Edelbrock 2010 User's Manual
Contents
1. 19 Disconnect the Manifold Air Presse sensor and EVAP solenoid electrical connectors 20 Use a 3 8 Fuel Line Removal Tool to disconnect the fuel line from the fuel rails and from the passenger side fender fitting Use a shop rag to absorb any excess fuel 21 Use a 10mm socket to remove the nut down the fuel line clamp then remove the fuel line and clamp Brochure 763 1598 Rev 2 11 AJ mc SUPERCHARGERS BY 22 Disconnect the two ignition harness connectors the eight spark plug wires from the ignition coils and the eight fuel Injector electrical connectors 23 Use a 10mm deep socket to remove the five studs retaining each of the ignition coil brackets to the valve covers Lift and remove the coil brackets as an assembly 24 Disconnect the EVAP hose from the EVAP Solenoid and the side fender fitting 25 Use a 10mm socket to remove the nut on the driver side ane remove the plastic manifold webbing 26 Use an 8mm socket to remove the manifold bolt on the driver side retaining the fuel rail bracket 2011 Edelbrock LLC Part 41596 1597 1598 amp 1599 Page 9 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 2 Use a 10mm deep socket to remove the four fuel rail studs Remove the fuel rail bracket then remove the rails by lifting the injectors straight up out of their provisions then work the rails forward and set them aside2. Edelbrock 2010 Camaro SS Supercharger Part 1596 1597 1598 amp 1599 Edelbrock Edelbrock E Force Supercharger System for P e4 5 the 2010 Camaro SS SUPERCHARGERS BY Installation Instructions INTRODUCTION Thank you for purchasing the Edelbrock 6 2L GM Supercharger System for the 2010 Chevy Camaro The Edelbrock E Force Supercharger System for the 2010 Camaro SS utilizes Eaton s new Gen VI TVS Supercharger rotors featuring a four lobe design with a full 160 deg of twist for maximum flow minimum temperature rise quiet operation and the reliability for which Eaton is known The Edelbrock Supercharger is a complete system that maximizes efficiency and performance by minimizing air restriction into and out of the supercharger This results in maximum airflow with minimal temperature rise and power consumption The supercharger housing itself is integrated into the intake manifold for a seamless design with minimal components eliminating the possibility of vacuum leaks between gasket surfaces The system also utilizes a front drive front inlet configuration giving it the shortest least restrictive inlet path on the market The supercharger is inverted expelling the air upward Air pressure then builds in the plenum before being drawn down through each of two intercooler cores oriented horizontally next to and below the supercharger outlet After passing through the intercooler cores the air travels through
3. Brochure 763 1598 Rev 2 11 AJ mc Edelbrock SUPERCHARGERS BY Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions Additional Supporting Components Now that the horsepower potential of your Camaro has been substantially increased Edelbrock strongly recommends upgrading the suspension exhaust and braking systems in order to fully utilize these gains The following components have been designed specifically to enhance the handling and acceleration capabilities of your Camaro when used in conjunction with the E Force Supercharger Suspension Components Lo Ae D RB 2 B Front Sway Bars are manufactured from lightweight hollow core 4130 Chromoly steel for maximum strength and durability The CNC forming ensures precision fitment for a true bolt on installation A gloss black powder coated finish is applied for great looks lasting durability and corrosion resistance They also include greasable graphite polyurethane bushings and high quality zinc plated hardware Front Sway Bar rre 52813 Complete Sway Bar Set Heavy duty Adjustable Trailing Arms allow suspension adjustments for optimum handling and traction They can be adjusted without removing the arms from the vehicle oimply loosen the jam nuts and adjust pinion angle opherical ball assembly with Delrin bushings allows rear suspension to move more fre
4. Compressed Air e Masking Tape Torx 20 Driver J 42386 A Flywheel Holding Tool e Allen Wrenches including 6mm 8mm e Soldering Iron Edelbrock LLC 2700 California Street Torrance CA 90503 Toll Free Tech Line 1 800 416 8628 Office Sales Line 310 781 2222 2011 Edelbrock LLC Brochure 763 1598 Part 1596 1597 1598 amp 1599 Page 1 Rev 2 11 AJ mc Edelbrock Edelbrock E Force Supercharger System for oT 6 3 the 2010 Camaro SS SUPERCHARGERS BY Installation Instructions Proper installation is the responsibility of the installer Improper installation will void warranty and may result in poor performance and engine or vehicle damage Due to the complexity of the Edelbrock E Force Supercharging system it is recommended that this system only be installed by a qualified professional with access to a service lift pneumatic tools and a strong familiarity with automotive service procedures To qualify for the optional warranty it is necessary to have this system installed by a certified ASE technician GM dealership or Edelbrock approved installer Failure to have this system installed by a properly certified service center may result in voiding of the optional warranty offered with this sytem Please contact the Edelbrock Technical Support department if you have any questions regarding how this sytem and or your installer of choice will affect any warranty coverage for which your vehicle may qualify Any
