Emerson EWL3706 Owner's Manual
Contents
1. ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 21 GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H NEC NATIONAL ELECTRICAL CODE S2898A 14 LIGHTNING For added protection for this TV receiver during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the TV due to lightning and power line surges 15 POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light of power circuits or where it can fall into such power lines or circuits When installing an out side antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 16 OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock 17 OBJECT AND LIQUID ENTRY Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liq uid of any kind on the TV 18 SERVICING Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous voltage or other haz ards Refer all servicing to2. 11 EN INITIAL SETTINGS INITIAL SETUP 3 When you first turn on your TV the following This section will guide you through your TV s initial screen is displayed Use A W to select the set up which includes selecting a language for your on screen menu language from the choices on on screen menu and AUTOSCAN which automati the right side of the screen cally scans and memorizes viewable channels Initial Setup Select the language for setup display English Elija idioma de preparaci n Espa ol S lectionner langue cran config Fran ais The Antenna Confirmation menu on step 4 will be displayed in the selected language after you press ENTER 4 Select source of ANT IN jack using A V then press ENTER Minitial Setup 1 After making all the necessary connections turn Male sure tne antenna connected to ANT We Air elect the destination of ANT IN jack Cable on your TV 2 Press POWER Initial Setup menu will appear e This operation may take a few moments e f Initial Setup menu does not appear press and hold ENTER for 3 seconds initial setup will appear then proceed to step 3 If initial set up has already been completed refer to MUTET LANGUAGE SELECTION on page 17 Now the system is scanning for channel please watt Analog channels Digital channels e When scanning has completed the lowest memorized channel will be displayed NOTES e The initial Autosca
3. 11 GROUNDING OR POLARIZATION This TV is equipped with a polar ized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your elec trician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 12 POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appli ance 13 OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the TV be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA No 70 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode Fig A FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER ANTENNA 2 EAD IN NATIONAL ELECTRICAL CODE ra GROUND CLAMP
4. 18 30 i CH4 1 CH4 2 CH4 3 CH4 19 00 a GH4 1 bel CH4 3 19 30 V CH4 1 CH4 2 20 00 gt change automatically gt change manually by pressing CH A Y on your remote control NOTE e No Signal will appear on the screen after the minor channel broadcast is over You will need to change the channel to continue watching another TV program VOLUME ADJUSTMENT This section describes how to adjust the volume The mute function which turns the sound off and on will also be described A MEME MUTE VOL A V Use VOL A V to adjust the audio volume e The same operation is available with VOLUME A V on the top panel of the main unit e The volume bar will be displayed at the bottom of the screen when adjusting the volume Kj Volume 20 TESIS e The volume bar display will automatically dis appear in a few seconds MUTE e Press MUTE to turn off and on the sound e Mute is displayed on the screen for a few sec onds e Press MUTE again or VOL A V VOLUME ANN to release the Mute status STILL MODE You can freeze the image shown on the screen STILL 1 Pause the image e When you press STILL the image shown on the screen is paused e The audio is not paused and keeps on reading out e f the digital signal is gone or protected the image will remain paused and the audio will be muted e The Still function will be released afte
5. es 4 FEATURES 4 FUNCTIONS su 38 1o eh aes ee d OE ee EXE ee es de is RC S b a 6 REMOTE CONTROL TOP AND REAR PANEL FUNCTION s 6 INSTALLING THE BATTERIES a 7 BATTERY PRECAUTIONS s s 7 PREPARATION FOR USE 0 0 0 0 o 8 CONNECTION eee as 8 ANTENNA CABLE CONNECTION ss 8 CONNECTION TO CABLE SATELLITE BOX nana a a 8 CONNECTING OTHER DEVICES ras 9 HOME e T 9 COMPONENT CABLE CONNECTION sr 10 S VIDEO CABLE CONNECTION rss 10 VIDEO CONNECTION asa icd ecos caw tracce SOEUR hon ROME a ae he BREAD EG OSD Dae RR RT de ond d 11 DIGITAL AUDIO CONNECTION ss 11 ANALOG AUDIO CONNECTION s 11 INITIAL SETTINGS amp 5 31 xci de an le qoa a RE e a o ha es IB re 00 8 m 12 In SETI ee oe ow en te acts hens et ee a Gea died a 12 CHANNEL SETTINGS 000 ce eee ees 13 AUTOSCAN cursa ratos weoaes hee hoe was RT EGRE PE EGG RE EUR Rd evened e RE enon 13 CHANNEL LIST uiua oe ir Dr CR dc o ed oe Le inp CRGO ee ew 14 MANUAL REGISTER eas 15 ANTENNA CONFIRMATION sse 16 LANGUAGE SELECTION sss 17 WATCHING TY Arr 18 CHANNEL SELECTION 2 a bee kee oe Die ALAS d 18 VOLUME ADJUSTMENT sic cua ae 3 2 aoe Sentra acte Ca Mave eek Sane wk ORR a Weak Ak hoe oe ae dawn 18 STEEL MODE cuuiwae cee aries ei ben
6. 10 EN VIDEO CONNECTION Offers standard picture quality for video devices connected to your TV When the audio jack of the video device is monaural connect the audio cable to the audio L input jack To VIDEO1 input jack EX IDEO ar Video cable not included To video output jack AUDIO VIDEO OUT OUT R L To audio output jacks Camcorder Video Game Iso EMEN VCR S VIDEO1 S VIDEO2 O To AUDIO Rear of this TV Audio cable not included input jacks DIGITAL AUDIO CONNECTION If you connect this TV to an external digital audio device you can enjoy multi channel audio like 5 1ch digital broadcasting sound Required digital audio coaxial cable not included Digital audio coaxial cable not included To DIGITAL AUDIO OUT jack COAXIAL ANT IN i AUDIO OUT AUDIO To coaxial digital DIGITAL OOO HDMI IN ur QOO EH audio input jack Rear of this TV Dolby Digital decoder Manufactured under license from Dolby Laboratories Dolby and the double D symbol are trademarks of Dolby Laboratories ANALOG AUDIO CONNECTION If you connect this TV to an external analog audio device you can enjoy stereophonic 2 channel audio sound Required audio cable not included To audio input jacks o Stereo syste To AUDIO Rear of this TV OUT jacks Audio cable not included PREPARATION FOR USE
7. Background opacity of the displayed caption can be switched as below CC Style Closed Caption 2 EXIT User Setting Font Style O El E Font Size Font Color ffi CHanneL Font Opacity Im DETAIL Back Color Solid Back Opacity Flash LANGUAGE Edge Color Translucent Edge Type Transparent Edge Color Edge color of the displayed caption can be switched as below CC Style Closed Caption gt EXIT User Setting Font Style White ra ILE Font Size Black Font Color SSj AS i Ped Font Opacity Green D DETAIL Back Color Blue Back Opacity Yellow Edge Color Magenta Edge Type Cyan Edge Type Edge type of the displayed caption can be switched as below Closed Caption User Setting Font Style Font Size Font Color None Font Opacity Raised Back Color Depressed Back Opacity Uniform Edge Color L Shadow Edge Type R Shadow 7 To exit the setup press SETUP OPTIONAL SETTINGS 27 EN V CHIP 3 Enter the password You can block certain programming inappropriate for Use the Number buttons and enter the children This block can be released by entering a 4 digit number password 1 Display the setup screen e Press SETUP The following setup screen appears 2 Select DETAIL and press ENTER Using A Y select V chip Detail 2 EXIT Closed Caption vechip SY Picture went HDMI Audio Auto l CHANNEL D DE
8. CC1 and Text are the primary caption and text services The captioning or text is displayed in the same language as the program s dialogue up to 4 lines of script on the screen where it does not obstruct relevant parts of the picture CC3 and Text3 serve as the preferred data channels The captioning or text is often a secondary lan guage translation simplified English or displayed at a slower rate CC2 CC4 Text2 and Text4 are rarely available and broadcasters use them only in special conditions such as when CC1 and CC3 are not available or Text1 and Text3 are not available programs Paint on mode Displays input characters on the screen immediately Once characters are stored in memory they are displayed all at once Roll up mode Displays the characters continu ously by scrolling max 4 lines Pop on mode To exit the setup press SETUP NOTES e Closed captions must be broadcast or included in your recorded content to appear on your TV e Closed captions will not be displayed when you are using an HDMI connection e If the closed caption is not broadcasted nothing is dis played e The closed caption is not displayed when you use HDMI connection e When your TV receives a special effects playback signal i e Search Slow and Still from a VCR s video output channel CH3 or CH4 the TV may not display the correct caption or text e Captions and texts may not match the TV voic
