Home
Daewoo Electronics DSB-F154LH User's Manual
Contents
1. Light on during the Plasma mode Switch Panel EMERGENCY REMOTE Bi When the remote con troller is lost or out of order put the switch on the EMERGENCY to operate by hand Open the front panel on emergency operating Remote mode is used with remote controller DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 2 5 7 REMOTE CONTROLLER DSB F154LH xe n Display zu m a Displays information um RIO e pertaining to unit ON OFF Button Press to turn the unit on or off TEMPERATURE Buttons Press to raise or lower FAN SPEED Button Press to select the fan speed a db the desired temperature High F Middle Low MODE FANSPEED FAN DIR AY FAN DIR AY Button Natural Press to select up down C direction for fan MODE Button SLEEP PLASMA FAN DIR 4 gt Press to cycle through the modes aa FAN DIR lt gt Button Auto Quick Cool Fan Dehumidifier e Press to select left right Heat Heg een direction for fan SLEEP Button TURBO MILD Press to select super power operation Turbo mode Press to set the unit for the sleep mode PLASMA Button Press to purify the air Only DSB F154PH TIMER ON OFF Button Press to set the unit off or on time 0 5 1 1 5 2 2 5 3 4 5 6 8 10 12 16 20 24hr TIMER ENTER CANCEL Button Press to ent
2. Connection Cover Remove cover to access the AC connection from this unit to the indoor unit Service Valves The indoor and outdoor units are connected by copper tubes which are connected here DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM II 9 5 INDOOR UNIT DISPLAY Indoor Unit Display mw Remote Control Signal Receiver This place is the part to receive the signal if it receives the signal you can hear the signal beep beep DSB F154AH DSB F154LH DSB F154PH TIMER C r QUICK CD OXYGEN CD p ONC Timer Yellow Light on during the time of reservation mode Quick Red ON Red Light on during the operation Oxygen Green Light on during the time of Quick Mode Light on during the Oxygen mode m TIMER CD QUICK CD AIR CLEAN CO p ONC Timer Yellow Light on during the time of reservation mode Quick Red L ON Red Light on during the operation Air clean Green Light on during the time of Quick Mode Light on during the operation m TIMER CI QUICK CD PLASMA CD ONC Timer Yellow Light on during the time of reservation mode Quick Red ON Red Light on during the operation Plasma Green Light on during the time of Quick Mode
3. Then set the desired GED light on the indoor unit and ON temperature using the TEMP A or V will light in the remote display buttons MODE 3 Press the SLEEP button on the remote controller TO CANCEL SLEEP MODE The unit will then be in the sleep mode and will cool the room to the desired a To cancel sleep mode press temperature After a while the unit will the SLEEP button again the increase the temperature again SLEEP SLEEP indicator will disappear qy e This process will then repeat in the display TO SET TURBO MILD MODE 1 The unit is tixed MILD mode on production 2 Press the TURBO MILD button for powerful operation After 30 minutes function returns automatically to MILD mode 3 TURBO button does not operate in a HEAT mode e TURBO MILD 4 When press the TURBO MILD button one more time it will be back to MILD mode EMERGENCY OPERATION If the remote control is lost broken or has no batteries follow the procedures below 1 Open the indoor unit s cover and make sure the EMERGENCY REMOTE switch is set to the EMER GENCY position EMERGENCY REMOTE Switch 2 The unit will then turn on and depending on the room temperature it will select the cool or dehumidifier mode fan speed and fan direction automatically qu MODE 3 To turn the unit off slide the EMERGENCY REMOTE Switch to the R
4. in the remote display 2 Press the MODE button until the Quick C indi cator blinks MODE 3 The unit will then start cooling or heating the room at the highest power FAN auf TO SET UNIT TO COOL MODE To set the unit to cool the room to a desired temperature follow the procedures below 1 Press the ON OFF button on the remote control to turn the unit on the On LED will light on the indoor unit and ON will light in the remote display 2 Press the MODE button until the Cool appears Lx in the display D MODE indicator 3 Using the TEMP or A buttons set the desired tem perature The desired temperature can be changed up 4 To select the fan speed press the FAN SPEED button until the desired speed appears in the display see to 32 C and down to 18 C below Cy f Ja FAN SPEED amp FAN SPEEDS AUTO The fan will automatically select the fan speed EAM The fan will operate on low speed wo The fan will operate on medium speed wo The fan will operate on high speed NATURAL The fan will randomly cycle through the speeds simulating a cool breeze DS B F154 F 1 83 1 83L LH PH AH 2003 12 9 2 47 AM 16 TO OPERATE ONLY FAN To operate only the fan so the unit will circulate the air proceed as follows 1 Press the ON OFF button on the remote control to 2 Pr
