Electrolux EI24BC10QS Owner's Guide
Contents
1. sibs Interior Cleaning sarcinis an iaa EN NA arello E aleros iare A A Before You Call for Service i If Service IS Require aisis iriaren aiaia iaaiiai ihain Warranty IMformation es cccsccccceczccccssncsecancicesesstccseccncesdsecessticresctners 18 3 4 Safety Important Safety Instructions Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Danger Warning or Caution based on the risk type Definitions This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death AN DANGER DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury AN WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury AN CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury J IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related General Precautions AN WARNING RISK OF CHILD ENTRAPMENT Before you throw away your old appliance take off the doors and leave shelves in place so that children may not easily clim2. Alarm s will not e Door is ajar e Press Power key to shut off acknowledge alarm e Power has failed e Ensure door is closed firmly e Internal temperature is Allow 24 hours for temperature too high to stabilize Power is not e Circuit breaker has e Verify electrical supply See restored after tripped Installation section power failure Door does not e Door hinges are e Loosen hinges and re align close properly misaligned door Retighten hinges e Door gasket is not e Turn gasket 180 sealing properly 18 Warranty Information Major Appliance Warranty Information Your appliance is covered by a one year limited warranty For one year from your original date of purchase Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions In addition the cabinet liner and sealed refrigeration system compressor condenser evaporator dryer or tubing of your appliance is covered by a two through five year limited warranty During the 2 through 5 years from your original date of purchase Electrolux will repair or replace any parts in the cabinet liner and sealed refrigeration system which prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions Exclusions
3. DRAWERS CAN TIP INJURY COULD RESULT INSTALL ANTI TIP BRACKET PACKED WITH UNIT SEE INSTRUCTIONS Floor Mount Installation The anti tip bracket is to be located on the floor in the left or right rear corner of the beverage center as shown in Figure 6 Step by step instructions for locating the position of the bracket 1 Decide where you want to place the beverage center Slide it into place being careful not to damage the floor leaving 1 2 5cm of clearance from the rear wall to allow room for the anti tip bracket 2 Raise the rear leveling legs approximately 14 6mm to allow engagement with the anti tip bracket Level the unit by adjusting all the leveling legs as required Turning the leveling leg counterclockwise will raise the unit and clockwise will lower the unit 3 Make sure the beverage center is in the desired location then mark on the floor the rear and side corner of the cabinet where the anti tip bracket will be installed If the Figure 7 21 1 2 54 6cm installation does not allow marking the rear corner of the cabinet then make temporary lines on the floor marking the front corner of the cabinet excluding the drawer Slide the beverage center out of the way From the temporary line extend the sidewall line back 21 2 54 6cm as shown in Figure 7 4 Align the anti tip bracket to the marks on the floor so the side of the bracket lines up with the side of the cabinet mark and the
4. V notches on the anti tip bracket line up with the end of the 21 54 6cm line Rear of cabinet line 5 Fasten the anti tip bracket to the floor using the supplied screw See Figure 7 6 Slide the cabinet back into position making sure the rear cabinet leveling leg slides under the anti tip bracket engaging the slot Anti Tip Bracket FEG Leveling Leg Bottom View of Beverage Center AN WARNING TIP OVER HAZARD One of the rear cabinet leveling legs must be engaged under an anti tip bracket V notches in bracket Figure 7a V notches in bracket 8 Leveling Leveling the Unit Position the unit on a flat level surface capable of supporting the entire weight of the unit when full Leveling Legs Adjustable legs at the front and rear corners of the appliance should be set so the unit is firmly positioned on the floor and level from side to side and front to back The overall height of your Electrolux appliance may be adjusted between the minimum 33 34 85 7cm by turning the leveling leg in and the maximum 34 94 88 3cm by turning the leveling leg out See Figure 2 and 2a To adjust the leveling legs place the appliance on a solid surface and protect the floor beneath the legs to avoid scratching the floor With the assistance of another person lean the appliance back to access the front leveling legs Raise or lower the legs to the required dimension by