5. _ the PCV tube from the cover 30 Use an 8mm socket to remove the nine remaining manifold bolts Note that the rearmost passenger side bolt will come out with the manifold and that it is necessary to rotate the manifold towards the passenger side to remove the rearmost driver side bolt and the bracket it retains 31 Reach behind the manifold from the driver side to lift the gray tab and depress the black tab to disconnect the oil pressure sensor electrical connector Brochure 63 1598 Rev 2 11 AJ mc 220074 FORCE SUPERCHARGERS BY 32 Use a pair of hose clamp pliers to loosen the clamp retaining the vacuum hose to the brake booster fitting and disconnect the hose It will be removed with the manifold 33 Lift the rear of the manifold over the oil pressure sensor and pull it forward to remove it Remove the o ring seals from the manifold flanges and retain them for later reuse 34 Use a clean shop rag to wipe down the intake flange of both cylinder heads then put a small strip of masking tape over each port to prevent debris from entering 35 Use a crescent wrench to remove the oil pressure sensor from the engine valley plate NOTE Steps 36 42 outline the procedure for disabling the Active Fuel Management system found in Camaros equipped with an automatic transmission Manual vehicles should skip ahead to step 43 WARNING AUTOMATIC CAMAROS EQUIPPED W
6. full depth of the hole Brochure 763 1598 Rev 2 11 AJ mc SUPERCHARGERS BY 4101 79 Use compressed air to clean out any metal flakes then loosen the bolt and remove the drill guide 80 Apply red Loctite retaining compound to the supplied crank pin and tap it into the reamed hole until it is flush with the crank snout 81 Install the crank bolt supplied in Bag 4 and torque it to 37 ft lbs then rotate it an additional 140 82 Remove GM Flywheel Holding Tool J 42386 A 83 Lift the starter support bracket and starter into place then use a 13mm wrench to reinstall the power wire onto the starter 84 Reconnect the starter solenoid electrical connector 85 Use an 8mm wrench to reinstall the three bolts that hold the starter heat shield in place 86 Use a 13mm socket to install the two starter bolts 87 Use a 10mm socket to reinstall the starter support bracket bolt 88 Lower the fan assembly back into place reconnect the passenger side electrical connector then use a 13mm socket to reinstall the stock fan assembly bolt on the driver side only the passenger side will be installed later 89 Use a panel puller to remove the two body pins from the top of the lower radiator shroud u 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 14 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 90 Install the supplied heat exchanger behind the bum
7. loads and which use an eccentric for rear toe adjustment that is susceptible to slippage The Heim joint on the Edelbrock Toe Links allow the suspension to operate smoothly throughout its full range of motion The kit includes lockouts for the eccentrics to stop any movement of the rear toe adjustment and relocates the adjustment point onto the toe link for a finer and easier adjustment Adjustable Rear 52801 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 24 Brochure 63 1598 Rev 2 11 AJ mc
8. previously installed aflermarket tuning equipment must be removed and the vehicle returned to an as stock condition before installing the supercharger Any equipment that directly modifies the fuel mixture or ignition timing of the engine can cause severe engine damage if used in conjunction with the Edelbrock E Force Supercharger System This includes but is not limited to ignition boxes air fuel controllers OBDII programmers and any other device that modifies signals to and or from the ECU Aftermarket bolt on equipment such as underdrive pulleys or air intake kits will also conflict with the operation of the supercharger and must be removed prior to installation Use of any of these products with the E Force Supercharger could result in severe engine damage 91 octane or higher gasoline is required at all times If your vehicle has been filled with anything less it must be run until dry and refilled with 91 or higher octane gasoline twice prior to installation Inspect all components for damage that may have occured in transit before beginning installation If any parts are missing or damaged contact Edelbrock Technical Support not your parts distributor Edelbrock periodically releases improved versions of the calibration file found on the supplied handheld programmer Check the website to ensure you have the latest version as described in step 165 2011 Edelbrock LLC Brochure 763 1598 Part 1596 1597 1598 amp 1599 Page 2
