Elkay EDF14C User's Manual
Contents
1. EDF14C Installation Care Use Manual bw m SEE FIG 2 15 a Installer To assure you install this model easily and correctly PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION CHECK YOUR INSTALLA TION FOR COMPLIANCE WITH PLUMBING ELECTRICAL AND OTHER APPLICABLE CODES After installation leave these instructions inside the fountain for future reference IMPORTANT ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON IMPORTANT INSTALLER PLEASE NOTE THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE COMPUTERS ETC TO WATER LINES IS A COMMON PROCEDURE THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTOA FOUNTAIN CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM INSTALLATION INSTRUCTIONS Wall should already be framed for the fountain using the positioning dimensions shown in Figure 1 Shown dimensions pertain to installation location framing must support up to 150 Ibs weight Install rough in plumbing as shown in Figure 1 Waste line should extend a minimum of 2 51mm through the back panel Connect i2. an cause water flow to spurt or not regulate Mineral deposits may be removed from orifice with a small round file not over 1 8 diameter or a small diameter wire CAUTION Do not file or cut orifice materials 97256C Rev A 4 05 EDF14C 6 7 8 175mm 4 102 1 15 16 40 1016 FLOOR LINE LEGEND A RECOMMENDED WATER SUPPLY LOCATION 3 8 0 D TUBE CONNECT STUBBED 1 25mm FROM WALL SHUT OFF BY OTHERS B RECOMMENDED LOCATION FOR WASTE OUTLET 1 1 4 0 D DRAIN STUBBED 6 5 8 168mm FROM WALL 1 1 4 TRAP FURNISHED D 1 4 6mm DIA HOLES FOR SECURING FOUNTAIN TO WALL PARTS LIST ITEM gt PARTNO DESCRIPTION LK142 BUBBLER ASSY 40089C COVER NUT 40048C BUTTON 10031C RETAINING NUT 61313C REGULATOR A52919 O RING 40319C ORIFICE FITTING 50314C ORIFICE FLOW STRAIGHTNER 45675C BUBBLER BODY A54800 NIPPLE 100322740560 GASKET A54888 SCREEN 72460042 WASHER 70012C LOCKNUT 3 8 18 28577C FOUNTAIN BODY LK464 DRAIN PRINTED IN U S A FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1 800 323 0620 ELKAY MANUFACTURING COMPANY 2222 CAMDEN COURT OAK BROOK IL 60523 630 574 8484 97256C Rev A 4 05 PAGE 2
3. ng lines to be copper and thoroughly flushed to remove all foreign matter before connection to fountain Run the supply water inlet line through the back panel Install a service stop not provided Turn on supply water and flush thoroughly Secure the fountain to the wall using 6 bolts and washers not provided Tighten securely Remove elbow from end of p trap and attach it to drain tube Reattach elbow to and cut waste tube to required length using plumbing hardware and trap as a guide Make water supply connections from service stop to the fountain Turn on water supply and check for leaks Newly installed water supply line should be insulated after leak check is completed These products are designed to operate on 20 105 PSIG supply line pressure If inlet pressure is above 105 PSIG a pressure regulator must be installed in the supply line Any damage caused by reason of connecting these products to supply line pres sures lower than 20 PSIG or higher than 105 PSIG is not covered by warranty Check stream height from bubbler Stream height is factory set at 35 PSI If supply pressure varies greatly from this turn adjustment screw on the regulator Item 5 Clockwise adjustment will raise stream height and counter clockwise will lower stream height For best adjustment stream should hit basin approximately 6 1 2 165mm from bubbler TROUBLE SHOOTING AND MAINTENANCE Orifice Assy Mineral deposits on orifice c
Download Pdf Manuals
Related Search