5. is normal Strange smells occur The fan is bringing out the smells of the carpet walls etc The smell should go away shortly No remote operation Batteries are weak dead or inserted improperly Replace batteries Remote is out of range Move closer to unit Remote not aimed at sensor Aim remote at sensor There is an obstruction between unit and remote 16 Remove obstruction DS B F1 54 F 1 83 1 83L LH PH AH 2003 12 9 2 47 AM 4 27 INSTRUCTION OF INSTALLATION Below is an overview for the connection of the Indoor unit to the Outdoor unit OVERVIEW This appliance must be installed according to national power supply acquirement 10cm 3 95in from ceiling 30cm 11 8in from side wall 10cm 3 95in from side wall Wall war Drain SS KR Hose Wall Cap TT IEN e lt ILL ILI SA Oxygen tube At least 30cm 11 8in from unit Pipes Not Supplied AC Connection AC Outlet ee Not Supplied and Plug KY ppiied 1 Wrap with Tape Plug into 220V 240V AC Outlet Maximum Height 7M 21Ft Maximum Length 15M 49Ft Any tube length between 7 and 15 meters must 93 6 60 be precharge
6. the desired hour that you want the unit to turn on appears on the display For example if it is 1 00 P M and you want the unit to turn on at 4 00 P M select 3 hours r TIMER 4 Gai ND ON OFF ENTER CANCEL 4 Press the ENTER button to input the setting into memory the unit will beep the TIMER indicator will light on the unit and the TIMER indicator on the remote will light to indicate the unit is in the timer mode TIMER Gai ND ON OFF ENTER CANCEL 5 When the desired hour is reached the unit will turn on to the selected mode NOTE Press the ENTER button within 5 seconds of selecting the desired time If mote than 5 seconds elapse steps 3 and 4 must be repeated 10 DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 21 TO SET THE OFF TIMER MODE This unit can be set to automatically turn off after a predetermined amount of hours up to 12 in the order of 0 5 1 1 5 2 2 5 3 3 5 4 4 5 5 5 5 6 6 5 7 7 5 8 8 5 9 9 5 10 11 12 1 Press the ON OFF button of timer on the remote control to set the off timer mode HOUR and OFF on the remote display will be displayed and TIMER will be flicked When you increase to press ON OFF you will get desired time Then if pressing ENTER CANCEL button OFF TIMER Mode will be started If you want to stop OFF TIMER Mode please press ENTER CANC
7. 71 6 30 86 23 73 4 31 87 8 24 75 2 32 89 6 25 77 NOTES When operating the remote controller make sure there are no obstructions between the remote controller and the remote sensor After a while the display goes blank to conserve battery power To check the settings press the ON OFF button once TO SET THE UNIT TO AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode All you have to set is the desired temperature and it will control the fan coolness and dehumidifier Follow procedures below 1 Press the ON OFF button on the remote control to ine turn the unit on the On LED will light on the indoor Za Make Vieng indicator appears ies anit cis unit and ON will light in the play Using the TEMP W or A buttons set the desired rerote displa temperature The desired temperature can be changed up p ay b or down 1 degree from the actual room temperature For temperature setting 24 28 C wi Ja i o 3 Then the unit will automatically operate FAN asain Lu 6 DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 15 SET UNIT TO QUICK MODE To set this unit to cool or heat Heat pump model only at the highest power follow the procedures below 1 Press the ON OFF button on the remote control to turn the unit on the On LED will light on the indoor unit and ON will light
8. Contact your local electrical installer for installation INFORMATION 1 The plug shall be connected to a ground socket outlet and the interconnection cord shall be connected by an authorized electrician or specialist 2 Information for interconnection cable Items Specifications Under 12K class AC 250V 16A H05VV Fx1 0m Above 12K class AC 250V 16A H05VV Fx1 5m 3 Contact service man for the installation shall be in accordance with national wiring regulation HOW TO INSTALL BATTERIES To install the batteries follow the procedures below 1 Slide down the cover to access most of the remote buttons Slide down further to access the battery compartment 2 Insert two AAA size Alkaline batteries following the polarity diagram below TIMER ONOFF ENTER Te TURBOMILD BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device 1 Use only the size and type of batteries specified 2 Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Reversed batteries may cause damage to the device 3 Do not mix different types of batteries together e g Alkaline and Carbon zinc or old batteries with fresh ones 4 If the device is not to be used for a long period of time remove the batteries to prevent damage or injury from pos sible battery le
