 45LC Combo Connector cccccceesceceesssseceessseeeeseeees 44 5 2 9 6KP8 RJ45 Twisted Pair 10 100Mb 8 Port ce eee 44 5 2 10 6KP8 45 2MT MTRJ Small Form Factor ccccccccessceeseeeees 45 5 2 10a 6KP8 45 2LC LC Small Form Factor 0 0 0 cccceescccsseeeseeeees 46 5 2 11 GBIC SXSC Gigabit fiber 1000Mb mm SC Connector 46 5 2 1la GBIC LXSC Gigabit fiber 1000Mb mm SC Connector 47 5 212 GREMEBLNE 5 esis sceieciececcntescaniees Heonsiaesebtnts stectieyscoisicrsigesevssantente nt 47 6 0 TROUBLESHOOTING wesc cccseciccsecescsssssocsessnseccvesesncsesenssacecctonvsesenves ecs 48 6 1 Before Calling for Assistance cccccccceccseescesseeesceeecesecesecneecneeeeeenes 48 6 2 When Calling for Assistance 0 ccccscceseesecesecsseeeceeeeeseeeneeneeeseeees 49 6 3 Return Material Authorization RMA Procedure ceseseeees 49 6 4 Shipping and Packaging Information cecceseeseesteereeeeeeeeeeeeees 50 APPENDIX A WARRANTY INFORMATION ccccccss
45. eo GarrettGonr Ethernet at Its Best Magnum 6K16V Managed Fiber Switch Hardware Installation and User Guide Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Magnum 6K16V Managed Fiber Switch Hardware Installation and User Guide Part 84 00125 Rev A Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories GarrettCom Magnum and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom Inc Important The Magnum 6K16V Managed Fiber Switch contains no user serviceable parts Attempted service by unauthorized personnel shall render all warranties null and void If problems are experienced with Magnum 6K16V Switch products consult Section 6 Troubleshooting of this User Guide Copyright 2004 GarrettCom Inc All rights reserved No part of this publication may be reproduced without prior written permission from GarrettCom Inc Printed in the United States of America Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Contacting GarrettCom Inc Please use the mailing address phone and fax numbers and email address listed below GarrettCom Inc 213 Hammond Ave Fremont CA 94539 Phone 510 438 9071 Fax 510 438 9072 Website http www GarrettCom com email support garrettcom com Federal Communications Commi
46. er brackets and four 2 56 flat head screws NOTE Every 6KPM Card package comes with their matching Daughter and Granddaughter board The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages Always install the PM module separately one by one to avoid the mixing Do not change the Blue color DIP Switch setting ever and leave it at factory default i as 25 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Step 2 Remove Chassis Cover The Magnum 6K16V chassis consists of top bottom front and rear parts and assembled together with the help of 18 Philips head screws There are 6 screws located on the front panel of the unit 2 each on top and the bottom and one each at the side 12 for top bottom cover of the unit 6 each on the bottom side of the unit and 6 screws each on the sides and 6 screws for the rear panel 2 each on top and bott0m and one each on the side Remove these screws Once these screws are removed the front panel is easily slid out to the front of the chassis base SarrettCom Figure 3 6 1a Removing the CC WM Front panel from the unit Caution Be careful not to disturb the power supply Once the front panel is removed the front cover may be slid out to the front of the unit Hold on the back part and then carefully and slowly slide out the top chassis cover towards the front side as shown in the picture When the chassis top cover
47. er defined software malfunction such as an SNMP Trap or a Software Security violation or an S Ring Fault causes the contact to open and thus trigger an alarm in the user s monitoring system The second bottom position NC Alarm Contact is held close when there is power on the main board inside of the 6K16 This provides a Hardware Alarm because the NC contacts will open when internal power is lost either from an external power down condition or by the failure of the power supply inside of the Magnum 6K16 Switch Useful info about Alarm contacts 1 There is four terminal block 1 2 3 4 provided next to AC DC power supply 2 The top two pins 1 2 are software operated 3 The bottom two pins 3 4 are hardware operated 4 By default it is NC normally closed 5 The software operation need to be enable and set to get the Alarm traps For detail information about the Software Alarm and software control of SNMP alarm traps please jug reference the Magnum MNS 6K Software User Manual Chapter 19th The Alarm Contacts are on the front left area next to the DC power source of the Magnum 6K16V unit and is green in color as shown in the picture Relay Contacts 24 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 3 6 6K16V Port Module 6KPM Installation Note the modules used in the 6K16V vertical mount unit are similar to those used in rack mount 6K units except that the top LEDs are positioned f
48. fering and processing resumes This flow control sequence occurs in a small fraction of a second and is transparent to an observer Another feature implemented in Magnum 6K16V Switches is a collision based flow control mechanism when operating at half duplex only When the Switch detects that its free buffer queue space is low the Switch prevents more frames from entering by forcing a collision signal on all receiving half duplex ports in order to stop incoming traffic 2 2 8 Managed Network Software MNS 6K for Magnum 6K16V Magnum 6K16V s come with licensed MNS 6K software which allow to configure the Magnum 6Ks as a Managed Switch and other Software enabled features For additional information about MNS 6K see the Magnum 6K16V MNS Software User guide in pdf format a separate document normally accessed via your web browser at ftp ftp garrettcom com or FTP client program by ftp GarrettCom com using user m6kuser password m6kuser All MNS 6K software information including new releases and upgrades related to MNS 6K software can be accessed and download from GarrettCom s FTP site Alternatively for documentation and general information visit www GarrettCom com techsupport index htm software and look for Magnum 6K16V s MNS 6K info or email support GarrettCom com for further information 13 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 2 3 Features and Benefits Managed sw
