Home

D-Link DSL-522T User's Manual

1. src MAC src Port Dest MAC Dest Port Protocol Mode 00 00 00 00 00 0 ANY _ 00 00 00 00 00 0 AN Y___W PPPoE Session Y Deny sl vago Apply Cancel Help Src MAC Src Port Dest MAC Dest Port Protocol Mode Delete Bridge Filters window To add a bridge filter rule check Enable Bridge Filters type in a Source MAC a Destination MAC or both in the entry fields you may opt to limit filtering to only the Ethernet and click the Apply button To remove a bridge filter from the table in the bottom half of the window click the corresponding trashcan icon Remember to save the configuration changes The protocols that may be specifically allowed or denied to pass through the WAN interface are the following IPv4 IPv6 RARP PPPoE Discovery and PPPoE Session 50 DSL 522T ADSL Router User Guide Static Routing Use Static Routing to specify a route used for data traffic within your Ethernet LAN or to route data on the WAN This is used to specify that all packets destined for a particular network or subnet use a predetermined gateway Tools Status Help IF Routes are Used to define gateways and hops used to route data traffic Most users will not need to use this feature as the previous gateway and LAN IP settings on your host computers Should be sufficient Destination Netmask 255 255 255 1 Gateway Connection o oO O Apply Cancel Help Destination Netmask Interface Routing Table window To a
2. DSL 522T ADSL Router User Guide May 2006 ESL522TEU A1G Table Of Contents BEFORE YOU STAR EE IV instalation e e TE iv SEW Wizard cta iv PACKING LIS E iv JE UE ele Notes sia a V Installing the USB Drivel aaa dad vii INTRODUCTION o aia 1 Router Description and Operallon SE 1 Router Features ice crio 2 teil NEE 3 Rear Panel ee ne e Saa 4 HARDWARE INSTALLATION courier 5 POWER ON EE 5 Factory Reset Button ati ae a a ate SOE etait earlier ec cae ial tel ate 5 Network Connections coca av arancel 6 BASIC ROUTER CONFIGURATION s ssssssssssesesscsssessesssessesesesessesssessescseseesesesessesesesaeens 7 Computer EE id ee 7 Access the Configuration dE Te TEE 8 Beie Briefe ein Ir AGC iia iia 8 Gontiqure the E TEE 9 o EE 10 WAN eegene 18 Bndge Mode EE 18 Dynamic IF Adre SS or Di a chemin 20 SAUC IPF Addes St a A A A E ee a eee 23 ERROR E et 26 LAN usa 31 DAS Pi ada 32 DNS i acer ucuaesauecune sis ceskcagnceemecasionauwaanieacueceeasunnee maumuectseuicesaenenae 36 By FAG DN Sat As 37 SaVe SEWiInGs NA RODOOL E 38 Multiple MIER ee Ee 39 ADVANCED ROUTER MANAGEMENT isis nn 41 A sti E eco acd E nad cde tide eta TEET EE T inane 42 Aleng Ee 43 PAS A A A adenine 46 SS EE 47 A EEN 48 A O eet 52 URS Walla AO lao Loa dico 93 A A A A S DETE 54 A E A O 55 Een 56 LN Sue sete ee A e 57 FOOLS ct iii oia 58 Change Systemi Pass Wo iii is 59 Remote Web Management and Remote Telnet Access 59 HE DU Remote ee DEE 61 Sa
3. Single IP an IP Range or Any IP from the pull down menu The Source Port is the TCP UDP port on either the LAN or WAN depending on if you are configuring an Outbound or Inbound Filter rule Select one of the following options from the pull down menu to define Any Port Single Port Port Range or Safe Range ports above 1024 Source Port The Destination Port is the TCP UDP port on either the LAN or WAN depending on if you are configuring an Outbound or Inbound Filter rule Select one of the following options from the pull down menu to define a Any Port Single Port Port Range or Safe Range ports above 1024 Destination Port Select the transport protocol TCP UDP or TCP UDP that will be used for Protocol i the filter rule Select to Allow or Deny transport of the data packets according to the Action criteria defined in the rule Packets that are allowed are routed to their destination packets that are denied are blocked 49 DSL 522T ADSL Router User Guide Bridge Filters Bridge filters are used to block or allow various types of packets through the WAN interface This may be done for security or to improve network efficiency The rules are configured for individual devices based on MAC address Filter rules can be set up for source destination or both You can set up filter rules and disable the entire set of rules without loosing the rules that have been configured Home Advanced Status Help Enable Bridge Filters
4. Static IP 4 Static IF 5 Enter MAC address format as wow Le 00 0C 6E D5 11 22 and IP address format as Wu A wt Wu d e 192 168 1 2 Apply Cancel Help Mumber IF Address MAC Address 1 192 168 1 2 DHCP Settings window 32 DSL 522T ADSL Router User Guide To display the DHCP Settings window click the DHCP button in the Home directory Any active DHCP Clients appear at the bottom of the window in the DHCP Clients List The IP address and MAC address for active DHCP clients are displayed in the list The two options for DHCP service are as follows You may use the Router as a DHCP server for your LAN You can disable DHCP service and manually configure IP settings for workstations You may also configure DNS settings for the LAN when using the Router in DHCP mode In Auto DNS Mode the Router will automatically relay DNS settings to properly configured DHCP clients To manually enter DNS IP addresses select the Manual DNS Mode option and type in a Primary and Secondary DNS IP Address in the field provided The manually configured DNS settings will be supplied to clients that are configured to request them from the Router Follow the instructions below according to which of the above DHCP options you want to use When you have configured the DHCP Settings as you want them click the Apply button to commit the new settings Use the Router for DHCP To use the built in DHCP server click to select the DHCP Server option if
5. TCP IP protocol installed If you have an Ethernet port on your computer it probably already has TCP IP protocol installed If you are using Windows XP the TCP IP is enabled by default for standard installations Instructions for configuring your computer to receive IP settings from the Router are provided in Appendix B on page 74 For computers running non Windows operating systems follow the instructions for your OS that configure the system to receive an IP address from the Router that is configure the system to be a DHCP client A If you are not sure how to configure your Windows computer to be a DHCP client see Configuring IP Settings on Your Computer begiining on page 74 DSL 522T ADSL Router User Guide Access the Configuration Manager In order to make sure your computer s IP settings allow it to communicate with the Router it is advisable to configure your system be a DHCP client that is it will get IP settings from the Router Appendix B describes how to configure different Windows operating systems to Obtain IP settings automatically Be sure that the web browser on your computer is not configured to use a proxy server in the Internet settings In Windows Internet Explorer you can check if a proxy server is enabled using the following procedure 1 In Windows click on the Start button and choose Control Panel 2 In the Control Panel window click on the Network and Internet Options icon A 3 In the Network and Inte
6. The PCR is inversely related to the time interval between ATM E cells It is specified for all three service categories UBR CBR and VBR in Kbps Sustainable Cell Rate The SCR is defined for the VBR service category This is SCR the rate that can be sustained for bursty on off traffic sources It is a function of Maximum Burst Size MBS and the time interval between cells 29 ATM VC Settings DSL 522T ADSL Router User Guide ATM VC settings can be configured for all connection types in the WAN configuration menu of the Home directory PL VPI VU Virtual Circuit WAN Setting Advanced Tools Status Bridge Mode ATM VC Settings in WAN Settings window The table below describes the ATM VC settings used to configure a PPPoE or PPPoA connection for an ADSL account ATM VC Parameters Virtual Circuit Description The Router supports using up to eight multiple virtual connections This window allows the user to configure WAN settings for all the available connections see instructions below on how to set up Multiple Virtual Connections Use the PVC drop down menu to select the connection PvcO to Pvc7 you want to configure Since most users will use only a single connection the default setting PvcO can be used for any changes made to the WAN settings The Virtual Path Identifier is used with the VCI to define a dedicated circuit on the ATM network portion of the connection to the I
7. used Internet applications If you plan to change QoS or traffic parameters contact your ISP or network services provider for information on what types of adjustment are available or possible for your account Your ISP may not support the class of service you want to use To adjust ATM QoS parameters select one of the Service Categories listed here and type in the PCR value in the entry field below For the VBR service category an additional parameter SCR must also be defined Service Category UBR Unspecified Bit Rate this is the default category used for general purpose Internet traffic where normal levels of packet loss and delay are acceptable For some applications or for multiple connection accounts it may be desirable to specify the PCR CBR Constant Bit Rate usually used in circumstances where very low packet loss and very low Cell Delay Variable CDV are desirable VBR nt Real time Variable Bit Rate This models bursty traffic with specified peak and sustainable rates Please note that when VBR rt is specified both PCR and SCR are required by ATM standards VBR nrt Non real time Variable Bit Rate usually used when network traffic is characterized by bursts of packets at variable intervals and some moderate packet loss and delay is acceptable This category is typically used for audio and video applications such as teleconferencing The network must support QoS Class 2 to use VBR nrt Peak Cell Rate
8. Filters windows This window can be accessed directly by clicking on the LAN Clients button in the Advanced tab In order to use these advanced features it is necessary to have IP addresses available for configuration If there are no IP addresses listed in the LAN Clients window you will not be able to access the Virtual Server window Use the LAN Clients window to add or delete static IP addresses for the advanced functions mentioned above or to Reserve a Dynamically assigned IP address for an advanced function Dynamically assigned IP addresses will only be listed if DHCP is enabled on the Router F Home f Adwancec Tools Status Hel IP Address 192 16813 Host Name fido Valid IP Range 192 168 1 2 192 168 1 254 Delete IF Address Host Hames Type F 192 168 1 2 Static Reserve IPF Address Host Names Type C 192 168 1 2 wangka Dynamic Oo O OO Apply Cancel Help LAN Clients window To add a static IP address to the list of available IP addresses type an IP address that falls within the range a available IP addresses and click on the Add button In the example above available addresses range from 1 0 0 1 to 223 255 255 254 Any addresses added will appear in the list of Static Addresses available for advanced configuration To delete an IP address from the list of Static Addresses click the Delete box for the address or addresses you want to eliminate and click on the Apply button Dynamically assigned IP addresses ma
9. Folders E Address ES Network and Internet Connection See Also SS My Network Places O Printers and Other Hardware Y Remote Desktop Bp Phone and Modem Options Troubleshooters 2 Home or Small Office Networking Click Network Connections Diagnostics 4 Network Connections Q sa 2 Ki JO searc File Edit view Favorites Tools Advanced Help S Network and Internet Connections Pick a task Set up or change your Internet connection Create a connection to the network at your workplace Set up or change your home or small office network or pick a Control Panel icon a Network Connection Internet Uptions In the Network Connections window right click on Local Area Connection then click Properties Seles La h ey Folders EI Address 43 Network Connections JCE Name Type Status Device Na Network Tasks LAN or High Speed Internet Other Places Local Area Connection Disable or High Speed Inter Enabled D Link DFE E ES e Bridge Connections Right click on the Local Area oe Connection icon and select the Las Properties option from the pull down menu IN KI fe DSL 522T ADSL Router User Guide 5 In the General tab of the Local Area Connection Properties window highlight Internet Protocol TCP IP under This connection uses the following items by clicking on it once Click on the Properties button Local Area Con
10. Guide Miscellaneous Configuration To perform a statndard Ping test for network connectivity click the Misc window button in the Tools directory to view the Miscellaneous Configuration window Home Advanced sol 1 Status Help There are additional tools and features of the DSL 522T Ping IP Address 192 168 1 1 Lang Ping Result IGMP Proxy Puco Disabled Enabled 0 0 Apply Cancel Help Miscellaneous Configuration window Other functions available in Miscellaneous Configuration menu are a Ping test and IGMP enable disable Ping Test The Ping test functions on the WAN and LAN interfaces Type the IP address you want to check in the space provided and click the Ping button Read the Ping test result in the space immediately below IGMP Proxy The Miscellaneous Configuration window also allows you to enable IGMP forwarding This is disabled by default This setting will not allow IGMP Internet Group Management Protocol packets to be forwarded to the LAN IGMP is used to manage multicasting on TCP IP networks most users will not need to enable this Some ISPs use IGMP to perform remote configuration for client devices such as the Router If you are unsure please check with your ISP To enable IGMP service to the LAN interface select Enabled and click the Apply button 64 DSL 522T ADSL Router User Guide Diagnostic Test The Diagnostic Test window is used to test connectivity of the Router A Ping test ma
11. VCs List The PVCs current settings appear above in the entry fields of the ATM VC Setting window Configure the appropriate settings and click the Apply button to put the new settings into effect 57 Tools DSL 522T ADSL Router User Guide Click the Tools tab to reveal the window buttons for various functions located in this directory The Administrator Settings window is the first item in the Tools directory This window is used to change the system password used to access the web manager to save or load Router configuration settings and to restore default settings The functions in this and the other Tools windows are described below Remotelog System Miscellaneous Logout DSL 522T Home Advanced There are two accounts that can access the DSL 527T s Vweb Management interface Administrator The Login Name is admin Select D Modify admin password Modify user password Modify admin password New Password Confirm Password WebPort a0 Change the port number of login web Modify user password New Password Confirm Password State C Enabled Disabled IP Address Hetmask State C Enabled Disabled IP Address 0000 Hetmask State Enabled C Disabled IP Address 7 7 77 Metmask 0 0 0 0 Administrator Settings window 58 DSL 522T ADSL Router User Guide Change System Password Click the Admin button in the Tools directory to view the the Administrator Settings menu Under the Administr
12. are now sold with an Ethernet port already installed Likewise most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment If your computer does not have an Ethernet port and you do not wish to use a USB connection you must install an Ethernet NIC adapter before you can use the Router If you must install an adapter follow the installation instructions that come with the Ethernet NIC adapter Additional Software For a bridged connection the information needed to make and maintain the Internet connection is stored on another computer or gateway device using PPP client or similar third party client software not in the Router itself If your ADSL service is delivered through a PPPoE PPPoA or Static IP connection the information needed to establish and maintain the Internet connection can be stored in the Router In this case it is not necessary to install software on your computer It may however be necessary to change some settings in the device including account information used to identify and verify the connection A If you plan to use the DSL 522T s USB port to connect to your computer do Note not connect the USB cable to the Router until you have finished all of the steps to install the USB driver and your computer has restarted DSL 522T ADSL Router User Guide Information you will need from your ADSL service provider This is the Username used to log on to your ADSL service Record info her
