Code Alarm CA100 User's Manual
Contents
1. Press One Chirp Two Chirps Transmitter LED one pulse LED two pulse Factory Default Setting Shock Sensor Program Mode Tan Wire Trunk Channel 3 Output Gray Wire Two Step Door Unlock Output Car Jacking Off Car Jacking On Exit Turn Ignition to ON position or leave it for 15 seconds Three long chirps to confirm exit Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position i Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is heard then release the valet switch You are now in the Alarm feature Shock Sensor programming mode 3 Press and hold f button for 2 seconds One long siren chirp to indicate the unit is ready to accept adjustments for the second stage of the shock sensor full alarm 4 Press mi button on the transmitter once will decrease sensitivity level by one each time an decrease is made the siren chirp will respond with 1 chirp while 2 chirp indicates the minimum of sensitivity 5 Press ft button on the transmitter once will increase sensitivity level by one each time an increase is made the siren horn chirp will respond with 1 chirp while 2 chirp indicates the maximum of sensitivity CA100 2 CODSAMIrRM 05 0406 6 Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor a Activate the warn away first stage the shock sensor the siren will emit a short chirp b Activate th2. the button is not pressed the alarm will automatically stop after 30 seconds TRIGGER THE SYSTEM When armed your vehicle is protected as follows 1 Light impacts will trigger the warn away signal A long chirp from siren horn 2 Heavy impacts Doors open Hood open Trunk open Turns on the ignition switch will trigger the programmed sequence The starter disable relay if installed prevents the vehicle s starter from cranking The siren and parking lights will turn on to alerting of an intrusion for 30 seconds Then it will stop and automatic reset and re arm If the one of sensors or detectors still active the alarm system will sound a maximum of 6 times of 30 seconds cycles ANTI CAR JACKING Warning If you don t need the car jacking function in this alarm system be sure to set car jacking feature OFF This system is default setting car jacking OFF Active Anti Car Jacking 1 Upon ignition is On press and hold the transmitter isl and a buttons at the same time for 2 seconds The parking lights will turns on for 1 5 seconds to indicate the system enters the car jacking mode 2 Once the system in car jacking mode If you are forced from the vehicle the system will be trigger when the door is opened and closed while the ignition is ON Trigger The Car Jack Mode a 50 seconds after the system has been triggered The siren will start chirping for 15 seconds b During this 15 seconds period of chirpi
3. CODSAMIrRM 05 0406 MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION amp OPERATION INSTRUCTIONS WIRING DIAGRAM Black Antenna Wire Valet Switch Blue Wire 200mA Unlock Pulse i Green Wire 200mA Lock Pulse MAIN 5 PIN WIRE HARNESS 5 Red Wire 12V To Constant Battery Source 6 PIN MINI CONNECTOR WIRE HARNESS 1 Violet Wire Positive Door Pin Switch Input alk wea 2 Blue Wire Instant Trigger Ground Input 0 Bian j Ne 3 Green Wire Negative Door Pin Switch Input Cn 12V 7 oy 4 Pink Wire To Ignition Switched 12V RO Te Cut From ignition switch x To start solenoid 5 Orange Wire 200mA Grounded when armed Red wire 30 White wire 6 Tan Wire 200mA Programmable Output Yellow wire 85 87a 86 Orange Channel 3 2 Step Door Unlock i wire A PROGRAMMING TRANSMITTER TRANSMITTER Note This mode will only retain the last 4 remote transmitters programmed If the transmitter memory is exceeded the security system will start deleting transmitters from memory in chronological order 1 Turn the Ignition switch OFF ON 3 TIMES and stay in ON position Within 15 seconds 2 Push the Valet switch 3 times and holding in on 3rd push until a long chirp is heard then release the valet switch You are now in the Transmitter programming mode 3 Press and hold any button of the transmitter until the siren responds with a confirming chirp indicating the signal has been stored in
