CHIEF TV Mount MTTU User's Manual
Contents
1. _ 706 Li 27 81 MAX 23 62 600 16 19 MIN 3 93 100 63 S 7 406 AX 29 i 16 00 1 I 37 Com LO ANTA Ip HU T 448 LOCKING 17 63 i lag FLAG 15 75 CABLE STAND RELEASE SIRAP 7 CABLE ACCESS ANGLE MEASUREMENTS MILLIMETERS d 7 FG E A AES PES INCHES MTTU Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust2. tension adjustment nut E located inside hole AG Side View Figure 7 2 Tilt tension is adjustable by using 3 16 hex key AA in the tension adjustment nut See Figure 7 NOTE Tension should be adjusted equally on each bracket to ensure even tension distribution NOTE Due to the low profile of the Thinstall Series certain displays may have limited tilt capabilities 3 To return display to full vertical position push display back against wall until spring clips secure display in vertical position Installation Instructions MTTU Extra Spring Clip Installation for larger displays IMPORTANT Display should be held in vertical position by spring clips Listen for clicking sound when returning display to the full vertical position For larger displays a second spring clip DD may be added to each upright so that the display can be held in the full vertical position by these clips Follow steps below to install the extra spring clip 1 Removedisplay andattached uprights from wall plate A to gain access to spring clip screws 2 Pull out display from uprights to expose existing spring clips 3 Remove hex nuts and screws holding spring clips to uprights See Figure 8 4 Useremoved hex nuts and screws to install additional spring clips DD along with removed spring clips onto uprights See Figure 8 display not shown for clarity Figure
3. Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y 4 d 3 Hex Head Wrench Llave de cabeza hexagonal 80 Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions MTTU TOOLS REQUIRED FOR INSTALLATION 4 3 16 4 8mm 5 16 7 9mm c M4 included M2 5 included M3 included M4 included M5 included 3 16 included A 1 wall plate C 1 right upright a Sa D 4 E 4 F 4 J 4 M7 x 70 M4 x 12 M5 x 12 M5 x 25 K 4 L 4 M 4 N 4 P 4 Q 4 6 x 25 M8 x 25 M8 x 20 M8 x 16 M8 x 10 M8 x 40 R 4 S 4 T 4 U 4 V 4 10 shoulder was
4. 8 Cable Management NOTE For attaching and adjusting cables the MTTU mount features a kickstand to allow access without having to remove display from the wall 1 Ensure mount and display are in the upright position 2 Slowly pull bottom of display away from wall until kickstand fully reaches its down position See Figure 9 Slowly release display until kickstand locks against the wall Attach or adjust cables as necessary on back of display To disengage kickstand slightly pull display away from wall and pull down on cable management straps to release kickstand Slowly allow display to return to the wall See Figure 9 kickstand in down position D Sagl e cables typical cable management d straps A WALL Figure 9 NOTE Due to the low profile design of the Thinstall Series displays with cable connections coming straight out of the back may require 90 degree cable connectors Chief offers in wall accessories that can assist with recessing cables and connections NOTE Certain displays may have limited space available for cable management MTTU Installation Instructions 10 Installation Instructions MTTU 11 MTTU Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technolo
5. INSTALLATION INSTRUCTIONS Thinstall Medium Tilt Universal Mount S CHIEF MTTU Our Mounts Your MTTU Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Thinstall are registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the inst
6. aller s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the MTTU up to and including the display does not exceed 100 Ibs 45 4 kg The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING The depth of the display cannot exceed 2 inches 50 8 mm WARNING The MTTU fits all hole patterns between 100 x 100 mm and 600 x 400 mm WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors SAVE THESE INSTRUCTIONS Installation Instructions MTTU DIMENSIONS
