Extron electronic Extron Electronics Switch DTP T USW 233 User's Manual
Contents
1. 3Extron Electronics INTERFACING SWITCHING AND CONTROL DTP T USW 233 e Setup Guide This guide provides instructions for an experienced installer to set up and operate the Extron DTP T USW 233 switching video transmitter The DTP T USW 233 transmitter switches among an analog video and two digital HDMI video inputs and paired with a compatible receiver can extend the selected signal up to 230 feet 70 m If the selected input is HDMI the extended video signal is HDCP compliant OVER DTP REMOTE RS 232 _IR Tx Rx G Tx Rx Installation Step 1 Mounting Turn off or disconnect all equipment power sources and mount the transmitter as required Step 2 Making Connections Inputs Input 1 RGB connector Connect a VGA cable between this port and the VGA output port of the analog video source Input 2 and 3 HDMI connectors Connect HDMI cables between these ports and the HDMI output ports of the digital video sources NOTE See the Locklt Lacing Brackets on page 3 of this guide for to securely fasten the HDMI connectors to the transmitter 3 Audio input Connect an unbalanced stereo audio source to this 3 5 mm mini stereo jack for an analog audio input NOTE Audio is not embedded in the HDMI signal it is transmitted simultaneously and is present on all inputs IR Device Over DTP RS 232 and IR pass through COM CSSS RS 232 and IR connector To pass serial or infrared2. data or control signals on the Over DTP RJ 45 output connect the controlling device to the transmitter via the RS 232 and IR captive screw connector Connect the device to be controlled to the receiver OVER DTP DTP output to receiver DTP RJ 45 connector Connect the transmitter DTP Out port to the DTP In port on the receiver Extron recommends that you terminate both cable ends in accordance with the Pins TIAEIAT following specifications at a minimum 568B TIVEIAT 568B e CAT 6a shielded e 24 AWG solid conductor 5 White blue TP Wires 8 Do not connect this device to a computer data or telecommunications network Signal LED Lights when the unit is outputting a TMDS clock signal on the DTP output Link LED Lights when a valid link is established between the units on the DTP cable Remote control Remote Contact port If desired for contact closure control plug a locally contructed contact closure control device into this 3 5 mm 4 pole captive screw port Momentarily short the pin for the desired input 1 2 or 3 to G to select that input To force an input to be always selected leave the short in place NOTES e Contact closure control overrides front panel input selections e For contact closure control auto input switching mode must be off see Selecting the switch mode on the next page DTP T USW 233 Setup Guide Continued Remote Tally port If desired to
3. NORMAL AUTO All three LEDs flash three times Release the Input buttons The switcher has a front panel lock feature that locks the front panel If you try to make front panel input selections when the panel is locked all front panel LEDs flash three times Toggle the front panel lock on and off by pushing and holding all three Input buttons simultaneously for 5 seconds All front panel LEDs flash three times Release the buttons Interpreting the Status LEDs Signal LEDs 1 through 3 Indicate that the switcher detects horizontal sync STATUS Signal LED 1 or TMDS clock Signal LED 2 and Signal LED 3 signals on the associated input E 1 2 3 _o HDCP LEDs 2 and 3 Indicate that the corresponding input signal is HDCP encrypted aner Lockit Lacing Brackets Use the included Locklt Lacing Brackets to securely fasten both HDMI cables as follows 1 Plug the HDMI cable into the panel connection 2 Loosen the HDMI connection mounting screw from the panel enough to allow the Locklt lacing bracket to be placed over it The screw does not have to be removed 3 Place the Locklt lacing bracket on the screw and against the HDMI connector then tighten the screw to secure the bracket 4 Loosely place the included tie wrap around the HDMI connector and the Locklit lacing bracket as shown 5 While holding the connector securely against the lacing bracket use pliers or similar tools to tighten the
4. connected to either unit in the pair powers both units A power supply is included with the SECTION A A transmitter Power Supply A Output Cord A Front panel Configuration port G Configuration port Plug a PC or other controlling device into the switching transmitter via this front panel mini USB connector for remote configuration of the switching transmitter AUTO SWITCH Operation Extron Switching inputs Select the desired input by pressing the associated input button Observe that the LED for the selected input lights Press the button The LED lights green NOTE The switcher must be in normal manual mode see below 1 2 3 Selecting the switch mode OD m m i MODE NORMAL AUTO In auto input switching mode the switcher selects to the highest numbered input with a sync signal present Turn auto input switching mode on and off as follows 1 Press and hold the Mode Input 1 button 2 Press and release the button for the desired mode Precs theand HOLD ihe Node buton Auto Input 3 The Auto Switch LED lights Press and release the Auto or Normal button Normal Input 2 The Auto Switch LED goes off f 4 Auto Switch lights auto or goes out normal 3 Release the Mode button l 3 ance ee rere gt Locking and unlocking the front panel MODE NORMAL AUTO Release the Mode button Executive mode Press the and HOLD the all three Input buttons oR MODE
5. remotely identify the currently selected input plug a locally constructed device into this 3 5 mm 4 pole captive screw connector Connect the power wire for the device into the V pin and connect the ground wire for the each indicator into the corresponding tally output pin 1 2 or 3 When an input is selected by either contact closure or front panel selection the corresponding tally output pin shorts to ground closing the circuit and lighting the connected indicator LED l 5 e mm MAX SSs 9 x4 XL cec sH aowa Remote RS 232 port Plug a serial RS 232 device into the switching transmitter via this rear panel 3 5 mm 3 pole captive screw connector for remote control of the switching transmitter Reset button Reset button This button initiates two levels of reset For different reset levels use an RS 232 Device Extron Tweeker or small screwdriver to press and hold the recessed button while the switcher is running or while applying power See the DTP T USW 233 User Guide available at www extron com for details Power Power connector Connect an IEC power cord between the included 12 VDC mi Ridges power supply and a 100 240 VAC 50 60 Hz source Connect the power supply to either unit transmitter or receiver as shown at right Use the included tie wrap to OGY Captive Screw Connector strap the cord to the captive screw connector NOTE Only one power supply is required A single power supply
6. tie wrap then remove any excess length Application Diagram Extron Extron TouchLink DTP T USW 233 Peay Contro DTP Transmitter Pee System TCP IP SF z Switcher SS eon T Extron M IPL 250 _ AV Device A RC ontro l 4 J CATx Cable Up to 230 70 m Document Camera S Laptop Figure 1 Typical Switching Transmitter Application lt Extron L DTP HDMI 230 D Rx Receiver Ni AV Device Sp Control 0 HDMI with Embedded Audio Flat Panel Display with Speakers Extron Headquarters Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Extron Korea Extron India 800 633 9876 Inside USA Canada Only 800 3987 6673 65 6383 4400 81 3 3511 7655 86 21 3760 1568 971 4 299 1800 82 2 3444 1571 1800 3070 3777 Inside Europe Only 65 6383 4664 FAX 81 3 3511 7656 FAX 86 21 3760 1566 FAX 971 4 299 1880 FAX 82 2 3444 1575 FAX Inside India Only Extron USA West Extron USA East 1 714 491 1500 1 919 850 1000 31 33 453 4040 91 80 3055 3777 1 714 491 1517 FAX 1 919 850 1001 FAX 431 33 453 4050 FAX 91 80 3055 3737 FAX 68 2490 50 Rev A A 2013 Extron Electronics All rights reserved All trademarks mentioned are the property of their respective owners www extron com 1113
Download Pdf Manuals
Related Search