5. for future reference Should any problems occur refer to the Troubleshooting section of this manual This information will help you quickly identify a problem and get it remedied In the event you require assistance please contact the dealer where you purchased your unit Make a Record for Quick Reference Whenever you call to request information or service you will need to know your model number and serial number You can find this information on the serial plate located in the top left hand corner of your unit and on the product registration card Product Registration Card The package containing this manual also includes your product registration information Warranty coverage begins at the time your Electrolux beverage center was purchased AN NOTE Registering your product with Electrolux enhances our ability to serve you You can register online at www electroluxappliances com or by dropping your Product Registration Card in the mail Complete and mail the Product Registration Card as soon as possible to validate the registration date Please record the purchase date of your Electrolux unit and your dealer s name address and telephone number Purchase Date Electrolux Model Number Electrolux Serial Number Dealer Name Dealer Address Dealer Telephone Keep this manual and the sales receipt together in a safe place for further reference Questions For toll free
6. required If service is performed it is in your best interest to obtain and keep all receipts Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below This warranty only applies in the USA Puerto Rico and Canada In the USA and Puerto Rico your appliance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as described or illustrated are subject to change without notice NOOR WO N 13 14 USA 1 877 435 3287 Electrolux Major Appliances North America 10200 David Taylor Drive Charlotte NC 282 62 Canada 1 800 265 8352 Electrolux Canada Corp 5855 Terry Fox Way Mississauga Ontario Canada L5V 3E4
7. the Temp indicator will flash and an audible tone will sound every 60 seconds Additionally an ALARM RESET indicator will be displayed below the On Off keypad This alarm condition can be reset by momentarily pressing the On Off keypad If this alarm occurs it is recommended that you check the condition of your stored contents even though the appliance is operating normally and the temperature has recovered Prolonged temperature excursions could spoil perishables NOTE Multiple alarms are possible i e Door Ajar for a prolonged period may trigger a Temp alarm in which case both Door Ajar and Temp indicators will activate Door Ajar Temp NOTE The system status OK indicator blue dot at top of alarm window will remain lit whenever the unit is operating properly 12 Operation on off Air Filter alarm reset Air Filter The control will notify you as to when it is time to replace the air filter every six months The System Status indicator will turn off and the Air Filter indicator will flash Additionally an ALARM RESET indicator will be displayed below the ON OFF keypad No audible tone will sound The air filter condition can be reset by momentarily pressing the ON OFF keypad and the alarm will then display after another six months Vacation Sabbath mode This operating mode can be used to save energy during high cost energy period
8. turning the legs Repeat this process for the rear by tilting the appliance forward using caution On a level surface check the appliance for levelness and adjust accordingly Figure 2 Front Grille keep this area open Leveling legs 2 at the front and 2 in the rear Operation Temp Temp System Minus rapi Plus Display Area lait d Status Keypad yp Keypad yp Indicators Figure 8 Electronic Control Display Power Failure on off alarm reset Starting your appliance Plug the appliance power cord into a 115 volt wall outlet Your appliance is shipped from the factory in the On position and will begin start up of cooling as soon as power is supplied If the appliance does not start confirm that the wall outlet has power and that the control is in the On position See Turning your appliance On and Off The control display is covered with a clear plastic film This film may be removed by carefully lifting the film at a corner On initial power up the control display will indicate a Power Failure alarm This is anormal condition as the appliance was powered up at the factory for quality inspection and then removed from power A momentary press of the On Off keypad will reset this alarm condition See Alarms section Sleep mode If no keypads are pressed for 60 seconds the display will enter sleep mode to conserve power The contro panel w
9. FQ ricci EN B FR CENTRE DE BOISSONS ES CENTRO DE BEBIDAS EVERAGE CENTER USE AND CARE GUIDE GUIDE D UTILISATION ET D ENTRETIEN GUIA DE USO Y CUIDADO 242332700 June 2014 2 Finding Information Please Read and Save This Guide Thank you for choosing Electrolux the new premium brand in home appliances This Use amp Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new beverage center We view your purchase as the beginning of a relationship To ensure our ability to continue serving you please use this page to record key product information IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit All beverage centers require a connection to an electrical power source Improper hook up can result in a safety hazard and potential damage to the product or contents Proper installation in accordance with the manufacturer s specifications and all local codes is the sole responsibility of the consumer The manufacturer is not responsible for any installation expenses or damages incurred due to improper installation If you are unsure of your ability to safely connect electric power to the unit consult a licensed and insured professional to perform all electrical work Once you have your unit installed we suggest you keep this manual in a safe place