13. button to place the rule in the Applied Rules list of port forwarding that are actively applied to the client The Available Rules can be applied to a single client IP address That is it is not possible to use an applied rule for multiple IP addresses on the LAN 44 DSL 522T ADSL Router User Guide Custom Forwarding Rules The User category for port forwarding is used to set up customized port forwarding rules To set up custom TCP or UDP port forwarding rules follow these steps 1 Select the User category and click the Add button located below the Available Rules list This will change the window to look like the window below Rule Name Protocol JCP Port Start Port Map O o Apply Cancel Protocol Port Start Port End Port Map 2 Type a Rule Name in the space provided 3 Select the port Protocol from the pull down menu you may select TCP UDP or both TCP UDP 4 Configure a range of ports for forwarding Type the lowest numbered port in the range in the Port Start space Type the highest numbered port in the Port End space For a single port just enter the same number in both spaces Type a number for the Port Map in the space provided Click the Apply button to create the new rule The new rule will appear listed in the table of custom port forwarding rules 45 DSL 522T ADSL Router User Guide LAN Clients The LAN Clients window is used when establishing port forwarding rules in the Virtual Server and
14. changed to suit any IP address scheme the user desires This address will be the base IP address used for DHCP service on the LAN when DHCP is enabled This is the subnet mask used by the DSL 522T and will be used throughout your LAN The default subnet mask is 255 255 255 0 This can be changed later LAN Subnet Mask for the DSL 522T Information you will need about your LAN or computer If your computer has an Ethernet NIC you can Record info here connect the DSL 522T to this Ethernet port using an Ethernet NIC Ethernet cable You can also use the Ethernet ports on the DSL 522T to connect to other computer or Ethernet devices Your DSL 522T ADSL Router is configured by default to be a DHCP server This means that it can assign an IP address subnet mask and a default gateway address to computers on your LAN The DHCP Client status default range of IP addresses the DSL 522T will assign are from 192 168 1 2 to 192 168 1 254 Your computer or computers needs to be configured to Obtain an IP address automatically that is they need to be configured as DHCP clients It is recommended that your collect and record this information here or in some other secure place in case you have to re configure your ADSL connection in the future Once you have the above information you are ready to setup and configure your DSL 522T ADSL Router Installing the USB Driver IMPORTANT Do not connect the USB cable to your PC before comple
15. changes and then close the Control Panel Your computer is now ready to use the Router s DHCP server 71 DSL 522T ADSL Router User Guide Windows 95 and Windows 98 First check for the IP protocol and if necessary install it 1 T In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network icon The Network dialog box displays with a list of currently installed network components If the list includes TCP IP and then the protocol has already been enabled skip to Configure IP Information Windows 95 98 If TCP IP does not display as an installed component click Add The Select Network Component Type dialog box displays Select Protocol and then click Add The Select Network Protocol dialog box displays Click on Microsoft in the Manufacturers list box and then click TCP IP in the Network Protocols list box Click OK to return to the Network dialog box and then click OK again You may be prompted to install files from your Windows 95 98 installation CD Follow the instructions to install the files Click OK to restart the PC and complete the TCP IP installation Configure Windows 95 and Windows 98 for DHCP 1 E E e Open the Control Panel window and then click the Network icon Select the network component labeled TCP IP and then click Properties If you have multiple TCP IP listings select the listing associated with your network card or ad
16. configuration click the System button to view the System Settings window pictured here Status Help Home Advanced The current system settings can be saved as a file onto the local hard drive Save Settings To Local Hard Drive GAVE Load settings From Local Hard Drive Browse Mote The system has to be restarted after the configuration is restored Save Settings and Reboot the System Save and Reboot Restore To Factory Default Settings System Settings window To save the settings you have configured click the Save and Reboot button under Save Settings and Reboot the System 38 DSL 522T ADSL Router User Guide Multiple Virtual Connections The Router supports multiple virtual connections Up to eight PVCs to eight separate destinations can be created and operated simultaneously utilizing the same bandwidth Additional PVC connections can be added for various purposes For example you may want to establish a private connection to remote office in order to create an extended LAN or setup a server on a separate connection Provisioning for additional PVC profiles must be done through your telecommunications services provider Extended LAN operations employing multiple virtual connections require ADSL routers or modems at the remote site for a successful connection Contact your ISP or telecommunications service provider if you are interested in setting up multiple virtual connections After the necessary
17. filter 80 DSL 522T ADSL Router User Guide Three Port Filter Another style of filter is installed at the same point where the Router connects to the telephone line Only a single filter is required The connection ports are typically labeled as follows Line This port connects to the wall jack ADSL This port connects to the Router Phone This port connects to a telephone or other telephone device The diagram below illustrates the proper use of this style of filter Make certain the lines are properly connected If you are unable to hear a dial tone with the telephone check the connections to make sure they are securely attached and connected to the correct port Phone Jack J f Splitter ADSL Device 3 port Filter 81 U S A 17595 Mt Herrmann Street Fountain Valley CA 92708 TEL 1 800 326 1688 URL www dlink com Canada 2180 Winston Park Drive Oakville Ontario L6H 5W1 Canada TEL 1 905 8295033 FAX 1 905 8295223 URL www dlink ca Europe U K 4 Floor Merit House Edgware Road Colindale London NW9 5AB U K TEL 44 20 8731 5555 FAX 44 20 8731 5511 URL www dlink co uk Germany Schwalbacher Strasse 74 D 65760 Eschborn Germany TEL 49 6196 77990 FAX 49 6196 7799300 URL www dlink de France No 2 all ee de la Fresnerie 78330 Fontenay le Fleury France TEL 33 1 30238688 FAX 33 1 30238689 URL www dlink fr Netherlands Weena 290 3012 NJ Rotterdam Netherlan
18. gateway for instance Default Routing This allows you to choose a default path for incoming data packets for which the destination address is unknown This is particularly useful when if the Router functions as the sole connection to the Internet ATM Asynchronous Transfer Mode The DSL 522T supports Bridged Ethernet over ATM RFC1483 IP over ATM RFC1577 and PPP over ATM RFC 2364 Precise ATM Traffic Shaping Traffic shaping is a method of controlling the flow rate of ATM data cells This function helps to establish the Quality of Service for ATM data transfer G hs Auto handshake This allows the Router to automatically choose either the G lite or G dmt ADSL connection standards High Performance Very high rates of data transfer are possible with the Router Up to 8 Mbps downstream bit rate using the G dmt standard Full Network Management The DSL 522T incorporates SNMP Simple Network Management Protocol support for web based management and text based network management via an RS 232 or Telnet connection Telnet Connection The Telnet enables a network manager to access the Routers management software remotely Easy Installation The DSL 522T uses a web based graphical user interface program for convenient management access and easy set up Any common web browser software can be used to manage the Router DSL 522T ADSL Router User Guide Front Panel Display Place the Router in a location that
19. it is not already selected The IP Address Pool settings can be adjusted The Starting IP Address is the lowest available IP address default 192 168 1 2 If you change the IP address of the Router this will change automatically to be 1 more that the IP address of the Router The Ending IP Address is the highest IP address number in the pool Type in the Lease Time in the entry field provided This is the amount of time in seconds that a workstation is allowed to reserve an IP address in the pool if the workstation is disconnected from the network or powered off Disable the DHCP Server To disable DHCP click to select the No DHCP option and click on the Apply button Choosing this option requires that workstations on the local network must be configured manually or use another DHCP server to obtain IP settings If you configure IP settings manually make sure to use IP addresses in the subnet of the Router You will need to use the Router s IP address as the Default Gateway for the workstation in order to provide Internet access 33 DSL 522T ADSL Router User Guide The device can be setup as a DHCP Server to distribute IP addresses to the LAN network Choose this option The IP address must be manually assigned at each device connected to DSL 52 T No DHCP Choose this option to setup as a QHCP server to distribute IP 12 DACP Server addresses to the LAN network 420 Oo Apply Cancel Help DHCP Settings window with D
20. permits an easy view of the LED indicators on the front panel The LED indicators on the front panel include Power Status ADSL Ethernet and USB The ADSL Ethernet and USB indicators monitor link status and activity Link Act ADSL2 Router ADSL Link Act Ethernet Link Act USB Link Act Power Status ADSL Ethernet DSL 522T Link Act Link Act Link Act Steady green light indicates the unit is powered on When the device is powered off this remains dark Lights steady green during power on self test POST Once the connection status has been settled the light will blink green If the indicator lights steady green after the POST the system has failed and the device should be rebooted Steady green light indicates a valid ADSL connection This will light after the ADSL negotiation process has been settled A blinking green light indicates activity on the WAN ADSL interface A solid green light indicates a valid link on startup This light will blink when there is activity currently on the Ethernet port Steady green light indicates a valid USB connection A blinking green light indicates activity on the USB interface DSL 522T ADSL Router User Guide Rear Panel Connections All cable connections to the Router are made at the rear panel Connect the power adapter here to power on the Router Use the Reset button to restore the settings to the factory default values in the next chapter for instructions on usi
21. settings to non volatile memory 61 DSL 522T ADSL Router User Guide Save or Load Configuration File Once you have configured the Router to your satisfaction it is a good idea to back up the configuration file to your computer To save the current configuration settings to your computer click the System button in the Tools directory to display the System Settings window Click the Save button to Save Settings to Local Hard Drive You will be prompted to select a location on your computer to put the file The file type is xml HTML and may be named anything you wish To load a previously saved configuration file click the Browse button and locate the file on your computer Click the Load button to Load Settings From Local Hard Drive Confirm that you want to load the file when prompted and the process is completed automatically The Router will reboot and begin operating with the configuration settings that have just been loaded Home Ad vanced Tools Status Help The current system settings can be saved as a file onto the local hard drive Save Settings To Local Hard Drive Saya Load Settings From Local Hard Drive ss Mote The system has to be restarted after the configuration is restored Save Settings and Reboot the System save and Reboot Restore To Factory Default Settings Restore System Settings window Restore Factory Default Settings To reset the Router to its factory default settings click
22. the Restore button You will be prompted to confirm your decision to reset the Router The Router will reboot with the factory default settings including IP settings 192 168 1 1 and Administrator password admin 62 DSL 522T ADSL Router User Guide Firmware Upgrade A Performing a Firmware Upgrade can sometimes change the configuration settings Be Note sure to back up the Router s configuration settings before upgrading the firmware Use the Firmware Upgrade window to load the latest firmware for the device Note that the device configuration settings may return to the factory default settings so make sure you save the configuration settings with the System Settings window described above Home _ Advanced Tool Status There may be new firmware for your DSL 5227 to improve functionality and performance To Upgrade the firmware locate the upgrade file on the local hard drive with the Browse bution Once vou have found the file to be used click the Apply button below to start the firmware upgrade Current Firmware Version 3018017101 EU 20051219 Browse Mote The system has to be restarted after the firmware Upgrade Oo O O Apply Cancel Help Firmware Upgrade window To upgrade firmware type in the name and path of the file or click on the Browse button to search for the file Click the Apply button to begin copying the file The file will load and restart the Router automatically 63 DSL 522T ADSL Router User
23. the Router is configured to use Static IP Address assignment for the WAN connection you must manually assign a global IP Address Subnet Mask and Gateway IP Address used for the WAN connection Most users will also need to configure DNS server IP settings in the DNS Configuration window see below Follow the instruction below to configure the Router to use Static IP Address assignment for the WAN connection To configure a Static IP Address connection perform the steps listed below Some of the settings do not need to be changed the first time the device is set up but can be changed later if you choose See the table below for a description of all the settings available in this window Advanced PI WI Virtual Circuit WAN Setting connection Type IP Address subnet Mack Gateway Address ARP Serer Address Primary ONS Address Secondary ONS Address WT MAT Firewall Serice Category PER SCR Tools Status buch zi B E Enabled Static IP Address 1483 Routed IF LLC 0000 1400 bytes Enabled y Enabled vw UBR sl kbps a kbps v Y 0 Apply Cancel Help WAN Settings window Static IP 23 DSL 522T ADSL Router User Guide To configure a Static IP type connection for the WAN follow these steps 1 2 9 Choose the Static IP Address option from the WAN Settings pull down menu Under the ATM VC Settings at the top of the window should not be changed unles
24. 522T ADSL Router User Guide Using the Setup Wizard Choose Time Zone Choose the time zone you are in from the pull down menu and click Next This sets the system time used for the Router If you wish to return to the previous window during the setup process click the Back button A DSL 5227 Microsoft Internet Explorer Choose Time Zone Select the appropriate time zone for your location and click Next to continue ahd 02 00 Athens Istanbul Minsk Exit Back 11 DSL 522T ADSL Router User Guide Using the Setup Wizard Choose Connection Type Now select the Connection Type used for the Internet connection Your ISP has given this information to you The connection types available for Multi User Mode are PPPoE PPPoA Dynamic IP Address Static IP Address and Bridge Mode Each connection type has different settings that are configured in the next Setup Wizard pop up window 2 DSL 5227 Microsoft Internet Explorer Select Internet Connection Type WAN Select the connection type to connectto your ISP Click Next to continue PPPoEIPPPos Choose this option if your ISP uses PPPoE PPPoa For most DSL users Choose this option to obtain an ID address O Dynamic IP Address A automatically from your ISP Static IP Address Choose this option to set static IP information provided to you by your ISP O Bridge Mode Choose this option if your ISP uses Bridge Mode 9 0 Back Next Exit Se
25. 9 9715601 URL www dlink co il LatinAmerica Isidora Goyeechea 2934 Ofcina 702 Las Condes Santiago Chile TEL 56 2 232 3185 FAX 56 2 232 0923 URL www dlink cl Brazil Av das Nacoes Unidas 11857 14 andar cj 141 142 Brooklin Novo Sao Paulo SP Brazil CEP 04578 000 Zip Code TEL 55 11 21859300 FAX 55 11 21859322 URL www dlinkbrasil com br South Africa Einstein Park Il Block B 102 106 Witch Hazel Avenue Highveld Technopark Centurion Gauteng Republic of South Africa TEL 27 12 665 2165 FAX 27 12 665 2186 URL www d link co za Russia Grafsky per 14 floor 6 Moscow 129626 Russia TEL 7 095 744 0099 FAX 7 095 744 0099 350 URL www dlink ru China No 202 C1 Building Huitong Office Park No 71 Jianguo Road Chaoyang District Beijing 100025 China TEL 86 10 58635800 FAX 86 10 58635799 URL www dlink com cn Taiwan 2F No 119 Pao Chung Rd Hsin Tien Taipei Taiwan TEL 886 2 2910 2626 FAX 886 2 2910 1515 URL www dlinktw com tw Headquarters 2F No 233 2 Pao Chiao Rd Hsin Tien Taipei Taiwan TEL 886 2 2916 1600 FAX 886 2 2914 6299 URL www dlink com tw