9. 1 5A Channel frequency synthesized tuning system Direct access keyboard Programmable scan and Up down VHF UHF CATV 75 ohm unbalanced F type Mini DIN 4 pin jack x 2 RCA jack x 2 RCA jack L R x 4 Component Video Audio Input One pin jack Y 1Vpp x 2 Two pin jacks Pb Pr 700mVpp x 4 RCA jack L R x 4 HDMI Audio Input HDMI jack RCA jack L R x 2 Coaxial Digital Audio Output One pin jack 500mVpp Analog Audio Output RCA jack L R x 2 Stereo Sound System Speaker ELECTRICAL SPECIFICATION Sound Output 5W 8 ohm x 2 OTHER SPECIFICATIONS Remote Control Operating Temperature Power Requirements Power Consumption Maximum LCD Dimensions Weight Digital encoded infrared light system 5 C to 40 C 41 F to 104 F AC120V 60Hz 205W 37 wide XGA panel 1 366 x 768 pixels lt Without stand gt H 26 9 16 674mm W 37 5 16 948mm D 4 12 16 120mm lt With stand gt H 28 5 16 718 5mm W 37 5 16 948mm D 12 13 16 325mm 52 8 lbs 24 0kg e Designs and specifications are subject to change without notice and without our legal obligation e f there is a discrepancy between languages the default language will be English MISCELLANEOUS SPECIFICATIONS 35 EN Emerson LIMITED WARRANTY FUNAI CORP will repair this product free of charge in the USA in the event of defect in materials or workmanship as follows DURATION PARTS FU
10. E and 2 indicate the 2 e position of the screw Stand holes on this TV 1 Turn this TV over and place it screen first onto a NOTES o table which has a soft cloth draped over it e Only use the screw holes indicated by 2 for Place this TV in a way so that the stand hangs mounting this TV over the edge of the table e For instructions on how to attach the TV rails refer to the instruction manual included with the wall NOTES mount Kit e Make sure to use a table which can support the OPTIONAL SETTINGS MISCELLANEOUS weight of this TV and is larger than this TV e Make sure the table is in a stable location 4 Attach this TV to the wall NOTE 2 Remove the stands from this TV e Refer to the instruction manual included with the Unscrew the M4 screws indicated by and wall mount when securing this TV to the wall remove the stand ee pp Also unscrew the M4 screws indicated by f you want to attach the stand of this TV again Please be careful with the TV after you insert the stand slowly as illustrated below and remove the stand drive M4 screws in the 4 threaded holes NOTE ny D e The M4 screws and stand you have removed are necessary for reattachment at a later date Make sure to keep them in a safe place lN 3 Attach the left and right TV rails to this TV using the four Phillips screws M4 x 12mm bolt and four M4 M5 washers included with the wall mount kit You don t n
11. SCREEN DISPLAY MODE Each of 4 display modes can be selected in either 4 3 or 16 9 aspect ratios 1 Press SCREEN MODE to switch the TV aspect ratio 2 Press SCREEN MODE repeatedly until the nor mal screen displays pa NOTE O e Some programs may not offer all display mode options When the broadcast is sending 4 3 video When the broadcast is sending 16 9 video signal signal Sidebar y Full Ed Wide WZ Expand Cinema Sidebar Full Sidebar displays a 4 3 picture at its standard A picture is displayed at 16 9 size as it is 4 3 size Sidebars will be displayed on the right Zoom and left edges of the screen Zoom displays a 16 9 picture without changing Full its horizontal and vertical ratio at its maximum Full displays a 4 3 picture at a 16 9 size with size horizontal elongation necessary to fill the Cinema screen Cinema displays a 16 9 picture with vertical Cinema elongation Cinema displays a 4 3 picture at a 16 9 size Expand with less horizontal elongation necessary to fill Expand displays a 16 9 picture with horizontal the screen because a little bit of the top and elongation bottom edge of the screen will be cut off Wide Wide displays the center of the picture as original size and the outer sides of the picture will be elongated The size of the picture will depend on the original signal EN WATCHING TV SCREEN INFORMATION You can display the currently selected channel or other i
12. book as a perma nent record of your purchase to aid identification in case of theft Model No Serial No Date of Purchase Dealer Phone No Dealer Purchase from Dealer Address A NOTE ABOUT RECYCLING This product s packaging materials are recyclable and can be reused Please dispose of any materials in accordance with your local recycling regulations Batteries should never be thrown away or incinerated but disposed of in accordance with your local regu lations concerning chemical wastes EN IMPORTANT SAFEGUARDS PRECAUTIONS SUPPLIED ACCESSORIES e Owner s Manual e Remote control unit e Batteries 1EMN21950A NFOOGUD AA x 2 DooQo OOOO OOOU OUUD O i O O SS 00 C f you need to replace these accessories please refer to the PART NO with the illustrations and call our toll free customer support line found on the cover of this manual e Depending on your antenna system you may need different types of Combiners Mixers or Separator Splitters Contact your local electronics store for these items FEATURES e DTV TV CATV You can use your remote control to select channels which are broadcast in conventional analog standard definition and high definition formats Also cable subscribers can access their cable TV channels Program Information Display DTV only You can display the title contents and other information of the current DTV program o
13. eee eS eee ca eee veda cand EAE RE dea 19 SELECTING AUDIO CHANNELS rs 19 ACCESSING EXTERNAL DEVICES ss 20 CHANGING THE SCREEN DISPLAY MODE sers 21 SCREEN INFORMATION a a 22 SLEEP TIMER canes d xr ick a a wee OM Ook oR Ro RR Rc de OR CR dedi d Rc nC RR RR RR e 23 OPTIONAL SETTINGS x 5 isos cia ce hee E X ede S gie dC E ECCE ERE RC ios ORO C dde caedes 23 SETUP SCREEN mMREK I IT 23 PICTURE ADJUSTMENT esca nc id Xa dica cd P E rare be a 6 EE oa do a 24 CLOSED ICRP TION MRMMRMCCC 25 DTV CLOSED CAPTION ca ws cue wae noe A acr dt E ed eo aod wand be coe hee eb iw Grac Bod eee 26 CLOSED CAPTION STYLE llle 26 fe o a da ia a e dd 28 HOMI AUDIO aiceser a aer ata E ld a A a a dia da aa 30 MISCELLANEOUS cio ica a a E ee DR RR ee ee B CC T ee 31 ATTACHING A WALL MOUNT BRACKET SOLD SEPARATELY 0 000000 RR RR I 31 TROUBLESHOOTING GUIDE i2 i lka ram Rx ok Rx awe bbb wba X RO R RR CRCR A CR BOX CR BOR RODOR RO CR CR RAD 32 GLOSSARY euet Esci osos ieee uias ect ere kou d secu Ade hi e ie Uds Erde sod gare de ee E o deed 34 VPN ZN EIER 34 SPECIFICATIONS ere RR nnn nns 35 WARRANTY ccrr ee ee n nn nnn Back cover SYMBOLS USED IN THIS MANUAL The following is the description for the symbols used in this manual Analog TV operation Digital TV operation e
14. f neither symbol appears under the function heading operation is applicable to both EN SUPPLIED ACCESSORIES FEATURES CONTENTS Functions REMOTE CONTROL TOP AND REAR PANEL FUNCTION E FOIE SLEEP SLEEP button p23 Press to activate the sleep timer POWER button p12 Press to turn the TV on and off Number buttons p18 Press to select a channel SETUP button p23 Press to display on screen menu 4 A v buttons p12 To move left right up down through the items ENTER button p12 Press to confirm your selection BACK button p22 Press to return to previous menu operation VOL A V buttons p18 Press to adjust volume MUTE button p18 Press to turn sound on and off CH RETURN button p18 Press to return to previously viewed channel TV Bis SETUP V VOLUME A W CHANNEL A GS o o NOTE Er oe POWER y CH RETURN INPUT SELECT INPUT SELECT button p20 Press to access connected external devices like a DVD recorder or VCR AUDIO button p19 Cycles through audio options e Analog mode TV Selects audio mode e Digital mode DTV Selects audio language STILL button p19 Press to pause screen image SCREEN MODE button p21 Press to select screen aspect ratio INFO button e Analog mode TV p22 To display channel No signal type and TV setting e Digital mode DTV p22 To display channel information signal type and TV set
