Chief Manufacturing CM6DH User's Manual
Contents
1. Figure 1 CM6DH SERIES Installation Instructions To prevent the motor box from getting damaged during shipping we have shipped it unmounted Please follow these instructions for mounting the motor box to the Floating Door track ight Dimmer 3 Plug dimmer IR repeater into side af motor box Power Supply 1 2 Plug the power supply into the side ofthe motor box 4 e Position the Infrared Receiver so that it will receive the signal fram the infrared Transmitter Secure with suppiied clamp and scr dits i BANN ia i Motor and Electronics Box Studs 1 Slide the motor box onto the Sheetal eplace while engaging the coupling sleeve the 2 washers and hexnuts IMPORTANT Tighten the hexnuts until the nd of the mounting studs are Just even with the end of the hex nuts Floating Door Track Figure 2 Installation Instructions CM6DH SERIES Hanging and Adjusting Doors 1 Remove door hanger from mechanism by removing locking screws and washers See Figure 3 Locking Screws and Washers Figure 5 Figur N ai gurea 4 Move carriages to one half open position by activating mechanism and pressing button a second time when carriage reaches desired position See Mechanism Activation section 2 Center door hanger to top of door and secure with eight flat head screws of sufficient length to support weight of2. INSTALLATION INSTRUCTIONS Automated Dual Horizontal Door System This device complies with part 15 of the FCC rules Operation is subject to the following 2 conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit other than that to vvhich the receiver is connected Consult the dealer or and experienced radio TV technician for help ka CHIEF CM6DH SERIES CM6DH SERIES Installation Instr
3. Install Light Dimmer Module Optional With the dimmer option installed cabinet lighting can be switched on or off or dimmed using the left buttons on the systems remote control To install the optional dimmer 1 Plug 115VAC lighting into the back of the Light Dimmer Module 2 Plug the other end of Dimmer Module cord into a 115VAC grounded receptacle on motor assembly CAUTION The Dimmer is for 120 volt incandescent or Halogen lamps of at least 25 watts and should not to exceed 300 watts total The system also provides the option of creating and saving two different lighting scenes Please refer to the Remote Control instructions for information on how to configure scenes Figure 8 System Activation 1 Insert plug from the power supply into the jack on the top of the motor box Top of Va Cabinet Figure 9 2 Plug Powercord into 115VAC outlet IMPORTANT A quality surge protection device is recommended 3 Make sure nothing is obstructing movement of doors 4 Press and release the Activator Button on the front of the Motor Box or the Close Door button on the Remote Control The doors should travel to the fully closed position Installation Instructions CM6DH SERIES Activator Status Trigger Control Input Mctivator J Figure 10 5 Press the Open Door button on the Remote Control NOTE If
4. MUST REMAIN ACCESSIBLE AT ALL TIMES DO NOT block or impede access to plug at any time A CAUTION Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC compliance rating and make the unit illegal to operate Installation Instructions CM6DH SERIES TOOLS REQUIRED FOR INSTALLATION PARTS CM6DH SERIES Installation Instructions INSTALLATION Cabinet Considerations 1 2 3 Header must not extend beyond top of track Guide wheel must have free play in toe space Doors must not exceed 50 Ibs each Allow ample room for drawers to open past doors and for doors to move in front of cabinet as well as above floor or carpet Use of a quality surge protection device is suggested for mounting on top of cabinet to make electrical hook up of the mechanism and lights Installing to Cabinet 1 2 3 Place mechanism A on top of cabinet See Figure 1 Align center of track with center of the door opening Attach using 8 or 10 screws through the holes in track Attach motor box to the track following instructions in box See Figure 2 Installation Instructions CM6DH SERIES Door Adjusting Carriage Screw Lockirtg Screw 6 1 4 To rear of motorbox 4 15 16 Interior Cabinet Area 1 4 Clearance 5 8 Guide Wheel Plate T 11 2 13 16 Hold for Guide Wheel Clearance
5. adifferent travel distance is required see Door Travel Adjustment below ADJUSTMENTS Adjust Door Travel Distance To adjust door travel distance 1 Press and hold the activator button on the front of the motor box for 13 seconds The Status Light on the front of the motor box will begin to blink alternately red and green When this starts to happen release the Activator Button When put into Learn Moden the system runs back and forth several times and measures its environment such as open and closed locations etc The system will then stop and remember these learned measurements Activator Status Trigger Control Input X tivator Figure 11 System Controls and Indicators Learn Mode The CM6DH system has no limit switches The system uses an encoder on the motor to collect data and send it to the micro processor s memory The software learns about its environment speed time duration stop points etc during the initial setup of the unit and retains that information until requested to relearn its environment The unit is shipped pre set from the factory and will then continually adjusts to it s enviornment on each activation If for some reason you want to place the system into Learn Mode such as to stop at other than its normal stop points Press and hold the red activator button on the front of the motor box for approxamatly 13 seconds and then release it whe