49. has been removed the interior of the unit is exposed Looking down into the Magnum 6K16V unit notice that there are individual PM installation spaces and female latch white connectors provided on the main board along with four stand off s for each 6KPM card position See Figure 3 6 1b Figure 3 6 1b Magnum 6K16V Top view without chassis cover Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Step 3 Remove front panel face plate retaining screws There are two PM slots A B located on the front of the chassis cover Looking into the vertical placed Chassis cover of the unit there are three brackets with retaining screws 256 flat head which hold each PM Face plate card slot securely These six screws shown in the picture below are used to secure a PM face plate in position but unscrew only four of the screws as shown in Fig below These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables See Figure 3 6 1c Figure 3 6 1c Top View 6KPM retaining screws hold Face Plate 3 6 2 Installing 6KPM Cards in the Magnum 6K16V Up to two front mounted 6KPM cards may be installed in one Magnum 6K16V Managed Fiber Switch unit Follow these steps to install a 6K PM Step 1 Remove top chassis cover See procedure in Section 3 6 1 above Step 2 Placed Granddaughter board as shown in fig 3 6 2a and 3 6 2b on the chassis b
50. it 1000Mb module option 6KP5V G4RJ G 2 module w one GBIC transceiver and four 10 100 RJ 45 connectors 6KP3V G2SC G 2 module w one GBIC transceiver and two 100Mb 2km FX SC i M 4 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 fiber ports connector GBPM 20TX Two port Gigabit 6K module for 6K16V Switches provides two GBIC open transceiver port for a user selectable GBIC transceiver module GBPM COTX One slot Gigabit 6K module for 6K16V Switches uses one 6K16V slot and provides one GBIC open transceiver port for a user selectable GBIC transceiver module GBIC SXSC GBIC transceiver module for use in GBPM xOTX one 1000BASE SX port with mm SC fiber connector GBIC LXSC10_ GBIC transceiver module for use in GBPM xOTX one 1000BASE LX LH port with 1310nm sgl mode SC 10km fiber connector GBIC LXSC25_ GBIC transceiver module for use in GBPM xOTX one 1000BASE LX LH port with 1310nm sgl mode SC 25km fiber connector GBIC LXSC40_ GBIC transceiver module for use in GBPM xOTX one 1000BASE ZX port with 1550nm sgl mode SC 40km fiber connector GBIC transceiver module for use in GBPM COTX one LX port with mm SC fiber connector GBIC LXSC70_ GBIC transceiver module for use in GBPM xOTX one 1000BASE ZX port with 1550nm sgl mode SC 70km fiber connector GBIC TP GBIC transceiver module for use in GBPM xOTX one 802 3ab 1000BASE T port RJ 45 connector CONSOLE CBL Industry standard serial cable
51. itching for high performance Ethernet LANs Magnum 6K16V Switches provide non blocking all ports can run at full speed at once performance with standard Managed Networks Software MNS 6K included They are typically used in LAN traffic centers with 16 100Mb or 8 2 Gigabit ports for backbone connections where managed network services are desired Switching services includes 802 1p QoS packet prioritization The Magnum 6K16V switching hardware supports QoS giving packet processing priority to priority tagged packets according to the IEEE 802 1p standard For port and application specific priorities the QoS software may be configured by the user Features Fiber Built In Magnum 6K16V Managed Fiber Switches are designed to naturally include fiber ports and support mixes of multi mode and single mode 10 Mb 100Mb and 1000Mb speed full and half duplex classic Small Form Factor SFF and GBIC fiber connectors RJ 45 10 100 ports can also be configured in the mix of port types S Ring and Link Loss Learn for reliable high availability using ring topology S Ring along with the Link Loss Learn feature provides reliable fast recovery of a fault in a ring topology Relay Contacts for monitoring internal power and user defined software events Two Alarm Relay contacts monitor basic operations One is for hardware and will signal loss of power internally The other is software controllable and will signal user defined software events such as
52. le for connection to a earthing wiring Use only with Listed 10 A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent RWN gt m Fastening torque of the lugs on the terminal block 9 inch pound max 6 Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rac k at least 4 inches apart with the first one located within 6 inches of the terminal block B5 0 OPERATION Operation of Magnum 6K16V Switches with the optional 48 VDC 24VDC and 125VDC power supply is identical to that of the standard AC powered models B6 0 ORDERING INFORMATION To order the optional 48VDC power supply factory installed add a suffix of 48VDC after the product s standard model Example Magnum 6K16VR 48VDC Similarly to order the optional 24VDC or 125VDC industrial specific power supply factory installed add a suffix of 24VDC or 125VDC after the product s standard model Example Magnum 6K16V 24VDC Magnum 6K16V 125VDC B7 0 TROUBLESHOOTING Please refer to Section 6 0 for troubleshooting 53 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 APPENDIX C Internal DC Dual Source Power Option C1 0 SPECIFICATIONS FOR MAGNUM 6K16V FIBER SWITCH Power Supply Internal 48VDC Dual Source model Dual Src 48V DC Power Connector First Source A 7 oa 2nd Source
53. le that is within six feet 2 meters of the intended Magnum 6K 16V site The rugged metal case of the Magnum 6K16V will normally protect it from accidental damage in a lab or workplace setting Maintain an open view of the front to visually monitor the status LEDs Keep an open area around the unit so that cooling can occur from convection while the unit is in operation The 6K16V has no fans so it is silent when in operation Internal electronics use the case as a heat sink so the unit may normally be quite warm to the touch 3 2 Connecting Ethernet Media The Magnum 6K16V Switches are specifically designed to support all standard Ethernet media types within a single Switch unit This is accomplished by using a family of different port Modules which can be individually selected and configured per port See Section 2 4 for a description of the PMs The various media types supported along with the corresponding IEEE 802 3 and 802 3u standards and connector types are as follows 18 Installation and User Guide 06 04 Magnum 6K16V Managed Fiber Switch IEEE Standard Media Type Fiber 100BASE FX mm Fiber sgl m2 Fiber 100BASE FX mm Fiber sgl m2 Fiber small form factor mm Fiber small form factor sgl m Fiber Copper 10BASE T and 100BASE TX twisted pair 1 mm multi mode 3 2 1 Max Distance Port Module 220m ft GBIC SXSC 5Km GBIC LXSC 2 0km 6 562 ft 6K6 MSC MST 18 0km 95K ft SSC SSCL 2 0km 6 562 ft 6K8 MTRJ M