15. product or deliver the product freight prepaid in either its original packaging or packaging affording an equal degree of protection to any AUTHORIZED SERVICE CENTER FUNAI CORP will not reimburse you for any service done by unauthorized service providers without prior written approval To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries please contact us at FUNAI CORPORATION Customer Service Tel 1 800 256 2487 http www EmersonAudioVideo com 19900 Van Ness Avenue Torrance CA 90501 Printed in China 1EMN21950A L5005UF L5002UC Kk
16. qualified service personnel 19 DAMAGE REQUIRING SERVICE Unplug this TV from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged or frayed b If liquid has been spilled or objects have fallen into the TV c If the TV has been exposed to rain or water PRECAUTIONS Place your TV in a room with adequate ventilation d If the TV does not operate normally by following the operating instruc tions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified techni cian to restore the TV to its normal operation e If the TV has been dropped or damaged in any way f When the TV exhibits a distinct change in performance this indicates a need for service 20 REPLACEMENT PARTS When replacement parts are required be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock injury to persons or other hazards 21 SAFETY CHECK Upon completion of any service or repairs to this TV ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition 22 HEAT This TV product should be situated away from heat sources such
17. recharged they can overheat and rupture HDMI cable connection EN FUNCTIONS PREPARATION FOR USE CONNECTION This section describes how to connect your TV to an antenna cable box etc MAKE SURE YOU HAVE AN ANTENNA As DTV is only available over the air you need an antenna to receive a digital signal NOTE e Be sure your antenna or other source is connected properly before plugging in the power cord ANTENNA CABLE CONNECTION 1 When connecting your TV to an antenna Connect the Coaxial cable on your home outlet to the ANT IN jack of this TV 2 When connecting TV to cable TV company without box Connect the Coaxial cable on your home outlet to the ANT IN jack of this TV VHF UHF aa Rear of this TV 00000000 C Coaxial cable not included 00000000 Coaxial cable Cable TV not included company Once connections are completed turn on the TV and begin initial setup Channel scanning is necessary for the TV to memorize all available channels in your area Refer to INITIAL SETUP on page 12 NOTES e For your safety and to avoid damage to equipment please unplug the coaxial cable from the ANT IN jack before moving the unit e If you use an antenna in order to receive analog TV the same antenna generally will work for DTV reception Outdoor or attic antennas will be more effective than set top versions To easi
18. ENTER Cool Neutral and Warm ES cR Picture Mode LM cast ES ien LT olt et Settings g LANGUAGE Color Temp Ener avin Energy Saving Using 4 gt adjust brightness of backlight lt To bright gt To dark Energy Saving Off E 1 e The adjustment bar for picture quality item is displayed on the screen NOTE e To cancel the picture adjustment press SETUP 4 To exit the setup press SETUP CLOSED CAPTION You can view closed captioning cc for TV pro grams movies news and prerecorded tapes Closed captions refer to text of dialogue or descrip tions displayed on screen for the hearing impaired SETUP o4 e e 1 Display the setup screen e Press SETUP The following setup screen appears 2 Select DETAIL and press ENTER to confirm e Using A V select Closed Caption and press ENTER to confirm RED EXIT closed Caption E ere Ho E CHANNEL LU Dm R LANGUAGE 3 Select Conventional CC and press ENTER to confirm Closed Caption Conventional CC off DTV CC off KA PICTURE CC Style CHANNEL D DETAIL Ld LANGUAGE 4 Select the Closed Caption mode Closed Caption E EXIT DTV CC ol SN PICTURE CC Style Conventional CC E CHANNEL D DETAIL g LANGUAGE Using A Y select the desired closed caption then press ENTER e There are three display modes according to Caption Mode
19. ER PACKING MATERIALS ANY ACCESSORIES EXCEPT REMOTE CONTROL ANY COSMETIC PARTS COMPLETE ASSEMBLY PARTS DEMO OR FLOOR MODELS FUNAI CORP AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS PRODUCT THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED IN TO AN AUTHORIZED SERVICE CENTER THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT IF NO PROOF OF PURCHASE IS ATTACHED THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED IMPORTANT THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE IF AT ANY TIME DURING THE WARRANTY PERIOD YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT PLEASE CONTACT FUNAI CORP ATTENTION FUNAI CORP RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS To obtain warranty service you must take the
20. Font1 Font Color Font2 E CHANNEL Font Opacity Font3 ma DETAIL Back Color Font4 Back Opacity Font5 EZ LANGUAGE Edge Color Jont Edge Type FONT7 Font Size Font size of the displayed caption can be switched as below CC Style Closed Caption E EXIT User Setting EJ SS um ES Large PESA i coor middie ont Opacity Small me DETAIL Back Color Back Opacity f A LANGUAGE Edge Color Edge Type Font Color Font color of the displayed caption can be switched as below CC Style Closed Caption gt EXIT User Setting Font Style White om LE Font Size Black 1 l Font Color Red Al CHANNEL d Font Opacity Green Back Color Blue Bae Back Opacity Yellow El S LANGUAGE Edge Color ENTE E Edge Type Cyan um Font Opacity Font opacity of the displayed caption can be switched as below CC Style Closed Caption User Setting Font Style Font Size Font Color Font Opacity Solid i Back Color Flash Im DETAIL Back Opacity Translucent Im LANGUAGE Edge Color Transparent Edge Type Back Color Background color of the displayed caption can be switched as below CC Style Closed Caption ID EXIT User Setting Font Style White E 2 SS Font Size Black F Font Color Red E CHANNEL A Font Opacity Green Ta DETAIL Back Color Blue Yellow Back Opacity Z LANGUAGE Edge Color Magenta Edge Type Cyan Back Opacity
21. HANNEL and press ENTER to con firm e Using A F select Autoscan Channel E EXIT Autoscan r Channel List Fea PICTURE Manual Register Fe crane Antenna Ur DETAIL LANGUAGE e Press ENTER 3 For TV channels using A V select Air For CATV channels select Cable e Press ENTER Scanning and memorizing the channels auto matically starts Analog channels Digital channels SETUP C Exi e When the scanning and memorizing are com pleted the lowest memorized channel in the broadcasting will be displayed NOTES e If you connect a cable system directly contact the CATV installer e If you press POWER or SETUP during Autoscan this setting will be canceled e If there is no reception connected or a poor signal is detect ed a Hint will appear on screen once scanning stops INITIAL SETTINGS CHANNEL SETTINGS 13 EN CHANNEL LIST This function lets you remove undesired channels from the Channel Registration List SETUP o4 E Co 1 Display the setup screen e Press SETUP The following setup screen appears 2 Select CHANNEL and press ENTER to con firm Using A V select Channel List Channel 2 EXIT 2 PICTURE Manual E DETAIL Ez LANGUAGE e Press ENTER 14 EN 3 Select the channel you want to remove e Using A F select the channel Channel List ge S 2 EXIT Highlight c
22. N ACCESSING EXTERNAL DEVICES Use your remote control to access DVD recorders home audio systems and other external devices when they are connected to your television Use your remote control to select external com 20 EN ponent e When you press INPUT SELECT or CH V on the remote control the input mode will be switched as below TV DTV channel y y y y Pressing CH A on the remote control reverses direction e To use the VIDEO1 or S VIDEO input jack on the TV select Video1 e To use the VIDEO2 or S VIDEO input jack on the TV select Video2 e To use the COMPONENT1 input jacks on the TV select Component1 To use the COMPONENT input jacks on the TV select Component2 To use the HDMI IN jack on the TV select HDMI e When you press INFO the current external input mode the type of resolutions for video signal TV aspect ratio CC and TV rating will be displayed at the top right of the screen e The information display will automatically dis appear in 1 minute 1 When using VIDEO1 or S VIDEO input jack Video1 MENTES a TV PG DLSV Ge 2 When using VIDEO2 or S VIDEO2 input jack Video2 MENTES a a TV PG DLSV Ge 3 When using COMPONENT input jacks Componenti DEAD a NONE 4 When using COMPONENT2 input jacks Component2 EGET 8 NONE 5 When using HDMI IN jack HDMI IAEA E ETE CHANGING THE