10. Remove Toe Grille Loosen don t remove these two screws If Service is Required e If the product is within the first year warranty period please contact your dealer or call Electrolux Customer Service at 877 435 3287 for directions on how to obtain warranty coverage in your area e If the product is outside the first year warranty period Electrolux Customer Service can provide recommendations of service centers in your area e In all correspondence regarding service be sure to give the model number serial number and proof of purchase e Try to have information or description of nature of the problem how long the appliance has been running the room temperature and any additional information that may be helpful in quickly solving the problem Door should be parallel to top and sides of the appliance Door adjustment bracket Figure 15a Troubleshooting 17 Before You Call for Service If Service is Required If the unit appears to be malfunctioning Contact the dealer where you purchased read through this manual first If the problem the unit if service is required State the persists check the Troubleshooting Guide model and serial number and explain the below Locate the problem in the guide and problem The model and serial number refer to the cause and its remedy before calling plate is located on the ceiling of your unit for service The problem may be something If you do not know
11. Stainless Steel Model e Your stainless steel model may discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless unit looking new by cleaning with a high quality all in one stainless steel cleaner polish on a monthly basis Frequent cleaning will remove surface contamination that could lead to rust Some installations will require cleaning on a weekly basis e DO NOT CLEAN WITH STEEL WOOL PADS e DO NOT USE CLEANERS THAT ARE NOT SPECIFICALLY INTENDED FOR STAINLESS STEEL this includes glass tile and counter cleansers e f any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with a high quality all in one stainless steel cleaner polish to prevent further problems e USE OF ABRASIVE PADS SUCH AS SCOTCHBRITE WILL CAUSE THE GRAINING IN THE STAINLESS TO BECOME BLURRED e Rust that is allowed to linger can penetrate into the surface of the stainless steel and become impossible to remove N CAUTION e Stainless steel models exposed to chlorine gas and moisture such as areas with spas or swimming pools may have some discoloration of the stainless steel Discoloration from chlorine gas is normal Follow exterior cleaning instructions e NEVER USE CHLORIDE OR CLEANERS CONTAINING BLEACH TO CLEAN STAINLESS STEEL Interio
12. This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined Product that has been transferred from its original owner to another party or removed outside the USA or Canada Rust on the interior or exterior of the unit Products purchased as is are not covered by this warranty Food loss due to any refrigerator or freezer failures Products used in a commercial setting Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in ordinary household use or used other than in accordance with the provided instructions Senice calls to correct the installation of your appliance or to instruct you how to use your appliance Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory 10 Service calls to repair or replace appliance light bulbs air filters water filters other consumables or knobs handles or other cosmetic parts 11 Pickup and delivery costs your appliance is designed to be repaired in the home 12 Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska Damages to the finish of appliance or
13. b inside A WARNING Never attempt to repair or perform maintenance on the unit until the electricity has been disconnected e Altering cutting of power cord removal of power cord removal of power plug or direct wiring can cause serious injury fire and or loss of property and or life and will void the warranty e Do not lift unit by door handle AN CAUTION Use care when moving the unit Some edges are sharp and may cause personal injury Wear gloves when moving or repositioning the unit e Never install the unit behind closed doors Be sure front grille is free of obstruction Obstructing free air flow can cause the unit to malfunction and may void the warranty e Allow unit temperature to stabilize for 24 hours before use N CAUTION e Use only genuine Electrolux replacement parts Imitation parts can damage the unit and may void the warranty Installation 5 Installing the Beverage Center Your Electrolux beverage center has been designed for either free standing or built in installation When built in your beverage center does not require additional air space for top sides or rear In either case the front grille must NOT be obstructed NOTE To ease unit installation and removal it is recommended that the cabinet rough opening dimensions be increased by at least 1 4 inch over the dimensions given for your unit NOTE All units require zero clearance when installed flush with a cabi
14. home incurred during transportation or installation including but not limited to floors cabinets walls etc Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes such as abuse misuse inadequate power supply accidents fires or acts of God DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If You Need Service Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period should service be