54. lti mode 50um cable 550m 1000BASE LX full duplex single mode 62 5um cable 5Km Fiber Multi mode connector types supported Fiber Port ST type twist lock Fiber multi mode 10Mb 10BASE FL Fiber Port MTRJ type plug in SFF Fiber multi model100BASE FX Fiber Port SC type snap in Fiber optic multi mode 100BASE FX Fiber Port ST type twist lock Fiber optic m mode 100BASE FX Fiber Port 1OOOBASE FX GBIC modules i es 1 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Fiber Single mode connector types Fiber Port SC type Fiber optic single mode 100BASE FX Fiber Port LC type Fiber SFF single mode 100BASE FX Fiber Port 1OOOBASE FX GBIC modules LEDs Per Port one set at the port one set in top or front LK Steady ON when media link is operational ACT ON with receiver port activity FDX HDX ON Full Duplex Mode OFF Half Duplex Mode 100 10 ON 100Mbps speed OFF 10 Mbps Operating Environment Ambient Temperature 40 to 140 F 40 to 60 C for UL60950 and Component Parts rating 60 to 205 F 50 to 95 C for IEC 60068 Type Test short term rating Storage Temperature 60 to 210 F 50 to 100 C Ambient Relative Humidity 5 to 95 non condensing Altitude 200 to 13 000 ft 60 to 4000m Conformal Coating humidity protection option Request quote Alarm Relay Contacts One NC indicating internal power one NC software controllable Packaging Enclosure Rugged High
55. mbo module with copper and fiber Small Form Factor MTRJ type ports The small size of MTRJ connectors give an advantage of placing more ports on one module The 6KP8 45MT is equipped with 4 10 100 RJ 45 ports and 4 MTRJ fiber a 6 8 i ports G LINK 10 100 When installed in a Magnum 6K16V GB ACTIVITY Q FULL HALF Switch it supports the standard distances as mentioned on 5 2 3 and the LEDs also act similarly 5 2 7 6KP8 MLC 8 ports 100Mbps multi mode LC connector Small Form Factor Magnum 6KP8 MLC is a eight port multi mode fiber LC connector small form factor used primarily in 6KP8 MLC 100Mbps fiber to the desktop 8 Port 100Mbps multi mode LC fiber port links When installed in a Magnum 6K16V Switch it supports fiber optic cable distances up to the IEEE standard 100Mbps distance limits i e typically 2km at full duplex and 412m at half duplex GB LINK LC Connector reduces the size of wiring panels in wiring closets while providing the The compact size of the advantage of future proof fiber optic technology The cable end is a plug in connector with both fiber strands terminated in one housing that cannot be improperly inserted Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with www GarrettCom com 43 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 the remote device when lit and a
56. module and the two fiber ports operate at 100Mbps full duplex default User mode control per port through the MNS software is also the same On Magnum 4 2 Combo modules there are four LED s for each RJ 45 port which indicate status the same as described for the 6K8 RJ45 in Section 2 2 3 above The fiber port s LEDs indicate status the same way as described for the SFF fiber modules in Section 2 2 2 above Color coding on the panel of the module shows which LEDs belong to which port The Magnum Combo six port modules are also available with 4 MTRJ 100Mb mm SFF fiber and 2 10Mb fiber mm ST ports and with 4 RJ45 10 100 copper and 2 10Mb fiber mm ST ports The 4 RJ 45 2 10 Mb ST operation of the SFF fiber and the RJ 45 half of the module is as described for those port types above For detailed information about 10Mb mm ST fiber half of the module see Section 2 2 5 10 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 2 2 4 Four Port 10 Mb and 100Mb mm Fiber ST Modules 1 CIO a Bove TX ELK RX _TX BLK RX nt CID E TX ELK RX The 4 port 10Mb ST fiber modules behave the same as the 4 100Mb ST fiber modules except for the 10Mb speed For ports numbering ports 1 2 5 6 are present ports 3 4 7 8 are not present There is also a similar 100Mb fiber SC module The default setup on the 10Mb fiber module is half duplex which allows the Magnum 6K16V Switch to connect to any 10Mb hub or
57. nal power supply because of the blocking action of the diodes This is true even if one input connection is reversed while the Switch is operating from the other source e The Switch will not receive power and will not work when both inputs are simultaneously absent or are both incorrectly connected C5 0 INSTALLATION This section describes the proper connection of the 48VDC 24VDC and 125VDC dual source leads to the 48VDC 24VDC amp 125VDC power terminal block on the Magnum 6Ks Switch shown in Figure The 48VDC terminal block on the Magnum 6K16V Switch as shown in Fig C5 0 is located on the right rear of the unit and is equipped with five 5 screw down lead posts If it is the reverse model it is located on the left rear The primary terminals are identified as positive A negative A and the secondary power terminals as negative B positive B The chassis earth or ground GND is a threaded post with a 6 nut The Dual Source terminal block for the 24VDC and 125VDC are similar Figure C5 0 48VDC Dual Source wiring connections to the External Terminal Block on a Magnum 48VDC with Dual Source option 36 70VDC 36 70VDC GND Note The GND should be hooked up first The 6K16V unit has a floating ground so the user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the o
58. om the panel or wall behind it creating a rear space of about 1 4 inch or 1cm This allows air circulation and cooling of the rear part of the case Since the 6K16V uses special internal thermal techniques patent pending to move the heat generated by the electronic components inside into the case the case may be quite warm to the touch during normal operation The unit can be mounted using the brackets turned outside normal or inside if space is tight Attach the mounting bracket either outside or inside as shown in the illustration above dotted line shown for the brackets inside The spacing for the mounting screws imto the supporting wall or panel is a rectangle 11 89 x 7 85 center to center 3 4 Powering the Magnum 6K16V Managed Fiber Switch The Magnum 6K16V Switches incorporate an internal universal power supply and have a recessed male IEC connector for the AC power cord at the left rear A manual power ON OFF switch is adjacent A six foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada The auto ranging power supply supports installation environments where the AC voltage is from 90 to 260 volts with a power input frequency between 47 and 63 Hz The 16 port units will consume over 20 watts of power typically When connecting the Ethernet cabling there is no need to power down the unit Individual cable segments can be connected or disconne
59. ons Remove the 6K16V PM s from the shipping container Be sure to keep the shipping container should you need to ship any of the PMs separately at a later date In the event there are items missing or damaged contact your supplier If you need to return the unit use the original shipping container if possible Refer to Chapter 5 for specific return procedures 5 2 6KPM Module Description An important feature of the Magnum 6K16V is the use of Port Modules for flexible mixed media connectivity to RJ 45 and fiber media Since the Magnum 6K16V Switches have dual speed capability for copper ports the 6 or 8 port interfaces are designed to support all standard Ethernet media types at 10 or 100Mps speed Each 6K16V PM provides six or eight ports for connecting Ethernet segments with its individual connector type and media For a list of 6K16V Port Module types refer to Section 1 2 Each 6K16V PM is individually described in the following sections NOTE The port 1 on the RJ 45 ports on all the modules either all RJ 45 ports or used for COMBO module is set as other user ports 37 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 5 2 1 6KP6 RJMST 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX ST twist lock Combo Module The Magnum 6KP6 RJMST is a combo 6 port module of RJ 45 s at 10 100Mbps and fiber optic ports at 100MB The Combo module is equipped with dual mode ST type connectors and 6KP6 RJMST dual sp