23. NAI CORP will provide parts to replace defective parts without charge for one 1 year from the date of original retail purchase Certain parts and LCD image burn in are excluded from this warranty LABOR FUNAI CORP will provide the labor without charge for a period of ninety 90 days from the date of original retail purchase LIMITS AND EXCLUSIONS THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER A PURCHASE RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY This warranty shall not be extended to any other person or transferee This warranty is void and of no effect if any serial numbers on the product are altered replaced defaced missing or if service was attempted by an unauthorized service center This limited warranty does not apply to any product not purchased and used in the United States This warranty only covers failures due to defects in material or workmanship which occur during normal use It does not cover damage which occurs in shipment or failures which are caused by repairs alterations or products not supplied by FUNAI CORP or damage which results from accident misuse abuse mishandling misapplication alteration faulty installation improper maintenance commercial use such as hotel rental or office use of this product or damage which results from fire flood lightning or other acts of God THIS WARRANTY DOES NOT COV
24. ONENTI1 input jack connect audio cables to the AUDIO L R jacks of COM PONENTI1 If you connect to your TV s COMPONENT input jack connect audio cables to the AUDIO L R jacks of COM PONENT2 Component video cable not included To component video To COMPONENT1 output jacks input jacks COMPONENT VIDEO OUT Y Pb Ex Pr DVD Player with the component a video output jacks o To audio output jacks Rear of this TV input jacks Audio cable not included NOTE e This TV accepts 480i 480p 720p 1080i video signals S VIDEO CABLE CONNECTION Offers good picture quality for video devices connected to your TV Use an S video cable not included to connect your TV to external video devices equipped with S video con nectors If you connect to your TV s S VIDEO input jack connect audio cables to the AUDIO L R jacks of VIDEO1 If you connect to your TV s S VIDEO input jack connect audio cables to the AUDIO L R jacks of VIDEO2 To S VIDEO S video cable not included input jack To S Video output jack Ex AUDIO VIDEO S VIDEO OUT OUT OUT R QQO DVD VCR with the S Video output jack To audio output jacks To AUDIO Rear of this TV input jacks Audio cable not included NOTE e If you connect to the S VIDEO jack and the VIDEO jack at the same time the S Video connection will have priority
25. Sas in lm DETAIL Reset Settings Ez LANGUAGE ColorTe ee Energy Saving 3 Adjust the picture quality e Using A V select the picture quality you want to adjust Picture Mode Using A Y adjust Picture Mode from the selection then press ENTER Standard Dynamic Movie and News Picture gt cx Picture Mode Fea PicTURE E CHANNEL con in Ma DETAIL eset settings g LANGUAGE ColorTe ner avin Brightness Using lt gt adjust until the darkest parts of the picture are as bright as you prefer lt To decrease brightness P To increase brightness Brightness 30 CE I 24 EN Contrast Using gt adjust to increase or decrease contrast lt To decrease contrast gt To increase contrast Contrast Color Using lt gt adjust to be brilliant or pale color lt To pale P To brilliant Color LU Ac Tint Using 44 gt adjust to obtain natural skin tones lt To red P To green EN Adjust Sharpness Using 4 gt adjust the detail of the picture lt To soft P To clear Sharpness 0 Gang A D 1 Adjus f Move Reset Settings Using A Y select Reset You can reset setting of the Picture Mode you select Reset Settings B EY Fea PicTuRE A CHANNEL Tra pera E tancuace Color Temp Using A F adjust Color Temperature from the selec tion then press
26. TAIL Ez LANGUAGE Press ENTER The password entry screen is displayed fz CHANNEL Enter password D DETAIL Ez LANGUAGE eee BACK 33 PIN Code Back 28 EN e When you have not set up your password enter 0000 e When the password is correct the following V Chip screen is displayed A MPAA Rating BJ TV Rating IC New Password EA LANGUAGE See the following description for setting each item A MPAA Rating 4 Display the MPAA Rating screen Using A Y select MPAA Rating L NIMM E CHANNEL m DETAIL ES LANGUAGE Press ENTER V Chip gt EXIT FJ PICTURE 1 CHANNEL m DETAIL g LANGUAGE 5 Set MPAA Rating Using A Y select the rating e Press ENTER and set to View or Block TESE Mg pera Iz LANGUAGE 6 To exit the setup press SETUP Selection lt Rating Category Explanations gt X Mature audience only NC 17 No one under 17 admitted R Restricted under 17 requires accompanying parent or adult guardian Unsuitable for children under 13 Parental Guidance suggested General Audience No Rating NOTES e When you select a rating and set it to Block the higher ratings will be blocked automatically The lower ratings will be available for viewing e When you set X to View all ratings turn to View automatically TV Rating 4 Display the TV Rating
27. To exit settings e J eis You can adjust the picture quality Picture Mode Brightness Contrast Color Tint Sharpness Color Temp and Energy Saving Refer to PICTURE ADJUSTMENT on page 24 You can automatically scan the viewable channels and remove those that are undesired Refer to AUTOSCAN on page 13 EN You can change closed captioning display formats and font styles Refer to CLOSED CAPTION on page 25 Block children s access to inappropriate program ming Refer to V CHIP on page 28 And select HDMI Audio if your TV is connected to a digital external device like a DVD recorder Refer to HDMI AUDIO on page 30 You can change the language English Spanish French displayed on the setup screen Refer to LANGUAGE SELECTION on page 17 NOTE e To cancel the setup screen press SETUP WATCHING TV OPTIONAL SETTINGS 23 EN PICTURE ADJUSTMENT You can select from four default picture color set tings You can also adjust brightness contrast color tint sharpness and color temperature as well as energy saving settings 1 Display the setup screen Display the setup screen e Press SETUP The following setup screen appears 2 EXIT PICTURE pS s z LANGUAGE 2 Select PICTURE and press ENTER to con firm Using A Y select your desired item and press ENTER to confirm Picture E EXIT fy PicrURE fz CHANNEL
28. To exit the setup press SETUP CHANNEL SETTINGS 17 EN W atcuine TV CHANNEL SELECTION Select channels by pressing CH a v found on remote control or on the TV s control panel or by pressing the Number buttons found on the remote control 18 EN CH RETURN CH A V Use CH A V to change the channel e Same operation is also available with CHAN NEL A V on the top panel of the main unit the Number buttons e Press the channel number with the Number buttons to select a channel you want to watch then press ENTER When selecting analog channel 12 0 0 9 When selecting digital channel 12 1 Be sure to press before entering the minor channel number 0 0 0 0 9 e f the channel broadcasts NTSC and ATSC both and you don t press you will receive the NTSC channel only The moment you press the lowest memorized digital channel will be dis played e Press CH RETURN to return to the previously viewed channel NOTE e In DTV broadcasting one channel sometimes broadcasts multiple programs depending on the air time In this case the main channel is called major channel and the minor channel is called minor channel About minor channel broadcasting There may be different programs being broad cast on minor channels through a single chan nel from ATSC You can watch each minor channel program being broadcast by selecting one of the minor channels NTSC ATSC
