Home
Epson R2400 User's Manual
Contents
1. of air space is more than 20cm please clean the printer head for 2 or 3 times before printing 2 Printer testing 1 Check whether the printer is in normal condition like mechanical status lubrication status etc 2 Print testing lines to ensure the printing head is good condition 3 Print pictures to see whether the printing image is ok 3 Installation Procedures 1 First step i ins E Put the CISS on the left side Pull out the small rubber plug Place 8pcs of air filters into of the printer In the meantime from the air hole as above air holes the thicker side place all the tubes at correct picture shown is down into tank position 2 Second step Remove out the original cartridges Press the ink cartridge replace button to make the small cart move to the position which ready to change the ink cartridges And draw out the electrical Source 3 Take off the cartridge cover And screw the screwdriver in clockwise till the right side of the cover divide from the connection on the cart then take down the cartridge cover 4 The fourth step Place the Cartridges in PLA PE f a DE Pen i Be i m ur E x A z Remove out the original cartridges then place down each cartridge according to the color in the meantime make every cartridge in the correct position er i A a pi A i T pa P Remove the cartridge cart back and place the cartridge
2. CIS for Epson Stylus Photo R2400 Thank you for purchasing ST Continuous Ink Supply System We appreciate your support and will try our best to make your experience with our products a pleasant one Printing has been a different experience ever since you installed ST Continuous Ink Supply system on your own printer Just imagining being able to print without regard to the ink level in those expensive little cartridges Please take your time installing ST Continuous Ink Supply system Do not remove your old cartridge until you have the ST CIS system primed and ready to install to prevent the drying of heads In addition make sure you are getting perfect nozzle checks before installing the ST CIS system The ST CIS system won t be able to work properly if the nozzles are previously clogged Most people get a perfect nozzle check the first time after installing the ST Continuous Ink Supply system others may need to run two or three cleaning cycles or let the printer sit for a while before they get the perfect results 1 General Guide 1 Components A CIS system 1 set B Air filters 8pcs C SupportArm 1 set D Refill Kit 8pcs E Instruction CD 1pc 2 Opening box inspection a Check whether all the accessories are ready b Check whether there s leakage of CIS System whether some tubes have been separated from CISS If there is please kindly to contact the local dealer C Check whether there is air space in the tube If the length
3. ntout Head Cleaning H Use this utility if your print quality declines or the Nozzle Check indicates clogged nozzles Print Head Alignment F Use this utility if misaligned vertical lines appear in your Ba If it show this brea ks J Frinter and Sale Information please clean S Use this utility to E or ven Sines a7 POU Ber and the pri nting head optional devices Speed amp Progress Version 5 50 Enter this item If there show breaks please clean your printing head It is possible that the wispy air have entered into the printing head If it is still show little breaks specially show in one color it no need to repeatedly continue to clean Just keep the printer silent for about one hour it may disappear If after testing it still abnormal please kindly to contact with local dealer 4 Reset Procedure El ieri 73 1 Fago Mid Faerie IR mua he at ja aa zur y Tip Ls a Bata pe Flan apur A Topa Fleie da si a i W Fear fore Hj Ale t pa TE ona Error Frame Tipr fav ela Eb dE ds ali Jakarta ir ros tal pee ae rid me Detui c silar pois bin ar Alles TT E e E If the indicator light show flashing when printing it tell you that you need to change the cartridges the please power off the printer for about 1 minutes and turn on again this time it will show full on the computer then it can work in good condition 5 Refill Ink Please pay attention to the ink level in the reservoirs if
4. s down as show in picture then click the cartridges to the right position 5 The fifth step Z Fix up the support arm aa add fe Rip the label Stick the Support arm at 25cm Rip the label distance from the side of the printer onthe balance arm Fix the balance arm stick on the support arm as show on the picture Rip the label on the shortest arm And Stick it on the right side of the printer but need to keep it in the same horizontal line as show in the picture 6 The sixth step Installing tubes Clip the tubes in the clip 7 Adjust the tubes Adjust the tube length and move the cartridge car Insure there will no block and collision when the tubes moving with cartridge car Insure there s plenty length of tube to make the cartridge cart can thoroughly move to the left side The tube is excessive long it The tube is twist itis notok In this situation it is ok is not ok 8 The eighth step Insert the electrical source Power on the printer to check line suitably whether the printer works well 9 The ninth step Checking the printing head we Maintenance Status Monitor 3 IM III Il Mit IN Ii AN HL N tl Mi nT DR ifi Use this utility to automatically TE ie errors E ee the level of ink remaining Nozzle Check M Everything is in normal You can work your print Use this utility if gaps or Faint areas appear in your pri
5. tems reversed or leaning during the shipment Please make sure all the ink filling holes and Ventilation holes are closed tightly during the transportation Otherwise the ink shall leak out 6 Don t sway the cartridge frequently It may cause ink leakage 7 Don t pull out the connector of cartridge and don t tear off adhesive tape at the bottom of cartridge 9 Warning 1 Not drinkable keep it out reach of children 2 Avoid exposure to direct sunshine and don t keep it in high or freezing temperature 3 Avoid collision and fallen down
6. the ink level is below 1CM as the above picture shown please use refill kits to fill ink into Reservoir bottles Carefully pull out the rubber plugs from the refill holes there is possibility of ink spattering Be careful Refill ink according to the color in short supply Then put the rubber back Please keep the printer and the reservoir at the same horizontal line during the process of refilling ink 6 Assemble the cartridge cover First place the left side of cartridge cover down correctly second put the other side of the cartridge cover atthe above of the cart and adjust the position of the connection Then press the right side of the cartridge cover to make it down to the suitable position now it is ok to work 7 Attention for maintenance Take out the CISS including the inner cartridges and other components Then remove support arm from printer and place the original cartridges in Please inquire local dealer before sending to maintenance 8 Notice 1 Please don t take out cartridge at random after installing the CIS system Keep the reservoir bottles on the same level with the printer 2 Try to keep at least 1 2 inch of ink in the bottles as you don t want to run out of ink and draw air into the cartridge 3 Don t place the Reservoir Bottles higher or lower much than the printer 4 To be used in a dry place between 15 and 35 degree Avoid exposure to direct sunlight 5 Don t put the continuous ink supply sys
Download Pdf Manuals
Related Search
Related Contents
取扱説明書 4 Mode d`emploi Juniper NetScreen-500 System 3 dual-10/100 modules, 2 DC power supplies BMW M6 Convertible Service and Warranty Information AOC 2436V Owner's Manual Clarisonic Mia User Guide document - Le plaisir d`apprendre 取扱説明書(PDF/205KB) Samsung ST700 Manual de Usuario User Manual Copyright © All rights reserved.
Failed to retrieve file