60. oor enclosure maintained vertically for proper convection cooling of the unit The Magnum 6K16V requires two DIN Rail mounting clips or latches for secure mounting and these may be ordered as Model DIN RAIL VRM See a 6K16V viewed from the rear at right with model DIN RAIL VRM in place on the unit The Din Rail Latching clips are mounted on the upper rear corners of the 6K16V unit Two threaded holes are provided on the sides of 6K16V for DIN Rail mounting purposes See side view at the left with the top of the unit pointed to the right The required two screws are included with the DIN Rail brackets and are no 10 32 X 3 8 PHIL PAN w star washer The two heavy duty Din Rail latches are designed so that they can be manually accessed from the top when the 6K16V is installed on a DIN Rail To install the 6K16V with the DIN Rail brackets and latches attached to it hold the 6K16V in the vertical position with the bottom out and with the top moved in toward the DIN Rail Position the latches over the top of the DIN Rail Then snap the latches 21 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 into holding position by moving the bottom of the 6K16V inwards to a vertical position The DIN Rail latches and brackets are heavy duty and will hold the 6K16V securely in position even with cabling attached to the unit To release the 6K16V from the DIN Rail mounting press the top of the two DIN Rail latches
61. or email to support garrettcom com When calling please have the following information readily available Name and phone number of your contact person Name of your company institution Your shipping address Product name Serial Number or Invoice Number Packing List Number or Sales Order Number Date of installation Failure symptoms including a full description of the problem _ M 49 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 GarrettCom will carefully test and evaluate all returned products will repair products that are under warranty at no charge and will return the warranty repaired units to the sender with shipping charges prepaid see Warranty Information Appendix A for complete details However if the problem or condition causing the return cannot be duplicated by GarrettCom the unit will be returned as No Problem Found GarrettCom reserves the right to charge for the testing of non defective units under warranty Testing and repair of product that is not under warranty will result in a customer user charge 6 4 Shipping and Packaging Information Should you need to ship the unit back to GarrettCom please follow these instructions 1 Package the unit carefully It is recommended that you use the original container if available Units should be wrapped in a bubble wrap plastic sheet or bag for shipping protection You may retain all connectors and this Installation Guide
62. or front viewing for the vertical mount 6K 16V model The modules have the letter V in the model numbers but otherwise are the same In the Port Module materials below all modules are referred to as 6KPM for convenience in describing port module installation Magnum 6K16V Switches are normally received from the factory with all required 6KPM modules installed There may be situations where 6KPM cards need to be added or replaced In cases where additional 6KPM cards are needed the faceplate for an available front mounted slot must be removed The following procedure describes this operation 3 6 1 Preparation for Installing and Removing 6KPMs STOP Be sure the power cord is unplugged from the chassis before attempting to remove and or replace any PM cards Failure to do so may result in damage to the unit and will void the warranty Caution Avoid Static Discharge The port modules like most electronic equipment are sensitive to static discharge Use proper ESD measures when handling port modules Step 1 Make sure the 6KPM Card package has all necessary accessories to install it properly Each 6KPM Card package except the Gigabit for field installation contains Daughterboard Bigger and Granddaughter board smaller three 5 8 stand offs for Granddaughter board 6 standoff for daughter Board nine 4 40 Pan Head screws along with Front panel face plate package The Front panel faceplate package includes 2 retain
63. ould be replaced Make sure the chassis cover is aligned properly before securing the enclosure 3 6 3 Removing 6KPM Cards To properly remove a 6KPM card from the 6K16V Managed Fiber Switch follow the 3 steps below Step 1 Remove chassis cover See procedures in Section 3 6 1 above Caution Be sure the power cord is unplugged Step 2 Remove retaining screws placed on top for the 6KPM and Face Plate On the top of the daughter module there are six retaining screws for each 6KPM card These screws are used to secure a 6KPM card in position see Figure 3 6 3a Remove the three standoffs holding the Granddaughter board with the chassis The screen faceplate screws out from the inside front of the chassis cover by loosening the 4 screws and bracket while holding it down firmly Figure 3 6 3a Top View 6 retaining s crews shown by arrows Step 3 Remove 6KPM Card Carefully and gently pull out the daughter board from the latching connectors using both hands gripping the board near the latch up connectors as shown in Fig 3 6 3b If the now empty slot is to remain unused be sure to install a 6KPM BLNK face plate cover Figure 3 6 3b Removing a 6KPM Card If another 6KPM card is replacing the one that has been removed follow the steps as described for installing a 6K PM card discussed in Section 3 6 1 30 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 3 7 Connecting a Management Con
64. parate line item following the product model Example Magnum 6K16VR 48VDC Dual Src 48V for the regular DS model with no ON OFF switch or Dual Src48V SWITCH with the ON OFF manual switch Similarly order the Dual source 24VDC or Dual source 125VDC as a separate line item following the product model Example Magnum 6K16VR 24VDC or Magnum 6K16VR 125VDC Dual Sre24V for regular models with no ON OFF switch Or Dual Sre125V Switch for models with the ON OFF switch OPERATION Operation of the Dual Source Magnum 6Ks 48VDC 24VDC and 125VDC Switch models are identical to that of the standard models 56