29. as radiators heat registers stoves or other products including amplifiers that produce heat Keep your TV set away from sources of direct heat such as heat registers or direct sunlight e Do not place your TV on soft surfaces such as rugs or blankets eave enough room for air to circulate around the bottom top and back of the set FCC WARNING This equipment may generate or use radio frequency energy Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the owner s manual The user could lose the authority to operate this equipment if an unauthorized change or modification is made CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT ATTENTION POUR EVITER LES CHOCS ELECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU AU FOND Note to CATV system installer This reminder is provided to call the CATV system installer s attention to Article 820 40 of the NEC that provides guidelines for proper grounding and in particular specifies that the cable ground should be connected to the grounding system of the building as close to the point of cable entry as practical The serial number of this product may be found on the back of the TV No others have the same serial num ber as yours You should record the number and other vital information here and retain this
30. be completed suc cessfully and Unavailable will be displayed on the screen CHANNEL SETTINGS 15 EN ANTENNA CONFIRMATION Displays signal strength for each channel 1 Display the setup screen e Press SETUP The following setup screen appears MO PICTURE 2 Select CHANNEL and press ENTER to con firm e Using A V select Antenna ies PICTURE Ez CHANNEL Ma DETAIL e Press ENTER Using the Number buttons or CH A V select the channel for which you want to check signal strength l Antenna 75 EXIT g 1 PICTURE r v 223 CHANNEL A Now 70 Peak 80 Im DETAIL V LANGUAGE 16 EN e f the channel is set to external input you can not confirm the antenna situation Video1 Antenna m EXIT pex PICTURE Es CHANNEL lm DETAIL EA LANGUAGE 3 To exit the setup press SETUP LANGUAGE SELECTION You can choose English Spanish or French as your on screen language SETUP E gt 1 Display the setup screen e Press SETUP The following setup screen appears POR PICTURE la DETAIL E LANGUAGE 2 CHANNEL 2 Select LANGUAGE and press ENTER to con firm Using A V select English Espanol or Francais Language ES Select the language for setup display 2 UE reum de preparaci n J H CHANNEL rancais lr DETAIL 2777 e Press ENTER 3
31. e exactly e Interference may cause the closed caption system not to function properly e The caption or text characters will not be displayed while the menu display or functions display is shown e If a black box appears on the screen this means that the TV is set to TEXT mode To clear screen select CAPTION CC1 CC2 CC3 CC4 or Off 25 EN OPTIONAL SETTINGS DTV CLOSED CAPTION D Apart from closed captions DTV has its own closed captions called DTV CC Use this menu to change the settings for DTV CC 1 Display the setup screen e Press SETUP The following setup screen appears 2 Select DETAIL and press ENTER to confirm Using A Y select Closed Caption and press ENTER to confirm PE ED E mre eg fz CHANNEL LU Lm Z LANGUAGE 3 Select DTV CC and press ENTER to confirm Closed Caption Conventional CC off DTV CC Off CC Style Closed Caption PDSA Conven tional CC DTV CC PICTURE mE El CHANNEL DETAIL Y LANGUAGE e Using A F select the desired DTV Closed Caption then press ENTER Off Select if you do not want DTV CC This is the default Service 1 to Service 6 Select one of these before changing any other item in the Closed Caption menu Choose Service 1 under normal circumstances 5 To exit the setup press SETUP 26 EN CLOSED CAPTION STYLE 1 Display the setup screen Press SETUP The follo
32. e videotape containing captions might not have been read during copying Black box is displayed in the screen Text mode is selected for caption Select CC1 CC2 CCS CC4 or Off CH The LCD panel is manufactured to provide many years of useful life Occasionally a few non active pixels may appear as a fixed point of blue green or red This is not to be considered a defect in the LCD screen 33 34 GLOSSARY ATSC Acronym that stands for Advanced Television Systems Committee and the name of the digital broadcasting standards Aspect ratio The width of a TV screen relative to its height Conventional TVs are 4 3 in other words the screen is almost square widescreen mod els are 16 9 the screen is almost twice as wide as its height Component video This is a video signal format that conveys each of three principal colors of light red blue and green through different signal lines This allows the viewers to experience picture colors as origi nal as it is There are several sig nal formats including Y Pb Pr and Y Cb Cr Dolby Digital The system developed by Dolby Laboratories to compress digital sound It offers stereo sound 2ch or multi channel audio up to 5 Tch MAINTENANCE CABINET CLEANING e Wipe the front panel and other exterior surfaces of the TV with a soft cloth immersed in lukewarm water and wrung dry Never use a solvent or alcohol Do
33. eed to use the lock washers for mounting this TV 31 EN TROUBLESHOOTING GUIDE Before calling for service please refer to the following information No power No picture or sound No color Sound OK picture poor Picture distorted Weak picture Lines or streaks in picture Picture blurred Ghosts in picture Bars on screen Be sure the power cord is connected to outlet f a power failure occurs unplug the power cord for 30 minutes to allow the unit to reset itself e Check if the power is on e Check the outlet connection e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e View other TV channels The problem might be limited to the broadcasting station e Turn off the power and wait for about 1 minute then turn it on again e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e View other TV channels The problem might be limited to the broadcasting station e Adjust the Color in the setup screen e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e Electrical interference from nearby appliances may affect picture quality e Adjust Contrast and Brightness in the setup screen e View other TV channels The problem might be limited to the b
34. eiErnersorn 37 inch Digital Analog EMERSON AND THE G CLEF LOGO ARE REGISTERED TRADEMARKS L D V OF EMERSON RADIO CORP PARSIPPANY NEW JERSEY U S A Owner s Manual EWL3706 A EWL3706 HIGH DEFINITION TELEVISION EMEN TO RECEIVE DIGITAL ANALOG SIGNAL DOLBY DU por av YOU MUST CONNECT ANTENNA IF YOU NEED ADDITIONAL ASSISTANCE WITH SET UP OR OPERATING AFTER READING OWNER S MANUAL PLEASE CALL TOLL FREE 1 800 256 2487 OR VISIT OUR WEB SITE AT http www EmersonAudioVideo com WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLI ANCE TO RAIN OR MOISTURE CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION ro REDUCE THE RISK OF ELEC TRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL THIS SYMBOL INDICATES THAT DANGER OUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT The important note is located on the rear of the cabinet IMPORTANT SAFEGUARDS 1 2 EN READ INSTRUCTIONS All the safety and operating instructions should be read before the appliance is operated RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference HEED WARNINGS All warnings on the appliance and in the operat ing instructions should be adhered to FOLLOW INSTRUCTIONS All operating and use instructions should be
35. followed CLEANING Unplug TV from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning EXCEPTION A product that is meant for uninterrupted service and that for some specific reason such as the possibility of the loss of an authorization code for a CATV converter is not intended to be unplugged by the user for cleaning or any other purpose may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5 ATTACHMENTS Do not use attachments not recommended by the TV manufacturer as they may cause hazards WATER AND MOISTURE Do not use this TV near water for exam ple near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like ACCESSORIES Do not place this TV on an unstable cart stand tri pod bracket or table The TV may fall causing serious injury to some one and serious damage to the appliance Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the TV Any mounting of the appliance should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer An appliance and cart combina tion should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn AMEUBLES Cet appareil ne doit tre plac que sur
