Electrolux ESL 43020 User's Manual
Contents
1. gent Let the door stay ajar for some minutes before you remove the dishes Fill the rinse aid dispenser with rinse aid 446 mm 818 898 mm 550 mm 0 5 bar 0 05 MPa 8 bar 0 8 MPa maximum 60 C 9 photovoltaic panels and aeolian use a hot water supply to decrease energy consumption If the hot water comes from alternative sources of energy e g solar panels ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be electrolux 15 caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Recycle the materials with the symbol amp Put the packaging in applicable containers to recycle it www electrolux com shop DAQE 117943791 A 502010 CE2. a small quantity of de tergent on the inner side of the appli ance door 4 If you use detergent tablets put the tab let in the detergent dispenser 5 Close the lid until it locks into position i Use long washing programmes when you use detergent tablets Detergent tablets do not fully dissolve with short washing programmes and can de crease the washing results Use of rinse aid Rinse aid makes it possible to dry the dishes without streaks and stains Rinse aid is automatically added during the last rinsing phase To fill the rinse aid dispenser 1 Press the release button R to open the lid g 2 Fill the rinse aid dispenser Ef with rinse aid The mark max shows the maxi mum level 3 Remove the spilled rinse aid with an ab sorbent cloth to prevent foam during the washing programme 4 Close the lid until it locks into position Fill the rinse aid dispenser when the lens is transparent Adjust the rinse aid dosage Factory set position 3 You can set the rinse aid dosage between position 1 lowest dosage and position 4 highest dosage Turn the rinse aid selector EX to increase or decrease the dosage Using combi detergent tablets These tablets contain agents as detergent rinse aid and dishwasher salt Some types of tablets can contain other agents When you use tablets that contain salt and rinse aid do not fill the salt container and rinse aid dispenser Be sure that these tab
3. appliance with salt before you start a washing programme Remaining salt in the appliance can cause corrosion or make a hole in the bottom of the appli ance e Do not fill the rinse aid dispenser with other products than the rinse aid dish washer cleaning agent liquid detergent This can cause damage to the appliance e Make sure that the spray arms can move freely before you start a washing pro gramme e The appliance can release hot steam if you open the door while a washing pro gramme operates There is a risk of skin burns e Do not remove the dishes from the appli ance until the washing programme is completed Care and cleaning e Before you clean the appliance deacti vate it and disconnect the mains plug from the mains socket e Do not use flammable products or prod ucts that can cause corrosion e Do not use the appliance without the fil ters Make sure that the installation of the filters is correct An incorrect installation causes unsatisfactory washing results and damage to the appliance e Do not use spray water or steam to clean the appliance Risk of electrical shock and damage to the appliance Installation e Make sure that the appliance is not dam aged Do not install or connect a dam aged appliance contact the supplier e Remove all packaging before you install and use the appliance e Only a qualified person must do the elec trical connection the plumbing and the installation o
4. higher position 4 Put back the front runner stops A in their initial position Caution If the basket is in the higher position do not put cups on the cup racks SELECT AND START A WASHING PROGRAMME Starting the washing programme 1 Activate the appliance Make sure that the appliance is in setting mode 2 To set a washing programme press the programme button again and again until the related programme indicator comes on 3 Close the appliance door the washing programme starts automatically Interruption of a washing programme e Open the appliance door The washing programme stops e Close the appliance door The washing programme continues from the point of interruption Cancelling the washing programme If the washing programme has not started you can change the selection To change the selection while a washing programme operates it is necessary to cancel the programme 1 Open the appliance door 2 Press and hold the programme button until the programme indicator goes off and the end indicator starts to flash Make sure that there is detergent in the detergent dispenser before you start a new washing programme End of the washing programme When the washing programme is comple ted an intermittent acoustic signals sounds 1 Open the appliance door e The end indicator is on 2 Deactivate the appliance electrolux 11 For better drying results keep the ap e First remove the i