9. DS B F154 F 1 83 183L LH PH AH 2003 12 9 2 47 AM Hl 9 7 OWNER S MANUAL MODEL DSB F154LH CE S N 3113909901 DS B F1 54 F 1 83 183L LH PH AH 2003 12 9 2 47 AM H 1 C 5 SAFETY INSTRUCTIONS PLEASE READ THE FOLLOWING SAFETY INSTRUCTIONS BEFORE INSTALLING AND OPERATING THE UNIT This air conditioner meets strict safety and operating standards The installer of this unit must install or service this unit so it operates safe ly and efficiently IMPORTANT NOTES Adhere to all safety instructions and warnings throughout this manual Read this manual carefully before installing or operating this unit to become familiar with its features and obtain the perfor mance that will bring you continued enjoyment for many years Follow each installation or repair step exactly as shown in the manual Observe all local state and national electric codes Contact your local government for more information on electrical codes The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of suffi cient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the
10. EL again 2 Press the TIMER OFF button once to enter the Timer screen TIMER 4 cu m ON OFF ENTER CANCEL FAN r HOUR AUTO NON M OFF MER 3 Repeatedly press the TIMER OFF button until the desired hour that you want the unit to shut off appears on the display For example if it is 8 00 P M and you want the unit to turn off at 10 00 P M select 2 hours TIMER em ND ON OFF ENTER CANCEL 4 Press the ENTER button to input the setting into memory the unit will beep the TIMER indicator will light on the unit and the TIMER indicator on the remote will light to indicate the unit is in the timer mode TIMER 34 Ga ND ON OFF ENTER CANCEL 5 When the desired hour is reached the unit will turn off NOTE Press the ENTER button within 5 seconds of selecting the desired time If mote than 5 seconds elapse steps 3 and 4 must be repeated 11 DS B F1 54 F 1 83 1 83L LH PH AH 2003 12 9 2 47 AM 22 TO SET UNIT TO SLEEP MODE When you are going to sleep select this feature and the unit will cool off the room to the desired temperature and then increase that temperature throughout the night 1 Press the ON OFF button on the remote control to 2 Press the MODE button to select the turn the unit on the On LED will desired mode
11. EMOTE position EMERGENCY REMOTE Switch 12 DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM IH 9 23 CHANGING CLEANING THE AIR FILTERS To change or clean the two black air filters follow the procedures below 1 Open the indoor unit s cover and remove both black air filters by bending them slightly backward and the lifting out 2 Remove the two small filters Deodorizing and Electrostatic from the indoor unit After removing the connection terminal of electric dust collector remove the electric dust collector 3 Examine the filters and determine if they need to be cleaned or replaced To clean filters use a vacuum and clean off dust Use water and mild soap also if necessary NOTE The filters should be changed every 6 months If in a climate with cold winters once a year is adequate 4 Insert cleaned or new small filters Deodorizing and Electrostatic back into the unit After putting the connection terminal into electric dust collector insert the electric dust colloctor into the unit 5 Insert cleaned or new black filters back into the unit A Caution When you remove the electric dust collector you must remove the power plug 13 DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 9 24 CHANGING CLEANING THE AIR FIL
12. N OFF button on the remote control to turn the unit on the On LED will light on the indoor unit and ON will light in 2 Press the MODE button until the Heat indicator appears in the display In the heat mode the fan direction UP the remote display DOWN is further downward than that in MODE the cool mode for the good circulation 3 Using the TEMP or A buttons set the desired tem 4 To select the fan speed press the FAN perature The desired temperature can be changed up SPEED button until the desired speed qu to 32 C and down to 18 C appears in the display see below FAN SPEED NOTE When the heating orperation is started hot air deliv ery might be delayed due to warm up period FAN um ANO en m a C FAN SPEEDS AUTO The fan will automatically select the fan speed a The fan will operate on low speed iw The fan will operate on medium speed The fan will operate on high speed NATURAL The fan will randomly cycle through the speeds simulating a cool breeze TO SELECT THE FAN DIRECTION Regardless of the mode the unit is set for the fan direction can be changed so it moves up and down left and right or both Follow procedures below to set fan direction 1 Press the ON OFF button on the remote control to turn the unit on the On LED will light on the indoor unit and ON will light in the remote displa