15. ill go dark with the exception of the system status OK indicator which will remain enabled Alarm conditions will wake the display see Alarms section To make the following changes to the control settings turning the appliance ON OFF adjusting the temperature changing the interior lights and activating vacation mode the control must be awake To wake the display press any keypad A confirm tone will sound and the current storage compartment temperature will be displayed aem EmN lock EH E The sleep mode can be disabled if you prefer to have the display on continuously Press and hold the Lock keypad until the display goes past Loc and reads nSL To enable the sleep mode repeat the instruction again going past Loc until the display reads SLP q at th on off Turning your appliance ON and OFF If the appliance is On and out of sleep mode the temperature will be shown in the display area of the control To turn the appliance Off press and hold the On Off keypad for four seconds OFF will now be displayed on the control on off To turn the appliance On press and hold the On Off keypad for four seconds 10 Operation BE Adjusting the temperature To set or check the set point temperature with the control out of sleep mode press the or keypads SET will be indicated on the user interface panel and the current set point temperature will disp
16. l operation press and hold the On Off keypad until the control displays the temperature Storage 13 Proper Storage Figure 12 Display Rack The bottom rack in your beverage center is designed for storage as well as for display purposes The unit holds five standard size wine bottles in the display rack Stocking Recommendations The two sliding glass shelves can easily be converted to wine storage by removing the glass panels The wine racks allow for the proper horizontal storage of wine The bottles are properly positioned so that the wine remains in contact with the cork to assure that the cork does not become dry White and sparkling wines should be maintained on the bottom to middle racks and red wine on the top racks Your beverage center should be stocked beginning with the bottom display rack at the back and working forward staggering Glass the bottles Subsequent racks should be stocked similarly starting with the back of each rack Figure 11 Loading Tips and Suggestions Your appliance is equipped with a cantilever shelf system which provides maximum adjustability and customization of the shelving arrangement Wine cutout and Wine shelf flat glass shelf underneath with vibration glass dampening mat Beverage Center Shelving 1 half width frame and glass shelf 2 wine frame and flat glass roll out shelves 1 five bottle roll out wine display rack Figure 9 Figure 10 Half wid
17. lay and flash Subsequent presses of the or keypads will adjust the temperature colder or warmer respectively When you have reached your desired set point temperature press the On Off keypad to accept or do nothing and the Set mode will time out in 10 seconds accepting the displayed temperature as the new set point The available set point temperature range for your appliance is 34 F 1 1 C to 42 F 5 6 C If you attempt to adjust the temperature outside of this range you will receive an audible notification When initially loading your product with warm contents it may take up to 48 hours for the storage compartment temperature to stabilize When making temperature set point changes it may take up to 24 hours for the stored contents to stabilize at your new set point temperature Factors that affect the storage compartment stabilized temperature e Changes to temperature setting e Room temperature changes e Temperature of stored contents Loading warm contents Cold content load will delay the change to a warmer set point temperature Warm content load will delay the change to a colder set point temperature e Usage number and duration of the door openings e Use of the storage compartment display lighting glass door product only e Installation of the appliance in direct sunlight or next to a heat source Interior display lighting Glass door models only You
18. net or wall Electrolux stainless steel models require a minimum 2 inch handle clearance when installed against a wall or cabinet that extends beyond the front edge of the unit Unit Dimensions 23 7 s inch 33 3 4 34 3 4 inches 26 3 s inch i 46 13 32 ASE 21 2 sy es Yt W Top 23 7 8 T i 26 3 8 23 23 32 1 1 l 21 1 2 paoi l i if n 33 3 4 Adjustabe to 34 3 4 2 34 S ts sne Installation Site Preparation 1 Position the unit on a flat level surface capable of supporting the entire weight of the unit Remember the unit will be significantly heavier once it is fully loaded 2 This unit requires a grounded and polarized 115 VAC 6O0HZz 15A circuit normal household current 3 Avoid connecting the unit to a Ground Fault Interrupter GFI GFls are prone to nuisance tripping which will cause the unit to shut down GFls are generally not used on circuits which power equipment that must run unattended for long periods of time 4 The unit must be installed according to your state and local laws and regulations AN WARNING ELECTROCUTION HAZARD Electrical Grounding Required This appliance is equipped with a three prong grounding polarized plug for your protection against possible shock hazards e NEVER remove the round grounding prong from the plug e NEVER use a two prong grounding adapter e NEVER use an extension cord to co