26. CP UDP ports The pre configured rules include those listed in the table here Category Available Rules Games Alien vs Predator Asheron s Call Dark Rein 2 Delta Force Doom Dune 2000 DirectX 7 8 Games EliteForce EverQuest Fighter Ace ll Half Life Heretic Il Hexen II Kali Motorhead MSN Gaming Zone Myth The Fallen Lords Need for Speed Porsche Need for Speed 3 Outlaws Rainbow 6 Rogue Spear Starcraft Tiberian Sun Ultima Unreal Tournament Quake 3 Server Quake 2 Server and Unreal Server VPN IPSec L2TP and PPTP Audio Video Net2Phone Netmeeting and QuickTime 4 Server Applications VNC Win2k Terminal PC Anywhere Netbios RemoteAnything Radmin LapLink CarbonCopy and Gnutella Servers Web FTP Telnet DNS LDAP NNTP SMTP POP 2 POP 3 IMAP IRC Lotus and Remotely Possible User Use this to set up custom TCP UDP port rules To configure a new port forwarding rule for any of the pre configured rules follow these steps 1 Select the WAN connection you want to use for the new rule from the Connection pull down menu 2 Select a LAN IP from the available client IP addresses listed in the pull down menu or create a New IP by clicking the button This brings up the LAN Clients window see next section 3 Select the Category of the rule you are creating The Available Rules for the category appear in a list 4 Highlight to select the Available Rule you want to apply 5 Click on the Add gt
27. Configure Windows ME for DHCP ls 2 3 4 5 In the Control Panel window double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Network icon and then select Properties In the Network Properties dialog box select TCP IP and then click Properties In the TCP IP Settings dialog box click the Obtain and IP address automatically option Double click OK twice to confirm and save your changes and then close the Control Panel Your computer is now ready to use the Router s DHCP server Windows NT 4 0 Workstations First check for the IP protocol and if necessary install it 1 2 3 4 en 8 In the Windows NT task bar click the Start button point to Settings and then click Control Panel In the Control Panel window double click the Network icon In the Network dialog box click the Protocols tab The Protocols tab displays a list of currently installed network protocols If the list includes TCP IP then the protocol has already been enabled Skip to Configure IP Information If TCP IP does not display as an installed component click Add In the Select Network Protocol dialog box select TCP IP and then click OK You may be prompted to install files from your Windows NT installation CD or other media Follow the instructions to install the files After all files are installed a window displays to inform you that a TCP IP service called DHC
28. HCP disabled Internet Protocol TCP IP Properties A General You can get IF settings assigned automatically d your network supports this capability Othermize you need to ask your network administrator for the appropriate IP settings To manually configure IP settings on Windows workstations open Obtain an IP address automatically the TCP IP Properties menu and Use the following IP address select the Use the following IP Paise CELLIE address option You will need to supply the IP addres Subnet Note mask and Defualt gateway use Default gateway IP address of DSL 522T for each workstation The example INS si l ER here also uses manually 2 Use the following DNS server addresses configured DNS settings Preferred ONS server 168 Subnet mask Alternate ONS server k 34 DSL 522T ADSL Router User Guide Static IP on LAN If the Router has the DHCP server enabled it is possible to permanently assign IP addresses to workstations specified by their MAC address Up to five IP addresses may be assigned to five different devices This will take the chosen IP address used out of the available addresses in the dynamic IP address pool and give a permanent lease time for the IP address to the selected device To assign an IP address that will not age out type in the MAC Address of the device and its static IP Address in the spaces provided Use the format 00 00 00 00 00 00 for the MAC address and the stan
29. Mack 259 255 259 0 v Y 0 Apply Cancel Help Management IP window To change the LAN IP Address or Subnet Mask type in the desired values and click the Apply button Your web browser should automatically be redirected to the new IP address You will asked to login again to the Router s web manager 31 DSL 522T ADSL Router User Guide DHCP The DHCP server is enabled by default for the Router s Ethernet LAN interface DHCP service will supply IP settings to workstations configured to automatically obtain IP settings that are connected to the Router though the Ethernet port When the Router is used for DHCP it becomes the default gateway for DHCP client connected to it Keep in mind that if you change the IP address of the Router the range of IP addresses in the pool used for DHCP on the LAN will also be changed The IP address pool can be up to 253 IP addresses Advanced Tools Status The device can be setup as a DHCP Server to distribute IP addresses to the LAN network Choose this option The IF address must be manually assigned at EN 4 Mo DHCP each device connected to OSL 4520T Choose this option to setup as a DHCP server to distribute IF DHCP Server addresses to the LAN network Starting IP Address 192 168 1 2 Ending IP Address 192 168 1 254 Lease Time S600 seconds DNS Mode Auto Manual Primary ONS secondary ONS static IP Assignment MAC address IP address Static IP1 Static IP 2 Static IP 3
30. O Enabled O Disabled NMAP FIN URG PSH attack Xmas Tree attack Null Scan attack SYNIRST attack SYNIFIN attack The following services can be blocked based on your specific need C Ping from External Network Telnet from External Network K FTF from External Network K DNS from External Network K IKE from External Network K RIP from External Network K DHCP from External Network K ICMP from LAN O Apply Cancel Help Firewall Configura tion window When DoS Port Scan or Service Filtering Protection is enabled it will create a firewall policy to protect your network against the following Dos Protection Port Scan Protection Service Filtering SYN Flood check ICMP Redirection check Null Scan attack SYN RST attack SYN FIN Scan FIN URG PSH attack Xmas Tree Scan Ping from WAN Telnet from WAN FTP from WAN DNS from WAN IKE from WAN RIP from WAN DHCP from WAN ICMP from LAN DSL 522T ADSL Router User Guide A DoS denial of service attack is characterized by an explicit attempt by attackers to prevent legitimate users of a service from using that service Examples include attempts to flood a network thereby preventing legitimate network traffic attempts to disrupt connections between two machines thereby preventing access to a service attempts to prevent a particular individual from accessing a service or attempts to disrupt service to a specific system or person Port
31. P can be set up to dynamically assign IP information Click Yes to continue and then click OK if prompted to restart your computer Configure Windows NT 4 0 for DHCP 1 2 3 4 5 Open the Control Panel window and then double click the Network icon In the Network dialog box click the Protocols tab In the Protocols tab select TCP IP and then click Properties In the Microsoft TCP IP Properties dialog box click the Obtain an IP address automatically option Click OK twice to confirm and save your changes and then close the Control Panel Your computer is now ready to use the Router s DHCP server 79 DSL 522T ADSL Router User Guide C Low Pass Filters for DSL Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services These devices are commonly referred to as microfilters or low pass filters The two basic styles of low pass filters commonly used are described below In Line Filter In line low pass filters are used for each telephone or telephone device answering machines Faxes etc that shares the line with the ADSL service These devices are attached to the telephone cable between the telephone and wall jack Filters that install behind the wall plate hidden from view are also available A typical in line filter installation is shown in the diagram below Phone Jack l Microfilter Phone In line low pass
32. RJ 45 connectors The RJ 45 port on the Router is auto MDI X MDI II meaning that is will link correctly with either MDI II through or MDI X crossed ports The rules governing Ethernet cable lengths apply to the LAN to Router connection Be sure that the cable connecting the LAN to the Router does not exceed 100 meters DSL 522T ADSL Router User Guide 3 Basic Router Configuration The first time you setup the Router it is recommended that you configure the WAN connection using a single computer connected directly to the Router Once the WAN connection is functioning properly you may continue to make changes to Router configuration including IP settings and DHCP setup For information on how to configure advanced features such as port redirection filtering and firewall please skip ahead to the Advanced Router Management section on page Configuration Summary 1 Connect to the Router To configure various settings used by the Router for Internet and access it is first necessary to access the Router s management HTML based interface This is done using an ordinary web browser Your computer must be able to see the Router before it can manage it using a browser If the Router is in the same neighborhood or subnet as the Router you should be able to access the management software Therefore you must first make sure your computer has IP settings that place it in the same subnet as the Router The easiest way to make sure your comput
33. See the next chapter for more details on these windows 10 Typically the globally IP settings e IP address for the WAN interface for a PPPoA or PPPoA connection will use Dynamic IP assignment from the ISP Some accounts may be assigned a specific global IP address If you have been give an IP address for you PPPoE PPPOA connection select the Static IP option from the IP Control pull down menu This menu can be used to configure the WAN port as an Unnumbered IP interface See table below for Unnumbered IP 11 Most users will not need to change ATM settings If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection See the section on ATM Traffic Shaping later in this manual for a further description of the parameters available for ATM traffic shaping 12 When you are satisfied that all the WAN settings are configured correctly click on the Apply button 13 The new settings must be saved and the Router must be restarted for the settings to go into effect To save and reboot the Router click on the Tools directory tab and then click the System button In the System Settings window click the Save and Reboot button under Save Settings and Reboot the System 14 Click OK when the following Save and restart dialog box opens Microsoft Internet Explorer E 2 Save and restart Cancel 15 The Router wi
34. To access the WAN Settings window click on the WAN link button on the left side of the first window that appears when you successfully access the web manager Bridge Mode The WAN Settings window is also used to configure the Router for multiple virtual connections Multiple PVCs Advanced __ Tools Status He Pvc vi UP la VCI EI Virtual Circuit Enabled WAN Setting Bridge Mode Connection Type 1463 Bridged IF LLC Service Category UBR 4 PCR kbps SCR l kbps v Y O Apply Cancel Help WAN Settings window Bridge Mode Select the connection type used for your account The window will display settings that are appropriate for the connection type you select Follow the instruction below according to the type of connection you select in the WAN Settings window For Bridged connections it will be necessary for most users to install additional software on any computer that will the Router for Internet access The additional software is used for the purpose of identifying and verifying your account and then granting Internet access to the computer requesting the connection The 18 DSL 522T ADSL Router User Guide connection software requires the user to enter the User Name and Password for the ISP account This information is stored on the computer not in the Router Follow the instructions below to configure a Bridged connection for the WAN interface To configure a Dynamic IP Address connection pe
35. a including Ethernet Firewire phone line and power line networking Home f dvancec Status To enable UPnP check Enable UPnP and then select a connection T Enable UPnP PwcO Pvt Pura Pwr3 Pyc4 Pyes Pych e C C C C C Pa C Pye v O 0 Apply Cancel Help UPnP window To enable UPnP for any available connection click to check the Enable UPnP selection box select the connection or connections on which you will enable UPnP listed under Available Connections and click the Apply button 42 DSL 522T ADSL Router User Guide Virtual Server Use the Virtual Server window to set up single port trigger port or static port range forwarding rules applied to inbound WAN to LAN traffic The Virtual Server function allows remote users to access services on your LAN such as FTP for file transfers or SMTP and POP3 for e mail The DSL 522T will accept remote requests for these services at your Global IP Address using the specified TCP or UDP protocol and port number and then redirect these requests to the server on your LAN with the LAN IP address you specify Remember that the specified Private IP Address must be within the useable range of the subnet occupied by the Router UDP TCP port redirection is used to direct inbound traffic to the specified servers or workstations on your private network Port redirection can also be used to direct potentially hazardous packets to a proxy server outside your firewall For example yo
36. abled Disabled IF Address OO oO 90 Apply Cancel Help DMZ window To designate a DMZ IP address select the Enabled radio button type in the IP Address of the server or device on your LAN and click the Apply button To remove DMZ status from the designated ID address select the Disabled radio button and click Apply It will be necessary to save the settings and reboot the Router before the DMZ is activated 52 DSL 522T ADSL Router User Guide Firewall The Firewall Configuration window allows the Router to enforce specific predefined policies intended to protect against certain common types of attacks There are two general types of protection DoS Port Scan that can be enabled on the Router as well as filtering for specific packet types sometimes used by hackers You can choose to enable or disable protection against a customized basket of attack and scan types To use DoS Protection or Port Scan Protection select the State Enabled radio button for the protection type and click in the selection boxes for the various types of protection listed under each Service Filtering may ern interfere with other A configurations such as DHCP Relay or Remote Management via Telnet Tools Status Hel DoS attacks can be checked based on your specific need State O Enabled Disabled SYN Flooding checking C ICMP Redirection checking Port Scan attacks can be checked based on your specific need State
37. apter In the TCP IP Properties dialog box click the IP Address tab Click the Obtain an IP address automatically option Double click OK to confirm and save your changes You will be prompted to restart Windows Click Yes When it has restarted your computer is ready to use the Router s DHCP server Windows ME First check for the IP protocol and if necessary install it 1 2 3 Be Oe al SO In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Network icon and then select Properties The Network Properties dialog box displays with a list of currently installed network components If the list includes Internet Protocol TCP IP then the protocol has already been enabled Skip ahead to Configure Windows ME for DHCP If Internet Protocol TCP IP does not display as an installed component click Add In the Select Network Component Type dialog box select Protocol and then click Add Select Microsoft in the Manufacturers box Select Internet Protocol TCP IP in the Network Protocols list and then click OK You may be prompted to install files from your Windows Me installation CD or other media Follow the instructions to install the files 10 If prompted click OK to restart your computer with the new settings 78 DSL 522T ADSL Router User Guide
38. arrangements have been made to use the Router with multiple virtual connections follow the instructions below to setup the Router using the VPI VCI settings given to you by your server provider Configure Multiple PVCs Additional PVCs can be configured by first accessing the WAN configuration window in the Home directory lome Advanced _ Tools Status Hel VPI VC Virtual Circuit WAL Setting Connection Type 1483 Bridged IP LLC Serice Category UBR e HCH SR O Y 0 Apply Cancel Help Select new PVC to configure in the WAN Settings window The PVC pull down menu offers eight virtual connections available for configuration The default PVC used by the Router is labeled PvcO Any additional connections that are configured must have a VPI VCI 39 DSL 522T ADSL Router User Guide combination that is unique to the Router These numbers will have been already been established by your service provider on their network To add a new virtual connection 1 2 3 4 5 Select the new PVC to configure from the pull down menu Enter the values for the VPI and VCI given to you by your service provider To activate the VC select Enabled from the Virtual Circuit pull down menu Configure the WAN Settings and Connection Type as desired To save the new settings click the Save and Reboot button Tools gt System The new connection will activate upon restarting In the example below a new PVC Pvc1 has been added u