36. gnal has priority in this setting e Select Digital if you connected to digital device with HDMI jack for digital audio input signal e Select Analog if you connected to analog device with analog jacks for analog audio input signal 4 To exit the setup press SETUP MisceLLaneous ATTACHING A WALL MOUNT BRACKET SOLD SEPARATELY The following is a description of the method for attaching a wall mount to this TV When performing this operation refer to the instruction manual included with the wall mount kit You need the following wall mount unit commercially available for this TV EZLCDM 02 Market Link USA Inc www easymount com 44 CAUTION e Any damage caused by incorrectly attempting to mount this TV is not covered under the terms of the manufacturers warranty e This LCD Color TV may be used only with EZLCDM 02 manufactured by Market Link USA Inc Wall Mount Use with other wall mounts may result in instability causing possible injury Hear of this TV O00000000000000000000000000 1000000000008 0000000000001 000000000000000000000000000 000000000000000000000000000 000000000000000000 Ll A OOOOO0000000000000000000000 OO00OOOOOOOOOOOOOOOOOOO0OO0 oooooooooononnon B bY Dew V A
37. hannels for tion 2 PICTURE QA Ch Up Down key selec r DETAIL A LANGUAGE I e Press ENTER to highlight the channel select ed for removal You will not be able to select the channel again using CH A V To reactivate the removed channel highlight it and press ENTER e When you remove a major channel you remove its minor channels too NOTE e The channel with DTV indicated on the display is ATSC otherwise the channel is NTSC 4 To exit the setup press SETUP MANUAL REGISTER This function lets you manually add channels not memorized due to poor broadcast strength during AUTOSCAN 1 Display the setup screen e Press SETUP The following setup screen appears 2 Select CHANNEL and press ENTER to con firm Using A Y select Manual Register Channel L Autoscan Channel List Manual Register Antenna Ur DETAIL A LANGUAGE Press ENTER 3 Select the channel you want to add e Using the Number buttons select your desired channel Manual Register 2 EXIT For An E select 9 PICTURE For Digital nels you must perform Autoscan function CHANNEL A AAA m DETAIL E LANGUAGE e Select Register with ENTER 4 To exit the setup press SETUP NOTES e If set up completes successfully Registered to the Channel List is displayed e If Video 1 is being used set up will not
38. ing the broadcasting stations These are the numbers used for analog broadcasts Remote Control doesn t work e Check the antenna or cable connection to the main unit e Check the batteries of the remote control e Check if there is an obstacle between the sensor and the remote control Test the signal output If OK there might be remote sensor trou ble Refer to IR SIGNAL CHECK on page 34 Problems with Closed Caption Feature Misspelled captions are displayed e Closed captioning production companies may broadcast pro grams without correcting the misspelling in a live broadcast Captions are not entirely displayed or Captions that are delayed a few seconds behind the actual dialogue captions are delayed behind the dia are common for live broadcasts Most captioning production compa logue nies can display a dialogue to a maximum of 220 words per minute If a dialogue exceeds that rate selective editing is used to ensure that the captions remain up to date with the current TV screen dialogue Captions are displayed as a white e Interference from buildings or weather conditions may cause box captioning to be incomplete No caption is displayed in the Closed Broadcasting station may shorten the program to insert adver Caption supported program tisement The closed caption decoder cannot read the informa tion of the shortened program No caption is displayed when playing The videotape may be illegally copied or the caption signal th
39. ly switch between antenna and cable wires you can purchase an Antenna Selector commercially available e f you connect a cable system directly contact the CATV installer CONNECTION TO CABLE SATELLITE BOX 1 Connect the coaxial cable on your home outlet to the input jack of the CABLE SATELLITE box 2 Use another coaxial cable to connect the ANT IN jack of your TV to the output jack of the CABLE SATEL LITE box Required cables in 2 and connecting methods differ depending on the CABLE SATELLITE box For more informa tion please contact your cable satellite provider Ex Satellite Rear of this TV aisn Cable box or l Satellite box 90 E E xi eg E gt Cable TV Coaxial cable NEAN Coaxial cable ANTIN company not included not included EN CONNECTING OTHER DEVICES HDMI 1 High Definition Multimedia Interface HDMI uses the latest technology to ensure the signal maintains the highest degree of integrity from source to TV Both video and audio travel through a single cable HDMI cable not included To HDMI IN jack Ex HDMI OUT mut i Pe AUDIO OUT AUDIO To HDMI output jack Ae O HDMI IN DVD Player with the HDMI output jack COAXIAL Rear of this TV NOTES e This TV accepts 480i 480p 720p 1080i video signals and 32kHz 44 1kHz 48kHz audio signals e This TV accepts only 2 channel audio signal LPCM e You need to
40. m nearby appliances may affect picture quality e View other TV channels The problem might be limited to the broadcasting station Different color marks on screen e Move your TV away from nearby electric appliances Turn off the power and wait 30 minutes before turning it back on e View other TV channels The problem might be limited to the broadcasting station Poor reception on some channels e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e Electrical interference from nearby appliances may affect picture quality e View other TV channels The problem might be limited to the broadcasting station Picture OK sound poor e Electrical interference from nearby appliances may affect picture quality e View other TV channels The problem might be limited to the U broadcasting station 3 No reception of digital signals Make sure Autoscan has been completed Refer to AUTOSCAN on Lu page 13 Autoscan must be completed when you set up your TV for lt the first time or move it to a location where previously unavailable channels are broadcast Ti The selected channel may not be broadcasting O e When Autoscan is interrupted some channels will not be o received Make sure to complete Autoscan in the setup screen Channel changes automatically e Many digital channels have alternate channel numbers TV changes the numbers automatically to the ones signify
41. n function can be executed for either Air or Cable only once When you change the connection Air Cable set the Autoscan again Refer to page 13 e If you connect a cable system directly contact the CATV installer e When the scanning is not complete Helpful Hint will be displayed every time you turn on the power If you have previously registered channels when this screen appears you can select a channel with the Number buttons No channel is registered Press and hold ENTER key for 3 seconds Contact support hotline provided on manual or back of unit Sin canal registrado Mantenga oprimida la tecla ENTER durante 3 segundos Llame tel fono de apoyo en manual 0 atras de TV Pas de chaine consign Maintenir la touche ENTER press e 3 secondes Contacter numero d urgence dans manuel ou arri re appareil e Toll free customer support line can be found on the cover of this manual 12 EN ChanneL SETTINGS AUTOSCAN With AUTOSCAN your TV automatically scans and memorizes your area s viewable channels Activate AUTOSCAN when you turn on your TV for the first time change broadcast sources e g from antenna to CATV or move your TV to a different broadcast area o Qu NOTE e Make sure the TV is connected to antenna or cable 1 Display the setup screen e Press SETUP The following setup screen appears ies PICTURE fist Channel Tm DETAIL Ez LANGUAGE 2 Select C
42. n the screen e Autoscan This TV can automatically scan and memorize the channels receivable in your residential area This feature elimi nates the need of a difficult setting procedure e V CHIP This feature allows you to block children s access to inappropriate programs e Closed Caption Decoder This TV contains the built in Closed Caption Decoder that displays text across the screen It allows you to read the dialogue of a TV program or other information in the Closed Caption supported programs MTS SAP Tuner This feature allows you to select with the remote control your desired audio language e Auto Shut Off Function If there is no signal input from the antenna terminal and no operation for 15 minutes the unit will turn itself off automatically Choices for On Screen Menu Language Select your setup menu language English Spanish or French e Stereo Sound Function e Full Function Remote Control PLL Frequency Synthesized Tuning e ADMI Input This TV accepts 480i 480p 720p 1080i video signals and 32kHz 44 1kHz 48kHz audio signals e Component VIDEO Input This TV accepts 480i 480p 720p 1080i video signals e S VIDEO Input e AV Input e Analog Audio Output Digital Audio Output Coaxial e Resume This feature will automatically memorize settings if a power failure occurs EN Contents IMPORTANT SAFEGUARDS a a E 2 PRECAU IONS a Re ee eee 3 SUPPLIED ACCESSORIES