5. socket The fuse in the fuse box is damaged Model MOD If the malfunction occurs again contact the service centre If the different alarm codes show contact the service centre The necessary information for the service centre is on the rating plate Clean the water tap Contact your local water au thority Open the water tap Clean the filter Make sure that the connection is correct Make sure that the water inlet hose has no damages Clean the sink spigot Make sure that the connection is correct Make sure that the water drain hose has no damages Close the water tap and con tact the service centre Close the appliance door Connect the mains plug Replace the fuse Record this information Product number PNC Serial number S N cece The washing results and drying results are not satisfactory Problem Possible cause Possible solution The dishes are not clean The selected washing pro gramme was not applicable for the type of load and soil Make sure that the washing programme is applicable for the type of load and soil 14 electrolux Problem Possible cause Possible solution Limescale particles on the dishes There are streaks milky stains or a bluish layer on glasses and dishes Dry water drop stains on glasses and dishes The dishes are wet The dishes are wet and dull TECHNICAL DATA Dimensions
6. the appli your area ance Contact your local water authority to know the water hardness in your area Water hardness ad Water hardness justment German degrees French degrees mmol l Clarke de dH TH grees Sil 70 91 125 Si 125 64 88 21 10 43 50 76 90 7 6 9 0 53 63 21 87 42 65 75 6 5 7 5 46 52 21 29 36 51 64 5 1 6 4 36 45 21 23 28 40 50 4 0 5 0 28 35 21 19 22 33 39 3 3 3 9 23 27 21 51 1S 18 26 32 2 6 3 2 18 22 il 4 il 14 19 25 1 9 2 5 1317 1 electrolux 7 Water hardness ad Water hardness justment German degrees French degrees mmol l Clarke de Kela TH grees 4 10 7 18 0 7 1 8 5 12 1 2 lt 4 lt 7 lt 0 7 lt 5 42 42 1 Factory position 2 Do not use salt at this level You must adjust the water softener to flash and the programme indicator B manually and electronically comes on 4 When the programme indicator B goes Manual adjustment off and the i indicator starts to fon Turn the water hardness dial to the position press the programme button The pro 1 or 2 refer to the table gramme indicator A continues to flash The electronic adjustment of the water softener is activated 5 The end indicator shows the setting of the water softener The number of flash es of the end indicator is the same as the water hardness level example 5 flashes pause 5 flashes level 5 6 Press the programme button to cha
7. Thinking oF pri user manual Electrolux Dishwasher ESL 43020 2 electrolux Electrolux Thinking of you Share more of our thinking at www electrolux com CONTENTS Safety information Product description Control panel Use of the appliance Setting the water softener Use of dishwasher salt Use of detergent and rinse aid Loading cutlery and dishes NO OO O1 BR N A SAFETY INFORMATION Before the installation and use read this manual carefully e For your safety and the safety of your property e To help the environment e For the correct operation of the appli ance Always keep these instructions with the ap pliance also if you move or give it to a differ ent person The manufacturer is not responsible if an in correct installation and use causes dam age Children and vulnerable persons safety e Do not let persons children included with reduced physical sensory reduced mental functions or lack of experience and knowledge to use the appliance They must have supervision or instruction for the operation of the appliance by a person who is responsible for their safety e Children must get supervision to make sure that they do not play with the appli ance e Keep all packaging away from children There is the risk of suffocation or injury e Keep all detergents in a safe area Do not let the children touch the detergents e Keep children and pets away from the appliance when the door i
8. Water supply pressure Water supply Capacity The baskets were not loaded correctly water did not touch all surfaces The spray arms could not turn freely because of incorrect ar rangement of the load The filters are dirty or not as sembled and installed correctly The quantity of detergent was not sufficient or missing The salt container is empty Incorrect water softener adjust ment The salt container cap is not closed correctly Rinse aid dosage is too high Rinse aid dosage is too low The detergent can be the cause You have set a washing pro gramme without drying phase or with a decreased drying phase The rinse aid dispenser is emp ty Width Height Depth Minimum Maximum Cold water or hot water Place settings 1 Connect the water inlet hose to a water tap with a 3 4 thread The rating plate on the inner edge of the appliance door shows the electrical connection data Load the baskets correctly Make sure that an incorrect ar rangement of the load does not cause a blockage of the spray arms Make sure that the filters are clean and correctly assembled and installed Make sure that the quantity of detergent is sufficient Fill the salt container with dish washer salt Adjust the water softener Make sure that the salt contain er cap is closed correctly Decrease the rinse aid dosage Increase the rinse aid dosage Use a different brand of deter