39. ator Settings heading type the New Password and Confirm Password to be certain you have typed it correctly Click the Apply button to activate the new password The System User Name remains admin this cannot be changed using the web manager interface Be sure to save the new setting Home Advanced There is only one account thatcan access the DSL 522T s Web Management interface New Password Confirm Password WebP ort top section of the Administrator Settings menu Remote Web Management and Remote Telnet Access The Administrator Settings window is also used to enable remote Telnet management and remote web management access to the Router To enable remote management of the Router select the State Enabled radio button for either Remote Web Management or Remote Telnet Management and type the IP Address and Netmask of the remote network or system used for management Click the Apply button to activate remote management from the chosen IP address Be sure to save the new setting State C Enabled Ge Disabled IF Address Metmask E E E State O Enabled Disabled IF Address Metmask Remote Management menus located in Administrator Settings menu 59 DSL 522T ADSL Router User Guide Time The Router provides a number of options to maintain current date and time including SNTP Home Advanced Status setthe DSL 5277 system time Local Time 03 29 7006 18 14 15 synchronize the ADSL Router
40. cific IP address for the WAN interface In this case you need to change this setting to Static IP When Static IP is selected in the IP Control menu you need to type in the global IP address provided to you by your ISP The P Unnumbered option is used if you want to set up a non TCP IP port protocol link through the WAN interface An IP Unnumbered interface does not have an IP address and therefore cannot be managed via Telnet or any other TCP IP application If you have selected the Static IP option in the IP Control menu type in the global IP address used for your WAN interface Your ISP should provide this IP address to you 28 DSL 522T ADSL Router User Guide ATM Traffic Shaping The ATM settings in the WAN Settings windows for the different connection types can be used to adjust QoS parameters for ADSL clients This may not be available to all ADSL accounts ATM Semice Category HCH SCR 4o CG Apply Cancel Help ATM Settings for WAN connection Additional ATM settings for PPPoE or PPPoA connections ATM Parameters Description The ATM settings allow the user to adjust ATM Quality of Service QoS or traffic parameters to suit specific traffic requirements For applications or circumstances where packet loss or packet delay is a concern ATM QoS can be adjusted to minimize problems For most accounts it will not be necessary to change these settings Altering QoS settings can adversely affect performance of some commonly
41. connection Advanced GT PO Pur z VPI 8 VCI ES virtual Circuit Enabled ze WAM Setting PPPoE PPPoA User Mame Username Password gege Connection Type PPPoE LLO 4 MTU 1400 bytes Diras 1492 bytes Default Route Enabled e NAT Enabled Firewall Enabled ze IP Control Dynamic IP static IP service Category PER SCR a fa en b d TF el Apply Cancel Help WAN Settings window PPPoE PPPoA To set up a PPPoE or PPPoA connection 1 If not already selected choose the PPPoE PPPOA option from the WAN Settings pull down menu PPPOE PPPOA is selected by default if you are configuring the Router for the first time 2 Under the ATM VC Settings at the top of the window should not be changed unless you have been instructed to change them However if you are instructed to change the VPI or VCI values type in the values assigned for your account Leave the PVC and Virtual Circuit setting at the default cv and Enabled values for now This can be used later if you are configuring multiple virtual circuits for your ADSL service For more information see the section on ATM VC Settings later in this manual 26 DSL 522T ADSL Router User Guide 3 Under the PPPoE PPPOA heading type the User Name and Password used for your ADSL account A typical User Name will be in the form user1234 isp co uk The Password may be assigned to you by your ISP or you may have selected it when you set up the account with your ISP 4 C
42. dard format 192 168 0 xxx for the IP address A Static DHCP Client List will appear below the DHCP Client list with any clients that have been configured for static IP address assignment 35 DSL 522T ADSL Router User Guide DNS The Router can be configured to relay DNS settings from your ISP or another available service to workstations on your LAN When using DNS relay the Router will accept DNS requests from hosts on the LAN and forward them to the ISP s or alternative DNS servers DNS relay can use auto discovery or the DNS IP address can be manually entered by the user Alternatively you may also disable the DNS relay and configure hosts on your LAN to use DNS servers directly Most users who are using the Router for DHCP service on the LAN and are using DNS servers on the ISP s network will leave DNS relay enabled either auto discovery or user configured Advanced Tools Status Hel The DNS Configuration allows the user to setthe configuration of ONS DMS Selection Use Auto Discovered DNS Server Ony e User Configuration Preferred DNS Server 168 95 1 1 Alternate DNS Server Oo Y 9 Apply Cancel Help DNS Configuration window In the DNS Relay Selection pull down menu choose to Use Auto Discovered DNS Server Only Use User Discovered DNS ServerOnly or Disable DNS Relay If you have not been given specific DNS server IP addresses or if the Router is not pre configured with DNS server information select the Us
43. dd a static route to a specific destination IP on the local network enter a Destination IP address Netmask then click the Gateway radio button and type in the Gateway s IP address Click Apply to enter the new static route in the table below The route becomes active immediately upon creation To add a static route to a specific destination IP on the WAN click the Connection radio button and choose a connection from the pull down menu then enter a Destination ID address and Netmask Click Apply to enter the new static route in the table below The route becomes active immediately upon creation To remove a static route from the table in the bottom half of the window choose to Delete it from the table and click the Apply button Remember to save the configuration changes 51 DSL 522T ADSL Router User Guide DMZ Since some applications are not compatible with NAT the Router supports use of a DMZ IP address for a single host on the LAN This IP address is not protected by NAT and will therefore be visible to agents on the Internet with the right type of software Keep in mind that any client PC in the DMZ will be exposed to various types of security risks If you use the DMZ take measures such as client based virus protection to protect the remaining client PCs on your LAN from possible contamination through the DMZ Status Hel OMZ Demilitarized one is used to allow a single computer on the LAM to be exposed to the Internet O En
44. ds Tel 31 10 282 1445 Fax 31 10 282 1331 URL www dlink nl Belgium Rue des Colonies 11 B 1000 Brussels Belgium Tel 32 0 2 517 7111 Fax 32 0 2 517 6500 URL www dlink be Italy Via Nino Bonnet n 6 b 20154 Milano Italy TEL 39 02 2900 0676 FAX 39 02 2900 1723 URL www dlink it Sweden P O Box 15036 S 167 15 Bromma Sweden TEL 46 0 8564 61900 FAX 46 0 8564 61901 URL www dlink se Denmark Naverland 2 DK 2600 Glostrup Copenhagen Denmark TEL 45 43 969040 FAX 45 43 424347 URL www dlink dk Norway Karihaugveien 89 N 1086 Oslo Norway TEL 47 99 300 100 FAX 47 22 30 95 80 URL www dlink no Finland Pakkalankuja 7A 3rd floor FIN 0150 10 Vantaa Finland TEL 358 9 2707 5080 FAX 358 9 2707 5081 URL www dlink fi D Link nternational Offices Spain C Sabino De Arana 56 Bajos 08028 Barcelona Spain TEL 34 93 4090770 FAX 34 93 4910795 URL www dlink es Portugal Rua Fernando Pahla 50 Edificio Simol 1900 Lisbon Portugal TEL 351 21 8688493 URL www dlink es Czech Republic Vaclavske namesti 36 Praha 1 Czech Republic TEL 420 603 276 589 URL www dlink cz Switzerland Glatt Tower 2 0G CH 8301 Glattzentrum Postfach 2 0G Switzerland TEL 41 0 1 832 11 00 FAX 41 0 1 832 11 01 URL www dlink ch Greece 101 Panagoulis Str 163 43 Helioupolis Athens Greece TEL 30 210 9914 512 FAX 30 210 9916902 URL www dlink gr Luxemburg Rue de
45. e The InstallShield Wizard has successfully installed D Link DSLs Click Finish to exit the wizard Back Finish Cancel 4 Click Finish to complete the InstallShield wizard When the USB driver has been installed insert one end of the USB cable included with the router into the DSL 522T router s USB port Insert the other end of the USB cable into a USB port on your PC Connect the power adapter to the power input at the back panel of the DSL 522T and then plug the other end of the power adapter to a wall outlet or power strip On the front of the device the Power LED will turn ON to indicate proper operation Insert the telephone cable included with the Router into the ADSL port and then connect the cable to your telephone line Check the LED display on the front of the Router to confirm that the connections have been made DSL 522T ADSL Router User Guide Introduction This section provides a brief description of the Router its associated technologies and a list of Router features Router Description and Operation The DSL 522T Router is designed to provide a simple and cost effective ADSL Internet connection for a private Ethernet network The Router combines high speed ADSL Internet connection IP routing for the Local Area Network LAN connectivity in one package The Router is easy to install and use The DSL 522T connects to an Ethernet LAN or computers via standard Ethernet ports The ADSL connection is made usi
46. e provider s network It is commonly in the form user isp co uk Your ADSL service provider uses this to identify your account This is the Password used in conjunction with the Username Password above to log on to your ADSL service provider s network This is used to verify the identity of your account These settings describe the method your ADSL service provider uses to transport data between the Internet and your computer Most users will use the default settings You may need to specify one of the following WAN Setting and Connection Type configurations Connection Type settings listed in parenthesis PPPOE PPOA PPPoE LLC PPPoA LLC or PPPoA VC Mux WAN Setting Bridge Mode 1483 Bridged IP LLC or Connection Type 1483 Bridged IP VC Mux Static IP Address Bridged IP LLC 1483 Bridged IP VC Mux 1483 Routed IP LLC 1483 Routed IP VC Mux or IPoA Dynamic IP Address 1483 Bridged IP LLC or 1483 Bridged IP VC Mux Default PPPoE PPPOA PPPoE LLC Most users will not be required to change this setting The Virtual Path Identifier VPI is used in conjunction with the Virtual Channel Identifier VCI to identify the data path between your ADSL service provider s network and your computer If you are setting up the Router for multiple virtual connections you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections This setting can be changed in the WAN Settings window o
47. e Auto Discovered DNS ServerOnly option Auto discovery DNS instructs the Router to automatically obtain the DNS IP address from the ISP through DHCP If your WAN connection uses a Static IP address auto discovery for DNS cannot be used If you have DNS IP addresses provided by your ISP enter these IP addresses in the available entry fields for the Preferred DNS Server and the Alternative DNS Server If you choose to Disable DNS Relay it will be necessary to configure DNS settings for hosts on the LAN since they will not be depending on the Router to forward the DNS requests When you have configured the DNS settings as desired click the Apply button A To use DNS Relay for computers on your local network DNS Service Filtering must be Note disabled See the Firewall section in the next chapter 36 DSL 522T ADSL Router User Guide Dynamic DNS The Router supports DDNS Dynamic Domain Name Service The Dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains allowing access to a specified host from various locations on the Internet This is enabled to allow remote access to a host by clicking a hyperlinked URL in the form hostname dyndns org Many ISPs assign public IP addresses using DHCP this can make it difficult to locate a specific host on the LAN using standard DNS If for example you are running a public web server or VPN server on your LAN this ensures that the hos
48. e to filter To filter WAN to LAN traffic select the Inbound Filter option Any new Inbound Filter rules created will appear in the list Likewise should you to filter LAN to WAN traffic create an Outbound Filter rule ES The Service Filtering feature of the Firewall may interfere with ules configured in the Filters window For example FTP packets are not allowed through from the external Note network by default See the Firewall section below for details 48 DSL 522T ADSL Router User Guide The parameters described in the table below are used to set up filter rules Click the Apply button to put the new rule into effect Any filter rule configured in the menu will appear in the Filters List with the new settings The Router must save the new settings and reboot before the new rules are applied Filters Parameter Description For an Outbound Filter this is the IP address or IP addresses on your LAN for which you are creating the filter rule For an Inbound Filter this is the IP address or IP addresses for which you are creating the filter rule You can opt to indicate a Single IP an IP Range or Any IP from the pull down menu Choosing Any IP will apply the rule to all WAN or all LAN IP addresses depending on which type of rule Inbound or Outbound is being configured Source IP Where the Destination ID address resides also depends on if you are Destination IP configuring an Inbound or Outbound filter rule You can opt to indicate a
49. ed WAN Virtual Circuit Ech Status Mot Connected Connect Connection Type pppoe IP Address KI Subnet Mask NI Default Gateway MA DAS Server HI Device Information window 66 DSL 522T ADSL Router User Guide DHCP Clients e Home Advanced _ Tools DHCP Clients MAC Address IF Address Host Name 192 165 1 4 accounting 67 DSL 522T ADSL Router User Guide Log The system log displays chronological event log data Use the navigation buttons to view or scroll log pages You may also save a simple text file containing the log to your computer Click the Save Log button and follow the prompts to save the file Home Advanced Tools View Log displays the activities occurring on the DSL 522T First Page Last Page PrewIous Next Clear Log Sawe Log Help page 1 ofi Time Jan 1 12 00 10 gt The firmware build datetime 20051219121434 Jan 1 12 00 10 gt Valid Configuration Tree Jan 1 12 00 11 NTP Polling Timer for DHCP Started succestully Jan 1 12 00 11 DSL Polling Timer Started succesfully Jan 1 12 00 11 gt Firewall NAT service started Jan 1 12 00 15 starting on port GU Jan 1 12 00 15 gt Bridge Created br lar 1 19 M1 bridas Prado ks View Log window Click Clear Log to delete the current log information 68 DSL 522T ADSL Router User Guide Statistics Use the Traffic Statistics window to monitor traffic on the Ethernet or ADSL connection Select the interface f
50. elephone line Media Interface LAN interface RJ 45 port for 10 100BASE T Ethernet connection USB interface USB 1 1 Specification 12 DSL 522T ADSL Router User Guide DC Inputs Input 120V AC 60Hz Power Adapter OPE A Power 11 25 Watts max Consumption Operating 0 to 40 C Temperature Temperature 5 to 95 non condensing gr Je zm esenscnecn LE Reliability Mean Time Between Failure MTBF min 4 years 73 DSL 522T ADSL Router User Guide Configuring IP Settings on Your Computer In order to configure your system to receive IP settings from the Router it must first have the TCP IP protocol installed If you have an Ethernet port on your computer it probably already has TCP IP protocol installed If you are using Windows XP the TCP IP is enabled by default for standard installations Below is an illustrated example of how to configure a Windows XP system to automatically obtain IP settings from the Router Following this example is a step by step description of the procedures used on the other Windows operating systems to first check if the TCP IP protocol has been installed if it is not instructions are provided for installing it Once the protocol has been installed you can configure the system to receive IP settings from the Router For computers running non Windows operating systems follow the instructions for your OS that configure the system to receive an IP address from the Router that is c
