Coleman 2000002596 User's Manual
Contents
1. tent 2 Press hook fastener flaps on underside of Rainfly onto loop pads on ends of tent to secure Fig 17A 3 Wrap hook amp loop fastener on underside of Rainfly around center Leg Poles at front and back of tent Fig 17B 4 Insert metal hook on elastic straps on Rainfly into the hole on each Leg Pole Fig 17 amp 17C Side of Tent Front of Tent 5 Stretch guylines until taut then secure with stakes Fig 17D Self rolling Windows CAUTION Springs may have sharp edges Handle with care to avoid injury Keep out of reach of children NOTE Carefully unroll metal springs stored in bag with stakes The color marking on each spring should match the color of the fabric flag sewn to the window or door sleeve opening Fig 18 1 Locate sleeve s in window panel open hook amp i loop fastener then insert spring s with match ing color marking Fig 18 amp 19 NOTE When inserting into the sleeve s the color marking on the spring s should always face the operator Close hook amp loop fastener to secure Before unzipping and opening the window push in at top to engage spring s to activate the self rolling feature Fig 20 4 Unzip to allow the window panel to roll down automatically zip back to close window panel Fig 21 amp 22 NOTE Repeat steps above for inserting the color matching spring s into sleeve s for the rest of the window2. G Keep all flame and heat sources away from this tent fabric This tent meets the flammability requirements of CPAI 84 The fabric may burn if left in continuous contact with any flame source The application of any foreign substance to the tent fabric may render the flame resistant properties ineffective The Coleman Company Inc e 3600 N Hydraulic e Wichita Kansas 67219 1 800 835 3278 www coleman com MADE IN CHINA e PRINTED IN CHINA 2009 The Coleman Company Inc Coleman amp and are registered trademarks and Rockwall is a trademark of The Coleman Company Inc 4010004524 20090515 ANI HOLILS
3. Pole while Color Code Description Qty Length Replacement Part No aye l twisting lower Leg Pole section Green 1 610mm 5010000627 counterclockwise Fig 8 i Orange 10 670mm 5010000628 e Pull up on top Leg Pole section until Leg Pole tent is taut Section Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole Repeat on remaining Leg Poles 10 Locate Frame Clips on front and back of tent then attach to Leg Poles as shown Fig 9 11 Insert plastic stakes through web straps located at bottom of each Leg Poles then drive in to secure Fig 10 CAUTION Springs may have sharp edges Handle with care to avoid injury Keep out of reach of children Button Center Hole Lower Hole To Set Up Tent 1 Unfold tent and spread out on a clean level surface with the door facing the desired direction Lower Leg Pole Section Fig 1 Ig ia Leg Poles short 4 Leg Poles long 2 2 Assemble six steel shock corded Leg Poles Fig 1 3 Push down on steel button on tapered end and insert into end with four holes NOTE Make sure steel button locks into Aube ie Rigid Door Assemble Vertical Door Pole shorter black pole with plastic tips third hole on pole as shown Fig 2 Assemble three steel shock corded curved then insert through zippered vertical pole sleeve on hinged side of door Fig 11 Ridge Poles Fig 1 2 In
4. STITCH LINE ROCKWALL 12 TENT MODEL 2000002596 Before you begin Read all instructions before set up e Select a level site clear of rocks branches and other hard or sharp objects to install your tent WARNING Keep clear of overhead power lines e Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather e Secure with all stakes and guylines provided to prevent property damage Or personal injury e For best results in windy conditions position narrow end of tent into the wind e Enlist the help of at least one other person to assist you when it is time to assemble the tent Curved Ridge Pole Curved Ridge Pole in Curved Ridge Pole in sleeve sleeve with Red Marking in sleeve Short Leg Pole Front of Tent 8 Rotate all six Leg Poles upright and insert pin on each web loop at the side locations as shown Fig 7 amp 7A Pole Descriptions Pole Pole Pole Description Qty Dia Repair Kit Replacement Kit Long Leg Pole steel w red marking 2 19mm N A 9010000678 Short Leg Pole steel 4 19mm N A 5010000680 Curved Ridge Pole steel w red marking 1 19mm N A 5010000677 Curved Ridge Pole steel 2 19mm N A 5010000679 Vertical Door Pole black short w rubber tips 1 63mm 5010000543 5010000545 Door Pole black long w rubber tips 1 63mm 5010000543 5010000545 Self Rolling Window Spring Descriptions Stretch tent to finished size Push in button on Leg