9. socket to install the supplied tensioner bracket to the water pump ARV 59 Apply blue Loctite to the threads of the M10 x 65mm bolt supplied in Bag 1 then use an 8mm allen to install it in the countersunk bolt hole of the tensioner bracket 60 Apply blue Loctite to the threads of an M8 x 20mm bolt supplied in Bag 1 then use the supplied washer and a 12mm socket to install the supplied idler pulley onto the tensioner MT 61 Apply blue Loctite to the threads of the M10 x 65mm bolt supplied in Bag 1 then use a 15mm socket to install the tensioner onto the tensioner bracket 62 Use a 12mm socket and an M8 x 20mm bolt supplied in Bag 1 to secure the ground strap to the back side of the tensioner bracket Brochure 763 1598 Rev 2 11 AJ mc SUPERCHARGERS BY 63 Use pliers to loosen the hose clamps and disconnect the two small upper radiator hoses Use caution when removing and reinstalling hoses onto plastic fittings r y 64 Use a 13mm socket to remove the two bolts holding the fan assembly to the top of the radiator then disconnect the electrical connector on the passenger side of the fan assembly and remove the radiator fans 65 Disconnect the oil level sensor electrical connector from the passenger side of the oil pan 66 Use a 10mm socket to remove the starter support bracket bolt 67 Use a 13mm socket to remove the two starter bolts 68 Use an 8mm wrench t
10. the long 12 individual intake runners which route underneath the supercharger housing to the cylinder head ports in a horizontal nested configuration The upper plenum area is enclosed by a top cover that has been designed to provide an appealing and distinctive under hood appearance This configuration allows for a compact package that can fit under the stock hood and cowl of the Camaro without sacrificing runner length or intercooler area The E Force supercharger features a uniquely styled plenum and includes matching side covers The Edelbrock supercharger provides neck snapping performance that is safe to operate on a completely stock engine It is 50 state emissions legal and can be had with an optional 5 year 100 000 mile warranty so that there are no worries when installing it on a brand new car TOOLS REQUIRED Jack and Jack Stands e 3 8 Fuel Line Removal Tool OR Service Lift Torque Wrench e Panel Puller Needle Nose Pliers e Ratchet and Socket Set including 7mm 8mm 10mm e Pliers standard deep and universal 12mm deep 13mm OR Hose Clamp Removal Tool 15mm deep 18mm 21mm deep 24mm e Pneumatic or Power Drill e Wrenches including 8mm 13mm 16mm 18mm e 1 1 8 or larger Uni bit 13 16 3 4 e Impact Wrench Crescent Wrench Red amp Blue Loctite or equivalent e 12 Ratchet Extension Bar O ring Lube 1 2 Breaker Bar Thread Sealing Compound e Flat Blade amp Philips Screwdrivers Anti sieze
11. 3 j ZI ey 1 47 er t aJ ES E b d E BnF 1 3 4 fa i 53 Install the supplied Heater Core Hose Assembly to the firewall fittings using the supplied hose clamps Route the lines between the engine oil dipstick and the fuse box to the fittings on the water pump and secure them with the supplied hose clamps Note that the hose closer to the passenger side of the firewall will be routed to the fitting Brochure 63 1598 Rev 2 11 AJ mc SUPERCHARGERS BY Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 54 Apply blue Loctite to the threads of the M8 x 20mm bolt supplied in Bag 1 then use a 12mm socket and washer to install the smaller supplied idler pulley onto the supplied idler bracket 55 Use a 10mm socket to remove the three water pump bolts Indicated 1 56 Apply blue Loctite to the threads of the M8 100mm bolts supplied in Bag 1 then use a 6mm Allen tool to install the idler the water pump 57 Use a 15mm socket to remove the nut retaining the ground strap on the passenger side cylinder head then use a 15mm deep socket to remove the ground strap stud rau ce 5255 quac ire 3 Sas a 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 12 58 Apply blue Loctite to the threads of the stock tensioner bolts then use a 15mm
12. 6 x 2 120mm Hex Bolt Drill Hole 1x 1 4 x 3 4 Steel Dowel 1x Crank Pinning Drill Guide 1x 15 64 High Speed Steel Drill Bit 1X 2500 Reamer 2011 Edelbrock LLC Brochure 63 1598 Part 1596 1597 1598 amp 1599 Page 4 Rev 2 11 AJ mc Edelbrock Edelbrock E Force Supercharger System for e4 5 the 2010 Camaro SS SUPERCHARGERS BY Installation Instructions 13 Coil C 4x Coil Cover Bracket Grommet X Coil Cover Dipstick Grommet 4x Coil Cover Bracket Ax Coil Cover Retainer Stud 4x Coil Cover Standoff 2011 Edelbrock LLC Brochure 63 1598 Part 1596 1597 1598 amp 1599 Page 5 Rev 2 11 AJ mc Edelbrock E Force Supercharger System for FORCE the 2010 Camaro SS SUPERCHARGERS BY Installation Instructions HOSE IDENTIFICATION GUIDE Intercooler Water Pump to Heat Exchanger Hose Heater Core Hose Assembly Fuel Rail Inlet m aa 1 1 Fuel Rail Crossover Intercooler Reservoir to Water Pump Hose Manifold to EVAP Solenoid Hose 18 EVAP Solenoid to Fender Fitting Hose 15 Brake Booster to Manifold Hose Passenger Side Driver Side PCV Hose 22 PCV Hose 247 Intercooler Hose Assembly Driver Side Manifold to Intercooler Reservoir Hose Passenger Side Manifold to Intercooler Reservoir Hose 2011 Edelbr