9. an If the detergent gets into the eyes contact immediately a physician and clean the eyes with water Keep dishwasher detergents in a safe area and out of children touch Do not keep the appliance door open when there is detergent in the detergent dispenser Fill the detergent dispenser only be fore you start a washing programme EX Rating plate Filters EJ Lower spray arm EJ Upper spray arm CONTROL PANEL The controls are on the top on the con trol panel To operate with the controls keep the appliance door ajar electrolux 5 A B AE am dE oC orco of Ory a C y ITE On off button Programme indicators Indicators Programme button gt End indicator It comes on in these conditions e When the washing programme is completed e When you adjust the level of the water softener e When you deactivate or activate the acoustic signals e When the appliance has a malfunction Salt indicator It comes on when it is necessary to fill the salt container 1 After you fill the container the salt indicator can stay on for some hours This does not have an unwanted effect on the operation of the appliance 1 When the salt container is empty the related indicator does not come on while a washing programme operates On off button Press this button to activate or deactivate the appliance Programme indicators A and B These indicators have also an auxilia
10. f the appliance This to pre vent the risks of structural damage or in jury e Make sure that the mains plug is discon nected from the mains socket during in stallation e Do not drill into the sides of the appliance to prevent damage to hydraulic compo nents and electrical components e Important Obey the instructions in the template supplied with the appliance To install the appliance To assemble the door panel electrolux 3 To connect to the water supply and drain e Make sure that the appliance is installed below and adjacent to safe structures Frost precautions e Do not install the appliance where the temperature is less than O C e The manufacturer is not responsible for frost damage Water connection e Use new hoses to connect the appliance to the water supply Do not use used ho ses e Do not connect the appliance to new pipes or pipes not used for a long time Let the water flow for some minutes then connect the inlet hose e Make sure not to squash or cause dam age to the water hoses when you install the appliance e Make sure that the water couplings are tight to prevent a water leakage e The first time you use the appliance make sure that the hoses do not have water leaks Electrical connection e The appliance must be earthed e Make sure that the electrical information on the rating plate agrees with the power supply e Always use a correctly installed shock proof
11. ion flash to show an alarm code First try to find a solution to the problem re fer to the table If not contact the service centre e The programme indicator flashes continuously The appliance does not fill with water e The end indicator flashes one time intermittently electrolux 13 e The programme indicator flashes continuously e The end indicator flashes two times intermittently e The programme indicator flashes continuously e The end indicator flashes three times intermittently A Warning Deactivate the appliance before you do the checks The appliance does not drain the water The anti flood device is on Malfunction Possible cause Possible solution The appliance does not fill with water The appliance does not drain the water The anti flood device is on The start of the washing pro gramme does not occur After the check activate the appliance The programme continues from the point of in terruption The water tap is blocked or there is limescale on it The water pressure is too low The water tap is closed The filter in the water inlet hose is blocked The connection of the water in let hose is not correct The water inlet hose is dam aged There is a blockage in the sink spigot The connection of the water drain hose is not correct The water drain hose is dam aged The appliance door is open The mains plug is not connec ted in the mains
12. lets are applicable for the water hardness in your area refer to the instructions on the packaging of the prod ucts 1 Adjust the water hardness to the lowest level Refer to Setting the water soften er 2 Set the rinse aid dosage to the lowest position Refer to Use of detergent and rinse aid Using again separately detergent salt and rinse aid 1 Fill the salt container and the rinse aid dispenser 2 Adjust the water hardness to the highest level 3 Start a washing programme without dishes 4 When the washing programme is com pleted adjust the water softener to the water hardness in your area 5 Adjust the quantity of rinse aid LOADING CUTLERY AND DISHES Hints and tips e Do not put in the appliance items that can absorb water sponges household cloths e Remove the remaining food from the items e Make soft the remaining burned food on the items e Put hollow items cups glasses and pans with the opening down e Make sure that water does not collect in containers or in bowls Make sure that cutlery and dishes do not bond together Make sure that the glasses do not touch other glasses e Put small items in the cutlery basket e Mix the spoons with other cutlery to pre vent them to bond together e When you put the items in the baskets make sure that the water can touch all surfaces Put light items in the upper basket Make sure that the items do not move Water d