51. er has the correct IP settings is to configure it to use the DHCP server in the Router The DHCP server will automatically enable your computer to use a browser to manage the Router The next section describes how to change the IP configuration for a computer running a Windows operating system to be a DHCP client If you are running another operating system make sure your computer is configured as a DHCP client so it can automatically obtain IP settings from the Router Some operating systems will automatically select the best IP settings Consult the user manual for the operating system OS if you are unsure 2 Configure the Internet WAN Connection Most users will be able to complete this process using the Setup Wizard The Setup Wizard can be launched once you have successfully connected with the Routers management software There are different methods used to establish the WAN connection to the service provider s network and ultimately to the Internet Your Router may already have most of the settings configured by default However you will probably at least have to type in a user name and password given to you by your ISP You may also need to know the encapsulation and connection type required to use for your ADSL service Your service provider should provide all the information needed to configure the WAN connection Computer IP Settings In order to configure your system to receive IP settings from the Router your computer must first have the
52. er is done using the web based management interface pictured in the above example The configuration windows are accessed by clicking on the directory tabs Home Advanced Tools Status and Help Each tab has associated window buttons in the left hand panel of the web interface Basic setup of the Router can be completed in the windows accessed from the Home directory including Setup Wizard WAN Internet LAN to configure the IP address of the Router DHCP DNS and Dynamic DNS DSL 522T ADSL Router User Guide Wizard To use the Setup Wizard click the Run Wizard button in the first browser window and follow the instructions in the pop up window that appears The initial wndow summarizes the setup process Click the Next button to proceed You may stop using the Setup Wizard at any time by clicking the Exit button If you exit the wizard you will return to the Setup Wizard window without saving any of the settings changed during the process 2 DSL 5227 Microsoft Internet Explorer Welcome to the DSL 5227 setup Wizard The Wizard will guide you Through these three quick steps Begin by clicking on Next Step 1 Choose your time zone Step 2 Set Internet connection Step 3 Restan The first pop up window of the Setup Wizard lists the basic steps in the process These steps are as follows 1 Setthe system time 2 Configure the connection to the Internet 3 Save the new configuration settings and reboot the system 10 DSL
53. f the web management interface Default value 8 Most users will not be required to change this setting The Virtual Channel Identifier VCI used in conjunction with the VPI to identify the data path between your ADSL service provider s network and your computer If you are setting up the Router for multiple virtual connections you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections This setting can be changed in the WAN Settings window of the web management interface Default value 35 The Setup Wizard can be used to configure the Internet connection for most users Vi DSL 522T ADSL Router User Guide Information you will need about your DSL 522T ADSL Router Record info here This is the Username needed access the Router s management interface When you attempt to connect to the device through a web browser you will be prompted to enter this Username The default Username for the Router is admin The user cannot change this This is the Password you will be prompted to enter when you access the Router s management interface The default Password is admin The user may change this Password This is the IP address you will enter into the Address field of your web browser to access the Router s configuration graphical user interface GUI using a LAN IP addresses for web browser The default IP address is 192 168 1 1 the DSL 522T This may be
54. hoose the Connection Type from the pull down menu located under the User Name and Password entry fields This defines both the connection protocol and encapsulation method used for your ADSL service The available options are PPPoA VC Mux PPPoA LLC and PPPoE LLC If have not been provided specific information for the Connection Type setting leave the default setting 5 Leave the MTU value at the default setting default 1400 unless you have specific reasons to change this see table below 6 Leave the MRU value at the default setting default 7492 unless you have specific reasons to change this see table below 7 Leave the Default Route enabled if you want to use the Router as the default route to the Internet for your LAN Whenever a computer on the LAN attempts to access the Internet the Router becomes the Internet gateway to the computer If you have an alternative route for Internet traffic you may disable this without effecting the Router s connection 8 NAT should remain Enabled If you disable NAT you will not be able to use more than one computer for Internet connections NAT is enabled and disabled system wide therefore if you are using multiple virtual connections NAT will disabled on all connections 9 The Firewall should remain enabled for most users If you choose to disable this you will not be able to use the features configured in the Firewall Configuration and Filters windows located in the Advanced directory
55. ick the Disconnect button to terminate the PPP session 55 DSL 522T ADSL Router User Guide ADSL The ADSL Configuration window allows the user to set the configuration for ADSL protocols For most ADSL accounts the default settings ADSL2 Multi mode will work This configuration works with all ADSL implementations If you have been given instructions to change the Modulation method used select the desired option from the Modulation Type drop down menu and click the Apply button Tools Status Hel The ADSL Configuration page allows the user to setthe configuration for ADSL protocol Modulation Type ADSL2 Multi Mode O Y O Apply Cancel Help ADSL Configuration window 56 DSL 522T ADSL Router User Guide ATM VCC Theis window is used to configure the WAN connection If you are using multiple PVCs you can change the configuration of any PVC in this window To create new or additional PVCs read the section on Multiple PVCs This window can be used as an alternative to configure the same settings found on the WAN Settings window in the Home directory Tools Status VPI E WC 35 Virtual Circuit Enabled ze WAN Setting Bridge Mode Connection Type 1483 Bridged IF LLC 4 Y Apply Cancel ATM VCs List Connection Type Virtual Circuit Enabled ATM VC Setting window To configure an existing PVC configuration set click the corresponding notepad icon in the right hand column of the ATM
56. iguration windows See the previous chapter for a description of the Home directory windows Home Click the Advanced tab to access the UPnP Virtual Server LAN Clients SNMP Management Filters Bridge Filters Static Routing Table DMZ Firewall Configuration RIP Systemwide Configuration PPP Connection ADSL Configuration and ATM VC Setting windows Advanced Click the Tools tab to access the Administrator Settings used to set the system user name and password backup and load settings Time Remote Log Settings System Settings Firmware Upgrade Miscellaneous Configuration and Diagnostic Test windows Click the Status tab to view the Device Information DHCP Clients View Log Traffic Statistics and ADSL Status windows The Help window presents links to pages that explain various functions and services provided by the Router 4 DSL 522T ADSL Router User Guide UPnP UPnP supports zero configuration networking and automatic discovery for many types of networked devices When enabled it allows other devices that support UPnP to dynamically join a network obtain an IP address convey its capabilities and learn about the presence and capabilities of other devices DHCP and DNS service can also be used if available on the network UPnP also allows supported devices to leave a network automatically without adverse effects to the device or other devices on the network UPnP is a protocol supported by diverse networking medi
57. in Enabled If you disable NAT you will not be able to use more than one computer for Internet connections NAT is enabled and disabled system wide therefore if you are using multiple virtual connections NAT will be disabled on all connections The Firewall should remain enabled for most users If you choose to disable this you will not be able to use the features configured in the Firewall Configuration and Filters window located in the Advanced directory See the next chapter for more details on these windows Most users will not need to change ATM settings If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection See the section on ATM Traffic Shaping later in this manual for a further description of the parameters available for ATM traffic shaping When you are satisfied that all the WAN settings are configured correctly click on the Apply button 10 The new settings must be saved and the Router must be restarted for the settings to go into effect To save and reboot the Router click on the Tools directory tab and then click the System button In the System Settings window click the Save and Reboot button under Save Settings and Reboot the System 11 Click OK when the following Save and restart dialog box opens Microsoft Internet Explorer E K Save and restart i Cancel 12 The Ro
58. it size for downloading data Most users will be happy with the default setting 1492 bytes However this may also be optimized for fast downloads of general bulk Internet traffic for low latency or for downloading to computers on the Wireless LAN As with the MTU setting the user should carefully consider how changing the MRU may affect Internet downloads for all systems on your LAN When this is enabled the Router will be considered to be the primary gateway to the Internet and WAN for systems on your network If you are using the Router on a network with one or more alternative gateway routers you may prefer to disable this if you will use another router as the primary gateway Network Address Translation may be enabled or disabled with the pull down menu Keep in mind that disabling NAT allows only a single computer to be used for Internet access through the Router NAT is enabled and disabled for the Router on all connections i e PvcO Pvc7 if your Router is set up for multiple virtual connections Use this to universally enable or disable the Firewall and Filter features available in the Router If you disable this you will not be able to configure settings in the Firewall Configuration window or Filters window in the Advanced directory This is used to determine how global IP settings are handled for the WAN interface Typically PPPoE or PPPoA connections will use the default setting for Dynamic IP Some users will be given a spe
59. ke sure you understand all the prerequisites for proper installation of your new Router Have all the necessary information and equipment on hand before beginning the installation Installation Overview The procedure to install the Router can be described in general terms in the following steps 1 Gather information and equipment needed to install the device Before you begin the actual installation make sure you have all the necessary information and equipment 2 Install the hardware connect the cables to the device and connect the power adapter You will need to install a software driver to use the USB port See the instructions below or go to the QIG for more details 3 Check the IP settings on your computer and change them if necessary so the computer can access the web based software built into the Router 4 Use the web based management software to configure the device to suit the requirements of your ADSL service and requirements of your local network Setup Wizard Many users will be able to configure all the settings necessary to use the DSL 522T with the Setup Wizard For ADSL connections that use PPPoE or PPPoA connections the simplest way to set up the DSL 522T is to use the Setup Wizard to configure the Internet connection Once you access the web interface used to configure the device just launch the Setup Wizard to configure your Internet connection lf you are connecting a computer to the Router via the USB interface
60. l for a further description of the parameters available for ATM traffic shaping When you are satisfied that all the WAN settings are configured correctly click on the Apply button The new settings must be saved and the Router must be restarted for the settings to go into effect To save and reboot the Router click on the Tools directory tab and then click the System button In the System Settings window click the Save and Reboot button under Save Settings and Reboot the System Click OK when the following Save and restart dialog box opens Microsoft Internet Explorer E 2 Save and restart Cancel The Router will save the new settings and restart Upon restarting the Router will automatically establish the WAN connection 19 Dynamic IP Address A Dynamic IP Address connection configures the Router to automatically obtain its global IP address from a DHCP server on the ISP s network The service provider assigns a global IP address from a pool of addresses available to the service provider Typically the IP address assigned has a long lease time so it will DSL 522T ADSL Router User Guide likely be the same address each time the Router requests an IP address To configure a Dynamic IP Address connection perform the steps listed below Some of the settings do not need to be changed the first time the device is set up but can be changed later if you choose See the table below for a description of all the setti
61. lect the Connection Type specific to your service and click Next to go to the next Setup Wizard pop up window Follow the instructions below for the type of connection you have selected 12 DSL 522T ADSL Router User Guide Using the Setup Wizard For PPPoE PPPoA connections 1 Type in the Username and Password used to identify and verify your account to the ISP 2 Select the specific Connection Type from the drop down menu The available PPP connection and encapsulation types are PPPoE LLC PPPoA LLC and PPPoA VC Mux 3 If you are instructed to change the VPI or VCI number type in the correct setting in the available entry fields Most users will not need to change these settings The Internet connection cannot function if these values are incorrect 4 Click Next to go to the next window and complete the Setup Wizard Al DSL 527T Microsoft Internet Explorer all DSESIZWADSEROUTEN set PPPoE J PPPoA Enter the PPPoE PPPoA information provided to you by your ISF Click Next to continue UserName Username VP dg ze PPPoELLC Connection Type 9 0 Back Next Exit 13 DSL 522T ADSL Router User Guide Using the Setup Wizard For Dynamic IP Address connections 1 Select the specific Connection Type from the drop down menu The available Dynamic IP Address connection and encapsulation types are 1483 Bridged IP LLC and 1483 Bridged IP VC Mux If you are instructed to change the VPI or VCI number
62. lients Bridge Filters Routing DMZ Firewall Rules RIP Configuration PPF Configuration ADSL Configuration ATM VCC Configuration Tools e Administrator Settings Time Remote Log System Settings Firmware Upgrade Miscellaneous items Test status Device Information DHCP Clients Log Statistics ADSL Status Help window Click the desired hyperlink to access helpfiles 71 DSL 522T ADSL Router User Guide Technical Specifications ADSL2 Standards ADSL Standards o ANSI 11 413 Issue 2 ITU G 992 1 G dmt AnnexA o ITU G 992 3 G dmt bis Annex A ITU G 992 4 G lite bis Annex A Standards ITU G 992 2 G lite Annex A ITU G 994 1 G hs ITU G 992 5 Annex A IEEE 802 1d Spanning Tree RFC1483 2684 Multiprotocol Encapsulation over TCP UDP ATM Adaptation Layer 5 AAL5 ARP RFC1577 Classical IP over ATM RARP RFC1661 Point to Point Protocol Protocols ICMP RFC1994 CHAP RFC1058 RIP v1 RFC2131 DHCP Client DHCP RFC1213 SNMP v1 8 v2c Server RFC1334 PAP RFC2364 PPP over AIM RFC1389 RIP v2 RFC2516 PPP over Ethernet G dmt full rate downstream up to 8 Mbps upstream up to 1 Mbps G lite ADSL downstream up to 1 5 Mbps upstream up to 512 Kbps Data Transfer Rate G dmt bis full rate downstream up to 12 Mbps upstream up to 12 Mbps ADSL full rate downstream up to 24 Mbps upstream up to 1 Mbps ADSL interface RJ 11 connector for connection to 24 26 AWG twisted pair t