19. nnect power to the unit Where a two prong wall receptacle is encountered or a longer power cord is required contact a qualified electrician to have it replaced in accordance with applicable electrical codes 5 Position the unit to allow free air flow through the front grille Intake Exhaust 6 Wipe out inside of unit with a damp cloth 7 Be sure to install the Anti Tip bracket Follow the instructions provided with the Anti Tip bracket kit Installing the Anti Tip Device AN WARNING Do not double stack two units as shown below This may cause serious personal injury If your beverage center is not located under a counter top free standing you must use an anti tip device installed as per these instructions If the beverage center is removed from its location for any reason make sure that the device is properly engaged when you push the beverage center back into the original location If the device is not properly engaged there is a risk of the beverage center tipping over causing property or personal injury if you or a child stand sit or lean on an open shelf NOTE If installing on a concrete floor concrete fasteners are required not included with the anti tip kit Installation 7 N CAUTION Any finished flooring should be protected with appropriate material to avoid damage when moving the unit A WARNING ALL
20. r Cleaning as Required 1 Disconnect power to the beverage center 2 Remove racks if desired see WINE RACK REMOVAL INSTALLATION 3 Wipe down the interior with a solution of non abrasive mild detergent and warm water 4 Rinse with clear water 5 Reconnect power to the unit Air Filter Remove plastic wrap and install the static air filter located in the literature pack in the air filter housing attached to the ceiling of your unit Ordering replacement filters Order new filters by calling toll free 1 877 808 4195 visiting www electroluxappliances com or seeing the dealer where you bought your beverage center Electrolux recommends that you order extra filters when you first install your beverage center and that you replace your filters at least once every six months Here is the product number to request when ordering PureAdvantage Air Filter Part EAFCBF 16 Maintenance Door Alignment The door should be parallel to the sides and top of the appliance If alignment is necessary the door may be adjusted by removing the grille then loosening the 2 screws which secure the door adjustment bracket on the bottom of the door see Figure 15a and adjusting the door side to side Use a 532 allen wrench for this procedure See Figure 15 below When finished aligning the door tighten the screws securely and install the grille Figure 15
21. r appliance is equipped with a dual ight level display lighting feature With the control out of sleep mode press the Light keypad once to activate the interior ighting display feature at full illumination A confirmation tone will sound and the ight bulb Icon will illuminate Pressing the Light keypad a 2nd time will dim the ighting to 50 A 3rd press will deactivate the display lighting feature The display ighting will automatically deactivate after our hours T A Tii Ele Z IT Temperature mode The temperature mode is preset from the factory in Fahrenheit F but you have the option to change it to Centigrade C To change the mode press and hold the keypad while pressing the keypad then release the keypad The temperature will now be displayed in Centigrade C Repeat the procedure to change the temperature mode back to Fahrenheit F lock Control lock The control panel can be locked to avoid unintentional changes To lock the control press and hold the Lock keypad until the display reads Loc The lock icon will flash three times and then continuously illuminate When the control panel is locked only the Lock keypad System Status OK indicator and the Alarm indicator are active To unlock the control panel repeat this instruction until the display reads nLc Operation 11 Alarms The control will alert you to conditions that could adversely affect the pe
22. rformance of the appliance Door Ajar on off alarm reset Door ajar If the door is open or not closed properly for more than five minutes the System Status OK indicator will turn off the Door Ajar indicator will flash and a tone will sound every 60 seconds Additionally an ALARM RESET indicator will be displayed below the On Off keypad This alarm condition can be reset by closing the door or momentarily pressing the On Off keypad i e if you are cleaning the storage compartment etc The alarm will recur in five minutes if the alarm condition persists Power Failure on off alarm reset Power failure If power to the appliance is interrupted the System Status indicator will turn off and the Power Failure indicator will flash Additionally an ALARM RESET indicator will be displayed below he On Off keypad No audible tone will sound This alarm condition can be reset by momentarily pressing the On Off keypad If this alarm occurs it is recommended that you check the condition of any perishables even if the appliance is operating normally and the temperature has recovered Prolonged power outages could result in excessive temperature excursions which may spoil perishables on off alarm reset Temperature alarm If the storage compartment temperature exceeds 10 F from set point for more than a one hour duration the System Status indicator will turn off