13. nge the adjustment Press the programme button again and again to change the setting When the programme button is pressed the level number increases Electronic adjustment 1 Activate the appliance _ 7 Deactivate the appliance to confirm 2 Make sure that the appliance is in set ting mode i If the water softener is set electronically 3 Press and hold the programme button to the level 1 the salt indicator stays until the programme indicator A starts off USE OF DISHWASHER SALT How to fill the salt container 1 Turn the cap counterclockwise and open the salt container 2 Fill the salt container with 1 litre of water only for the first time you fill with salt 3 Use the funnel to fill the salt container with salt 4 Remove the salt around the opening of the salt container 5 Turn the cap clockwise to close the salt container i It is correct that water comes out from the salt container when you fill it with salt 8 electrolux USE OF DETERGENT AND RINSE AID 1 NE Nie W A NNI a a Use of detergent To help the environment do not use more than the correct quantity of deter gent Obey the instructions on packaging of the detergent To fill the detergent dispenser 1 Press the release button BA to open the lid EX 2 Put the detergent in the detergent dis penser Ei 3 Ifthe washing programme has a pre wash phase put
14. ramme indicator A comes on and the programme indicator B starts to flash 5 Press the programme button again the end indicator goes off The acoustic sig nals are deactivated 6 Deactivate the appliance to confirm Activating the acoustic signals 1 To activate the acoustic signals again do steps 1 through 4 The pro gramme indicator A goes off and the end indicator is off The programme in dicator B continues to flash 2 Press the programme button again The end indicator comes on The acoustic signals are activated 3 Deactivate the appliance to confirm After some seconds the programme in dicator A goes off and the end indica tor comes on The programme indicator B continues to flash USE OF THE APPLIANCE 1 Be sure that the set level of the water softener agrees with the water hardness in your area If not adjust the water softener 2 Fill the salt container with dishwasher Load cutlery and dishes into the appli ance Set the correct washing programme for the type of load and soil Fill the detergent dispenser with the cor salt rect quantity of detergent 3 Fill the rinse aid dispenser with rinse aid 7 Start the washing programme SETTING THE WATER SOFTENER The water softener removes minerals and Adjust the level of the water softener if this salts from the water supply These minerals does not agree with the water hardness in and salts can cause damage to
15. roplets can collect on plastic items and non stick pans Lower basket Put the saucepans lids plates salad bowls and cutlery in the lower basket Arrange the service dishes and large lids around the edge of the basket ae gga 4 AAAA I i 1710000707 electrolux 9 Cutlery basket If the dimensions of the cutlery prevent use of the cutlery grid you can easily remove it Put the forks and spoons with the handles down Put the knives with the handles up Mix the spoons with other cutlery to prevent them to bond together Upper basket The upper basket is for plates maximum 24 cm in diameter saucers salad bowls cups glasses pots and lids Arrange the items to let water touch all surfaces 10 electrolux VN QO OX C A Put the glasses with long stems in the cup racks with the stems up For longer items fold the cup racks up Adjustment of the height of the upper basket You can put the upper basket in 2 positions to increase the load flexibility Maximum height of the dishes in the upper the lower basket basket Higher position 20 cm 31 cm Lower position 24 cm 27 cm Do these steps to move the upper basket to the higher position 1 Move the front runner stops A out 2 Pull the basket out 3 Put the basket in the
16. ry func tion when you e Adjust the level of the water softener e Activate or deactivate the acoustic sig nals Programme button With this button you can e Set a washing programme e Adjust the level of the water softener e Activate or deactivate the acoustic sig nals e Cancel a washing programme in opera tion Setting mode The appliance must be in setting mode for these operations e To set and start a washing programme e To adjust electronically the level of the water softener e To deactivate or activate the acoustic signals Activate the appliance The appliance is in setting mode when e All the programme indicators are off e The end indicator flashes Activate the appliance The appliance is not in setting mode when e Only one programme indicator comes on It is necessary to cancel the pro gramme to go back to the setting mode Refer to Setting and starting a washing programme Acoustic signals You can hear the acoustic signals in these conditions e The washing programme is completed e The appliance has a malfunction 6 electrolux i Factory setting on Deactivating the acoustic signals 1 Activate the appliance 2 Make sure that the appliance is in set ting mode 3 Press and hold the programme button until the programme indicator A flashes and the programme indicator B comes on 4 Press immediately the programme but ton again The prog