63. ll save the new settings and restart Upon restarting the Router will automatically establish the WAN connection 21 DSL 522T ADSL Router User Guide Additional settings for PPPoE PPPOA connections PPPoE PPPoA Parameters User Name Password Connection Type MTU MRU Default Route NAT Firewall IP Control Static IP Description For PPP connections a User Name and Password are used to identify and verify your account to the ISP Enter the User Name for your ADSL service account User names and passwords are case sensitive so enter this information exactly as given to you by your ISP Together with the User Name this is used to verify your account to the ISP Enter the Password exactly as given to you by your ISP This specifies the protocol PPPoE or PPPoA and the encapsulation method LLC or VC Mux used for your connection The options available are PPPoE LLC PPPoA LLC or PPPoA VC Mux The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface The default setting 1400 bytes should be suitable for most users Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired such as with Internet gaming It is highly recommended that the user research how adjusting the MTU may affect network traffic for better or worse Similar to the MTU except this applies to Maximum Received Un
64. n point to Settings and then click Control Panel Double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Local Area Connection icon and then select Properties The Local Area Connection Properties dialog box displays with a list of currently installed network components If the list includes Internet Protocol TCP IP then the protocol has already been enabled skip ahead to Configure Windows 2000 for DHCP If Internet Protocol TCP IP does not display as an installed component click Install In the Select Network Component Type dialog box select Protocol and then click Add Select Internet Protocol TCP IP in the Network Protocols list and then click OK You may be prompted to install files from your Windows 2000 installation CD or other media Follow the instructions to install the files If prompted click OK to restart your computer with the new settings Configure Windows 2000 for DHCP 1 2 O In the Control Panel double click the Network and Dial up Connections icon In Network and Dial up Connections window right click the Local Area Connection icon and then select Properties In the Local Area Connection Properties dialog box select Internet Protocol TCP IP and then click Properties In the Internet Protocol TCP IP Properties dialog box click the button labeled Obtain an IP address automatically Double click OK to confirm and save your
65. nection 2 Properties KEN General Authentication Advanced Connect uzing Bai D Link DFE 5507 10 100 Adapter O ENWLink NetBIOS A NW Link Fe SPAN etBIOS Compatible Transport Prot ma Internet Protocol TCPAIP This connection uses the following items Click Properties ees Properties Description Transmission Control Protocal nternet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected np _ 22 6 Select Obtain an IP address automatically by clicking once in the circle Click the OK button Internet Protocol TCP IP Properties Ed General Alternate Configuration Tou can get IF settings assigned automatically if your network supports this capability Othenwise you need to ask your network administrator for the appropriate IP settings Select Obtain an IP address Obtain an IP address automatically automatically in the Internet Protocol A Use the Following Ir address TCP IP Properties window al ll rm F gadd Ess Your computer is now ready to use the Router s DHCP server 76 DSL 522T ADSL Router User Guide Windows 2000 First check for the IP protocol and if necessary install it 1 2 3 Ot ier 9 In the Windows task bar click the Start butto
66. ng When you are satisfied that all the WAN settings are configured correctly click on the Apply button 10 The new settings must be saved and the Router must be restarted for the settings to go into effect To save and reboot the Router click on the Tools directory tab and then click the System button In the System Settings window click the Save and Reboot button under Save Settings and Reboot the System 11 Click OK when the following Save and restart dialog box opens Microsoft Internet Explorer E 2 Save and restart Cancel 12 The Router will save the new settings and restart Upon restarting the Router will automatically establish the WAN connection 21 DSL 522T ADSL Router User Guide Additional settings for Dynamic IP Address connections Dynamic IP Parameters Connection Type Cloned MAC Address Cloned MAC Address Firewall Description This specifies the connection type and encapsulation method used for your Dynamic IP Address connection The options available are Bridged IP LLC or Bridged IP VC Mux This is not always necessary but may be required for some ISPs Type in the MAC address of your computer s Ethernet adapter in the Cloned MAC Address field and click the Clone MAC Address button This will copy the information to a file used by the Router to present to the ISP s server used for DHCP Some ISPs record the unique MAC address of your computer s Ethernet adapter when yo
67. ng ordinary telephone line with standard connectors Multiple workstations can be networked and connected to the Internet using a single Wide Area Network WAN interface and single global IP address The advanced security enhancements packet filtering and port redirection can help protect your network from potentially devastating intrusions by malicious agents from outside your network ADSL Asymmetric Digital Subscriber Line ADSL is a broadband network technology that utilizes standard twisted pair copper wire telephone lines to enable broadband high speed digital data transmission and bandwidth hungry applications for business and residential customers ADSL routers and modems provide faster downloads and more reliable connectivity to the user without loss of quality or disruption of voice fax telephone capabilities ADSL service operates at speeds of up to 24 Mbps downstream and up to 1 Mbps upstream A secure dedicated point to point connection is established between the user and the central office of the service provider DSL 522T ADSL Router User Guide Router Features The DSL 522T ADSL Router utilizes the latest ADSL enhancements to provide a reliable Internet portal suitable for most small to medium sized offices DSL 522T advantages include PPP Point to Point Protocol Security The DSL 522T ADSL Router supports PAP Password Authentication Protocol and CHAP Challenge Handshake Authentication Protocol for PPP connectio
68. ng the reset button Connect network cables 1 Insert the ADSL telephone cable included with the Router into the ADSL port and then connect the cable to your telephone line 2 Insert one end of the Ethernet cable into the Ethernet LAN port on the back panel of the Router and the other end of the cable to an Ethernet Adapter or available Ethernet port on your computer Ethernet 9V AC 1A Ethernet Port Power Insert ADSL Port Use the Ethernet port Use the adapter Use the ADSL cable to to connect the Router shipped with the connect to the your telephone to your Ethernet LAN Router to connect to line RJ 11 port or computer power source USB Port Reset Button Connect USB cable here To manually reset depress and install USB driver button with the power on for at least seven seconds DSL 522T ADSL Router User Guide Hardware Installation The DSL 522T maintains three separate interfaces an ADSL an Ethernet and a USB interface Place the Router in a location where it can be connected to the various devices as well as to a power source The Router should not be located where it will be exposed to moisture or excessive heat Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard As with any electrical appliance observe common sense safety procedures The Router can be placed on a shelf or desktop ideally you should be able to see the LED indicators on the front if yo
69. ngs available in this window Advanced PY VPI VU Virtual Circuit WAR Setting Connection Type Cloned MAC Address Cloned MAC Address MTL MAT Firewall Seice Category PER GCH Tools Help Enabled i Dynamic IP Address Y 1483 Bridged IPLLC ei Clone MAC Address 1400 bytes Enabled Enabled UBR Y kbps kbps Apply Cancel Help WAN Settings window Dynamic IP Address 20 DSL 522T ADSL Router User Guide To configure a Dynamic IP Address connection for the WAN follow these steps 1 2 9 Choose the Dynamic IP Address option from the WAN Settings pull down menu Under the ATM VC Settings at the top of the window should not be changed unless you have been instructed to change them However if you are instructed to change the VPI or VCI values type in the values assigned for your account Leave the PVC and Virtual Circuit setting at the default PcvO and Enabled values for now This can be used later if you are configuring multiple virtual circuits for your ADSL service For more information see the section on ATM VC Settings later in this manual Under the Dynamic IP heading choose the Connection Type from the pull down menu This defines both the connection type and encapsulation method used for your ADSL service The available options are 1483 Bridged IP LLC and 1483 Bridged IP VC Mux If have not been provided specific information for the Connection Type
70. ns DHCP Support Dynamic Host Configuration Protocol automatically and dynamically assigns all LAN IP settings to each host on your network This eliminates the need to reconfigure every host whenever changes in network topology occur Network Address Translation NAT For small office environments the DSL 522T allows multiple users on the LAN to access the Internet concurrently through a single Internet account This provides Internet access to everyone in the office for the price of a single user NAT improves network security in effect by hiding the private network behind one global and visible IP address NAT address mapping can also be used to link two IP domains via a LAN to LAN connection TCP IP Transfer Control Protocol Internet Protocol The DSL 522T supports TCP IP protocol the language used for the Internet It is compatible with access servers manufactured by major vendors RIP 1 RIP 2 The DSL 522T supports both RIP 1 and RIP 2 exchanges with other routers Using both versions lets the Router to communicate with all RIP enabled devices Static Routing This allows you to select a data path to a particular network destination that will remain in the routing table and never age out If you wish to define a specific route that will always be used for data traffic from your LAN to a specific destination within your LAN for example to another router or a server or outside your network to an ISP defined default
71. nternet and WAN Most users will not need to change this setting The Virtual Channel Identifier is used with the VPI to define a dedicated circuit on the ATM network portion of the connection to the Internet and WAN Most users will not need to change this setting As with the PVC setting this is mainly for use by clients who are configuring the Router for multiple virtual connections Use this to enable or disable the PVC you are currently configuring By default the PvcO is Enabled and the remaining PVCs are disabled 30 DSL 522T ADSL Router User Guide LAN You can configure the LAN IP address to suit your preference Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network The IP address of the Router is the base address used for DHCP In order to use the Router for DHCP on your LAN the IP address pool used for DHCP must be compatible with the IP address of the Router The IP addresses available in the DHCP IP address pool will change automatically if you change the IP address of the Router See the next section for information on DHCP setup To access the Management IP window click the LAN button in the Home directory ne Advanced Tools Status ul These are the IF settings of the LAN interface forthe DsL 5207 These setting may be referred to as Private settings You may change the LAN IP address if needed IP Address 192 168 1 1 Subnet
72. onfigure the system to be a DHCP client If you are using this Router to provide Internet access for more than one computer you can use these instructions later to change the IP settings for the other computers However you cannot use the same IP address since every computer must have its own IP address that is unique on the local network Configure Windows XP for DHCP Use the following steps to configure a computer running Windows XP to be a DHCP client 1 From the Start menu on your desktop go to Control Panel MU E CTT Ab o beams mg D J z a Ai j 74 DSL 522T ADSL Router User Guide 2 Inthe Control Panel window click amp Control Panel Network and Internet Connections File Edit View Favorites Tools Help ka yo Search E Folders Et D Control Panel A A Va Control Panel Internet kM Click Network and Connections 3 E Network and Internet Connections In the Network and Internet Connections window Pick a category we SN Printers and Other Hardware em T Appearance and Themes a Ee wa User Accounts Network and Internet Connectior e A Date Time Language and Regional g Options Accessibility Options V Add or Remove Programs gt J y Sounds Speech and Audio Devices y Performance and Maintenance click Network Connections File Edit View Favorites Tools Help Q Back O z O ES Search Key
73. or a web server Usually this will be a server owned by the ISP Get this IP address from your ISP This is the second choice for a DNS server Get this IP address from your ISP The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface The default setting 7400 bytes should be suitable for most users Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired such as with Internet gaming It is highly recommended that the user research how adjusting the MTU may affect network traffic for better or worse Network Address Translation may be enabled or disabled with the pull down menu Keep in mind that disabling NAT allows on a single computer to be used for Internet access through the Router NAT is enabled and disabled for the Router on all connections i e PvcO Pvc7 if your Router is set up for multiple virtual connections Use this to universally enable or disable the Firewall and Filter features available in the Router If you disable this you will not be able to configure settings in the Firewall Configuration window or the Filters window in the Advanced directory 25 DSL 522T ADSL Router User Guide PPPoE PPPoA Follow the instructions below to configure the Router to use a PPPoE or PPPOA for the Internet connection Make sure you have all the necessary information before you configure the WAN
74. or which you want to view packet statistics and the information will appear below _ Home Advanced Tools Traffic Statistics display Receive and Transmit packets passing through the DSL 527T Choose an interface to view your network status Ge Ethernet Display Receive and Transmit packages through Ethernet C ADSL Display Receive and Transmit packages through ADSL Refresh Good Ts Frames Good Tx Broadcast Frames U Good Tx Multicast Frames O Tx Total Bytes 4056449 Collisions Error Frames Carrer Sense Errors Good Rx Frames Good Rx Broadcast Frames Good Tx Multicast Frames Rx Total Bytes CRC Errors Undersized Frames Oyeruns Traffic Statistics window Click Refresh to view traffic information 69 DSL 522T ADSL Router User Guide ADSL Status Use the ADSL Status window for troubleshooting the ADSL connection Home Advanced Tools ADSL status show s the ADSL physical layer status ADSL Firmware Version 5 00 04 00 5 00 03 00 5 00 05 00 Annex A 01 07 2b 0 52 ADSL Software Version V3 00B801T01 EU 20060210 Line State Connected Modulation NO MODE Annex Mode ANNEX A Wax Tx Power 38 dBmiHz item Downstream Upstream SNR Margin 19 E Line Attenuation 4 21 Data Rate 640 ADSL Status information 70 DSL 522T ADSL Router User Guide Advanced Tools Status setup Wizard WAN Settings LAN Settings DHCP Server DNS Settings Dynamic DNS Settings Advanced e UPNP Virtual Server Lan C
75. p The user name and password used to access the web based manager is NOT the same as the DSL 522T ADSL Router User Guide Configure the Router When you successfully connect to the web manager the Home directory tab will display the Setup Wizard window You can launch the Setup Wizard from this page or use the buttons located in the left panel of the web page to view other windows used for basic configuration Click on a directory tab to view the windows available in that directory 23 http 192 168 1 1 cgi binAvebem Microsoft Internet File Edit View Favorites Tools Help Bak v d DN a L ya Search 5 Favorites A media d Gi d Address E http 192 168 1 1 cgi binfwebcm Google v C Search QB g Br2blockedff SE check D Link Building Networks for People GC ay l Go Links gt A Autolink ea Options Se DSL 522T ADSL Router Advanced Tools Status Help The DSL 522T is an ADSL Router ideal for home networking and small business networking The setup wizard will guide you to configure the DSL 522T to connect to your ISP Internet anice Provido bel H at siti onto have Internet access within e the DSL 522T Click on a button to use or view the window Dynamic DNS Logout Click the Run Wizard Help button to launch the Setup Wizard El Done Internet Web Manager First Time Log On All configuration and management of the Rout