13. ITH STANDARD NON AFM LIFTERS MUST USE THE MANUAL VALLEY COVER PLATE FAILURE TO DO SO WILL RESULT IN ENGINE DAMAGE 36 Use a 13mm socket to remove the eleven bolts retaining the engine valley plate and remove the plate 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 10 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 37 Use a T 20 Torx driver to remove the four bolts retaining the plastic solenoid bracket then pry open the clip at the rear of the plate to remove the bracket d dm y 0 andr emove them 39 Use 30 Torx driver to remove the twenty bolts holding the steel sandwich in place and remove it 40 Remove the plastic and rubber gasket from the valley tray using great care not to damage the seal 41 Trim the two tabs projecting from the gasket to the base of their tapers Use a file to remove any burrs then install the gasket in the new valley plate 42 Install the new valley plate with the gasket in place onto the engine and proceed to step 47 43 Use a 13mm socket to remove the eleven bolts retaining the engine valley plate and remove the plate The metal and rubber gasket beneath it will be reused and should be left in place 44 Use a flathead screwdriver to remove the eight o ring seals from the underside of the valley plate 45 Inspect each seal for damage and replace any that have been co
14. Rev 2 11 AJ mc Edelbrock L AM EL UT Lan Edelbrock E Force Supercharger System for FO 1 05 the 2010 Camaro SS SUPERCHARGERS BY 440 Installation Instructions INSTALLATION HARDWARE IDENTIFICATION GUIDE Wd hene 1 M10 1 5 x 65mm Socket Head Bolt 3x M8 x 1 25 x 100mm Socket Head Bolt B LUAM 1 M10 x 1 5 x 65mm Hex Flange Bolt I 3x M8 x 1 25 x 20mm 2x M8 Washer Hex Flange Bolt x 4 M8 x 1 25 x 20mm 1x M6 x 1 x 25mm Hex Stand Off Hex Flange Bolt 2x 1 2 Hose Clamp ian 7x 3 4 Hose Clamp g 1x M8 x 1 25 x 30mm Hex Flange Bolt 2x Nylon Body Pin Ax M6 x 1 x 16mm Hex Flange Bolt 1 x Lower Intercooler Reservoir Bracket 4x M8 x 1 25 Hex Flange Nut 1x Upper Intercooler Reservoir Bracket 2011 Edelbrock LLC Brochure 63 1598 Part 1596 1597 1598 amp 1599 Page 3 Rev 2 11 AJ mc A PELA Edelbrock S Edelbrock E Force Supercharger System for e4 5 the 2010 Camaro SS SUPERCHARGERS BY Installation Instructions Bag 3 11x M8 x 1 25 x 25mm Countersunk Socket Head Bolt 8x M6 x 1 x 45mm Hex Flange Bolt 4x M6 x 1 x 12mm Socket Head Bolt Bag 4 1x GM Factory Harmonic Balancer Bolt D m C cs MP abi d 4 n ET aj 1 M1
15. argers fuel injected soft tech shtml to confirm that you have the latest calibration Once you have found the latest tune on the site power on the programmer press the left arrow and select the Device Info option scroll down to Tune Version and compare that number to the one on the site If they are different download the new calibration with the supplied USB cable 164 Turn the key to the On position but do not start it 165 Connect the PCM cable from the supplied downloader to the OBD II connector located below the steering wheel in the passenger compartment 166 Use the directional pad to highlight the Program Vehicle option and press the Select button 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 21 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 167 Use the directional pad to highlight the Preprogrammed Tune option and press the Select button 168 Read disclaimer then press Select to continue 169 Verify ignition is in the Key On position but that the engine is not running then press Select 170 Use directional pad to highlight your vehicle and transmission combination then press Select 171 Use directional pad to highlight your vehicle and transmission combination then press Select again 172 Use directional pad to highlight Begin Program then press Select 173 Vehicles equipped with a manual transmission will have three separate ope
16. body Push down on the cover until the tabs snap into place i 144 Use a flathead screwdriver to tighten the worm clamps on each end of the silicone tube 145 Connect the stock MAP amp MAF sensor wiring harness connectors into the supplied TMAP wiring harness then connect the TMAP harness to the MAF sensor 146 Use a 13mm socket to remove the nut from the power stud at the front of the fuse box Slide the ring connector at the end of the orange wire on the relay harness over is M reinstall the Stock nut Brochure 763 1598 Rev 2 11 AJ mc 3 Edelbrock E Force Supercharger System for FORCE the 2010 Camaro SS BY AG Installation Instructions 147 Install the relay on the tab on the passenger side of 152 Carefully route the Passenger Side PCV Hose to the the fuse box and the fuse housing on the brace directly in fitting on the underside of the silicone air inlet tube so as front of the fuse box using the body pins supplied in Bag 2 avoid contact with the r any pulleys 148 Route the intercooler water pump connector attached to the relay down to the water pump and plug it in 153 Use a 10mm deep socket to install the supplied ball studs into the new coil covers 149 Use a 10mm socket to remove the passenger side fender bolt install the ground strap ring connector underneath it then reinstall the bolt 150 Disconnect the stock EVAP solenoid electrical connect
