Extron electronic Extron Electronics Projector Accessories PMK 550 User's Manual
Contents
1. switcher and pull any excess cable back into the ceiling Feed the output cables to the the cable access slot to the base of the pipe 9 Continue installing the projector and other devices following the manufacturers directions projector via 10 Slide the covers onto the base plate passing the AC power cord out through the slot between the covers see figure 3 11 Lock the covers to the plate with the cover screws Refer to the relevant PoleVault System Installation Guide to complete the installation and setup Power Cord Slot Pipe Collar Screw 10 32 Set Screws 4 to attach PMK toa projector pole Power Supply PVS 305SA IP Switcher Cable Access Slot Cable Slot Cover Projector Pole CO Figure 3 Attach the PMK to the pole cable the PVS switcher PVS 305SA IP shown and then re attach the two covers Extron Headquarters Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Extron Korea 800 633 9876 Inside USA Canada Only 800 3987 6673 65 6383 4400 81 3 3511 7655 86 21 3760 1568 971 4 299 1800 82 2 3444 1571 Inside Europe Only 65 6383 4664 FAX 81 3 3511 7656 FAX 86 21 3760 1566 FAX 971 4 299 1880 FAX 82 2 3444 1575 FAX Extron USA West Extron USA East 1 714 491 1500 1 919 850 1000 31 33 453 4040 1 714 491 1517 FAX 1 919 850 1001 FAX 31 33 453 4050 FAX 2013 Extron Electronics All rights reserved All trademarks mentioned are the property of their resp2. Pi of Ase FY 3 Ja N 3 3 a ae urio PMK 550 e Installation Guide Extron Electronics INTERFACING SWITCHING AND CONTROL The Extron PMK 550 Pole Mount Kit designed for use with the Extron PoleVault System allows for easy mounting of PoleVault products to a projector pole The PMK 550 is compatible with both the PVS 204 series and PVS 305 series of PoleVault switchers When installed it mounts the PoleVault system switcher the associated power supply and an accessory device within an enclosure below a suspended ceiling Items included in the kit are Installation To install the PMK 550 in a PoleVault system 1 4 CAUTION Maximum load for the PMK 550 is 15 Ibs 6 8 kg Covers 2 Base plate 1 Mounting plate 1 Tie wraps and pads to secure power supply 4 40 Screws to mount devices 3 Cover Screws 4 NOTE For full device installation configuration menus connector wiring and operation details of the PoleVault switcher see the relevant PoleVault System Installation Guide available at www extron com a 2 To open remove 4 cover screws and slide the covers away Mounting Plate 1 Remove the four cover screws from the center see figure 1 Slide the two halves apart and remove them from the base plate NOTE If the PoleVault switcher and its power supply are already installed go directly to step 5 To mount the PoleVault switcher place th
3. e mounting plate with the raised tabs upwards on top of the switcher top and pass the two supplied 4 40 x 3 16 inch screws into the top of the switcher see figure 2 top Secure the mounting plate but do not overtighten Hook the combined plate and switcher into the PMK 550 base plate Secure it to the base plate with two screws NOTES e Any installed switcher should be secured to the plate in an upside down position so that when the plate is rotated to hang from the ceiling the device will be in its correct orientation See figure 2 bottom Use only supplied screws to avoid damaging the switcher Attach the associated power supply with the supplied tie wraps and pads by passing them through the appropriate slots and around the power supply see figures 2 and 3 Tighten until snug Figure 2 Installing the PVS Switcher PMK 550 e Installation Guide Continued 5 Loosen the four pipe collar set screws and slide the plate up the pipe until the base plate is touching the suspended ceiling 6 Level the plate and secure it by fully tightening the set screws NOTE At least three set screws must come in contact with the pipe 7 Route the signal cables so that they exit the pipe via the cable access slot See figure 3 WARNING Do not thread any high voltage power cabling such as power supply or projector power cords through the projector pipe This violates National Electrical Code 8 Attach the cables to the
4. ective owners www extron com Extron India 1800 3070 3777 Inside India Only 91 80 3055 3777 91 80 3055 3737 FAX 68 1502 01 Rev B 08 13
Download Pdf Manuals
Related Search