43. nformation such as the audio mode on the screen BACK ED INFO In the analog mode the current channel and the audio mode are displayed 1 Display the channel number and the audio mode Press INFO on the remote control The current channel number audio mode type of resolutions for video signal TV aspect ratio CC and TV rating are displayed at the top right of the screen To clear the display press BACK or INFO again 22 EN DTV In the digital mode the detailed information for the current channel such as the Program guide is dis played 1 Display the detailed information for the channel Press INFO on the remote control The currently selected program details are dis played on the screen e The following information is displayed 1 Program title 2 3 4 5 Broadcast station Program guide max 4 lines displayed Channel number gt o gt gt Audio language Other is displayed when the audio language cannot be acquired or the acquired languages are other than English Spanish or French 6 Effective scanning lines and scan mode 7 Program definition 8 Program aspect ratio 9 Program rating 10 CC Not available if the CC set to Off 1 2 4 Buffy Vampire Slayer HDTV A quarter century ago which may now qualify as the good old days of newspapering run of paper sales accounted for 80 percent of the indust
44. ng A Y select New Password m PICTURE TV Rating New Password al CHANNEL Ta DETAIL ES LANGUAGE Press ENTER 5 Change the password e Use the Number buttons on the remote con trol and enter the NEW 4 digit password e Enter password again in Confirm password space V Chip Enter password Confirm password 6 To exit the setup press SETUP NOTES e Make sure to enter the exact same new password as the Confirm password If they are different the space is cleared for reentering e Your password will be erased and return to the default 0000 when a power failure occurs or when you turn off the power using a wall switch If you forget the password unplug the power cord for 10 seconds to restore the pass word to 0000 EN HDMI AUDIO Set the method of sound input for HDMI jack SETUP o4 Co 1 Display the setup screen Press SETUP The following setup screen appears 2 Select DETAIL and press ENTER to confirm Using A Y select HDMI Audio and press ENTER to confirm 3 Switch the HDMI Audio Using A Y select the desired HDMI Audio then press ENTER Detail B EXIT aes Caption aljierorE bu HDMI Audio fz CHANNEL m DETAIL v LANGUAGE l e Select Auto if you connected to both digital device with HDMI jack and analog device for audio sources Digital audio input si
45. not spray insec ticide liquid near the TV Such chemicals may cause damage and discoloration to the exposed surfaces LCD CLEANING Wipe the LCD of the TV with a soft cloth Before cleaning the LCD disconnect the power cord SERVICING Should your unit become inoperative do not try to correct the problem yourself There are no user ser viceable parts inside Turn off the TV unplug the power cord and call our toll free customer support line found on the cover of this manual to locate an authorized service center HDMI High Definition Multimedia Interface Interface that supports all uncom pressed digital audio video formats including set top box DVD player or digital television over a single cable High Definition TV HDTV Ultimate digital format that produces high resolution and high picture quality LPCM Linear Pulse Code Modulation LPCM is a format that can have up to 8 channels of audio It is mainly used in music production The format samples and captures analog signals and transforms them into digital signals without compressing the sound data NTSC Acronym that stands for National Television Systems Committee and the name of the current ana log broadcasting standards Password A stored 4 digit number that allows access to parental control features SAP Secondary Audio Program Second audio channel delivered separately from main audio chan nel This audio channel is used a
46. r 5 minutes 2 Canceling Still function e The Still function will be canceled by pressing any button while Still function is working NOTE e Press any key except POWER to cancel still mode SELECTING AUDIO CHANNELS This section describes how to switch the audio in the analog mode and how to switch the audio lan guage in the digital mode AUDIO rT tv When you press AUDIO the currently selected audio mode will be displyed on the screen 6 SAP STEREO Press AUDIO to cycle through available audio channels When the broadcasting has all audio 11 51 0 ree When the broadcasting has stereo audio and monaural audio STEREO MONO STEREO When the broadcasting has SAP and monaural audio SAP MONO Bagi SAP ONO When the broadcasting is having only monaural UU oo cannot be switched STEREO Outputs stereo audio SAP Outputs second audio program MONO Outputs mono audio DTV When you press AUDIO the currently selected language and the number of available languages will be displayed on the screen 6 1 English 1 3 n Press AUDIO to cycle through available audio languages English 1 3 Spanish 2 3 t Other 3 3 e Available languages differ depending on the broadcast e The information display will automatically dis appear in one minute NOTE e Pressing AUDIO does not control external audio source WATCHING TV 19 E
47. rnal device from underneath ANT IN el for external video tl alle E equipment i e DVD 000000000000000000000 000000 o recorder COMPONENT1 and AUDIO jacks Component cable connection for external audio video devices Use component and audio out jacks of external device COMPONENT and S VIDEO1 jack S Video cable and audio VIDEO1 cable connection for external video equipment S VIDEO2 jack S Video cable and audio VIDEO2 cable connection for external video equipment AUDIO jacks Component cable connection for external VIDEO2 and AUDIO jacks VIDEO1 and AUDIO jacks audio video devices Use Video and audio cable Video and audio cable component and audio out connection for external connection for external jacks of external device equipment equipment INSTALLING THE BATTERIES Install two AA batteries included matching the polarity indicated inside battery compartment of the remote control BATTERY PRECAUTIONS Be sure to follow the correct polarity as indicated in the battery compartment Heversed batteries may cause damage to the device Do not mix different types of batteries together e g Alkaline and Carbon Zinc or old batteries with fresh ones e f the device is not to be used for a long period of time remove the batteries to prevent damage or injury from possible battery leakage e Do not try to recharge batteries not intended to be
48. roadcasting station e When the outside antenna is used check the wire condition and connection e View other TV channels The problem might be limited to the broadcasting station e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e Adjust Contrast and Brightness in the setup screen e View other TV channels The problem might be limited to the broadcasting station e When the outside antenna is used check the wire condition and connection e Electrical interference from nearby appliances may affect picture quality e View other TV channels The problem might be limited to the broadcasting station e When the outside antenna is used check the wire condition and connection e View other TV channels The problem might be limited to the broadcasting station e Check the antenna or cable connection to the main unit e When the outside antenna is used check the wire condition and connection e Electrical interference from nearby appliances may affect picture quality e View other TV channels The problem might be limited to the broadcasting station e When the outside antenna is used check the wire condition and connection Electrical interference from nearby appliances may affect picture quality 32 Picture rolls vertically e When the outside antenna is used check the wire condition and connection e Electrical interference fro