65. problem continues after completing Step 4 above contact your supplier of the Magnum 6K16V Switch unit or if unknown contact GarrettCom Inc by fax phone or email support garrettcom com for assistance 48 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 6 2 When Calling for Assistance Please be prepared to provide the following information l A complete description of the problem including the following points a The nature and duration of the problem b Situations when the problem occurs c The components involved in the problem d Any particular application that when used appears to create the problem 2 An accurate list of GarrettCom product model s involved with serial number s Include the date s that you purchased the products from your supplier 3 It is useful to include other network equipment models and related hardware including personal computers workstations terminals and printers plus the various network media types being used 4 A record of changes that have been made to your network configuration prior to the occurrence of the problem Any changes to system administration procedures should all be noted in this record 6 3 Return Material Authorization RMA Procedure All returns for repair must be accompanied by a Return Material Authorization RMA number To obtain an RMA number call GarrettCom Customer Service at 510 438 9071 during business hours in California
66. ptions B1 0 SPECIFICATIONS FOR MAGNUM 6K16V SWITCHES DC POWER Power Magnum 6K16V models for 48V and 24V DC amp 125VDC and 5V Power input Each Magnum Model 6K16V Managed Switch DC option requires a DC power source from for 24VDC 48VDC and 125VDC option or 5VDC input The wide range of power input qualifies this product for use in 24VDC 48VDC as well as 125VDC or 5VDC environments The 24VDC 48VDC or 125VDC or 5VDC power input provides an Ethernet networking product utilizing a special type of power supply with a proven high reliability record to fulfill the DC requirement DC Power Terminals internally floating GND Terminal for earth or ground wire connection to the 6K16V chassis Input Voltage 18 to 36 VDC 24VDC Input current 1 2Amps max for all RJ 45 ports Input current 2 4Amps max for all Fiber ports Input Voltage 36 to 70 VDC 48VDC Input current 0 8Amps max for all RJ 45 ports Input current 1 2Amps max for all Fiber ports Input Voltage 115 to 150 VDC 125VDC Input current 0 3Amps max for all RJ 45 ports Input current 0 35Amps max for all Fiber ports Power Consumption 50 watts max for fully loaded fiber ports 24V 48V 125V DC 30 watts typical for all RJ 45 Ports Input Voltage 5VDC or 5 SVDC Input current 3 5Amps max for all RJ 45 ports Input current 8 0Amps max for all Fiber ports Power Consumption 20 watts max for fully loaded
67. rol 12 2 2 8 Managed Network Software MNS 6K for Magnum 6K16V 13 2 3 Features and Benefits 00 ceeeesseeeecrseaeescsseaeeecsseaeeecaseaeaeeaeees 14 24 Applications s 2 ssccsstoieees ieee enn nies Osetia eeieids 15 3 0 Installation scccsssssscsssssssssesscsecsssscssssesssssssesssssssssssessessssessessnsnseeses 18 3 1 Locating Magnum 6K16V Switches ce ceeeeseeeceeeeeeeeeneeeeeneeeees 18 3 2 Connecting Ethernet Media 0 ee ec eeceseceseeecneeeeceeeeeceaeeeeeeecaeeereneees 18 3 2 1 Connecting Fiber Optic ST type twist lock 19 3 2 2 Connecting Fiber Optic SC type Snap In oo eeeeeeeeeeees 19 3 2 3 Connecting Single Mode Fiber Optic ceccecesseesseeteeteeteeees 19 3 2 4 Connecting Twisted Pair RJ 45 CAT3 CAT5 eee 20 3 2 5 Connecting Twisted Pair CATSE or better cceeeeeeereee 20 3 2 6 Connecting Gigabit Media Using GBICs eee eeeseeseeeeeneees 21 3 3 DIN Rail Mounting cececcesecsceesceeeeeeeeeeeceeeeseceseceseeeaeceeeeaeenaeenaes 21 3 3 1 Mounting Dimensions for 6K16V with metal brackets 22 3 4 Powering the Magnum 6K16V Managed Fiber Switch 0 23 3 5 Alarm Contacts for monitoring internal power and Software Traps 24 3 6 6K16V Port Module 6KPM Installation eee eeeseereereeeeeees 25 3 6 1 Preparation for Installing and Removing 6KPMG ccceeeeeeee 25 3 6 2 Installing 6KPM Cards in the Magnum 6K16V ossee 27 3 6 3 Removing 6KPM Cards
68. rtion loss Worst case distance Worst case OPB in dB Cable Loss in dB Km where the Cable Loss for 62 5 125 and 50 125um M m is 2 8 dB km and the Cable Loss for 100 140 Multi mode is 3 3 dB km and the Cable Loss for 9 125 Single mode is 0 5 dB km and the Cable Loss for 9 125 Single mode is 0 4 dB km LXSC25 and the Cable Loss for 9 125 Single mode is 0 25 dB km LXSC40 and the Cable Loss for 9 125 Single mode is 0 2 dB km LXSC70 The following data has been collected from component manufacturer s Agilent s and Lucent web sites and catalogs to provide guidance to network designers and installers i es 35 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Fiber Std Port km Module 3 fdx a 6KP4V 10Mb Multi 950 62 5 125 15 F10ST Mode e 19 5 5 9 23 5 50 125 19 5 3 4 13 5 6KPV 100Mb Multi 1300 62 5 125 20 31 9 0 3 0 ma Msc FX mode oa 50 125 23 5 31 ihe 5 Pa 00Mb Single 18 6KPV loxry ssc x mode 0 4 1300 9 125 15 31 Hans m Single 40 6KPV mode 0 4 1300 9 125 32 5 SSCL Bev Multi 1300 62 5 125 31 9 0 3 0 15 8 mode 50 125 23 5 31 5 5 2 0 12 2 mode SEE a b Multi 1300 62 5 125 17 5 5 mode 50 125 Single 1300 9 125 20 8 5 17 10 5 21 LXSC10 Tds z Pona lon Single 1550 9 125 21 37 5 17 5 LXSC25 lee GBIC 1000Mb Single 155
69. s technique ensures that all forwarded frames are of a valid length and have the correct CRC i e are good packets This eliminates the propagation of bad packets enabling all of the available bandwidth to be used for valid information While other switching technologies such as cut through or express impose minimal frame latency they will also permit bad frames to propagate out to the Ethernet segments connected The cut through technique permits collision fragment frames which are a result of late collisions to be forwarded which add to the network traffic Since there is no way to filter frames with a bad CRC the entire frame must be present in order for CRC to be calculated the result of indiscriminate cut through forwarding is greater traffic congestion especially at peak activity Since collisions and bad packets are more likely when traffic is heavy the result of store and forward operation is that more bandwidth is available for good packets when the traffic i O IU 12 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 load is greatest When the Magnum 6K16V Switch detects that its free buffer queue space is low the Switch sends industry standard full duplex only PAUSE packets out to the devices sending packets to cause flow control This tells the sending devices to temporarily stop sending traffic which allows a traffic catch up to occur without dropping packets Then normal packet buf