76. rform the steps listed below Some of the settings do not need to be changed the first time the device is set up but can be changed later if you choose See the table below for a description of all the settings available in this window 1 2 8 Choose the Bridge Mode option from the WAN Settings pull down menu Under the ATM VC Settings at the top of the window should not be changed unless you have been instructed to change them However if you are instructed to change the VPI or VCI values type in the values assigned for your account Leave the PVC and Virtual Circuit setting at the default Pcv0 and Enabled values for now This can be used later if you are configuring multiple virtual circuits for your ADSL service For more information see the section on ATM VC Settings later in this manual Under the Bridge Mode heading choose the Connection Type from the pull down menu This defines both the connection type and encapsulation method used for your ADSL service The available options are 1483 Bridged IP LLC and 1483 Bridged IP VC Mux If have not been provided specific information for the Connection Type setting leave the default setting Most users will not need to change ATM settings If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection See the section on ATM Traffic Shaping later in this manua
77. ridged IP VC Mux 1483 Routed IP LLC 1483 Routed IP VC Mux and IPoA 2 Change the IP Address Subnet Mask ISP Gateway Address Primary DNS Address and Secondary DNS Server IP Address as instructed by your ISP For IPoA connections it may also be necessary to change the ARP Server Address IPoA connection users who have not been given this information should leave the field blank 3 If you are instructed to change the VPI or VCI number type in the correct setting in the available entry fields Most users will not need to change these settings The Internet connection cannot function if these values are incorrect 4 Click Next to go to the next window and complete the Setup Wizard 2 DSL 527T Microsoft Internet Explorer PEER VSL Rer Set Static IP Address Enter the static IP information provided to you by your ISP Click Next to continue VFI VC IP Address oubnet Mask ISP Gateway Address ARP Server Address 0 0 0 0 Primary DNS Address 1689 95 11 Secondary DNS Address Connection Type 1483 Routed IP LLC se 39U Back Next Exit 15 DSL 522T ADSL Router User Guide Using the Setup Wizard For Bridge Mode connections 1 Select the specific Connection Type from the drop down menu The available Bridge Mode connection and encapsulation types are 1483 Bridged IP LLC and 1483 Bridged IP VC Mux 2 If you are instructed to change the VPI or VCI number type in the correct setting in the available ent
78. rnet Connections window click the Internet Options icon 4 In the Internet Properties window click on the Connections tab and click on the LAN Settings Note button 5 Verify that the Use a proxy server for your LAN These settings will not apply to dial up or VPN connections option is NOT checked If it is checked click in the checked box to deselect the option and click OK Alternatively you can access this Internet Options menu using the Tools pull down menu in Internet Explorer Login to Home Page To use the web based management software launch a suitable web browser and direct it to the IP address of the Router Type in http followed by the default IP address 192 168 1 1 in the address bar of the browser The URL in the address bar should read http 192 168 1 1 A dialog box prompts for the User Name and Password Type in the default User Name admin and the default Password admin then click the OK button to access the web based manager Please enter your user name and password on DSL 522T User name admin Ke Remember my password Enter Password You should change the web based manager access user name and password once you have verified that a connection can be established The user name and password allows any PC within the same subnet as the Router to access the web based manger ADSL account user name and password needed for PPPoE PPPoA connections to access the Note Internet
79. rt Trap Community name Trap Version Drop down menu allows you to select SNMP v1 or SNMP vZC 47 DSL 522T ADSL Router User Guide Filters Filter rules in the Router are put in place to allow or block specified traffic The Filter Rules however can be used in a single direction to examine and then Allow or Deny traffic for Inbound WAN to LAN or Outbound LAN to WAN routed data The rules are based on IP address and TCP UDP port Configure the filter rules as desired and click the Apply button to create the rule The newly created rule appears listed in the Outbound Filter List at the bottom of the window The table below describes the various parameters that are configured for the filter rules Filters are used to allow or deny LAN or WAN users from accessing the internet or internal Network Outbound Filter Inbound Filter Filters are used to allow or deny LAN users from accessing the internet Source IF Any IP wc Destination IP AnP el source Port l Destination Port Protocal TCPDF w Action Allow e 420 0 Apply Cancel Help ID Source IP Destination IP Prot Act Enable Filters window To modify any previously created filter rule click on the note pad icon in the right hand column of the Filter List for the set you want to configure Adjust the settings as desired and click the Apply button to put the new settings into effect First determine the direction of the traffic you want the rul
80. ry fields Most users will not need to change these settings The Internet connection cannot function if these values are incorrect 3 Click Next to go to the next window and complete the Setup Wizard A DSL 5227 Microsoft Internet Explorer setting Bridge Mode Enter the bridge information provided to you by your ISF Click Next to continue VP vel Connection Type 483 Bridged IP LLC kl 39U Back Next Exit 16 DSL 522T ADSL Router User Guide Using the Setup Wizard Finish and Restart Finally you can confirm that the setup process is completed If you are satisfied that you have entered all the necessary information correctly click the Restart button to save the new configuration settings and restart the Router If you need to change settings from a previous window click the Back button 2 DSL 522T Microsoft Internet Explorer E E 2 DSL 522T Microsoft Internet Explorer E O ES D Link DSESIIHADSE ROUET D Link W cke inkl ROUTCE Do not turn the Router off while it is restarting After the Router is finished restarting you are now ready to continue to configure the Router as desired You may want to test the WAN connection by accessing the Internet with your browser 17 DSL 522T ADSL Router User Guide WAN To configure the Router s basic configuration settings without running the Setup Wizard you can access the windows used to configure WAN LAN DHCP and DNS settings directly from the Home directory
81. s admin DSL 522T ADSL Router User Guide Network Connections Network connections are provided through the ADSL port the Ethernet port and the USB port on the back of the Router See the Rear Panel diagram above and the illustrations below for examples See Installing the USB Driver above for a description of the USB driver installation procedure Connect ADSL Line Use the ADSL cable included with the Router to connect it to a telephone wall socket or receptacle Plug one end of the cable into the ADSL port RJ 11 receptacle on the rear panel of the Router and insert the other end into the RJ 11 wall socket If you are using a low pass filter device follow the instructions included with the device or given to you by your service provider The ADSL connection represents the WAN interface the connection to the Internet It is the physical link to the service provider s network backbone and ultimately to the Internet Connect Router to Ethernet The Router may be connected to a single computer or Ethernet device through the 10 100 BASE TX Ethernet port on the rear panel Any connection to an Ethernet concentrating device such as a switch or hub must operate at a speed of 10 100 Mbps only When connecting the Router to any Ethernet device that is capable of operating at speeds between 0 100Mbps be sure that the device has auto negotiation NWay enabled for the connecting port Use Category 5 or better twisted pair Ethernet cable with
82. s Colonies 11 B 1000 Brussels Belgium TEL 32 0 2 517 7111 FAX 32 0 2 517 6500 URL www dlink be Poland Budynek Aurum ul Walic w 11 PL 00 851 Warszawa Poland TEL 48 0 22 583 92 75 FAX 48 0 22 583 92 76 URL www dlink pl Hungary R k czi t 70 72 HU 1074 Budapest Hungary TEL 36 0 1 461 30 00 FAX 36 0 1 461 30 09 URL www dlink hu Singapore 1 International Business Park 03 12 The Synergy Singapore 609917 TEL 65 6774 6233 FAX 65 6774 6322 URL www dlink intl com Australia 1 Giffnock Avenue North Ryde NSW 2113 Australia TEL 61 2 8899 1800 FAX 61 2 8899 1868 URL www dlink com au India D Link House Kurla Bandra Complex Road Off CST Road Santacruz East Mumbai 400098 India TEL 91 022 26526696 56902210 FAX 91 022 26528914 URL www dlink co in Middle East Dubai P O Box 500376 Office 103 Building 3 Dubai Internet City Dubai United Arab Emirates Tel 971 4 3916480 Fax 971 4 3908881 URL www dlink me com Turkey Ayazaga Maslak Yolu Erdebil Cevahir Is Merkezi 5 A Ayazaga Istanbul Turkiye TEL 90 212 289 56 59 FAX 90 212 289 76 06 URL www dlink com tr Egypt 19 El Shahed Helmy El Masri Al Maza Heliopolis Cairo Egypt TEL 202 414 4295 FAX 202 415 6704 URL www dlink me com Israel 11 Hamanofim Street Ackerstein Towers Regus Business Center P O B 2148 Hertzelia Pituach 46120 Israel TEL 972 9 9715700 FAX 972
83. s clock with e ka e Automatic Simple Metwork Time Protocol our computer s clock Manual Enter your own settings PFE vaso Apply Cancel Help Time menu To configure system time on the Router select the method used to maintain time The options available include SNTP using your computer s system clock default or set the time and date manually If you opt to use SNTP you must enter the SNTP server URL or IP address Click the Apply button to set the system time 60 DSL 522T ADSL Router User Guide Remote Log Us the Remote Log Settings window to set up logging to servers or computers that are located outside the LAN or subnet of the Router Home Advanced ols Status y TT Log Level Notice sl Add an IF Address Achi Mone Select a logging destination O O OQ Apply Cancel Help Remote Log Settings window Select the Log Level from the pull down menu The levels available are Alert Critical Debug Error Info Notice Panic and Warning Type in the IP address of a receiver for the log message in the Add an IP Address field and click on the Add button Log message receivers that are added appear listed in the Select a logging destination pull down menu These may be used at any time for other types of log messages To remove a log message receiver from the list select it and click on the Remove button Click the Apply button when you have configured the log message receivers Remember to save the
84. s in both directions 54 DSL 522T ADSL Router User Guide PPP When the WAN connection is configured for either PPPoA or PPPoE you can configure the Router s PPP session to remain on all the time or to disconnect after some period of no activity You may also choose to instruct the Router to connect each time you want to access the WAN or the Internet Tools Status Hel This page is used to view and PPP connection status and setting Put PO Connection Setting Mot Connected Connection Setting Always ON Recommended O Connection On Demand Connection will close if idle for minutes O Manual Use Connect Disconnect button only v Y 0 Apply Cancel Help ATM VCs List ID PYE Connection Type 1 PEO PPPoE PPP Connection window If you want the Internet or WAN connection to be available any time a host on your LAN requests access select the Always On option If your ISP account is billed according to the amount of time the Router is connected choose the Connection On Demand option You can configure an idle time in minutes to disconnect the PPP connection after a period of inactivity This will discontinue the PPP session and require a few seconds to reconnect when a host requests access to the WAN Alternatively you can choose the Manual option and use the Connect button to initiate a PPP connection each time you want to use the Router to access the WAN If you use the Manual option you must return to this menu and cl
85. s you have been instructed to change them However if you are instructed to change the VPI or VCI values type in the values assigned for your account Leave the PVC and Virtual Circuit setting at the default cv and Enabled values for now This can be used later if you are configuring multiple virtual circuits for your ADSL service For more information see the section on ATM VC Settings later in this manual Under the Static IP heading choose the Connection Type from the pull down menu This defines both the connection type and encapsulation method used for your ADSL service The available options are Bridged IP LLC Bridged IP VC Mux Routed IP LLC Routed IP VC Mux or IPoA If have not been provided specific information for the Connection Type setting leave the default setting Change the IP Address Subnet Mask Gateway Address and if available Secondary DNS Server IP address as instructed by your ISP These are the global IP settings for the WAN interface This is the visible IP address of your account Your ISP should have provided these IP settings to you For IPoA Classic IP over ATM connections you may need to type in an additional IP address for a ARP Server Address If you are using an IPoA connection ask your ISP if it is necessary to use an ARP Address Resolution Protocol server Leave the MTU value at the default setting default 7400 unless you have specific reasons to change this see table below NAT should rema
86. scan protection is designed to block attempts to discover vulnerable ports or services that might be exploited in an attack from the WAN The Service Filtering options allow you to block FTP Telnet response Pings etc from the external network Check the category you want to block to enable filtering of that type of packet When you have selected the desired Firewall policies click the Apply button to enforce the policies Remember to save any configuration changes RIP The Router supports RIP v1 and RIP v2 used to share routing tables with other Layer 3 routing devices on your local network or remote LAN Tools Status Help RIP is an Internet protocol you can setup to share routing table information with other routing devices on your LAN atyourlSP s location or on remote networks connected to your network via the ADSL line RIP Disabled zl Protocol Direction 420 0 Apply Cancel Help RIP System Wide Configuration window To enable RIP select Enabled from the RIP pull down menu select the Protocol RIPv1 and RIPv1 Compatible and Direction n Out or Both and click Apply The RIPv1 Compatible option will transmit RIPv2 broadcast packets and receive both RIP v1 and RIP v2 packets The direction configuration refers to the RIP request Select In to allow RIP requests from other devices Select Out to instruct the Router to make RIP requests for routing tables from other devices Select Both to share routing table
87. setting leave the default setting Some ISPs record the unique MAC address of your Computers Ethernet adapter when you first access their network This can prevent the Router which has a different MAC address from being allowed access to the ISPs network and the Internet To clone the MAC address of your Computers Ethernet adapter type in the MAC address in the Cloned MAC Address field and click the Clone MAC Address button Leave the MTU value at the default setting default 7400 unless you have specific reasons to change this see table below NAT should remain Enabled If you disable NAT you will not be able to use more than one computer for Internet connections NAT is enabled and disabled system wide therefore if you are using multiple virtual connections NAT will disabled on all connections The Firewall should remain enabled for most users If you choose to disable this you will not be able to use the features configured in the Firewall Configuration and Filters windows located in the Advanced directory See the next chapter for more details on these windows Most users will not need to change ATM settings If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection See the section on ATM Traffic Shaping later in this manual for a further description of the parameters available for ATM traffic shapi
88. sing the WAN Settings window The connection is setup as a bridged connection Status Hel VH VC Virtual Circuit WAN Setting Connection Type service Category UBR ze PCR kbps SCR kbps v Y 0 Apply Cancel Help Configure new PVC The new PVC that appears can be configured separately in other windows availailable in the Advanced directory 40 DSL 522T ADSL Router User Guide Advanced Router Management This chapter introduces and describes the D Link DSL 522T management features that have not been ie ADSL Router presented in the previous chapter These include the more advanced features used for network management and security as well as administrative tools to manage the Router view statistics and other information used to examine performance and for troubleshooting Status Use your mouse to click the directory tabs and window buttons in order to display the various configuration and read only windows discussed below The table below summarizes again the directories and menus available in the management web interface In this chapter you will find descriptions for the windows located in the Advanced Tools and Status directories Directory Configuration and Read only Windows Click the Home tab to access the Setup Wizard WAN Settings LAN Management IP Configuration DHCP Settings for LAN Setup DNS Configuration and Dynamic DNS Conf