17. e clamp supplied in Bag 2 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 15 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 99 Install the Intercooler Hose Assembly by sliding it down between the radiator fan assembly and the engine Note that the short hose section will go around the radiator to the outlet of the heat exchanger 100 Use a unibit to drill a 1 1 8 hole in the radiator shroud on the driver side directly across from the heat exchanger outlet 101 Slide the short section of the Intercooler Hose Assembly through the hole and onto the heat exchanger outlet Secure it with a 3 4 hose clamp supplied in Bag 2 102 Mount the brackets supplied in Bag 2 to the intercooler reservoir with the M6 x 16mm bolts supplied in Bag 2 as shown 7 lt lt Di Le 103 Use a 10mm socket to remove the upper outside nut on the back the passenger side of the radiator fan 104 Use a 13mm wrench to install the standoff stud supplied in Bag 2 to the upper outside stud on the back of the radiator fan on the passenger side Brochure 63 1598 Rev 2 11 AJ mc ae SUPERCHAR 105 Install the intercooler reservoir to water pump hose onto the outlet of the intercooler reservoir so that the other end will extend down to the inlet of the intercooler water pump Secure the hose to the reservoir f
18. ely Includes graphite polyurethane differential bushings to replace soft OE bushings Adjustable Tubular Lower Trailing Arm 5200 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 23 E c CR m e e Rear Sway Bars are manufactured from heavy duty solid core 1045 high strength steel for maximum durability The CNC forming ensures precision fitment for a true bolt on installation Edelbrock engineers have designed these to allow removal of the vehicle s rear differential cover with the sway bar fully installed They include greasable graphite polyurethane bushings on most applications u bolts and high quality zinc plated hardware Rear Sway Bar rrr 52814 52815 Direct bolt on Brake Hoses bring the ultimate in braking performance They improve your braking performance for competition or every day driving Replacing the OE rubber hose with Russell brake hose reduces hose expansion for more consistent braking Featuring stainless steel braided hose with zinc plated fittings these hoses are factory assembled for convenient installation and meet the U S Dept of Transportation FMVSS 571 106 requirements Brake Hose on 692380 Brochure 63 1598 Rev 2 11 AJ mc 222238 SUPERCHARGERS BY Edelbrock shorty headers have outstanding performance features such as mandrel bent tubes and laser cut
19. etaining the bottom of the fascia 9 Use a panel puller to remove the six body pins holding the top of the fascia then use a 10mm socket to remove the bolt at each end of the top of the fascia 10 The front fascia can now be pulled forward and off the car and set aside Brochure 763 1598 Rev 2 11 AJ mc SUPERCHARGERS 11 the Mass Airflow Sensor connector 12 Usea flat head screwdriver to loosen the worm clamp holding the inlet tube to the air box lid then remove the air box lid by pushing the lock tabs back 13 Remove the oil fill cap and remove the plastic engine cover Reinstall the oil fill cap 14 Disconnect passenger side PCV tube from the valve cover then use a flat head screwdriver to loosen the worm clamp retaining the air intake tube to the throttle body Remove and discard the air intake tube and PCV hose 15 Use a 15mm socket and a breaker bar to loosen the tensioner and remove the serpentine Dei 2 16 Disconnect the Electronic Throttle Control connector on the passenger side of the throttle body 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 8 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 17 Use a 10mm socket to remove the four bolts retaining the throttle body and set it aside 18 Push down the white tab on the front EVAP hose fittings and disconnect them from the manifold and the EVAP solenoid
20. for the 2010 Camaro SS Installation Instructions 120 Connect the supplied Fuel Rail Crossover line with the 90 fittings to the passenger side fuel rail then install the fuel rails by lining up the injectors with the provisions in the manifold and pushing them down until they are seated and the bolt holes in the rails line up with those in the supercharger Route the crossover line below the hub snout and air inlet of the supercharger and over to the front of the driver side rail as you are installing the passenger side rail 121 Install the supplied Fuel Rail Inlet between the fender fitting and fuel rail fitting on the passenger side 122 Clip the Fuel Rail Crossover line onto the driver side fuel rail fitting TES 123 Use a 5mm Allen tool to install the four M6 x 12mm fuel rail hold down bolts supplied in Bag 3 124 Install the supplied Brake Booster to Manifold Hose onto the brake booster fitting and secure it with the 3 4 hose clamp supplied in Bag 2 then connect the other end of the brake booster hose to the fitting on the driver side of the supercharger air inlet and secure it with another hose clamp 125 Reattach the fuel injector electrical connectors Brochure 763 1598 Rev 2 11 AJ mc Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 126 Use a small flat blade screwdriver to remove the wire loom covers from the back of the ignition coil bracke