13. TERS To change or clean the two black air filters follow the procedures below 1 Open the indoor unit s cover and remove both black air filters by bending them slightly backward and the lifting out 2 Remove the two small filters Deodorizing and Electrostatic from the indoor unit After removing the connection terminal of electric dust collector remove the electric dust collector LH PH AH Model Only 3 Examine the filters and determine if they need to be cleaned or replaced To clean filters use a vacuum and clean off dust Use water and mild soap also if necessary NOTE The filters should be changed every 6 months If in a climate with cold winters once a year is adequate 4 Insert cleaned or new small filters Deodorizing and Electrostatic back into the unit After putting the connection terminal into electric dust collector insert the electric dust colloctor into the unit Only DSB F154LH 154PH 154AH r 5 Insert cleaned or new black filters back into the unit cautionwhen you remove the electric dust collector you must remove the power plug INSTALLING THE REMOTE BRACKET To install the remote bracket insert one of the 2 supplied screws into top hole of
14. akage 5 Do not try to recharge batteries not intended to be recharged they can overheat and rupture Follow battery manu facturer s directions DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 9 x 14 SETTING THE UNIT FOR REMOTE OPERATION After the unit is fully connected and plugged in it can be turned on To turn the unit on and set it for remote operation follow the procedures below 1 Open the indoor unit s cover and make sure the EMER 2 Press the ON OFF button on the remote controller to turn GENCY REMOTE switch on the unit The On LED will light on the indoor unit and is set to the REMOTE ON will light in the remote display position this will allow the To select the various modes and unit to operate with the f settings read the following pages 5 remote controller EMERGENCY REMOTE Switch THREE MINUTE COMPRESSOR DELAY LL J After turning the indoor unit on and setting it for air condi REMOCON DEUS RENTE tioner operation the compressor outdoor unit will not come on for three minutes This is a feature that will protect the compressor from damage due to quick start and stops ARA EMERGENCY DSB 18 24 SERIES DSB 15 SERIES CELSIUS TO FAHRENHEIT CONVERSION CHART CELSIUS FAHRENHEIT CELSIUS FAHRENHEIT 18 64 4 26 78 8 19 66 2 27 80 6 20 68 28 82 4 21 69 8 29 84 2 22
15. appliance Contact Installer if Necessary The installation instructions are for a experienced installer If you are not an experienced installer contact a local installer for help If you require help with service contact your certified dealer or Daewoo Electronics for additional instructions If Unit is Installed Improperly The manufacturer shall in no way be responsible for improper instal lation or maintenance service including failure to follow the instruc tions in this manual WARNING ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH ONLY A QUALIFIED EXPERIENCED ELECTRICIAN INSTALLER SHOULD ATTEMPT TO WIRE THIS SYSTEM THE APPLIANCE IS NOT INTENDED FOR USE BY CHIL DRENOR INFIRM PERSONS WITHOUT SUPERVISION YOUNG CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT DO NOT PLAY WITH THE APPLIANCE Precautions When Wiring Do not plug in the unit until all connections tubing drain hose mounting etc have been made and double checked High voltages are present in this unit and are very dangerous Please refer to these instructions and diagrams when wiring Improper connections or inadequate grounding can cause acciden tal injury This unit must be grounded in accordance with local electrical codes Connect wires and pipes securely and tightly as loose connec tions wiring may cause overheating at connections and a possible fire hazard Precautions When Transporting When transport
16. d with freon using the following calulation in h cm Length 5 x 30 grams ones Adding additonal tubing will decrease efficiency S 3 9 inches 27 6 LIS NS inches i Ww 8 NOTES 2 B i e After installation it must be S E possible for the user to dis S L Copper J Drain connect the power supply uong Hose plug z a e If the AC outlet is a 3 star pronged type or other have 03 6 s round Wire a an electrician install a new 2 inches Not Supplied Lp outlet d e Contanct service man when cadum ciu GREMIEN UENIT d aed EE replace the power cord set assicepping lt ii as side piping e The specification of AC con Connecting COS Oxygen tube Connecting 209 Oxygen tube nection is 2 0mm x 3C x 6m cable QQ Liquid side piping cable ROQ Liquid side piping Drain Hose B Drain Hose Cooling Only Heating amp Cooling DSB AH Series model has oxygen tube but the other models do not 17