70. s 100 meters 328 ft Media IEEE Standard Connector Twisted Pair CAT 3 4 5 10BASE T RJ 45 Twisted Pair CAT 5 100BASE TX RJ 45 NOTE Itis recommended that high quality CAT 5 cables which work for both 10 Mb and 100Mb be used whenever possible in order to provide flexibility in a mixed speed network since dual speed ports are auto sensing for either 10 and 100Mb s The following procedure describes how to connect a 10BASE T or 100BASE TX twisted pair segment to the RJ 45 port The procedure is the same for both unshielded and shielded twisted pair cables 1 Using standard twisted pair media insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established 3 2 5 Connecting Twisted Pair CATS5E or better Unshielded or Shielded The RJ 45 Gigabit ports of the Magnum 6K16V can be connected to the media types 1 OOOBASE T or CAT 5E or better 100 ohm UTP or shielded twisted pair STP balanced cable The CAT 5E or better 100 ohm UTP or shielded twisted pair STP balanced cable is recommended to use when making 1000BASE TX connections In either case the max distance for unshiel
71. sole Terminal to Magnum 6K16V Use a DB 9 null modem cable use on any serial port or one DB 9 and one USB USB port on the laptop null modem cable to connect the Magnum6K16V Console Port the RS 232 port on the 6K16V Switch to the your PC so that your PC becomes the 6K16V s Console Terminal Note A console cable either of the two types may be purchased as a separate item with the 6K16V unit They are not bundled with the unit Console Com Mn avn Enlarged view of Magnum 6K16V Console Port area Note For a detailed description of Managed Network Software MNS 6K and Magnum 6K16V Switch configuration for Network Management please refer to Magnum 6K16V Software Manual available on GarrettCom s FTP site Some info about the MNS 6K software is available in Section 2 2 9 of this manual 3 7 1 RS 232 DB 9 Console Com port Serial port pin assignments DB 9 Console port connector Pin Signal Description 1 CD Carrier detect not used 2 RXD Receive Data input 3 TXD Transmit Data output 4 open not used 5 GND Signal Ground 6 9 open not used The above provided information enables a management station a PC or Console terminal to connect directly to the Switch Console using a straight through cable www GarrettCom com 31 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 4 0 OPERATION This chapter describes the functions and operation of the Magnum 6K16V Switch
72. ssion Radio Frequency Interference Statement Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference in a residential installation This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instructions may cause harmful interfernce to radio communications However there is no guarantee that interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into n outlet on a ccircuit different from that to which the recei
73. te 10OMbps 100Mbps and 1000Mbps Address Table Capacity 4K node self learning with address aging Packet buffer size 240KB for 10 100 and 120KB for 1000Mb Latency 5 us packet time 100 to 100Mbps 15 us packet time 10 to 10 Mbps and 10 to 100Mbps Network Standards and Compliance hardware Ethernet V1 0 V2 0 IEEE 802 3 1OBASE T IEEE 802 3u 100Base TX 10OBASE FX IEEE 802 3z 1OOOBASE TX Ethernet Auto Negotiation IEEE 802 3ab 1OOOBASE TX Ethernet IEEE 802 1p Priority protocol IEEE 802 1d Spanning tree protocol IEEE 802 1q VLAN Tagging IEEE 802 3x Flow Control Maximum 10 Mbps Ethernet Segment Lengths Unshielded twisted pair 100 m 328 ft Shielded twisted pair 150 m 492 ft 10BASE FL multi mode fiber optic 2 km 6 562 ft 10BASE FL single mode fiber optic 10 km 32 810 ft Maximum Standard Fast Ethernet Segment Lengths 10BASE T CAT 3 4 5 UTP 100 m 328 ft 100BASE TX CAT 5 UTP 100 m 328 ft Shielded twisted pair 150 m 492 ft 100BASE FX half duplex multi mode 412 m 1350 ft 100BASE FX full duplex multi mode 2 0 km 6 562 ft 100BASE FX half duplex single mode 412 m 1350 ft 100BASE FX full duplex single mode 20 0 km 66K 16V ft 100BASE FX full duplex Long Reach 40 0 km 122K ft Maximum Standard Gigabit Ethernet Segment Lengths 1000BASE T CATSe or higher is recommended 100 m 328 ft 1000BASE SX full duplex multi mode 62 5um cable 220m 1000BASE SX full duplex mu
74. the operation of the network such as occasional multi cast packets are forwarded to all ports The Magnum 6K16V Switches operate in the store and forward switching mode which eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the network Address Learning All Magnum 6K16V units have address table capacities of 4K node addresses suitable for use in larger networks They are self learning so as nodes are added removed or moved from one segment to another the 6K16V Switch automatically keeps up with node locations An address aging algorithm causes least used addresses to fall out in favor of frequently used addresses To reset the address buffer cycle power down and up i O U 32 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 4 2 Status LEDs For all Magnum 6K16V models PWR Power LED ON when external power is applied to the unit LK Steady ON Link status for 10 Mbps and 100Mbps operation ACT ON with port activity for 10 Mbps and 100Mbps operation F H Full Half duplex LED ON when the port is running full duplex OFF for half duplex 100 10 Speed LED ON when the speed is 100Mbps OFF when the speed is 10 Mbps 4 3 Up link Manual Switches set as for RJ 45 port only The module has a manual Up link switch located on the inside of the board next to the 10 100Mb 6K8 RJ45 port 1 which it controls It enables the port s cable
75. through set up of the software See Magnum 6K16V MNS Software Manual for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices There are three LED s per fiber port The Link LK LED indicates ready for i es 8 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 operation on that port when lit the F H LED indicates operation in full duplex mode when ON half duplex when OFF and the blinking ACT LED indicates receiving Activity on the port A fiber cable must be connected into a SFF port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port 2 2 2 Eight Port Copper Module 6K8 RJ45 The 6K16V s 8 port Copper port module model 6K8 RJ45 provides eight 10 100Mb switched RJ 45 ports The 10 100Mb switched ports normally as a default setting are independently N way auto negotiating for operation at 10 or 100Mb speed in full or half duplex mode i e each independently selects a mode and speed to match the device at the other end of the twisted pair cable See Section 4 3 for auto negotiation details On the model 6K8 RJ45 module there are four LEDs for each port two in the connector and two separate The LK Link LED indicates ready for operation on that port when lit The blinking ACT Activity LED indicates