49. ry s advertising revenues Department stores and supermarket were 3 9 10 NOTES e When the program guide is displayed in more than 5 lines use A Y to scroll e No description provided is displayed when the program guide is not provided e The following screen is displayed when con necting to external devices e g When using VIDEO input jack for con nection Video1 PEREA A TV PG DLSV GG SLEEP TIMER The Sleep Timer can be set to automatically turn off your television after an incremental period of time SLEEP 1 Press SLEEP on the remote control to set the Sleep Timer The setting display for Sleep Timer is shown on the screen 2 You can set your TV to turn off after a set period of time from 10 to 90 minutes After set up you can display the remaining time before shut off by pressing SLEEP again To cancel the sleep timer press SLEEP repeatedly until Sleep Off is displayed Sleep Off e The Sleep Timer setting display will automati cally disappear in a few seconds NOTE e When you disconnect your TV from its power source or when a power failure occurs the sleep timer setting will be cancelled ObrionaL SETTINGS SETUP SCREEN This section describes the overview of the setup screen displayed when you press SETUP For more details see the reference page for each item The setup screen consists of the function setting items below
50. s an alternate in bilingual broad casting Standard Definition TV SDTV Standard digital format that is sim ilar to the NTSC picture quality S Video Offers higher quality images by delivering each signal color c and luminance y independently of each other through separate cables IR SIGNAL CHECK If the remote control isn t working properly you can use an AM radio or digital camera including a cellu lar phone with built in camera to see if it is sending out an infrared signal e With an AM radio Tune the AM radio station to a non broadcasting frequency Point the remote control towards it push any button and listen If the sound from the radio flutters it is receiving the remote control s infrared signal With a digital camera including built in cell phone cameras Point a digital camera towards the remote control Push any button on the remote control and look through the digital camera If the infrared light appears through the camera the remote control is working Specirications GENERAL SPECIFICATIONS Television System Closed Caption System ATSC NTSC M TV Standard 15 119 FCC Analog CC 15 122 FCC Digital CC Channel Coverage ATSC NTSC VHF UHF CATV Tuning System Channel Access Terminals Antenna Input S Video Input Video Input Audio Input 2 13 14 69 2 13 A W W 1 W 94 A 5 A
51. screen Using A Y select TV Rating E xL MPAA Rating rex PICTURE TV Rating New Password E CHANNEL m DETAIL Z LANGUAGE Press ENTER FV V S EL ID T BACK View Block O Back 5 Set TV Rating Using A V select the rating e Press ENTER and set to View or Block for the rating without sub categories D EXIT T E PICTURE A CHANNEL D DETAIL g LANGUAGE For the rating with sub categories press A Y lt q gt and select the rating Then press ENTER and set to View or Block ieue E PES TV G a A BIN E en 3 BACK 5 View Block Back 6 To exit the setup press SETUP lt Selection gt TV MA TV 14 TV PG TV G TV Y7 Rating Category Explanations gt Mature audience only Unsuitable for children under 14 Parental Guidance suggested General Audience Appropriate for children 7 and older TV Y Appropriate for all children Selection Rating Sub Category Explanations gt Fantasy Violence Violence Sexual Situation Coarse Language Suggestive Dialogue NOTES e When you select a rating and set it to Block the higher ratings will be blocked automatically The lower ratings will be available for viewing e When you set TV MA to View all ratings turn to View automatically OPTIONAL SETTINGS 29 EN 30 New Password 4 Display the New Password screen Usi
52. select PCM for the digital audio output of the device you connect or the HDMI audio setting Audio sometimes makes no sound if you select Bitstream etc e This TV only accepts signals corresponding EIA861 2 When your video device has a DVI output jack connect the HDMI conversion cable not included from the DVI output jack HDMI DVI conversion cable not included To DVI output jack To HDMI IN jack DVI OUT 44444447 444447740 77 444444707 _ _ cc 0 AAA AUDIO OUT R L Q Cable Box or Satellite Box FOIS CUT COAXIAL with the DVI output jack To AUDIO Rear of this TV input jacks To audio output jacks Audio cable not included NOTES e This TV accepts 480i 480p 720p 1080i video signals e An HDMI conversion cable requires a separate audio cable connection as well e Audio signals are converted from digital to analog if you make the connection in paragraph 2 above e DVI does not show image if the 480i does not accept EIA CEA 861 861B HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC EN PREPARATION FOR USE COMPONENT CABLE CONNECTION Offers better picture quality for video devices connected to your TV Use a component video cable not included to connect your TV to external video devices equipped with component video jacks If you connect to your TV s COMP
53. ting e External input mode p20 To display external input mode signal type and TV setting CH A Y buttons p18 p20 To select channels and external input mode SETUP button p23 To display on screen menu VOLUME A V buttons p18 To adjust volume and move right A left V through the menu items CHANNEL A V buttons p18 To select channels and move up down through the menu items POWER button p12 To turn TV on off INPUT SELECT ENTER button p20 p12 e To access connected external devices like a DVD recorder or VCR To decide the command of setting when the menu is displayed Infrared Sensor Window Receives infrared rays transmitted from the remote control e With buttons VOL A V or MUTE you can only adjust the volume of the main unit You cannot adjust the volume of the external devices with these buttons EN ANT IN jack AUDIO OUT jacks Coaxial cable connection for Audio cable connection for external your antenna or cable box audio equipment Use AUDIO IN jacks of external equipment AUDIO jacks for DVI connection Audio cable connection for external audio video devices with DVI jack Use AUDIO OUT jacks of external equipment when using an HDMI DVI conversion cable HDMI IN jack DIGITAL AUDIO OUT COAXIAL jack Digital audio coaxial cable connection for decoder or AUDIO OUT AUDIO audio receiver Connect cable 35 O O O SS to DIGITAL AUDIO IN jack of exte
54. un meuble avec ou sans roulettes recommand par le fabricant Si vous l in stallez sur un meuble roulettes d placez les deux ensembles avec pr caution Un arr t brusque l utilisation d une force excessive et des surfaces irr guli res risquent de d sta biliser l ensemble et de le renverser VENTILATION Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by placing the TV on a bed sofa rug or other similar surface This TV should never be placed near or over a radiator or heat register This TV should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufac turer s instructions have been adhered to PORTABLE CART WARNING SYMBOLE D AVERTISSEMENT POUR LES C APPAREIL ET MEUBLE A ROULETTES THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAIN TENANCE INSTRUCTIONS IN THE LITERA TURE ACCOMPANYING THE APPLIANCE 10 POWER SOURCES This TV should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your appliance dealer or local power company For TVs intended to operate from battery power or other sources refer to the operating instructions
55. wing setup screen appears FD EXIT E PICTURE A CHANNEL lir DETAIL Ez LANGUAGE 2 Select DETAIL and press ENTER to confirm Using A Y select Closed Caption and press ENTER to confirm L Detail D EXIT Closed Caption 5 V chip O 7 D A E CHANNEL m DETAIL Z LANGUAGE 3 Select CC Style and press ENTER to confirm Closed Caption LEN Conven tional CC DTV CC o PICTURE E CC Style EA CC Style E EXIT User Setting Fon RA PICTURE fz CHANNEL D DETAIL Y lieu Using A Y select the desired Closed Caption Style 5 Use User Setting e The User Setting function lets you change CC style e Using A F select User Setting Press ENTER and set User Setting to On CG Style 2 TPES L ENTE E 6 Set each item e When User Setting is set to On you can set the following items CC style set by User Setting will be displayed e Using A F select the item you want to set e You can switch the setting for each item with A V Picture display ABCDEFGHIJKL Edge Edge Color and Edge Type Font Font Style Font Size Font Color and Font Opacity Back Back Color and Back Opacity e The setting description for each item is shown below Font Style Closed Captioning font style can be changed as below CC Style Closed Caption ES EXIT User Setting E Font Style Fonto eal PICTURE Font Size
Download Pdf Manuals
Related Search