4. ashes pause Trigger on Dual Zone Shock Sensor On solid Valet mode 5 flashes pause Trigger on Ignition switch CHIRP INDICATORS PARKING LIGHT 2 chirps Disarm 3 chirps Ajar Warning 4 chirps Disarm Intrusion ACTIVE ARMING LOCK amp ARM 1 Press ff button on transmitter 2 The siren will chirp once and parking light will flash once indicating that the system is now armed The vehicle doors will lock upon arming when interfaced with the security system Ajar Warning If the siren sounds 3 chirps then you have left a door trunk or hood lid ajar Silent Arming Disarming Press the f and buttons at same time will arm or disarm your security system No chirp sound will be heard arm disarm confirmation will be through the vehicles parking lights only Shock Sensor By Pass Press the button twice within 3 seconds will arm the security system by pass the shock sensor The system will chirp one additional time to confirm the sensor bypass mode was activated The sensor bypass feature is programmed to activate for one arming cycle only The security system will return to normal operation during the next arming cycle PASSIVE ARMING Active arming disarming is controlling your security system via the remote transmitter This security system is equipped with an optional Passive Arming feature which allows the security system to arm 30 seconds after the last door is closed Operation is as follows 1 Turn the igniti
5. e full alarm second stage the shock sensor the siren will emit a long chirp 7 When you are satisfied with the second stage the shock sensor setting press and hold f and a button at the same time for 2 seconds Two long siren chirps to indicate the unit is ready to accept adjustments of the first stage the shock sensor warn away 8 Follow the step 4 5 and 6 to adjust the warn away sensitivity 9 When you are satisfied with the setting press and mi buttons at the same time One long siren chirp to indicates the unit has locked in the adjustment Note If 30 seconds of inactivity expire or turn on the ignition during of above steps the unit will exit the program mode and return to the disarmed mode Three long chirps will confirm exit OPERATION MANUAL TRANSMITTER OPERATION Transmitter Button System Function Remark a Arm amp Lock door 2 a Arm amp Delete The Shock Sensor Press twice within 3 seconds Car Locator Upon Armed im 3 seconds Panic function Press and hold for 3 seconds a Disarm amp Unlock Door a a Disarm amp Two Steps Door Unlock Press twice within 3 seconds a 2 seconds Disarm amp Pop Trunk Release Press and Hold for 2 seconds m 2 seconds Activate Car Jacking Upon Ignition on LED INDICATORS LED Function LED Function Off Disarmed 2 flashes pause Trigger on trunk hood Slow flash Armed 3 flashes pause Trigger on door switch Fast flash Passive arming 4 fl
6. it Turn Ignition to ON position or leave it for 15 seconds Three long chirps to confirm exit ALARM FEATURE Il PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position 2 Push the Valet switch 4 times and holding in on the 4 push until two chirps with a long chirp is heard then release the valet switch You are now in the Alarm feature II programming mode 3 Press and release the transmitter button A corresponding to the feature A you want to program Press One Chirp Two Chirps Three Chirps Transmitter LED one pulse LED two pulse LED three pulse Button Factory Default Setting 1a 0 9 second Door lock 3 0 second Door lock pulse Double pulse unlock pulses Active arming Passive arming without Passive arming with passive passive door locking door locking Ignition controlled door locks Without ignition controlled amp unlocks door locks amp unlocks Exit Turn Ignition to ON position or leave it for 15 seconds Three long chirps to confirm exit ALARM FEATURE Ill PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position 2 Push the Valet switch 6 times and holding in on the 6 push until three chirps with a long chirp is heard then release the valet switch You are now in the Alarm feature Ill programming mode 3 Press and release the transmitter button A corresponding to the feature A you want to program
7. ng you will be alerting to push the valet switch once to turn off the car jacking feature If not it will enter second timer car jacking c 65 seconds after the system has beer triggered The siren starts alarming and the parking light starts flashing d 90 seconds after the system has beer triggered 1 The siren still alarming and the parking light flashing and 2 The starter disable will activate to prevent the vehicle from starting 3 It will remain active until the vehicle s battery power exhausted Override The System To Turn Off Car Jacking Turn the ignition switch from OFF to ON and within 10 seconds push valet switch the siren will stop and the system disarmed CAR LOCATOR Upon armed press i button on the transmitter to active car locator function The siren will chirp 6 times The parking light will flash 12 times for you to easily locate your car CA100 4 CODSAMIRM 05 04 06 This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CA100 3