7. ed if necessary NOTE Spacers may not be required depending on the type of display being mounted They will typically only be used with recessed or bump out back screens Determine which screws to use to connect interface brackets to display Use the screws that fit into the holes on the back of the display Make sure screws can make at least three full turns into mounting holes If not select longer screw from hardware kit Determine which washers and shoulder washers to use with the corresponding screw Refer to table below for details Screw Size Washers Shoulder Washers M4 use R use S M5 use R use S M6 none use T M8 none none Install four button head cap screws E Q through required washers R and shoulder washers S or T interface brackets B and C spacers U or V and into holes on back of display See Figure 4 WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 lbs 18 1 ALWAYS use two people and proper lifting techniques when installing display WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the MTTU up to and including the display does not exceed 100 Ibs 45 4 kg NOTE Make sure locking flags are in the open position before attachi
8. gies 8800 002092 Rev01 2011 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 11 11 USA International Europe Asia Pacific gt TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 I n D
9. her for shoulder washer for 25 5 4 M5 screws M6 screws Wil WI M3 M2 5 3 16 BB 4 CC 1 DD 2 anchor M4 extra spring clip MTTU Installation Instructions Assembly And Installation Wall Plate Installation Using Wood Studs 1 Determine location for mount keeping in mind display size and safety requirements 2 Use stud finder to locate studs Wall plate can be mounted on 2 x 4 wood studs that are 16 apart 3 Remove and discard two plastic shipping parts from the wall plate one from each end See Figure 1 shipping part Front of wall plate Figure 1 4 Using wall plate as template mark and then drill four 3 16 diameter pilot holes through mounting surface making sure the holes are centered in the middle of each stud Holes must be drilled at least 2 1 4 deep See Figure 2 5 Install four connector screws D through wall plate and into pilot holes using M4 Allen Head bit CC See Figure 2 Figure 2 Wall Plate Installation into Concrete Concrete Block or Brick WARNING INSTALLING THE MTTU INTO UNDERRATED OR DAMAGED CONCRETE CAN LEAD TO SERIOUS INJURY OR DAMAGE TO PRODUCT When installing into concrete only install the MTTU into concrete at least 8 in depth or into 8 x8 x16 concrete blocks Never install the MTTU into cracked chipped or flaking concrete 1 Determine location for mou
10. ng display to wall plate Flags are shown in the open position in Figure 4 NOTE Display can be adjusted horizontally as long as guide hooks are securely attached to wall plate IMPORTANT If spacers are required be sure to use screws that are longer than the spacers but of the same diameter While supporting both sides of display lift display up to the wall plate on the wall MTTU Installation Instructions 7 Slowly guide hooks on top of interface brackets on top of wall plate in desired mounting location See Figure 5 8 Slowly swing display toward wall See Figure 5 A o WALL Figure 5 9 Rotate flags on each interface bracket down to the closed position in order to lock brackets to wall plate See Figure 6 locking flag Figure 6 NOTE Flags should stay in locked position unless removing display from wall bracket NOTE Display should be held in full vertical position by spring clips on uprights For some larger displays a second spring clip DD may be required in order to hold the display in the full vertical position See Extra Spring Clip Installation Section for details Tilt Adjustment 1 Display may be tilted forward by pulling forward on the top of the display as desired See Figure 7
11. nt keeping in mind display size and safety requirements 2 Using wall plate as atemplate mark and then drill four 5 16 diameter pilot holes through mounting surface Use level to make sure wall plate is perfectly horizontal Holes must be drilled at least 2 1 4 deep See Figure 3 3 Install four 5 16 anchors BB into pilot holes drilled in Step 2 Use a hammer to lightly tap anchors into holes See Figure 3 4 Install four connector screws D through wall plate holes and into anchors See Figure 3 Figure 3 Installation Instructions MTTU Qv E Q x 4 R x 4 if necessary S or T x 4 if necessary locking flag in open position U or V x 4 if necessary Figure 4 Display Installation 1 Lay display face side down on a level non abrasive surface Lay down a cloth if necessary to avoid scratching the screen Position left and right interface brackets B and C over holes in back of display to determine which holes will be used for installation NOTE Interface brackets should be positioned so that the diamond hole in the bracket is located halfway between the installation holes in order to ensure proper weight distribution Brackets may need to be expanded to tilt position in order to expose installation holes NOTE Cable management pull straps should be easily accessible underneath the display Length of straps can be adjust
Download Pdf Manuals
Related Search