76. ti mode fiber module and in combine 4 ST Fiber ports 3 n ELK Z QI k IG All four fiber ports are ST d 2 TX GLK RX connectors and configured as 10Mb Half duplex by default for 10Mb fiber and FULL HALF 100Mb Full duplex for the 100Mb fiber The 10Mb ST fiber ports allow the user to connect their legacy 10Mb network to the Magnum 6K16V switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports Whereas the 100Mb ST ww GarrettCom com 39 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 module allow to connect the 100Mb demand of Switch devices It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as a special order Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and FDX HDX LED indicating full duplex mode when lit or half duplex if off 5 2 2 6KP6 RJMSC 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX SC snap in Fiber connector The Magnum 6KP6 6KP6 RJMSC 4 Port 10 100Mbps and 2 100 Mb SC Fiber Port RJMSC is also a Combo 6 Port p module equipped with 4 10 100Mb RJ 45 ports along with 2 multi mode 100Mbps fiber optic hef ol transceivers all in one module This 2S pi es is similar to the 6K6 RJMST It has O LINK 1
77. tially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 5a 6KP6 MT10ST 4 100Mb multi mode FX MTRJ Small Form Factor and 2 10Mb Multi mode ST Fiber port The 6KP6 RJ10ST is a combo module with two different kinds of fiber flavor with two different speeds The top four ports of MTRJ Small form factor fiber support at 100Mb full duplex whereas the bottom two ports multi mode ST Fiber support 10Mb half duplex This combo module provides more flexibility to the user to connect their legacy 10Mb fiber as well as 100Mb to the Magnum 6K16V Switch When installed in a Magnum 6K16V Switch the 100Mb MTRJ connector supports fiber optic cable distances up to the IEEE standard 100Mbps distance limits i e typically 2km at full duplex and 412m at half duplex The 10Mb Multi mode ST Fiber connector supports the standard fiber optic distance limit of 2Km at Full and Half duplex both The functionality of this 1 OOBASE FX multi mode 4 port module is _ 42 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 essentially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 6 6KP8 45MT 4 10 100Mbps RJ 45 and 4 100Mb multi mode FX MTRJ Small Form Factor The Magnum 6KP8 45MT 6KP8 45MT 4 Port 10 100Mbps amp 4 port 100Mbps Multi Mode HO Module is a co
78. to be cascaded X to a 10 100Mb repeater or switching hub in the network The Up link Switch position is configured as position by default from the factory settings on all the RJ 45 ports either used for all copper module or combo module 4 4 Auto negotiation for Fast Ethernet copper ports The Managed Magnum 6K16V Fast Ethernet copper ports can be set for either fixed 100Mb speed or for 10 100 F H N way auto negotiation per the IEEE802 3u standard The selection is made via MNS software The factory default setting is for auto negotiation At 10Mb or 100Mb fixed speed the user may select half or full duplex mode by MNS Software for each RJ 45 port separately For detail information see Section 8 Optimizing Port usage of Magnum 6K16V Software user guide MNS See Section 2 2 9 at page no 13 of this manual to access the 6K16V Software userguide One frequently used application for the Managed Magnum 6K16V Switch copper ports is to connect one of them using a fiber media converter to another Switch in the network backbone or to some other remote 100Mb device In this case it is desirable to operate the fiber link at 100Mb speed and at either half or full duplex mode depending on the capabilities of the remote device Standard commercially available Fast Ethernet media converters mostly do not support auto negotiation properly and require that the switched port to which they are connected be at 100Mb fixed speed Attachment to
79. uilt in stand off female provided at the front of the 6K16V Main Board and screw down tightly with the three 5 16 stand off male on the top of the Granddaughter board The 5 16 stand off has been used to place the daughter board on the top of the granddaughter board and latch it securely t500 IOA resoog0orHd Fig 3 6 2a Granddaughter Board shown separately i es 27 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Fig 3 6 2b Granddaughter Board placed in slot A and secured with three 5 16 stand off s Step 3 The figure here illustrates the basic layout of an individual PM card Each 6KPM card fits into the space provided on the main board Fig 3 6 2c Daughter Board top view of version for 4 copper 10 100 ports Fig 3 6 2d Daughter Board shown upside down with two male latch connectors Step 4 Hold the daughter board with both hands at the end and align the two cream color latching connectors male placed at the bottom of the daughter board with the other female connector placed on the Granddaughter and main board As shown below in Fig 3 5 2e Fig 3 6 2e Magnum 6KPM daughter board aligned with the bottom female connector for the installation 28 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Step 5 Once the latching F connectors are aligned properly and the mounting holes are aligned with stand offs then press slowly and firmly with t
80. utput voltage of the power supply and determine the lead which is more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled The connection procedure is straightforward Simply connect the DC leads to the Switch s power terminals positive and negative screws The use of Ground GND is optional it connects to the Switch chassis Ensure that each lead is securely tightened The 24VDC amp 125VDC terminal block on Magnum 6K16V s is similar to that described in the 48VDC information above 55 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 C5 1 UL Requirements C6 0 C7 0 Pebs mi The following must be adhered to in order to conform to UL requirements Minimum 18 AWG cable for connection to a Centralized DC power source Minimum 14 AWG cable for connection to earthing wiring Use only with Listed 10 A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent Fastening torque of the lugs on the terminal block 9 inch pound max Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rack at least 4 inches apart with the first one located within 6 inches of the terminal block ORDERING INFORMATION To order the optional Dual Source 48VDC power supply factory installed order Dual Src48V as a se