8. on to the OFF position and exit the vehicle 2 After all entrances are closed the security system LED will flash fast for 30 seconds If you reopen any door hood trunk the security system LED will stop flashing It will begin flashing again once the vehicle all entrances are closed 3 After 30 second timer has elapsed the security system will automatically ARM The siren will chirp 1 time and the parking lights will flash 1 time PASSIVE DOOR LOCKING CA100 3 Parking light 1 flash Arm 2 flashes Disarm 3 flashes Disarm Intrusion 12 flashes Car Locator CODSAMIrR M 05 04 06 The vehicle doors will automatically lock after passive arming cycle has been completed ACTIVE DISARMING UNLOCK amp DISARM 1 Press m button on the transmitter 2 The siren will chirp twice and parking light will flash twice to indicating that the security system is now disarmed The vehicle doors will unlock disarming when interfaced with the security system Tamper Disarm If alarm triggered upon disarm the system siren chirp 4 times parking light flash 3 times Two Step Door Unlock This feature will independently unlock the drives door only when disarming the security system Pushing the m button on the transmitter a second time within 3 seconds will unlock the entire vehicle Automatic Re Arm If this feature is selected the security system will automatically re arm itself 60 seconds after disarming with remote t
9. ransmitter Automatic rearm will cancel if any door is opened before the 60 seconds timer has elapsed DISARMING WITHOUT A TRANSMITTER The Override function may be used if the remote transmitter is lost or inoperative 1 Enter the vehicle and turn the ignition switch to ON position Alarm will sound 2 Within 10 seconds push and release the valet switch The alarm will stop sounding and enter the disarm mode You can now start and operate the vehicle normally VALET MODE The valet switch allows you to temporarily bypass all alarm function eliminating the need to hand your transmitter to parking attendants or garage mechanics When the system is in valet mode all alarm function is bypassed however the remote panic feature and remote door locks will remain operational Enter Valet Mode 1 Turn the ignition to ON position 2 Push and hold valet switch for 2 seconds until the LED turns on The LED wills remain on as long as the system is in valet mode Exit Valet Mode 1 Return to normal operation turn ignition ON 2 Push and hold valet switch for 2 seconds The LED wills turns off indicate the system are exiting the valet mode PANIC FUNCTION The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency 1 Press and hold f button on the transmitter for 3 seconds The alarm will immediately sound 2 To stop the alarming press and hold amp button on the transmitter for 3 seconds 3 If
10. to memory 4 If you have additional transmitters up to 4 that need to be programmed repeat step 3 for each transmitter CA100 1 CODSAMIRM 05 04 06 Exit Turn Ignition to OFF position or leave it for 15 seconds Three long chirps amp Three parking light flashes confirm exit B ALARM FEATURES PROGRAMMING ALARM FEATURE I PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and sta ay in OFF position 2 Push the Valet switch 2 times and holding in on 2 push until one short chirp with one long chirp is heard then release the valet switch You are now in the Alarm feature I programming mode 3 Press and release the transmitter button A corresponding to the feature A you want to change a The siren chirps and LED pause will indicate new setting b The system would advance to 2 LED flash 2 chirp The factory default setting is always 1 LED flash 1 chirp 4 Depress the transmitter button A again to change the feature again Simply keep re depressing the transmitter button A again until the module advances to your desired setting 5 Depress the transmitter button B corresponding to the feature B you want to program Press One Chirp Two Chirps Transmitter LED one pulse LED two pulse Button Factory Default Setting Chirps on Chirps off Automatic Rearm On Automatic Rearm Off Instantly Door Ajar Warning 45 seconds Delay Door Ajar error chirp Ex
Download Pdf Manuals
Related Search