89. t can be located from the Internet if the public IP address changes DDNS requires that an account be setup with one of the supported DDNS providers Tools Status The DONS Configuration allows the user to setthe configuration of CONS DDNS Server Disable DDNS Server Y User Configuration UserName UserName PassWord leggeeeee Hostilame HostName e o e Apply Cancel Help Dynamic DNS Configuration window Note DDNS requires that an account be setup with one of the supported DDNS servers prior to engaging it on the router This function will not work without an accepted account with a DDNS server Enter the required DDNS information and click Apply to set this information in the Router DDNS Parameters Description DDNS Server Select one of the DDNS registration organizations form those listed in the pull down menu Available servers include DynDns org and Nol com Username or Key Enter the username given to you by your DDNS server Password or Key Enter the password or key given to you by your DDNS server Host Name Enter the host name of the DDNS server 3 DSL 522T ADSL Router User Guide Save Settings and Reboot When you have configured the DSL 522T with the settings you desire make sure you save those settings To save the system configuration settings click the Tools tab You will be presented first with the Administrator Settings window This window is described in the next chapter To save the current
90. talled for each telephone that shares the line with the ADSL line These filters are easy to install passive devices that connect to the ADSL device and or telephone using standard telephone cable Ask your service provider for more information about the use of low pass filters with your installation Operating Systems The DSL 522T uses an HTML based web interface for setup and management The web configuration manager may be accessed using any operating system capable of running web browser software including Windows 98 SE Windows ME Windows 2000 and Windows XP Web Browser Most of common web browsers can be used to configure the Router using the web configuration management software The program is designed to work best with more recently released browsers such as Microsoft Internet Explorer version 6 0 Netscape Navigator version 6 2 3 or later versions The web browser must have JavaScript enabled JavaScript is enabled by default on many browsers Make sure JavaScript has not been disabled by other software such as virus protection or web user security packages that may be running on your computer USB Port or Ethernet Port NIC Adapter Any computer that uses the Router must be able to connect to it through either the Ethernet port or USB port on the Router The easiest method of installation is via the Ethernet connection and therefore requires that your computer be equipped with an Ethernet port as well Most notebook computers
91. ting the below steps Vil DSL 522T ADSL Router User Guide The CD ROM shipped with the Router contains the USB driver software Insert the DSL 522T CD ROM into the CD drive Within a few seconds you should see a window that offers the following options Install DSL 522T Quick Install Guide View Manaual Install Acrobat Reader and Exit If you do not see this auto run pop up window explore the CD ROM and double click the setup application file autorun exe or find the file Setup exe in the folder labeled USBDRIVER and double click it to launch the installation software The auto run USB driver setup must be completed before connecting the router to your PC with the USB cable To install the driver follow these instructions 1 Click the Install DSL 522T link in the to launch the USB driver installation software Welcome to the InstallShield Wizard for D Link DSLz The InstallShield Wizard vall install D Link DSL on your computer To continue click Next lt Back Mest gt Cancel 2 Click Next on the InstallShield window D Link DS5Ls InstallShield Wizard Ready to Install the Program The wizard i ready to begin installation Click Install to begin the installation IF You want to review or change any of pour installation settings click Back Click Cancel to exit the wizard InstallShield lt Back Install Cancel 3 Click Install to begin the installation vili DSL 522T ADSL Router User Guid
92. type in the correct setting in the available entry fields Most users will not need to change these settings The Internet connection cannot function if these values are incorrect You may want to copy the MAC address of your Ethernet adapter to the Router Some ISPs record the unique MAC address of your computer s Ethernet adapter when you first access their network This can prevent the Router which has a different MAC address from being allowed access to the ISPs network and the Internet To clone the MAC address of your computer s Ethernet adapter type in the MAC address in the Cloned MAC Address field and click the Clone MAC Address button This will copy the information to a file used by the Router to present to the ISP s server used for DHCP 4 Click Next to go to the next pop up window and complete the Setup Wizard 3 DSL 5227 Microsoft Internet Explorer Sliced PELEAS LED Router Set Dynamic IP Address The Clone MAC Address is used to copy the MAC address of your Ethernet adapter to the DSL 52 T Click Next to continue WC 35 Connection Type 1403 Bridged IF LLC v Cloned WAC Address 00 20 b0 c0 00 t Clone MAC Address 9 0 Back Next Exit 14 DSL 522T ADSL Router User Guide Using the Setup Wizard For Static IP Address connections 1 Select the specific Connection Type from the drop down menu The available Static IP Address connection and encapsulation types are 1483 Bridged IP LLC 1483 B
93. u can configure the Router to direct HTTP packets to a designated HTTP server in the DMZ You can define a set of instructions for a specific incoming port or for a range of incoming ports Each set of instructions or rule is indexed and can be modified or deleted later as needed The Virtual Server options include a list of preconfigured rules listed below for commonly used protocols in the Virtual Server List To enable a preconfigured rule click the selection box for the rule you want to enable and click the Apply button A Use the LAN Clients window to select eligible IP addresses before configuring forwarding Note rules See LAN Clients below 5 Tools Status Help Connection yc k LANIP 192 168 1 2 New IP Category Available Rules Applied Rules Alien vs Predator PoAnywhere Asheron s Call Metmeetinc VPN Dark Rein 2 EverQuest SE Delta Force O Audio Video Daam O Apps Dune 000 Directx 7 0 Games EliteForce User EverQuest Fighter Ace ll Games O Servers View You must save settings and reboot to take effect o oO O Apply Cancel Help Virtual Server window 43 DSL 522T ADSL Router User Guide There are many different pre configured rules available for specific functions such as Internet gaming VPN streaming and interactive multi media standard TCP IP protocols reserved ports p2p network management applications and so on You may also create customized rules to manage T
94. u first access their network If you want to later replace the cloned MAC address with the factory default setting type in all zeros 0 0 0 0 0 0 and click the Clone MAC Address button To clone the MAC address of your computer s Ethernet adapter type in the MAC address in the Cloned MAC Address field and then click this Clone MAC Address button The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface The default setting 1400 bytes should be suitable for most users Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired such as with Internet gaming It is highly recommended that the user research how adjusting the MTU may affect network traffic for better or worse Network Address Translation may be enabled or disabled with the pull down menu Keep in mind that disabling NAT allows only a single computer to be used for Internet access through the Router NAT is enabled and disabled for the Router on all connections e PvcO Pvc7 if your Router is set up for multiple virtual connections Use this to universally enable or disable the Firewall and Filter features available in the Router If you disable this you will not be able to configure settings in the Firewall Configuration window or Filters windows in the Advanced directory 22 DSL 522T ADSL Router User Guide Static IP Address When
95. u need to view them for troubleshooting Power on Router CAUTION The Router must be used with the power adapter included with the device To power on the Router 1 Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Router and plug the adapter into a suitable nearby power source 2 You should see the Power LED indicator light up and remain lit The Status LED should light solid green and begin to blink after a few seconds 3 Ifthe Ethernet port is connected to a working device check the Ethernet Link Act LED indicators to make sure the connection is valid The Router will attempt to establish the ADSL connection if the ADSL line is connected and the Router is properly configured this should light up after several seconds If this is the first time installing the device some settings may need to be changed before the Router can establish a connection Factory Reset Button The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while the device is powered on Use a ballpoint or paperclip to gently push down the reset button Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings The device settings will be restored to the factory default IP address 192 168 1 1 and the subnet mask is 255 255 255 0 the default management Username is admin and the default Password i
96. uter will save the new settings and restart Upon restarting the Router will automatically establish the WAN connection 24 DSL 522T ADSL Router User Guide Additional settings for Static IP Address connections Static IP Parameters Connection Type IP Address Subnet Mask Gateway Address ARP Server Address IPOA connection only Primary DNS Address Secondary DNS Address MTU NAT Firewall Description This specifies the connection type and the encapsulation method used for your Static IP Address connection The options available are Bridged IP LLC Bridged IP VC Mux Routed IP LLC Routed IP VC Mux or IPoA This is the permanent global IP address for your account This is the address that is visible outside your private network Get this from your ISP This is the Subnet mask for the WAN interface Get this from your ISP This is the IP address of your ISP s Gateway router It provides the connection to the Router for IP routed traffic that is outside your ISP s network That is this will be the primary connection from the Router to most of the Internet Get this IP address from your ISP This is not required for all IPoA connections Check with your ISP for an ARP server IP address if this is necessary for your IPoA connection This is the IP address of the first choice for Domain Name Service DNS used to match the named URL web address used by most browsers with the actual global IP address used f
97. ve r Load Configuration File ia id lisis 62 Restore Factory Default Settings inci E A a E ERARE E 62 Firmware Upgrade iia 63 Miscellaneous e euer en WEE 64 PINO Ostia aa 64 IGNES et il css 64 DIagnostio Testi aa 65 no e etc A 66 DEVICE ht EE 66 O A er eee nt teeter er ia reer ie nee ae reeset E ane ene Teter neem en ae meee ee cee ore trae 67 Beie PE O 68 US O aa eo reece o ROO PO DE anc aia eee tee ace ace eee eae E E eae 69 ADSL Stats eee Te dd 70 A iota emai dea needs on aed ean ee 71 TECHNICAL SPECIPICATIONS E 72 CONFIGURING IP SETTINGS ON YOUR COMPUTER ccccceceseeeeeeeeeeeeeeeeeeeeeeees 74 DSL 522T ADSL Router User Guide About This User Guide This user s guide provides instructions on how to install the DSL 522T ADSL Router and use it to provide Internet access for an Ethernet network or single computer If you are using a computer with a functioning Ethernet port the quickest and easiest way to set up the DSL 522T is to follow the instructions provided in the Quick Installation Guide To install the USB driver click the Install DSL 522T link on the initial pop up window that appears shortly after inserting the CD and follow the instructions as they are presented If the window fails to open explore the CD double click the autorun exe file or find the file Setup exe in the folder labeled USBDRIVER and double click it to launch the installation software Before You Start Please read and ma
98. y be done through the local or external interface to test connectivity to known IP addresses The diagnostics feature executes a series of test of your system software and hardware connections Use this window when working with your ISP to troubleshoot problems Home Advancea The diagnostics feature executes a series oftest of your system sofware and hardware connections Use the feature when working with your ISF to troubleshoot problems Virtual Circuits Jpc test This Fage is used for performing diagnostics on the system ia ce Testing Connectivity to modem Testing Ethernet LAN connection PASS Testing ADSL Connection PASS Testing Network Connection Testing ATM OAM segment ping PASS r Ping Primary Domain Names Server Diagnostic Test window 65 DSL 522T ADSL Router User Guide Status Use the various read only windows to view system information and monitor performance Device Info Use the Device Information window to quickly view basic current information about the LAN and WAN interfaces and device information including Firmware Version and MAC address Home _ Advanced Tools Firmware version V3 00B01T01 EU 7 00607 10 LAN MAC Address O0 e0 bO cO do tf IP Address 192 168 1 1 Subnet Mask 255 255 255 0 DHCP Server Enabled NAT Enabl
99. y be reserved so that the lease does not expire for the LAN IP address Click the Reserve box for the address or addresses you want to reserve and click the Apply button These addresses will become Static IP addresses and will no longer be available for DHCP assignment 46 SNMP DSL 522T ADSL Router User Guide Simple Network Management Protocol is a standard for internetwork and intranetwork management Name Location Contact Tools Status Help Enable SNMP Agent Enable SNMP Traps DSL 522T DLink support diink com vendor OID 1 3 6 1 4 1 294 Access Right Destination IF Trap community Trap Version OO oO O Apply Cancel Help SNMP Management window Configure these parameters for SNMP on the Router SNMP Category SNMP Management Community Parameters This is used to enable or disable SNMP Agent and SNMP Traps or edit client SNMP Name Location and Contact o Enable SNMP Agent Click to select enable or disable SNMP Agent o Enable SNMP Traps Click to select enable or disable SNMP Traps Use this edit client community for server SNMP access o Name Edit community Name o Access Right Access Right may choose ReadOnly or ReadWrite The management agent can send an event notification to the management system to identify the occurrence of conditions such as threshold that exceeds a predetermined value Destination IP Insert destination IP address to launch trap message Trap Community Inse
100. you must first install the USB driver Follow the installation instructions below to install the USB driver Packing List Open the shipping carton and carefully remove all items Make sure that you have the items listed here e One DSL 522T ADSL Ethernet Router e One CD ROM containing the User s Guide USB driver and Quick Installation Guide e One twisted pair telephone cable used for ADSL connection e One straight through Ethernet cable e One USB cable e One AC power adapter suitable for your electric service e One Quick Installation Guide DSL 522T ADSL Router User Guide Installation Notes In order to establish a connection to the Internet it will be necessary to provide information to the Router that will be stored in its memory For some users only their account information Username and Password is required For others various parameters that control and define the Internet connection will be required You can print out the two pages below and use the tables to list this information This way you have a hard copy of all the information needed to setup the Router If it is necessary to reconfigure the device all the necessary information can be easily accessed Be sure to keep this information safe and private Low Pass Filters Since ADSL and telephone services share the same copper wiring to carry their respective signals a filtering mechanism may be necessary to avoid mutual interference A low pass filter device can be ins

D-Link DSL-522T User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents