Drill Masters Eldorado Tool Drill Right Angle Cordless Drill 18 Volt User's Manual
Contents
1. When servicing a tool use only identical replacement parts Follow instructions in the Inspection Maintenance And Cleaning section of this manual Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury SPECIFIC SAFETY RULES di Maintain a safe working environment Keep the work area well lit Make sure there is adequate surrounding workspace Always keep the work area free of SKU 92383 For technical questions please call 1 800 444 3353 PAGE 4 obstructions grease oil trash and other debris Do not use the Cordless Drill in areas near flammable chemicals dusts and vapors Do not use this product in a damp or wet location 2 Maintain labels and nameplates on this product These carry important infor mation If unreadable or missing contact Harbor Freight Tools for a replacement 3 When using the Cordless Drill always maintain a firm grip on the tool with both hands 4 Hold the tool by its insulated gripping surfaces when performing an opera tion where the Cordless Drill may contact hidden wiring Contact with a live wire will make exposed metal parts of the Cordless Drill live and shock the operator 5 Do not use the Cordless Drill or Charger 41 if it has been dropped dam aged left outdoors or immersed in liquid 6 To avoid electrical shock do not handle the Charger 41 its Power Cord Plug or the Cordless Drill with wet hands2. not use damaged equipment 3 Battery Pack 27 precautions Never burn Batteries as they can explode in a fire Do not charge leaking Batteries Only a qualified service technician should perform maintenance on the Battery Pack Contact local solid waste authorities for instructions on correct disposal or recycling of the Battery Pack 4 DAILY With a soft brush or cloth remove all dirt and debris from the Cordless Drill Do not immerse the Cordless Drill in any liquids 5 When storing Always remove the Battery Pack 27 from the Cordless Drill Keep the Cordless Drill and its accessories in a clean dry location and out of childrens reach PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO SKU 92383 For technical que
3. shank of a Drill Bit all the way into the Chuck While holding the Chuck Sleeve in place turn the Chuck counterclockwise to lock the Drill Bit in place See Figure A 3 Power Switch 20 The Power Switch is operated manually simply by squeezing the Power Switch to turn on the Cordless Drill and releasing pressure on the Power Switch to turn off the Cordless Drill See Figure A 4 Forward Lock Reverse Lever The Forward Lock Reverse Lever allows you to change the rotational direction of the Cordless Drill and also to lock the Power Switch 20 in its OFF position To change the rotational direction make sure the Cordless Drill is at a complete stop Whiie holding the Cordless Drill in your hand move the Lever to the eft for a clockwise rotation For a counterclockwise rotation move the Lever to the right To lock the Power Switch in its OFF position move the Lever midway between the left and right settings See Figure A LEFT amp RIGHT HEAD GRIPS CHUCK SLEEVE 5 13 AIR VENT FORWARD LOCK REVERSE LEFT amp RIGHT GRIPS SWITCH 4 21 POWER SWITCH 20 BATTERY PACK 27 CARRYING STRAP FIGURE A 39 SKU 92383 For technical questions please call 1 800 444 3353 PAGE 7 5 Left amp Right Grips 4 21 Left amp Right Head Grips 5 13 The Left amp Right Grips and Left amp Right Head Grips allow for safer and easier operation of the Cordless Drill IMPORTANT When operating the Co
4. tired or under the influ ence of drugs alcohol or medication A moment of inattention while operat ing power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure the Power Switch 20 is released before plugging in Carrying power tools with your finger on the Power Switch or plugging in power tools with the Power Switch depressed invites accidents Remove adjusting keys or wrenches before turning the power tool on A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper footing and balance enables better control of the power tool in unexpected situations Use safety equipment Always wear ANSI approved safety glasses underneath a full face safety shield Dust mask non skid safety shoes hard hat or hearing protection must be used for appropriate conditions Use clamps not included or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is unstable and may lead to loss of control SKU 92383 For technical questions please call 1 800 444 3353 PAGE 3 TOOL USE AND CARE 1 Do not force the tool Use the correct
5. 7 Keep the Handle of the Cordless Drill dry clean and free from oil and grease 8 Always turn off the Cordless Drill and unplug the Charger 41 from its electrical outlet before changing accessories or performing any inspec tion maintenance or cleaning procedures 9 Avoid unintentional starting Make sure you are prepared to begin work before turning on the Cordless Drill 10 To avoid electrical shock do not pull or carry the Charger 41 by its Power Cord 11 Never leave the Charger 41 unattended when it is plugged into an electrical outlet Make sure to unplug it from its electrical outlet before leaving 12 Proper Battery Pack Care Battery Pack 27 leakage may occur under extreme usage or temperature conditions If Battery Pack fluid comes in contact with skin wash with soap and water and rinse with lemon juice and vinegar If the fluid comes into contact with the eyes flush with water for several minutes and con tact a doctor immediately Never burn the Battery Pack as it can explode in a fire Do not charge the Cordless Drill with a leaking Battery Pack Contact local solid waste authorities for instructions on correct disposal or recycling of the Battery Pack SKU 92383 For technical questions please call 1 800 444 3353 PAGE 5 Always switch to a fresh Battery Pack 27 when tool performance begins to diminish Severe heat is most destructive to a Battery Pack The more heat generated the faster the Battery Pack