21. itting with a supplied hose clamp 106 Lower the intercooler reservoir and its attached hose down into the passenger side of the engine bay so that the lower bracket will line up with the standoff stud the upper bracket will line up with the passenger side radiator fan assembly bolt and the hose will mate up to the intercooler water pump 107 Use a 13mm socket to reinstall the stock radiator fan assembly bolt through the upper reservoir bracket 108 Use a 10mm socket to install the stock nut removed from the radiator fan onto the standoff stud to secure the lower intercooler reservoir bracket 109 Secure the intercooler reservoir to water pump hose to the inlet of the water pump with a supplied hose clamp 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 16 Rev 2 11 AJ mc Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 110 Install the factory o ring intake seals into the machined grooves of the supercharger flanges 111 Install the factory throttle body o ring into the machined groove on the supercharger air inlet 112 Install the Manifold to EVAP Solenoid Hose to the fitting directly below the supercharger hub snout and the Driver Side PCV Hose to the staight fitting on the driver side of the air inlet 113 Connect the TMAP harness to the TMAP sensor at the rear of the supercharger manifold 114 Clear the engine valley of any tools or equipment the
22. mpromised then install the seals into the supplied valley plate Brochure 63 1598 Rev 2 11 AJ mc SUPERCHAR BY GERS Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 46 Install the new valley plate on the engine carefully so as not to dislodge the o rings and line up the bolt holes _ 47 Apply anti seize to the underside of the heads of the eleven countersunk bolts from Bag 3 then use a 5mm Allen tool to install them in the plate Torque them to 18 ft lbs from the center out 48 Apply thread sealant to the threads of the oil pressure sensor then use a crescent wrench to install the sensor in the new valley plate Reconnect the oil pressure sensor electrical connector 49 Use a 15mm socket to remove the two bolts retaining the belt tensioner m ti 50 Place a drain pan below the radiator petcock on the driver side Remove the radiator cap then loosen the petcock to drain the engine coolant 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 11 51 Disconnect the two heater hoses from the firewall using a shop rag to absorb any excess coolant 52 Disconnect the two heater hoses from the water pump using a shop rag to absorb any excess coolant A ene ee We P ws i ET cQ FS L 4 F E n 4 1 T EN ada 4
23. n remove the tape covering the intake ports and lift the supercharger d onto the engine 115 Connect the Manifold to EVAP Solenoid Hose attached to the manifold to the bottom fitting on the EVAP solenoid by routing the hose down and behind the idler pulley bracket Brochure 263 1598 222238 SUPERCHARGERS BY 116 Use a 10mm universal socket to install the M6 x 45mm intake manifold bolts supplied in Bag 3 and torque them to 89 in Ibs in the sequence shown below 117 Route the supplied serpentine belt according to the diagram below except for the idler pulley adjacent to the tensioner Use a 16mm wrench to push the tensioner in enough for the belt to slip on the idler pulley then inspect the belt installation to make sure it is properly aligned 118 Apply o ring lube to the seals of each of the fuel rail fittings Use a 13 16 wrench to install the plug in the rear of the driver side rail and a 3 4 wrench to install the crossover fittings in both rails as well as the inlet fitting at the rear of the passenger side rail Clock the inlet fitting to the rounded side of the fuel rail 119 Apply o ring lube to the upper seals of the supplied fuel injectors and install them into the supplied fuel rails so that the electrical connectors are oriented towards the rounded side of the rails 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 17 Edelbrock E Force Supercharger System
24. o remove the three bolts retaining the starter heat shield 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 13 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 69 Disconnect electrical connector at top of starter 70 Use a 13mm socket to remove the nuts retaining power wires to the starter 71 Remove and set aside the starter and bracket 72 Install GM Flywheel Holding Tool J 42386 A to prevent the crank from rotating while loosening the balancer bolt and torque the bolts holding it to 37 ft lbs 73 Use a breaker bar and a 24mm socket to loosen and remove the crank bolt A long pipe slid over the breaker bar can be helpful for increasing leverage 74 Install the drill guide and the M16 x 120mm bolt supplied in Bag 4 onto the end of the crankshaft 75 Measure 1 7 from the tip of the 15 64 drill bit supplied in Bag 4 and mark the position with a piece of masking tape then drill into the crank through the hole in the guide that has a bushing in it until the tape mark reaches the drill guide 76 Loosen the bolt holding the drill guide and rotate it until the second hole lines up with the hole drilled in the crank Use the back side of the ream tool to verify the guide is correctly aligned 77 Tighten the guide bolt then use compressed air to clean out any metal flakes in the drill hole 78 Insert the supplied ream tool through the hole and ream the
