Franke Consumer Products LB3200 User's Manual
Contents
1. 3 010 LB2200 Model 10170 LB2200 Model 3 011 LB3200 Model 10171 LB3200 Model End Cap 10166 i 3 012 LB4200 Model 10172 LB4200 Model Lever Kit 3 002 Flow Straightener 10159 B l _Cold Valve amp Seat Set 2 015 a Hot Valve amp Seat Set 2 014 Cover _l Clamp Plate 10115 Backnut 92022 Diagram B Push Fit Connections H 10167 LB2200 Model __ 10168 LB3200 Model 10169 LB4200 Model a i WARNING Do NOT use tools or modify the Push Fit Connections as this could damage the connection resulting in leaks and will vold the warranty opm mo L 10321 lp LA R Connections To Heating Tank U E i 10322 Z Cut to Length for Franke Canister Silicone Tube 10306 Kit 2 023 Where Indicated Specify Color Limited Warranty Congratulations on the purchase of a Franke product Franke is one ofthe world s largest manufacturers of kitchen systems Our products are manufactured using the highest degree of technology quality and design As a result we are proud to offer the following warranty Franke Inc Kitchen Systems Division warrants the quality of its water dispensing systems to be free from manufacturing defects for a period of five years from the date of purchase This warranty app2. Franke Little Butler ORing Seal Inlet Tubes 12 Long Clamp Plate 77 Lock Washer Cold Water Line Backnut Into Heating Tank 1 4 Tee Connector Push Fit ve 3 8 Reducer _ ush Fit Se ee i WY Out Of Heating Tank Shut Off Valve Franke Consumer Products Inc Kitchen Systems Division Connections To Heating Tank Cut to Length for Franke Canister 3050 Campus Drive Suite 500 Hatfield PA19440 USA Phone 1 215 822 6590 Fax 1 215 822 5873 fks filter franke com www frankeksd com FRANKE Franke Little Butler Overview of Installation There are three main components to the system the dispensing head the canister and the heating tank The dispensing head comes with three 1 4 copper tubes and one silicone tube The two shorter 12 copper tubes are connected to the incoming water supply via the canister The supply to the cold side may be diverted through a chiller before the dispensing head if required The longer 18 copper tube is connected to the inlet of the tank The silicone tube is connected to the outlet of the tank using the hose connector Preparing for the Installation As with any sink related device it is much easier to mount the dispensing head of this system onto the sink before the sink is mou
3. SS FORA PARTICULAR PURPOSE This warranty gives you specific legal rights which may vary from state to state What you must do The purchaser should retain original proof of purchase Failure to do so may void this warranty
4. hooting Should your dispenser not work correctly check the list below before calling for service The following things are not covered by the warranty WARNING Do not operate both levers at the same time as this can build up pressure in the heating tank causing the bladder to expand and eventually burst Such damage is not covered by the warranty Water is not hot Check if electrical supply to heating tank is plugged in Turn temperature control knob clockwise as far as possible Test the temperature again after 15 minutes Check if fuse is blown or circuit breaker is open Hot water continuously drips or sputters from spout For safety reasons this faucet may drip or splutter after use This venting prevents a build up of pressure in the heating tank If this becomes excessive Turn the control knob counter clockwise to lower temperature Check the tubes connecting the faucet to the storage tank are not kinked Check the condition of the canister and clean or replace if necessary Water does not flow Check the shut off valve is open Check if supply tube is kinked Franke Little Butler Spare Part S For out of warranty maintenance and repairs we recommend you employ a Registered Plumber Before ordering spare parts determine the correct reference number from the exploded diagram Quote this number and where appropriate the color of your faucet WARNING Do NOT Use Tools N Spout amp Shank Lever End
5. lies only to the original owner providing the product has been installed in accordance with our installation instructions used as recommended and ina normal residential application In the event of a warranty claim the owner will be required to provide proof of purchase This warranty covers all components necessary to restore the product to good working condition Franke reserves the right to inspect the installation prior to the replacement of the product or component part This warranty does nat cover misuse or abuse accidental damage scuffs or scratches abnormal usage negligence or damage caused by improper maintenance or cleaning Normal wear of parts is excluded from warranty Damage caused by impurities or acts beyond our contrd are not covered Any product or part which has been repaired or altered in any manner outside of Franke s factory unless previously authorized in writing by Franke will void warranty Any replacement excludes transportation and any labor reinstallation costs This warranty does not allow recovery of incidental or consequential damages such as loss of use delay property damage or other consequential damage and Franke accepts no liability for such damages The Frarke warranty is limited to the above condition and to the warranty period specified herein and is exclusive Franke DISCLAIMS all other warranties expressed or implied including the IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNE
6. nted into the countertop A mounting hole of 1 3 8 diameter standard sink ledge drilling is required Itis always recommended to take the components and locate their optimum positions before starting the installation IMPORTANT Do not plug in the unit until all water connections have been made and the tank is filled completely Making the Supply Provision Provide a branch compression connection for a 3 8 supply tube This should be done with a conventional tee and the shut off valve provided Flush the pipework before installing Mounting the Dispensing Head The copper tubes are coiled for packing and must be carefully straightened before installation Feed the tubes and shank through the hole in the sink ledge or counter Assemble the clamp plate locking washer and backnut hexagon to the top for thin sinks fingertight Tum the dispensing head and the spout until the handles and spout are in the required position for use and fully tighten the backnut this will lock the spoutin position Seasonal Shutdown If you plan to be away from home for extended periods the following procedure must be carried out 1 Operate the hot lever until the water runs cold 2 Shutoff the main water supply A stop valve was supplied with the system for this purpose and will be found located on the adjacent pipe work 3 Operate both levers to confirm that the water supply is turned off and to release the pressure in the system Troubles
Download Pdf Manuals
Related Search