23. s or when you won t be using your appliance for an extended period of time Vacation mode also serves as a Sabbath mode disabling functions and its controls in accordance with the weekly Sabbath and religious holidays observed within the Orthodox Jewish community When used as Sabbath mode you may open or close the door at any time to access contents without concern of directly turning on or off any lights digital readouts solenoids fans valves compressor icons tones or alarms When activated the display alarm indicators and tones keypad touch tones interior lights and all options are disabled All keypad functions are disabled with the exception of the On Off keypad which is required to exit X Vacation Sabbath mode Storage compartment temperatures are monitored and controlled at the settings prior to entering Vacation Sabbath mode For further assistance guidelines for proper usage and a complete list of models with the Sabbath feature please visit the web at http www star k org To enter Vacation Sabbath Mode with the control out of sleep mode press and hold the On Off keypad until the display goes past OFF and reads VAC The display will flash VAC three times to acknowledge your request then will display VAC continuously until Vacation Sabbath mode is exited A power outage will not exit Vacation Sabbath mode exiting can only be accomplished manually To exit Vacation Sabbath mode and return to norma
24. telephone support in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 For online support and Internet product information www electroluxappliances com Finding Information Table of Contents Finding ITONIMATION ies eearri eenas Saks ces see eee eee aac cakstessteeteescxerse 2 Please Read and Save This Guide i Make a Record for Quick Reference eeeeieeeeeseeeeteeeeeeeteeeeeeee 2 Product Registration Card iis scisn nencsidecie dave wade 2 QUESTIONS alkisch inaia nanea Ka AERAR aa pi 2 SAVY idas i aaaea ranea Eoi r daa aaan daaa aas 4 Important Safety MNStrUCoN Sesioni 4 Safety PreCAautlONS eosin yeso doe iao a a EE 4 Definitions General Precautions Installati n cecsccicsetescccnscarsasccsensensscsscscacanselsessaesnssavsarsatecvetisansensaates 5 Installing the Beverage Center ssssssssssssesserrsrssrssrsernrrssrnsrnsrnernnns 5 Site Preparation cecceccceees Installing the Anti Tip Bracket LOVE Pr E 8 Leveling ihe UNIT iesi niini erano asiwa a 8 Oro e E E E A T a E A ena Temperature Mode IANS erena aE E LE S A acne Vacation Sabbath MOJE sinirinin n aai 12 Stol e 0 eE A A S Proper Storage zisk Shelving Installation Removal sssssssisssssssssssisrsssssssrserssrrsenssnens 14 Maintenance cicscetcesscivsctsascivenscusscucsarsansevcasencsnesavearsasseventesnscvesen Maintaining Your Beverage Center cccceeeeeeeee Exterior Cleaning for Your Stainless Steel Model
25. th frame and glass shelf 14 Storage N CAUTION Make sure your cantilever shelf is secure on the shelf supports by pressing down on the shelf before loading the shelf To Add or Remove a Shelf Remove stored product from the shelf Do not try to remove a loaded shelf from the appliance Grasp the shelf front with both hands rotate the front upward and lift out See Figure 13b To install a shelf insert the shelf in the appliance and insert the hooks into the shelf support slots and drop the shelf down so the tabs engage the bottom of the slots ont support Figure 14 To remove the wine shelf from the frame Extend the wine shelf from the frame until Figure 13a it stops Lift the front of the shelf to Tall bottle storage area Grasp the shelf by the front w both hands and rotate the front of the shelf up then lift the shelf up and remove the shelf from the shelf ladders N CAUTION Never try to move a loaded shelf remove everything from the shelf before moving Use both hands when moving the shelf disengage the side rails and remove the shelf Maintenance 15 Maintaining Your Beverage Center Periodic cleaning and proper maintenance will ensure efficiency top performance and long life The maintenance intervals listed are based on normal conditions You may want to shorten the intervals if you have pets or other special considerations Exterior Cleaning for Your
26. the name of the selling dealer very simple that can be solved without a or a local service company you can check service call Consulting or contracting a online at www electroluxappliances com or qualified service technician may be necessary call 1 877 435 3287 Z WARNING ELECTROCUTION HAZARD NEVER attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected Possible Cause Unit not cold e Control set too warm e Adjust temperature colder Allow 24 enough hours for temperature to stabilize Adjust e Light staying on e Turn off manual light control temperatures See Operation section see Adjusting e Airflow to front grille e Airflow must not be the Temperature blocked obstructed to front grille See M Installation section Con roF section e Door gasket not e Adjust door gasket sealing properly Unit too cold Control set too cold e Adjust temperature warmer Contents of unit Allow 24 hours for temperature too cold frozen to stabilize just temperatures Adjusting the Temperature in the Start Up and Temperature Control section No interior light e Failed LED assembly e Contact a qualified Electrolux Service Technician Light will not go e Manual light control e Turn off manual light control out when door is is ON See Operation section closed e Door switch not e Check for proper door making contact alignment
Download Pdf Manuals
Related Search