25. ock LLC Part 1596 1597 1598 amp 1599 Brochure 63 1598 Page 6 Rev 2 11 AJ mc UPERCHARGERS BY 1 Open trunk and lift trunk liner to access plastic hold down Unscrew plastic hold down then remove air compressor and foam support 2 Use a 10mm socket to loosen and remove the negative battery terminal 3 Lift the protective cover then use a 10mm socket to loosen and remove the positive battery terminal 4 Lift and support the front end of the vehicle using a service lift or jack and appropriately load rated jack stands then loosen and remove the lug nuts from both front wheels Remove the wheels and set them aside 5 Use a 120 Torx wrench to remove the three bolts on each side holding the front and the two holding the rear of the front wheel fender liners Use a panel puller to remove the five body pins on each side that retain the inner fender wells then remove them and set them aside 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 7 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 6 Reach in through the wheel wells with a 10mm socket to remove the four bolts at the front of each side of the fascia then use a 7mm socket to remove the two bolts on each side of the front fascia 7 Disconnect the fog lamp electrical connectors and the fascia wiring harness connector on the passenger side 8 Use a 10mm socket to remove the two bolts r
26. or stamped flanges They are direct replacements for stock manifolds so installation is simple using the factory crossover pipe Headers are made of durable 16 gauge mild steel and are 50 state street legal Two finishes are available Ti Tech or ceramic coating Shorty Headers for 2010 Camaro SS Ti Tech Coated n 65713 Ceramic Coated 65712 One 4 WU ES Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 85 Eibach produces springs with unparalleled precision and quality using Hi Ten spring steel produced to exacting tolerances Custom CNC coilers yield race quality springs with street friendly performance and great looks The progressive rate design produces excellent ride quality and aggressive handling characteristics These springs combined with Edelbrock suspension components will improve your vehicles handling performance cornering ability and braking stability Eibach Coil Spring Set 5237 The all new Edelbrock Adjustable Rear Toe Links help keep the tires planted firmly on the ground and pointed in the right direction to improve handling performance They are constructed with aluminum adjustment sleeves 5 8 heavy duty Heim joint rod ends and urethane bushings for strength and stability They replace OEM arms produced from stamped steel that can deform under hard cornering
27. or and plug it into the color matched receptacle on the relay harness 154 Install the grommet supplied in Bag 6 in the hole P At M 4 ij on the passenger side coil cover 155 Slide the front fascia back into place and secure it by reinstalling the stock fasteners including six body pins and two bolts on top three 10mm and two 7mm bolts inside the fascia on each side and two 10mm bolts on the underside 151 Clip the supplied EVAP solenoid electrical connector on the relay harness into the EVAP solenoid 2011 Edelbrock LLC Brochure 763 1598 Part 1596 1597 1598 amp 1599 Page 20 Rev 2 11 AJ mc Edelbcock FORCE SUPERCHARGERS 156 Reconnect the fog light electrical connectors and the fascia wiring harness connector on the passenger side 157 Use a 10mm socket to reconnect the positive battery terminal 158 Use a 10mm socket to reconnect the negative battery terminal 159 Remove intercooler reservoir cap and fill intercooler system with a 50 50 blend of water and coolant 160 Refill the engine coolant system with a 50 50 blend of water and coolant 161 Reinstall and secure the front inner fender wells with the stock fasteners 162 Reinstall the front wheels and snug the lug nuts Lower the vehicle to the ground then torque the lug nuts in a crossing pattern to 100 ft Ibs 163 It is recommended that you check the Edelbrock website http www edelbrock com automotive new mc superch
