Digi MIL-170TRM User's Manual
Contents
1. MIL 170TRM 10BASE FL to 10BASE T Media Converter for Digi s Media Conversion System Thumbscrews TP FX 9 10BASE FL D MDI X MDI AGTCACT _ _e 9 od ag TP FX MIL 10BASE T LINK LINK TX RX 170TRM Installation Guide This guide includes the following Introduction on page 2 Features on page 2 4 Installation on page 2 MDI X MDI Switch on page 3 4 Link Sentry Configuration on page 3 4 Indicators on page 4 4 Specifications on page 4 4 Operating Conditions on page 5 4 Legal Declaration on page 6 Doc 90000096 Rev A Install Guide Dial About this Manual This document covers the MIL 170TRM media converter module The terms MIL 170 MIL 170TRM and converter are used throughout this document to describe the MIL 170TRM Introduction The MIL 170TRM is one of a series of modules designed to be installed into Digi s Media Conversion System This half full duplex device converts optical signals to electrical and vice versa The device has a signal capability of transmitting up to 15 km subject to fiber budget and collision domain restrictions This module also has the Link Sentry feature Features One RJ 45 UTP connector One single mode ST connector Link Sentry feature Diagnostic LEDs Management ready supplied by the optional SNMP modules MIL 4650 and MIL 4655 Power supply equipped on2. The Link Sentry feature on the MIL 170TRM is configured through a 4 position DIP switch refer to Figure 1 Default setting for the DIP switches All switches are in the up position Link Sentry allows users to add new management tools to the network When enabled it monitors the selected receiver port and if the Link test signal is not seen the unit will stop sending a signal through the selected transmit port Model MIL 170TRM 3 Install Guide The following table shows which Link Sentry feature is enabled Table 1 Link Sentry Features Note For two MIL 170s used back to back and UTP to UTP all DIP switches must be enabled in the down position on the first MIL 170 On the second MIL 170 enable switches 1 and 4 in the down position Default setting for Link Sentry All switches set in the up position disabled When using the SNMP module to control the Link Sentry feature leave the switches in the default mode up Indicators There are four LEDs including Switch Losing Link on RX of Stop sending Link on TX of 1 down Fiber port Fiber port 2 down UTP port UTP port 3 down UTP port Fiber port 4 down Fiber port UTP port TP ACT Receiving packets from the 1OBASE T port TP LINK There is an active connection on the 1OBASE T port FX LINK There is an active connection on the 10BASE FL port FX ACT Receiving packets from the 1OBASE FL port Specifi
3. the rack mount chassis Installation Do the following to install the MIL 170TRM into a redundant rack mount chassis 1 2 3 4 Make any configuration changes to the module i e DIP switch settings Remove the screws securing the faceplate and remove it from the chassis Slide the module into the slot through the guide rails Insert the module into the card edge connector port bay Make sure it is seated firmly Secure the module with the two thumbscrews located on the faceplate of the unit The unit is now ready for network connections Model MIL 170TRM 2 Install Guide Dia MDI X MDI Switch The MDI X MDI switch allows for quick configuration of the 10BASE T port Cables used when the switch is in the MDI X position the left position For a hub repeater use a swap cable pins are connected 1 to 3 2 to 6 3 to 1 and 6 to 2 For a workstation PC use a straight through cable pins are connected 1 to 1 2 to 2 3 to 3 and 6 to 6 LI 4 pin DIP Switch RJ 45 Female raf Connector 4 total MDI X MDI Switch ST Type Connectors Figure 1 Inside of the MIL 170TRM Cables used when the switch is in the MDI position the right position For a hub repeater use a straight through cable pins are connected 1 to 1 2 to 2 3 to 3 and 6 to 6 For a workstation PC port use a swap cable pins are connected 1 to 3 2 to 6 3 to 1 and 6 to 2 Link Sentry Configuration
4. cations RJ 45 MDI e Pin 1 Transmit Data e Pin 2 Transmit Data e Pin3 Receive Data e Pin 6 Receive Data RJ 45 MDI X e Pin 1 Receive Data e Pin 2 Receive Data e Pin3 Transmit Data e Pin 6 Transmit Data Model MIL 170TRM Install Guide 234 5678 Figure 2 RJ 45 Pinouts Fiber Specifications ST connector e 1300 nm single mode fiber e 8or 9 125 um single mode fiber e Launch power 19 dBm e Receive sensitivity 36 dBm Operating Conditions Table 2 Recommended Operation Conditions Model MIL 170TRM Parameters Minimum Maximum Operating Temperature 5 C 50 C Humidity Non condensing 10 95 Signal Output Load 35 ohm 75 ohm Supply Voltage 4 75 V 5 25 V Dich Legal Declaration Regulatory Approvals FCC Class A UL 1950 CSA 22 No 950 EN60950 CE EN55022 Class B EN50082 1 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada European Notice Products with the CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the commission of the European Community Compliance with these directives implies conformity to the following European Norms e EN55022 CISPR 22 Ra
5. dio Frequency Interference e EN50082 1 IEC801 2 IEC801 3 IEC801 4 Electromagnetic Immunity e EN60950 IEC950 Product Safety Five Year Limited Warranty Digi International warrants to the original consumer or purchaser that each of its products and all components thereof will be free from defects in material and or workmanship for a period of five years from the original factory shipment date Any warranty hereunder is extended to the original consumer or purchaser and is not assignable Digi makes no express or implied warranties including but not limited to any implied warranty of merchantability or fitness for a particular purpose except as expressly set forth in this warranty In no event shall Digi be liable for incidental or consequential damages costs or expenses arising out of or in connection with the performance of the product delivered hereunder Digi will in no case cover damages arising out of the product being used in a negligent fashion or manner To Contact Digi For prompt response when calling for service information have the following information ready e Product serial number and rev e Date of purchase e Vendor or place of purchase Reach Digi Technical Support at 408 744 2751 Or E mail at sun tech dgii com Address 1299 Orleans Drive Sunnyvale CA 94089 Voice 408 744 2775 Fax 408 744 2793 E mail info dgii com Doc 90000096 Rev A
Download Pdf Manuals
Related Search