5. in carry case Remove rainfly spread out on floor of tent then unzip door amp vents before taking tent down for storage Neatly fold tent to width of pole storage bag place on tent roll tightly and place in carry case Store in a clean dry area f ol Go N Things You Should Know Under certain conditions cold weather high humidity etc condensa tion will form on the inside of your tent Condensation is caused by water vapor from your breath perspiration or any wet clothing inside the tent It is NOT LEAKAGE through the tent fabric It can be minimized by removing wet clothing from your tent and by providing good ventila tion through the tent Tree limbs tree sap bird droppings or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame resistant properties Never store tent even for a short period of time without drying it thoroughly and brushing off caked dirt Do not pack stakes or poles inside your tent Use a separate storage bag Stakes should be removed by pulling on the stake itself NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY Tent poles should not be left telescoped together during storage Do not leave your tent set up for weeks at a time Be aware that exposure to ultraviolet rays from the sun can seriously damage material and or cause it to become discolored WARNIN
6. s GO N engage spring s es CAUTION All springs must be removed from sleeves before tearing down tent to avoid damage to the tent fabric or part To avoid injury carefully roll up springs Keep out of reach of children Store rolled springs in bag with stakes Cooler Access The smaller zippered opening at the back of tent is designed for added ventilation and easy access to your beverage cooler 1 To use as a vent unzip flap to expose screen Fig 23 2 To use as a cooler access unzip other flap to make an avenue to bring beverages into tent Fig 24 Electrical Cord Access 1 Unzip access panel in the lower right corner of tent and bring in electrical cord NOTE Use only UL approved cords rated for outdoor usage Fig 25 Tent Lighting System Your tent comes pre wired with the Coleman Tent Lighting system See manual that came with the light and carefully read all instructions before use then save for future reference Attaching Room Divider 1 Divider Panel can be installed through center of the tent by inserting toggles through the top and bottom fabric loops as shown Fig 26 amp 27 Divider Panel To Store All springs must be rolled up and placed in bag with stakes All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case Make sure tent is clean and dry before placing
7. sert end of Vertical Door Pole into bottom hinge plate apply Stretch four corners of tent until taut then pressure to form a slight bow then insert other tip of pole into top drive plastic stake web strap of each to hinge Zip up vertical pole sleeve Fig 12 amp 13 secure Fig 3 3 Assemble Door Pole longer black pole with plastic cap tips then insert into zippered pole sleeve at top of door Fig 14 4 Insert end of Door Pole into top hinge plate apply pressure to form a bow then insert other tip of pole into the bottom hinge Fig 15 5 Zip up pole sleeve to enclose Door Pole Fig 16 Insert Ridge Pole with red marking into center sleeve on top of tent with the red trim Fig 4 amp 6 Insert the remaining curved Ridge Poles into the other two sleeves on top of tent Insert curved end of Leg Pole with red marking into the ends of the Ridge Pole with red dot Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles Fig 5 amp 6 Ridge Pole with lt a Red Marking sa T s Curved Ridge Pole with Red Marking Vertical Pole Sleeve i a it iy Pole Hing oe 7 sean continued on other side To Attach Rainfly 1 Drape Rainfly over tent Make sure seams on Rainfly are facing down and centered over curved Ridge Poles at sides of the tent as shown Fig 17 NOTE Large hook and loop fasteners located at the ends underside of Rainfly should be centered over ends of
Download Pdf Manuals
Related Search