17. ediately unplug it from the wall 15 DS B F154 F 1 83 1 83L LH PH AH 2003 12 9 2 47 AM II 9 26 TROUBLESHOOTING GUIDE Before requesting service please refer to the chart below for possible solutions SYSPTOMS POSSIBLE CAUSE POSSIBLE SOLUTIONS No power Power failure Restore the power Line voltage too low Contact electrician to install new outlet Unit is unplugged or not completely plugged in Insert plug all the way Unit is off Turn unit on Batteries in remote are weak or dead Replace remote s batteries EMERGENCY REMOTE switch is not set to REMOTE Slide EMERGENCY REMOTE to REMOTE The compressor does not turn on no cool air at cooling no heat air at heating When the unit is first plugged in and turned on the compressor will delay turn on for 3 minutes Wait 3 minutes for the unit to operate If the unit is turned off and then immediately back on the compressor will delay for 3 minutes Wait 3 minutes for the unit to operate The air filter s is dirty or clogged Clean or replace filter s A door or window is open Shut door or window There is an obstacle in front of intake or indoor unit Remove obstacle The temperature has been set improperly Check and reset if necessary Strange sounds occur During operation especially after turning it on or off refrigerant flows inside the unit This
18. er a timer setting or to cancel timer setting COVER Slide down to access most of the remote buttons Slide down further to access the battery compartment REMOTE DISPLAY MODE Indicator Auto Quick Cool Fan Dehumidifier Heat Light to indicate the mode selected ay e 0 pe PLASMA Indicator AUTO qax Q Light to indicate the plasma mode Only DSB F154PH je ici FAN DIRECTION Indicator ght to indicate Light to indicate the the fan speed AUTO fan direction NATURAL Indicator NATURAL Light to indicate the epee LL Ed TIMER Indicators Include sleep Light to indicate the timer function mode TEMPERATURE amp RESERVATION TIME Indicator Light to indicate the temperature or time DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 4 13 OPERATION CONNECTING THE AC CORD The outdoor unit is connected to the indoor unit through the AC connecting wire or connection cord To connect the indoor unit to AC follow the procedures below 1 Insert the attached AC NOTES plug into a 2 pronged Never connect the AC line cord plug to other than the speci Only 220V or fied voltage Only 220V or 220V 240V 220V 240V AC outlet wae oe Use the attached power cord only If the outlet is a 3 pronged type or other have an electrician install a new outlet The new air conditioner system should be on it s own 220V Plug into Only 220V or 220V 240V AC Outlet circuit
19. ess the MODE button until the Fan indicator The fan will operate on high speed NATURAL The fan will randomly cycle through the speeds simulating a breeze turn the unit on the On LED will light on the indoor appears in the display No allowance setting unit and ON will light in the remote display temperature 3 To select a fan speed press the FAN SPEED button CPx until the desired speed appears in the display see below FAN qi FAN SPEED FAN SPEEDS me The fan will operate on low speed NOTE T June spots ems Uc ecce If NATURAL is selected the NATURAL indicator on the indoor unit will light TO SET UNIT TO DEHUMIDIFIER MODE Select this mode when there is high humidity To select follow the procedures below 1 Press the ON OFF button on the remote control to turn the unit on the On LED will light on the indoor unit and ON will light in the remote display 2 Press the MODE button until the Dehumidifier indica tor E appears in the display MODE 3 Using the TEMP WV or A buttons set the desired tem perature The desired temperature can be changed up to 32 C and down to 18 C DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 9 5 17 TO SET UNIT TO HEAT MODE ONLY HEAT PUMP MODEL To setthe unit to heat the room to a desired temperature follow the procedures below 1 Press the O
20. hall be installed in accordance with the nationed wiring regulation The equipment fulfills the requirements in EN 61 000 3 11 and is subject to conditional connection to the mains t may be connected in consultation with the supply authority The equipment may only be connected to a mains supply with a system impedance of less than 0 3 ohm The system impedance in the interface point may be obtained from the supply authority If the mains supply has a higher system impedance short voltage dips may appear when the equipment is started or during opera tion This may influence or disturb the operation of other apparatuses e g flickering lamps especially those connected to the same supply mains DS B F1 54 F 1 83 1 83L LH PH AH 2003 12 9 2 47 AM 4 4 C 5 LOCATION OF CONTROLS INDOOR UNIT Electric Dust Collector Air clean Plasma Removes small dust Deodorizing Filter generates ions Removes bad smells from the air Indoor Cover Air Cleaning Filters Removes dust and prohibits germs Fan Direction Up Down AIR OUT Fan Direction Left Right CAA LCD Remote Controller OUTDOOR UNIT AIR OUT Emergency Remote Switch Slide to select the desired position and O2 Hose Cover AH Model Only Sensor Wire LH PH AH Model Only Remote Sensor Indicators Indicate the AC setting Power Plug