17. s open General safety e Do not change the specifications of this appliance There is the risk of injury and damage to the appliance Select and start a washing programme 10 Washing programmes 11 Care and cleaning 12 What to do if 12 Technical data 14 Environment concerns 15 Subject to change without notice e Obey the safety instructions from the de tergent manufacturer to prevent burns to eyes mouth and throat e Do not drink the water from the appli ance Particles of detergent can stay in your appliance e Do not keep the appliance door open without supervision This to prevent injury and to fall on an open door e Do not sit or stand on the open door Use e The appliance is only for domestic use Do not use the appliance for other uses to prevent injury to persons and damage to property e Only use the appliance to clean accesso ries that are applicable for dishwashers e Do not put flammable products or items that are wet with flammable products in near or on the appliance Risk of explo sion or fire e Put the knives and all items with sharp points in the cutlery basket with their points down If not put in a horizontal position in the upper basket or in the knife basket Not all models have the knife basket e Use only specified products for dish washers detergent salt rinse aid e Types of salt that are not specified for dishwashers can cause damage to the water softener e Fill the
18. socket e Do not use multiple plugs and extension cables There is a risk of fire e Do not replace or change the mains ca le Contact the service centre ake sure not to squash or cause dam age to the mains plug and cable behind the appliance e Make sure that there is access to the mains plug after the installation e Do not pull the mains cable to disconnect the appliance Always pull the mains plug e Only for UK and Ireland The appliance has a 13 amp mains plug If it is necessa ry to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse e ZT 4 electrolux Service centre e Only a qualified person can repair or work on the appliance Contact the service centre e Use only original spare parts To discard the appliance e To prevent the risk of injury or damage Disconnect the mains plug from the mains socket Cut off the mains cable and discard it Remove the door catch This prevents children or pets to be closed in the ap pliance There is a risk of suffocation Discard the appliance at the local waste disposal centre Warning The dishwasher detergents are dangerous and can cause corrosion PRODUCT DESCRIPTION Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser If an accident occurs with these de tergents contact immediately a physician If the detergent gets into the mouth contact immediately a physici
19. temperature the quantity of dishes can change the the variations of the mains supply and consumption values 12 electrolux CARE AND CLEANING To remove and clean the filters 8 Fully clean the parts with water Dirty filters decrease the washing results 4 Put the two parts of the filter A togeth Although the maintenance is very low with er and push Make sure that they en these filters make a check at intervals and gage correctly in each other Remove the filter B Fully clean the filter B with water Put the filter B to its initial position Make sure that it engages correctly in the two guides C if necessary clean them 1 Turn the filter A counterclockwise and remove it out from filter B NO 2 Filter A has two parts To disassemble the filter pull them apart 8 Put the filter A into position in filter B Turn the filter A clockwise until it locks To clean the spray arms Do not remove the spray arms If the holes in the spray arms become clog ged remove remaining parts of soil with a thin pointed object To clean the external surfaces Clean the external surfaces of the appliance and control panel with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads or solvents acetone WHAT TO DO FF The start of the appliance does not occur or With some malfunctions the indicators it stops during operat
20. tems from the lower pliance door ajar for some minutes basket then from the upper basket R the it f the basket e There can be water on the sides and on SONS tne Kems MOm Me see the door of the appliance Stainless steel e Let the dishes become cold before you becomes cool more quickly than the remove them from the appliance Hot dishes dishes can be easily damaged WASHING PROGRAMMES F Heavy soil Crockery cutlery Prewash a pots and pans Wash 70 C n Rinses Dry CP Normal soil Crockery and cutlery Prewash Wash 65 C Dry Ci 5 Fresh soil Crockery and cutlery Wash 60 C nt 1 Rinse ECO Normal soil Crockery and cutlery Prewash Wash 50 C Rinses Dry AH Use this programme to quickly rinse the Rinse ri dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this pro gramme 1 With this programme you can wash a load with fresh soil It gives good washing results in a short time 2 This is the standard programme for test institutes With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil Refer to the supplied leaflet for test information Consumption values Programme time mi Energy kWh Water litre nute 110 120 184 7 18 20 Qu 100 110 1 4 1 5 18 20 Qu A r 30 0 8 8 ECO 120 130 OSE Og 12 13 QUIL DZ alia 0 01 5 The water pressure and
Download Pdf Manuals
Related Search