6. door See Figure 4 5 Lift door and engage guidewheel into guidewheel space 6 Tip top of door in engaging the pendant bolts into keyhole in carriage arms See Figure 6 Keyhole Figure 4 3 Attach one guidewheel plate F to bottom center of each door See Figure 5 Figure 6 7 Adjust height and alignment of doors by turning the pendant bolts See Figure 7 8 After adjustment is complete replace the washers and locking screws See Figure 7 CM6DH SERIES Installation Instructions Figure 7 IR Sensor Placement The placement of the IR sensor can be crucial to proper operation of the system A flexible IR sensor is provided to make it easier to achieve reliable operation In most applications the IR sensor may be installed on top of the cabinet However tall and or dark colored ceilings can absorb the IR signal If inconsistent operation is encountered there are two alternatives e One the flexible IR sensor eye can be placed so that it gives the sensor line of sight to the signal from the remote controller Often this merely involves placing the IR sensor so that it peeks up over the top of the cabinet It doesn t have to be much just enough to give line of sight e Two an IR sensor extension cord can be used to position the IR sensor in the cabinet near to the other remote controlled units For example near to the VCR or DVD player
7. external IR i NOTE Making a momentary dry contact closure between the reciever only common and the open closed stop or sequence will e Position 6 V out activate the system in that mode e Position 5 Vcc 5v Radio Power for external RF receiver only e Position 4 24 VDC Sequence control for use with 3rd party control e Position 3 Sequence Open Stop Close Stop e Position 2 Common Discrete control for use with 3rd party control e Position 1 Close Control Input on Front of Motor Box Open 8 1 Close Stop 7 2 Common IR reciver Input 6 3 Sequence Control Open Stop Close Stop IR reciver Input 5 4 24VDC for Powering Radio Figure 15 10 Installation Instructions CM6DH SERIES 11 CM6DH SERIES Installation Instructions A USA International A 8401 Eagle Creek Parkway Savage MN 55378 N CH i E F P 800 582 6480 952 894 6280 IZ F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Asia Pacific Room 24F Block D Lily YinDu International Building 8820 000022 RevA LuoGang BuJi Town Shenzhen CHINA 2007 Chief Manufacturing TH PFRrREFTRNECSAERGRKED 24F www chiefmfg com P 86 755 8996 9226 11 07 F 86 755 8996 9217
8. n the Status Light flashes quickly red green red green red green Activator Button Status Trigger Control InpuN Activator Ll Figure 12 The controller will then be in Learn Mode The door will move for 3 seconds stop for 10 seconds and when it starts moving again it will be in it s Learn Mode When put into Learn Mode the mechanism runs back and forth several times and measures it s environment such as open and closed locations etc and then stops and remembers these learned measurements so that next time the system runs it knows where to start and stop Status Light Codes There is a light on the front of the mechanism motor box that will tell through its pattern of flashes and colors what the mechanism is doing Status Indicator Trigger Control Input Activator dels Figure 13 Normal Doors At Rest The Status Light will be on steady green Normal Run Motion of Doors The Status Light will flash in groups of 2 green followed by a pause In normal run motion the doors on the system have a variable speed The doors will start slowly accelerate to a fast speed and then slow down before coming to a stop Doors Obstructed The Status Light will flash in groups of 3 red followed by a pause If the doors meet an obstruction they will sense the obstruction stop momentarily and move in the opposi
9. ponsibility to make sure all components are properly assembled and installed using the instructions provided Read all instructions before using this furnishing DANGER TO REDUCE THE RISK OF ELECTRIC SHOCK e ALWAYS unplug this furnishing from the electrical outlet before cleaning WARNING TO REDUCE THE RISK OF BURNS FIRE ELECTRIC SHOCK OR INJURY TO PERSONS Unplug from outlet before putting on or taking off parts Close supervision is necessary vvhen this furnishing is being used by or near children invalids or disabled persons Use this furnishing only for its intended use as directed in these instructions DO NOT use attachments not recommended by the manufacturer NEVER operate this furnishing if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the furnishing to a service center for examination and repair Reep the cord avvay from heated surfaces NEVER operate the furnishing with the air openings blocked Keep the air openings free of lint and the like NEVER drop or insert anything into any opening DO NOT use outdoors DO NOT operate vvhere aerosol spray products are being used or vvhere oxygen is being administered e To disconnect turn all controls to the off position then remove plug from outlet WARNING RISK OF ELECTRICAL SHOCK Connect this device to a properly grounded outlet only CAUTION ONE END OF POWER CORD
10. te direction for a few seconds Remove the obstruction and then activate the doors They should return to normal run motion Doors Obstructed Both Ways The Status Light will flash in groups of 4 red followed by a pause Similar to Doors Obstructed but doors are prevented from moving in either direction Remove the obstruction and then activate the doors They should return to normal run motion Travel Too Far The Status Light will flash in groups of 5 red followed by a pause The motor is running but the doors are not moving Has the motor box been uncoupled from the CM6DH SERIES Installation Instructions track or is the motor box bent causing it to become uncoupled Control Input on Front of Motor Box from the track Power Loss The Status Light will be on solid red There has been a power loss due to an electrical storm etc When next activated the doors will move at a slow speed to their full Status Thgge Control Input Actvator closed position If the doors are already closed they will not move The Status Light will return to solid green and the doors are ready for normal activation Control Input Optional Control Input Connections Control Input 8 position RJ 45 modular phone jack Discrete control for use with 3rd party control e Position 8 Open Figure 14 e Position 7 Stop IR Receiver Eye input for Eubank Inc supplied
11. uctions CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS The Alert messages DANGER WARNING CAUTION IMPORTANT and NOTE are used throughout these instructions and on the product to alert the reader and or operator of the existence of dangerous situations conditions and or important operational and maintenance information SAVE THESE INSTRUCTIONS WARNING WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions A CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY It is the installers res
Download Pdf Manuals
Related Search