28. per so that the lower bracket holes line up with those in the radiator shroud 91 Secure the top of the heat exchanger with the two M8 x 20mm bolts supplied in Bag 2 and tighten them with a 12mm socket 92 Install the M8 nuts and M8 x 20mm bolts supplied in Bag 2 into the holes in the lower heat exchanger brackets then use a 12mm wrench and socket to tighten them 93 Install the intercooler water pump bracket on the studs located on the back of the passenger side of the bumper Secure it in place with the M8 nuts supplied in Bag 2 and tighten them with a 12mm wrench Brochure 763 1598 Rev 2 11 AJ mc SUPERCHAR GERS 94 Install the water pump to heat exchanger hose on the passenger side inlet fitting of the heat exchanger and clock it until it contacts the lower radiator shroud Secure the fitting with a 3 4 hose clamp supplied in Bag 2 95 Slide the strap over the body of the water pump and install it in the water pump bracket Rotate the water pump and slide it in and out until it roughly lines up with the position of the hose on the other side of the lower radiator shroud 96 Use a uni bit to drill a 1 1 8 hole in the lower radiator shroud to allow the hose to slide onto the water pump outlet fitting 97 Use the supplied bolt and a 13mm socket to secure the water pump by tightening the strap to the bracket 98 Slide the hose onto the water pump outlet and secure it with a 3 4 hos
29. rations take place during this step while vehicles with an automatic transmission will have five Completion of each operation will cause the progress bar to reset to zero DO NOT unplug the programmer until prompted 174 Turn the car off when prompted to do so by the handheld programmer 175 Read parting message from programmer then press Select to continue 176 Unplug the programmer cable from the OBD II port Brochure 63 1598 Rev 2 11 AJ mc 222238 SUPERCHARGERS BY 177 Start the car and allow it to idle while closely inspecting the engine bay for any fuel or coolant leaks Repair any leaks before operating vehicle 178 Remove the engine oil dipstick 179 Lubricate the grommet on the passenger side coil cover then install it by sliding the grommet down and around the dipstick tube and pressing the ball studs into the bracket grommets 180 Return the dipstick to the dipstick tube 181 Install the driver side coil cover by sliding it into place and pressing the ball studs into bracket grommets 182 Congratulations on the installation of your new Edelbrock E Force Supercharger System If you have any questions please call our Technical Support hotline and one of our technicians will be happy to assist you 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 22 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions
30. the side facing passenger side fitting Push each hose end on until it clicks into place Brochure 763 1598 Rev 2 11 AJ mc SUPERCHARGERS 137 Use a 16mm wrench to install the coil cover standoffs on the valve covers 138 Use a 10mm socket the four stock bolts and the stock o ring gasket to install the throttle body on the supercharger air inlet flange 139 Route the TMAP wiring harness below the supercharger hub snout towards the driver side using care to secure it well away from the serpentine belt 140 Connect the ETC extension harness to the stock ETC electrical connector and route the extension harness so that it will clear the serpentine belt and connect it to the ETC connector on the throttle body 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 19 Edelbrock E Force Supercharger System for the 2010 Camaro SS Installation Instructions 141 Use a T20 Torx bit to remove the MAF sensor from the stock air box cover and install it in the supplied air box cover The arrow on the side of the sensor should point back towards the supercharger 142 Replace the stock air filter with the one supplied 143 Slide the supplied worm clamps over each end of the supplied silicone tube then slide the tube onto the outlet of the supplied air box cover Install the cover by sliding the tabs into the holes on the driver side of the air box while sliding the silicone tube onto the throttle
31. ts gt 128 Use a 10mm socket to remove the two bolts holding the ignition coils for cylinders 2 3 6 amp 7 129 Locate the supplied coil cover brackets on top of the ignition coils then reinstall the ignition coil bolts 130 Use a 10mm wrench to remove the valve cover ball stud from the driver side cover 2 131 Use a pair of pliers to remove the vacuum cap from the rear of the driver side valve cover 2011 Edelbrock LLC Part 1596 1597 1598 amp 1599 Page 18 132 Use a 10mm socket to reinstall the coil brackets using the five stock studs on each side then reconnect the ignition coil harness electrical connectors and the spark plug wires to the ignition coils 133 Route the Driver Side PCV hose under the Brake Booster to Manifold Hose and behind the coil cover brackets to the vacuum fitting at the rear of the driver side valve cover and clip it into place 134 Install the Passenger Side Manifold to Intercooler Reservoir Hose between the manifold and reservoir then secure the reservoir fitting with a hose clamp supplied in Bag 2 135 Install Driver Side Manifold to Intercooler Reservoir Hose between the manifold and reservoir then secure the reservoir fitting with a hose clamp supplied in Bag 2 WE i 136 Connect the Intercooler Hose Assembly to the rear facing driver side fitting and
Download Pdf Manuals
Related Search