6. DRILL L MASTER RIGHT ANGLE CORDLESS DRILL 18 VOLT Model 92383 OPERATING INSTRUCTIONS A HARBOR FREIGHT _ 3 TOOLS Gz 3491 Mission Oaks Blvd Camarillo CA 93011 Visit our Web site at http www harborfreight com TO PREVENT SERIOUS INJURY READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE Copyright 2004 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions or replacement parts please call 1 800 444 3353 PRODUCT SPECIFICATIONS Electrical Requirements Power Source 18 VDC Rechargeable Battery Battery Type NI MH 1300 MAH 15 Cell 1 2V Initial Charge Time 5 Hours Subsequent Charge Times 3 Hours Charger Input 120 VAC 60 Hz Charger Output 24 VDC 400 MA Motor 0 900 RPM No Load Reversible Chuck Type 3 8 Keyless Accessories 2 Double End Bits Qty 2 AC DC Charger Base 4 60 Pounds UNPACKING When unpacking check to make sure all the parts shown on the Parts List on page 11 are included If any parts are missing or broken please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible SAVE THIS MANUAL You will need this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures parts list and
7. as sembly diagram Keep your invoice with this manual Write the invoice number on the inside of the front cover Keep this manual and invoice in a safe and dry place for future reference GENERAL SAFETY RULES AN N WARNING gt a READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious injury SAVE THESE INSTRUCTIONS WORK AREA 1 Keep your work area clean and well lit Cluttered benches and dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes SKU 92383 For technical questions please call 1 800 444 3353 PAGE 2 Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control Protect others in the work area from debris such as chips and sparks Provide barriers or shields as needed ELECTRICAL SAFETY Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock PERSONAL SAFETY Stay alert Watch what you are doing and use common sense when oper ating a power tool Do not use a power tool while
8. ating power tools alone Don t use a power tool with the power switch locked on If powered via a power cord be certain that the tool is properly grounded A ground fault interrupt GFCI system is also a good precaution This inexpensive device is a good safety measure because it prevents a sustained electrical shock Properly main tain and inspect all tools before use to avoid electrical shock Z WARNING The warnings precautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur The operator must understand that common sense and caution are factors which cannot be built into this product but must be supplied by the operator PRODUCT FEATURES NOTE For additional information regarding the parts listed in the following pages refer to the Assembly Diagram on page 11 A WARNING Always make sure the Power Switch 20 of the Cordless Drill SKU 92383 For technical questions please call 1 800 444 3353 PAGE 6 is in its OFF position the Battery Pack 27 is removed from the Cordless Drill and the Charger 41 is unplugged from its electrical outlet prior to making any adjustments to the tool See Figure A below and Figure B next page 2 Chuck 7 Accepts up to 3 8 shank diameter Drill Bits not included To install a Drill Bit with the Cordless Drill pointed away from your body hold the Chuck Sleeve firmly in place and turn the Chuck clockwise Insert the
9. e Power Switch 20 Do not drill deeper than necessary into walls or other areas where you cannot identify any possible hazards such as electric wires and cables behind the drilling surface Drill only as deep as necessary To reduce jamming as the Drill Bit breaks through the workpiece decrease the drilling pressure when the point of the Drill Bit breaks through the workpiece When you have drilled the hole remove the Drill Bit from the hole while the Cordless Drill is still running This prevents the Drill Bit from getting caught in the hole and causing damage Release the Power Switch 20 to stop the Cordless Drill Then remove the Battery Pack 27 and Drill Bit from the Cordless Drill SKU 92383 For technical questions please call 1 800 444 3353 PAGE 9 INSPECTION MAINTENANCE AND CLEANING Note Servicing of this tool should only be done by a qualified service technician Z WARNING Always turn the Power Switch 20 to its OFF position and unplug the Charger 41 from its electrical outlet before performing any inspection maintenance or cleaning 2 BEFORE EACH USE inspect the general condition of the Cordless Drill Check for misalignment or binding of moving parts cracked or broken parts leaking Battery Pack damaged Charger wiring chipped or broken Drill Bits and any other condition that may affect its safe operation If abnormal noise or vibration occurs have the problem corrected before further use Do