81. ver is connected Consult the dealer or an experienced radio TV technician for help Canadian Emission This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil respecte toutes les exigences du R glement sur le mat riel du Canada Cet appareil est Classe B 11 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 Table Of Contents cennere enine E E ie Page 1 0 SPECIFICATIONS ssssssessissssresscssvisssssososossiesssssssvsaosissssssvosvssosssssos sssss 1 1 1 Technical Specifications ccccccceecceescesscesseeeecesecesecenecseecseeeseeeeeneenes 1 1 2 Ordering Information rsisissecrescrsercsrrneirr esisiini ksero Eesi 4 2 0 Tmtr d cti nsssscserssrsssssisteossssosesooriscessasooesorisdess sso tsor adoste sri sst 6 2 1 Inspecting the Package and Product s sseeeeseeeeeeseeereresrersrrrrerereere 6 2 2 Product Description Magnum 6K16V Managed Fiber Switch 7 2 2 1 Eight port SFF fiber modules 6K8 MTRJ 6K8 MLC eseese 8 2 2 2 Eight Port Copper Module 6K8 RJ45 ossee 9 2 2 3 Six Port 4 2 Combo Modules cccccccecsscecssscecessseeeesseeees 9 2 2 4 Four Port 10 Mb and 100Mb mm Fiber ST Modules 11 2 2 6 Gigabit LOOOMbps port modules ee eeeeceteeeeeeeeseeeeeeeeeees 11 2 2 6 Packet Prioritization 802 1p QOS cecccsecsseessesceereeeeeeseeeesees 12 2 2 7 Frame Buffering and Flow Cont
82. width for high speed to support the peak traffic and minimize congestion IBER Connection 17 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 3 0 Installation Before installing the equipment it is necessary to take the following precautions A f the equipment is mounted in an enclosed or multiple rack assembly the environmental temperature around the equipment must be less than or equal to 50 C Za f the equipment is mounted in an enclosed or multiple rack assembly adequate air flow must be maintained for proper and safe operation Ba f the equipment is mounted in an enclosed or multiple rack system placement of the equipment must not overload or load unevenly the rack system 4 f the equipment is mounted in an enclosed or multiple rack assembly verify the equipment s power requirements to prevent overloading of the building s electrical circuits 5 If the equipment is mounted in an enclosed or multiple rack assembly verify that the equipment has a reliable and uncompromised earthing path This section describes installation of the Magnum 6K16V Switches as well as connection of the various Ethernet media types 3 1 Locating Magnum 6K16V Switches For vertical panel mounting and wall mounting see Section 3 4 For vertical DIN Rail mounting see Section 3 3 For DC power options see Appendix B For Dual Source see Appendix C For AC power input locate an AC receptac
83. wireless telephone service providers Internet Service Providers ISPs and other communication companies In addition many high availability equipment services such as broadcasters publishers newspaper operations brokerage firms and other facilities often use a battery backup system to maintain operations in the event of a power failure It is also frequently used for computer system backup management and operations monitoring equipment The 24V and 125VDC options are particularly useful in the Industrial environment where it is common for facilities to operate on 24VDC or 125VDC power The 125VDC options are mainly used in power utilities such as electrical substations electrical generating plants etc The 24VDC applications are mainly in the Industrial environment such as factory floor HVAC equipment military equipment etc The 5VDC options are mainly used for military or Industrial factory floor applications B4 0 6K16V S 48V 24 125 OR 5VDC INSTALLATION This section describes the proper connection of the 48VDC leads or 24VDC 125VDC SVDC leads to the DC power terminal block on the Magnum 6K16V Switch The DC terminal block on the Magnum 6K16V Managed Switch is located on the left front of the unit and is equipped with three 3 screw down lead posts The power terminals are identified as positive and negative and they are floating inside the unit so that either may be grounded by the user if desired The chassis is
84. wo fingers as shown below in Fig 3 6 2f on the top of the latching connectors until the connectors latched up securely Figure 3 6 2f Securely latching up 6KPM Cards into a Magnum 6K16V NOTE All 6KPM slots need not be filled in order for the Magnum 6K16V unit to be operational When leaving 6KPM slots empty always use a face plate Magnum 6K8 BLNK to cover the slot opening in the front panel This will maintain proper cooling air flow safety and operation as required by FCC CE and other regulations Step 6 Now screw down the daughter board with 6 440 screws so that it holds the daughter board securely The figure below shows the top view of 6KPM card after successfully installing the 6KPM cards inside the Magnum 6K16V Fig 3 6 2g Top View GE as isin 6KPM Module installed inside a a 6K16V Step 7 Once the installation of granddaughter and daughter modules is done the front panel screen plates need to be placed on the front of the chassis cover to complete the installation process for that port module The front panel screen plate comes along with the package of port module separately along with 3 brackets and 6 256 flat head screws The brackets and screws have been www GarrettCom com 29 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 installed inside of the top cover Step 8 Once all 6K PM cards have been installed including faceplates for empty slots the chassis cover sh
85. y option extended temperature rating qualifies the Magnum 6K16V Managed switch for any Industrial factory floors traffic control transportations systems and power utilities applications The bundles of MNS 6K software operated features diversified this managed switch to operate and perform securely and reliably in all critical applications The addition of S Ring and Link Loss Learn software feature allow this Managed switch to provide a very secure highly available redundant network capability in any ring topology network In an Industrial environment where the factory floors are networked with Ethernet based mixed media LANs equipped with PLCs computers for taking reading and data from M C Client Server databases and fetching these important datas to the central office data warehouses The Managed 6K16V s modularity along with MNS 6K features remarkably handle these kind of network very securely and reliably through out the Factory floors The DIN Rail Mounting options on the Magnum 6K 16 allow the Factory floor Industrial s user to mount securely anywhere on their Network setup The option for setting the ports at 10 or 100Mb on copper and supporting the C O 15 Magnum 6K16V Managed Fiber Switch Installation and User Guide 06 04 10 or 100Mb fiber provide a very widespread option to the users to mix match their legacy and advance network needs The modularity of the 6K16V Managed Fiber Switch makes it an attractive choice for use

Download Pdf Manuals

Related Search

Related Contents

JBM electronic Studio Monitors User's Manual  FREQUENTLY ASKED QUESTIONS (FAQ) ON E  異物鉗子  Manual de Instrucciones - Bürkert Contromatic GmbH  BA 10 FAG Motion Guard CONCEPT6 Automatisches Einzel  Samsung MAX-KX75 Инструкция по использованию  PRODUITS POUR CLÔTURE ÉLECTRIFIÉE Manuel de l  Elle Québec : Soleil : mode d`emploi  DRA-F102 - Aerne Menu  mode d`emploi - Au Royaume de l`Amusement  

Copyright © All rights reserved. Failed to retrieve file