Extron electronic Extron Electronics Speaker SM 3 User's Manual
Contents
1. location of two pilot holes using the holes on either side of the mounting plate so that the stud does not interfere with the speaker wire routing as shown below NOTE A speaker wire access hole see the figures below must also be cut in the wall so mark that hole location now with the mounting plate positioned on the wall while ensuring that the wall stud does not interfere with the wire routing and that the mounting plate hides the access hole f 0 Mounting Plate 10 Mounting Plate Alternate Access Point Alternate Access Points NOTE When mounting to surfaces that do not allow wires to be routed from behind Such as on masonry or concrete walls and the wires are routed to the speakers via a raceway use the alternate access 7 Mounting Screws points to run the wires to the quick connect speaker contacts see the figures above ATTENTION Use the appropriate mounting screws see the above ATTENTION Drill the mounting plate pilot holes and cut the speaker wire access hole as previously marked Route the speaker cable through the rear of the mounting plate and attach the wire ends to the quick connect contacts using a small screwdriver see the illustrations at the top of this page Besure to observe the correct polarity 5 Attach the mounting plate to the wall Attaching the Speaker to th2. 21 3760 1566 FAX All rights reserved WWw extron com Secondary Support Cable Extron Korea 82 2 3444 1571 82 2 3444 1575 FAX Extron India 1800 3070 3777 Inside India Only 91 80 3055 3777 91 80 3055 3737 FAX 68 1540 50 Rev B 04 13
3. FG Maea wm Extron Electronics INTERFACING SWITCHING AND CONTROL x 9 be vrio SM 3 Setup Guide This setup guide contains installation information about the Extron SM 3 speaker Installing the Speaker Mounting Plate The SM 3 speaker comes with two types of speaker mounting plates 0 mounting plate The 0 plate allows the speaker to be mounted flat on a vertical wall with the speaker protruding less than four inches ADA compliant from the wall surface 10 mounting plate The 10 mounting plate allows the speaker to be MALCE at a 10 degree angle so that the speaker can be pointed down from an elevated position The mounting plate can be installed vertically or horizontally as shown on the right J A ys iS af iy A a i S Q A Y Voz Z Z Daw LD yr Fi 0 Mounting Plate 10 Mounting Plate Vertical Mounting Horizontal Mounting NOTE Observe all applicable building codes and local ordinances when installing the speaker Mounting to a Wall Box 1 Route the speaker cable through the rear of the mounting plate and attach the wire ends to the quick connect contacts using a small screwdriver see the following figures on the next page Be sure to observe the correct polarity NOTE The positive connector and the negative connector are marked on the mounting
4. e Mounting Plate ATTENTION to the mounting plate be sure that the speaker is unlocked Failure to place the speaker in the unlocked position will result in damage to the speaker lock mechanism should an attempt be made to mount a locked speaker see Using the Security Key to Lock and Unlock the Speaker below NOTE If a secondary attachment point is being used see the Attaching a Secondary Support Cable section on the next page for installation details before proceeding further Position the rear mounting slot of the speaker above the catch tab of the mounting plate then slide the speaker down into the mounting plate so that the speaker is secured in place see figure on the right When properly seated the speaker connections are automatically made Using the Security Key to Lock and Unlock the Speaker Insert the key into the center of the speaker grill and turn the key as needed so that the speaker is in the unlocked position See the figure below There are three small raised dimples on the grill surface that surrounds the keyhole Repeat this procedure but set the key to the locked position to lock the speaker Removing the Speaker from the Mounting Plate To remove the speaker from the mounting plate you must unlatch the locking mechanism 1 Insert the security key into the keyhole of the speaker grill see the previous section and turn the key to the unlock position 2 Remove t
5. he security key 3 Apply pressure with your finger over the keyhole to unlatch the speaker from the mounting plate while lifting up on the speaker see figure on the right ATTENTION To avoid damaging or scratching the grill finish do not use tools or sharp instruments to depress the unlocking mechanism hidden behind the center of the grill By default the SM 3 speaker is shipped unlocked When mounting the speaker Catch Tab Unlocked Press to Release Attaching a Secondary Support Cable If a secondary support cable is being attached use the included screw to attach a suitable cable to the screw hole as shown below Insert screw here Reference only Extron Headquarters 800 633 9876 Inside USA Canada Only Extron USA East 1 919 850 1000 1 919 850 1001 FAX Extron USA West 1 714 491 1500 1 714 491 1517 FAX Extron Asia 800 7339 8766 Inside Asia Only Extron Europe 800 3987 6673 Inside Europe Only 65 6383 4400 65 6383 4664 FAX 31 33 453 4040 31 33 453 4050 FAX 2013 Extron Electronics Anchor this end to a suitable secure point Attach cable here and secure Extron Middle East Extron China 4000 EXTRON Extron Japan 4000 398766 Inside China Only 81 3 3511 7655 81 3 3511 7656 FAX 971 4 2991800 971 4 2991880 FAX 86 21 3760 1568 86
6. plate 2 Attach the mounting plate to the wall box using two mounting screws see figure below NOTE The mounting screw holes in the mounting plate allow for some degree of play and lateral movement so that the mounting screws may S i n be aligned properly with the screw holes of the PE pe S_ Top Screw wall box Observe U S and European screw locations as shown on the right lly ia ATTENTION Make sure that the wall box is am C secured to the wall structure and can handle the weight of the speaker If there is doubt secure e A A O the mounting plate with additional mounting screws The wall stud mounting holes can be used for this purpose European Box Screw Location U S Box Screw Location SM 3 Setup Guide Continued ATTENTION Use the appropriate mounting screws The screw heads must not protrude more than 074 1 9 mm above the screw holes in the mounting plate See the figure below left If the screw head protrudes too far above the mounting plate surface damage to the speaker may occur when the speaker is attached see the figure below right Mounting Screws 5 mm Mounting to a Wall Stud 1 Install the speaker cables into the wall or conduit before installing the speaker mounting plate Leave enough slack 2 Locate the wall stud where the mounting plate will be installed and while positioning the mounting plate on the wall mark the
Download Pdf Manuals
Related Search