10. is is normal and does not indicate a problem See Figure B 6 Once the Battery Pack 27 is fully charged disconnect the AC DC Adapter from the electrical outlet Then disconnect the Charger 41 from the Battery Pack See Figure B SKU 92383 For technical questions please call 1 800 444 3353 PAGE 8 OPERATING INSTRUCTIONS 11 12 13 When installing Drill Bits make sure the Battery Pack 27 is removed from the Cordless Drill to avoid accidental starting Then insert and lock in place a Drill Bit in the Chuck 7 of the Cordless Drill If necessary adjust the Forward Lock Reverse Lever See Figure A Whenever possible secure the workpiece in place using a vise or clamps not included When drilling in light gauge metal or wood use a wooden block to back up the material to prevent damage to the workpiece Mark the center of the hole to be drilled with a center punch to give a Drill Bit a start and to prevent it from walking Lubricate the Drill Bit with cutting oil when drilling iron or steel Use a coolant when drilling non ferrous metals such as copper brass or aluminum Insert the fully charged Battery Pack 27 into the Handle of the Cordless Drill See Figure A Make sure to hold the Cordless Drill firmly by the Left amp Right Grips 4 21 and Left amp Right Head Grips 5 13 with both hands as torque from the Motor will cause the tool to twist Turn the Cordless Drill on using th
11. loses power A Battery Pack that gets too hot can be permanently damaged Never over discharge a Battery Pack by using the tool while tool performance is decreasing Never attempt to discharge a tool s Battery Pack by continuing to pull the tool s Power Switch 20 When tool performance begins to diminish stop the tool re charge the Battery Pack and use the fresh Battery Pack for optimal performance A WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contain chemicals known to the State of Cali fornia to cause cancer birth defects or other reproductive harm Some ex amples of these chemicals are lead from lead based paints crystalline silica from bricks and cement or other masonry products arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles California Health amp Safety Code 25249 5 et seq ZA WARNING People with pacemakers shoul consult their physician s before using this product Electromagnetic fields in close proximity to a heart pace maker could cause interference or failure of the pacemaker In addition people with pacemakers should adhere to the following Avoid oper
12. rdless Drill hold the tool with both hands by its Grips only Do not cover the Vent of the tool with your fingers or hands Doing so will cause the Motor to overheat causing damage to the tool See Figure A TO CHARGE THE CORDLESS DRILL 1 NOTE The Battery Pack 27 requires charging The first charge requires 5 hours charge time prior to using the Cordless Drill See Figure B 2 When the Battery Pack 27 requires re charging a 3 hour fast charge allows the tool to operate at full power Do not re charge the Battery Pack longer than 5 hours as damage to the Battery Pack and or Charger 41 will occur See Figure B 3 Make sure the Power Switch 20 on the Cordless Drill is in its OFF position Slide the Battery Pack 27 off the Handle of the Cordless Drill Insert the Adapter Prong into the Charger 41 Next slide the Charger onto the Battery Pack Then plug the AC DC Adapter into the nearest 120 volt grounded electri cal outlet See Figure B 4 When illuminated the RED light on the Charger 41 indicates charging is in process When illuminated the GREEN light on the Charger indicates the Bat tery Pack 27 is fully charged and should be removed from the Charger See Figure B AC DC ADAPTER ADAPTER PRONG BATTERY PACK 27 E TO 120 VOLT GROUNDED ELECTRICAL OUTLET CHARGER 41 FIGURE B 5 NOTE While charging the Battery Pack 27 and Charger 41 may become warm to the touch Th
13. stions please call 1 800 444 3353 PAGE 10 PARTS LIST amp ASSEMBLY DIAGRAM ipti Qty Left Head Grip ip i il Beari po HS A w w 0 00 09 09 Vv 9 9 JP JP JP Py Po PO HALO JOD INIDINIHRIW M JO O OIN DIO o p 10 13 14 an 38 K 41 CHARGER ADAPTER NOT SHOWN NOTE Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 92383 For technical questions please call 1 800 444 3353 PAGE 11
14. tool for your application The correct tool will do the job better and safer at the rate for which it is designed 2 Do not use the power tool if the Power Switch 20 does not turn it on or off Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced 3 Disconnect the power tool from its Battery Pack 27 before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool accidentally 4 Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users 5 Maintain tools with care Keep drill bits sharp and clean Properly maintained tools with sharp drill bits are less likely to bind and are easier to control Do not use a damaged tool Tag damaged tools Do not use until repaired 6 Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly main tained tools 7 Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool SERVICE al Tool service must be performed only by qualified repair personnel Service or maintenance performed by unqualified personnel could result in a risk of injury 2
Download Pdf Manuals
Related Search