21. ing the unit be very careful and get help as the units are very heavy Be careful of sharp edges on the units also Precautions When Installing When installing in a ceiling or wall make sure the ceiling wall is strong enough to hold the unit s weight A frame may be necessary for added support When installing in a room make sure the tubes are well insulat ed to protect the walls and furniture from sweating of the tubes When installing in moist or uneven locations make sure to use a raised level concrete pad or concrete blocks to provide a level solid foundation for the outdoor unit this prevents water damage and vibration When installing in an area of high winds make sure to securely anchor the outdoor unit down with bolts and a metal frame When Connecting Refrigerant Tubing Keep all tubing as short as possible Use the flare method for connecting tubing Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before connecting them then tighten making sure not to overtighten Check the tubes carefully for leaks before starting the test run When Servicing Make sure the power is off and the unit is unplugged before open ing the unit to troubleshoot or repair electrical parts and wiring Keep your fingers and clothing away from any moving parts Clean up the sight after you finish making sure no metal scraps and wiring are left in the unit The Air conditioner s
22. the bracket and into the wall Level the remote bracket and insert the other screw into the bottom hole Insert the remote controller when not using it 14 wi DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 25 CARE AND MAINTENAN CE N warning Make sure the AC cord is unplugged and the unit is off before cleaning Do not use water on the unit to clean it This is a shock hazard and the unit can be damaged Clean the casing and front of the indoor unit with a vacuum brush or wipe with a clean damp cloth NEVER USE Solvents harsh chemicals or hot water to clean the unit Some metal edges on the unit are sharp Be careful when cleaning or handling Internal parts in the outdoor unit may need cleaning or routine maintenance from time to time Consult your local ser vice center for more details AFTER THE SEASON Operate the fan then dry the indoor unit Shut off the indoor unit and then unplug it from the wall Clean the air filters Cover the outdoor unit with the supplied cover this is very important to protect this unit BEFORE THE SEASON Make sure the air filters are clean Make sure the inlet and outlet on the indoor and outdoor units are not blocked by obstructions Make sure the unit is grounded Consult a serviceman for help PRECAUTIONS Do not use this unit for animal or plant storage Ina lightning or thunder storm imm
23. y 2 Press the MODE button to select the desired mode MODE 3 Press the FAN DIR button to select the fan direction See chart below for detailed information on each of the two settings FAN DIR AV v The air will flow up FAN DIR lt gt i p gt The air will flow left First Press and down First Press and right Second Nermalardirecion Second Normal air direction Press Press DSB 15 SERIES DS B F154 F183 183L LH PH AH 2003 12 9 2 47 AM 20 TO SET THE ON TIMER MODE This unit can be set to automatically turn on after a predetermined amount of hours up to 24 in the order of 0 5 1 1 5 2 2 5 3 3 5 4 5 6 8 10 12 16 20 24 Mode please press ENTER CANCEL again 1 Press the ON OFF button of timer on the remote control to set the on timer mode HOUR and ON on the remote display will be displayed and TIMER will be flicked When you increase to press ON OFF you will get desired time Then if pressing ENTER CANCEL button ON TIMER Mode will be started If you want to stop ON TIMER 2 While the unit is off press the TIMER ON button the display will light waiting input for the timer but the actual unit will not turn on r TIMER 4 eum D ON OFF ENTER CANCEL e a HOUR IIL tt QN TIMERS 3 Repeatedly press the TIMER ON button until
Download Pdf Manuals
Related Search
Related Contents
contributo da gestão da manutenção para a competitividade das John Witzke Tech Advisor & Historian W72 Performance Copyright © All rights reserved.
Failed to retrieve file